Development of a Tube Plasma Ion Source for Gas Chromatography-Mass Spectrometry Analysis and Comparison with Other Atmospheric Pressure Ionization Techniques.

A tube plasma ionization (TPI) open-air source for gas chromatography-mass spectrometry (GC-MS) was developed. This source is based on an inverse low temperature plasma configuration where the pin inner electrode is applying the high voltage and the grounded electrode is the housing itself. The ionization possibilities were tested by using an EPA mix of priority contaminants, showing that 68% of the analytes could undergo both proton-transfer and charge-exchange reactions. The potential of using different discharge gases (He and Ar) to ionize the analytes and auxiliary gases (He, N2, O2, and synthetic air) to transport the ions toward the MS was carefully investigated. Additionally, the addition of water was also tested to show the different ionization trends in the TPI source. Finally, the ionization by TPI under both dry and wet conditions was compared with other gas-phase atmospheric pressure ionization sources showing TPI could ionize a wider range of compounds (97%) than atmospheric pressure chemical ionization (APCI, 95%) and atmospheric pressure photoionization (APPI, 87%). Besides, the detection capability of TPI was better than APCI and APPI, achieving instrumental limits of detection down to 3 fg on column, which demonstrates the great potential of this ionization source for GC-MS determinations.

Development of an inverse low-temperature plasma ionization source for liquid chromatography/mass spectrometry.

RATIONALE: An argon inverse low-temperature plasma (iLTP) ionization source for liquid chromatography/tandem mass spectrometry was developed. The iLTP is constructed from simple chromatographic supply materials and is implemented into an atmospheric pressure chemical ionization (APCI) source replacing the APCI discharge needle electrode. The newly developed ion source was coupled to an ultra-high-performance liquid chromatography (UHPLC) system. METHODS: The argon iLTP was characterized by optical emission spectroscopy. The soft ionization of selected standards was also demonstrated by direct infusion experiments. In addition to the use of argon as the discharge gas, helium, synthetic air, and oxygen were used, which were tested for their performance using testosterone and vitamin D3 . RESULTS: Spectroscopic measurements of the argon plasma were conducted, demonstrating the main emission band of argon metastables with corresponding energies of 11.53 eV and 11.72 eV. Infusion experiments indicate a gentle ionization by iLTP, e.g. caffeine, testosterone, reserpine, vitamin D3 , and 25-hydroxyvitamin D3 , which resulted in the corresponding protonated molecules. The splitless coupling with UHPLC (possible flow rates >1000 µL min-1 ) shows promising results in interday repeatability (n = 10) for the substances with a relative standard deviation of less than 5% and limits of detection for caffeine, testosterone, reserpine, vitamin D3 , and 25-hydroxyvitamin D3 of 10 ng L-1 , 50 ng L-1 , 500 ng L-1 , 5 µg L-1 , and 5 µg L-1 , respectively. CONCLUSIONS: The argon iLTP ion source presented in this work shows promising approaches in the field of ionization of small organic molecules. The mechanism related to the discharge gas argon has not been elucidated so far and further investigations are needed. The iLTP ion source shows a very good performance with UHPLC coupling, even at increased flow rates. It could be shown that an argon iLTP can compete with the helium dielectric barrier discharge (DBD) preferred in the literature, making it a more economical choice.

Development of a fast-switching dual (ESI/APCI) ionization source for liquid chromatography/mass spectrometry.

RATIONALE: High-throughput liquid chromatography/mass spectrometry (LC/MS) is an increasing topic in analytical chemistry. Especially the idle time of a mass spectrometer should be reduced for an efficient and cost-saving use. Therefore, a fast-switching dual ion source was developed, which uses the most important ionization techniques at atmospheric pressure, electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI), with one or more LC systems. METHODS: The performance of the developed ion source is shown by infusion experiments and chromatographic analyses of different standard substances. A high-throughput method is demonstrated by coupling two UHPLC systems to the dual ion source with a triple quadrupole mass spectrometer. RESULTS: No decrease in the ion abundance and a stable performance of the mass spectrometer are presented while using the dual ion source. Instrumental limits of detection are 30 ng L-1 for testosterone using ESI and 1 µg L-1 for vitamin D3 using APCI. A fast switching between two UHPLC systems and the dual ion source leads to a high sample throughput of 50 samples in 75 min with relative standard deviations for testosterone and vitamin D3 of 1.5% and 3.8%, respectively. CONCLUSIONS: This work presents the development of a dual ESI and APCI ion source operating simultaneously or in switched mode. The results show sensitive and reliable performance as well as the hyphenation to one or more HPLC systems.

Analysis of volatile metabolites from in vitro biofilms of Pseudomonas aeruginosa with thin-film microextraction by thermal desorption gas chromatography-mass spectrometry.

Cystic fibrosis (CF) is an autosomal recessive inherited disease which leads to a production of thickened mucus in the airways. These conditions are conducive to poly-microbial infections, like chronic lung infection, in which Pseudomonas aeruginosa (P. aeruginosa) is the major pathogenic bacterium colonizing CF lungs at the end of the lifetime of CF patients. This in vitro study uses a P. aeruginosa biofilm model under partly cystic fibrosis conditions, with a sampling of volatile extracellular metabolites. The gas sampling was done with thin-film microextraction (TFME) and commercial polydimethylsiloxane (PDMS) films, whereas the analysis of loaded films was done by gas chromatography coupled to quadrupole mass spectrometry and thermodesorption (TD-GC-qMS). For this purpose, two commercially available films were characterized by means of thermogravimetry coupled to a qMS with atmospheric pressure photo ionization (TG-APPI-qMS), regarding homogeneity and temperature stability. The selected film was cleaned using a method developed in this study. The TD-GC-qMS method was successfully used for standards of volatile metabolites which were known to be produced by P. aeruginosa. Limits of detection and quantification of the method for middle and less polar compounds in low nanomolar range (0.5 nM and 1.5 nM) were achieved. The developed method was finally applied to investigate the extracellular volatile metabolites produced by biofilms of the strain P. aeruginosa DSM 50071 under aerobic and anaerobic conditions. In sum, eleven metabolites could be found under both conditions. Furthermore, it was shown in this study that different oxygen conditions (aerobic and anaerobic) resulted in emitting different extracellular volatile metabolites. Specific metabolites, like 1-undecene (aerobic) and 2-undecanone (anaerobic), could be identified. The results are promising, in that the biofilm model may be applicable for the identification of P. aeruginosa under clinical conditions. Furthermore, the model could be the basis for studying extracellular volatile metabolites from different mono- or co-cultures of various bacteria, as well as the implementation of pulmonary conditions, like these in CF lungs. This possibility allows the development of a non-invasive "at-bedside" breath analysis method for CF patients in focus of various bacterial infections. Graphical abstract.

Development of an Atmospheric Pressure Chemical Ionization Interface for GC-MS.

A closed atmospheric pressure chemical ionization (APCI) ion source as interface between a gas chromatograph (GC) and a triple quadrupole mass spectrometer (QqQ-MS) was developed. The influence of different ion source conditions, such as humidity, make-up gas flow, and the position of the GC column, were investigated and determined as main factors to increase sensitivity and repeatability of the system. For a performance test under real conditions, the new APCI ion source was used for the determination of plant protection products in commercially available coffee beans from Vietnam. The ionization behavior was investigated and the majority of the analytes were detected as [MH]+, [M]+∙, or as characteristic fragment ions, which have been assigned to ion source fragmentation. The developed GC-MS methods are based on tandem MS (MS/MS) and revealed for the plant protection products limits of detection (LOD) between 1 and 250 pg on column and relative standard derivations for all compounds < 16%. The used ultrasonic solid-liquid extraction yielded recovery rates of approximately 60 to 100%. Residues of herbicide methyl esters, organophosphorus compounds, and organonitrogen compounds have been detected in the analyzed coffee beans.

Time-of-flight ion mobility spectrometry in combination with laser-induced fluorescence detection system.

A laser-induced fluorescence (LIF) was used as a complimentary detection system for time-of-flight ion mobility spectrometry (TOF-IMS). A LIF detection system is potentially faster than a conventional electrometer detector and can provide additional (to usual for IMS drift time) analytical information, namely wavelength of fluorescence maxima and fluorescence lifetime. Therefore, better discrimination ability can be expected. Additionally, the combination of IMS and LIF operates at atmospheric pressure. This allows fluorescence measurements of specified ions and ion clusters, which would not survive in a mass spectrometer. An IMS drift cell of open design with both the electrometer and LIF detectors was designed. The feasibility of IMS-LIF was demonstrated on the example of the Xanthene dye Rhodamine 6G (R6G). Electrospray was used as an ionization source. The release and desolvation of R6G ions from the electrospray with following IMS-LIF analysis were demonstrated. The effects of experimental parameters (e.g., ion gate and drift voltages, distance to ESI emitter) are demonstrated and discussed. The obtained results are promising enough to ensure the potential of LIF as a complimentary/alternative detection system for time-of-flight ion mobility spectrometry.

Low-temperature plasma ionization differential ion mobility spectrometry.

A low-temperature plasma (LTP) was used as an ionization source for differential ion mobility spectrometry (DMS) for the first time. This ionization source enhances the potential of DMS as a miniaturized system for on-site rapid monitoring. The effects of experimental parameters (e.g., discharge/carrier gas composition and flow rate, applied voltage) on the analysis of model aromatic compounds were investigated and discussed. It was found that the nature of reactant ion positive (RIP) is dependent on the discharge/carrier gas composition. The best response to the analyte was achieved when pure nitrogen was used as the discharge/carrier gas. The ability to perform analysis with zero helium consumption is especially attractive in view of the potential application of LTP-DMS for online (and on-site) monitoring. Analytical performance was determined with six environmentally relevant model compounds (benzene, toluene, ethylbenzene, p-xylene, 1,2,4-trimethylbenzene, and naphthalene) using LTP and directly compared to APPI and APCI ((63)Ni) ionization sources. When LTP was coupled to DMS, calculated LOD values were found to be in the range of 35-257 ng L(-1) (concentration in the carrier gas). These values are competitive with those calculated for two DMS equipped with traditional ionization sources (APPI, (63)Ni). The obtained results are promising enough to ensure the potential of LTP as ionization source for DMS.

Cross-linked Triblock Peptide Capsules as Potential Oxygen Carriers.

Perfluorodecalin (PFD)-filled capsules have been studied for over 15 years as artificial oxygen carriers. However, none of these capsules combines good biocompatibility, good mechanical stability and dispersion stability. Here we propose to use synthetic triblock peptides containing a central block of cysteine units as a cross-linking shell material for capsules with both good biocompatibility and stability. Together with outer aspartate units and inner phenylalanine units, the resulting amphiphilic triblock peptides can encapsulate PFD efficiently to prepare capsules with a suitable diameter, a certain mechanical strength, a large diffusion constant, fast gas exchange rates, and little cytotoxicity. Given the above advantages, these PFD-filled peptide capsules are very promising as potential artificial oxygen carriers.

Review on atmospheric pressure ionization sources for gas chromatography-mass spectrometry. Part I: Current ion source developments and improvements in ionization strategies.

The use of atmospheric pressure ionization (API) sources has become very popular for gas chromatography-mass spectrometry (GC-MS) determinations. GC-API-MS shows important advantages over traditional vacuum ionization sources such as a lower fragmentation preserving the molecular or quasi-molecular ion, the combination of GC separations with advanced mass spectrometers typically developed for liquid chromatography (LC) systems, a significantly higher sensitivity, or the reduction of costs due to the capability to use the same MS for both LC- and GC- couplings. For these reasons, the development of new API sources and GC-API-MS platforms has exponentially increased during the last years. Thus, this review is mainly focused on the last advances in GC-API-MS instrumentation. New setups and couplings on extensively reported API techniques as well as the development of new API sources for GC-MS coupling are thoroughly discussed. Moreover, novel ionization strategies have been reviewed to overcome some of the drawbacks of GC-API-MS methodologies.

Review on atmospheric pressure ionization sources for gas chromatography-mass spectrometry. Part II: Current applications.

The application of atmospheric pressure ionization (API) sources in gas chromatography-mass spectrometry (GC-MS) determinations is becoming more popular since they have shown great capabilities to sort out the main drawbacks of vacuum ionization techniques like electron ionization (EI) and chemical ionization (CI). The development of new API techniques and set-ups have grown in the last decades, opening the field of GC-MS to new applications and facing some of the major issues in current analytical methodologies such as the requirement of a compromise between sensitivity and selectivity. Thus, this review is mainly focused on the use of GC-API-MS in different application fields such as food analysis (food safety and food metabolomics), environmental analysis, clinical analysis, drug and pharmaceutical analysis, and petroleomics, among others. The methodologies have been critically reviewed to compare the performance of different API sources and approaches, highlighting the main contributions to overcoming some of the major limitations of the current methodologies as well as the new perspectives that GC-API-MS might open in the different fields.

Thermogravimetry coupled to an atmospheric pressure photo ionization quadrupole mass spectrometry for the product control of pharmaceutical formulations and the analysis of plasticizers in polymers.

The development of a thermogravimetry coupled to an atmospheric pressure photoionization mass spectrometry (TG-APPI-MS) with a high temperature and flexible transfer line is presented. A method was developed to analyze plasticizers in solution which consist of a solvent evaporation step and subsequent evaporation of the analyte. These solutions of dibutyl phthalate (DBP) in hexane were used to investigate the repeatability (RSD: 3.6%) and linearity (R2: 0.9995) of the new developed system. With the new device the detection of different phthalates in a standardized PVC (polyvinyl chloride) polymer is shown. On the example of ASA, the degradation of a pharmaceutical drug is investigated. The dimerization and the possible trimerization of ASA during the thermal degradation is shown. Ten tablets of different ASA manufacturers were analyzed with the new developed analysis platform. The active substance was found in every tablet. Differences in mass spectral data as well as the studying of the pack insert were used to assign the tablets to companies and their subsidiaries. A unique formulation of ASA was found to have a different mass pattern when analyzed with TG-APPI-qMS. The developed device is a promising tool for the product control and the identification of falsified drugs.

Direct inlet probe ion mobility spectrometry.

Direct inlet probe (DIP) was used as an introduction and a pre-separation step for atmospheric pressure photoionization time-of-flight ion mobility spectrometry (APPI-TOF-IMS) for the first time. IMS is an analytical technique used to separate and identify ionized molecules in the gas phase and under atmospheric pressure based on their mobility. The utilization of DIP prior to IMS gives the possibility to introduce the analytes into the gas phase and provides an additional separation based on their vapor pressure. The proof-of-principle study was done on example of eight polycyclic aromatic hydrocarbons (PAHs) with the ring number from 2 to 5, namely naphthalene, fluorene, anthracene, phenanthrene, pyrene, fluoranthene, benzo[a]pyrene, and benzo[k]fluoranthene. All these compounds are included in EPA priority pollutant list. Moreover, benzo[a]pyrene and benzo[k]fluoranthene are marked by EPA as probably carcinogen compounds and also included into SCF and EU lists. To increase the sensitivity of DIP-APPI-IMS the analysis was performed using a dopant assisted ionization method (benzene, 74mgL-1 in N2). It was found that the heating rate of the interface plays a crucial role for the whole analytical procedure. To prove the ability of this method to analyze PAHs in the mixture, the mixtures containing up to five PAHs were analyzed. The LODs for the analyzed compounds obtained with DIP-APPI-IMS were found to be in the tens- or hundreds-of-microgram-per-liter range. The obtained results are promising enough to ensure the potential of DIP as an introduction and a pre-separation step for ion mobility based methods.

X-ray ionization differential ion mobility spectrometry.

X-ray was utilized as an ionization source for differential ion mobility spectrometry (DMS) for the first time. The utilization of this ionization source increases the potential of DMS system for on-site based applications. The influence of experimental parameters (e.g. accelerating voltage, filament current, and separation field) on the analysis of model compounds was investigated and discussed. It was found that both the positive and the negative reactive ion peaks [RIP(+) and RIP(-)] formed during X-ray ionization are identical with those observed with the traditional 63Ni radioactive ion source. This is especially notable for RIP(-), because the chemistry provided by other nonradioactive sources in the negative mode is more complicated or even different than that observed with a 63Ni source. Increase of either filament current or accelerating voltage resulted in increased intensity of both RIP(+) and RIP(-). However, because of the materials used for construction of X-ray adapter the maximal level of filament current and accelerating voltage used in this study were limited to 700mA and 5kV, respectively. Analytical performance was determined with two model compounds (acetone and methyl salicylate) using X-ray and directly compared to 63Ni ionization source. When X-ray was coupled to DMS, calculated LOD values were found to be within the range of 0.17-1.52ppbv/v (concentration in the carrier gas). These values are competitive with those calculated for DMS equipped with traditional 63Ni radioactive ionization source. The obtained results are promising enough to ensure the potential of X-ray as ionization source for DMS.

Development of an electrospray-(63)Ni-differential ion mobility spectrometer for the analysis of aqueous samples.

The feasibility of an electrospray coupled with a (63)Ni-differential ion mobility spectrometer (DMS) for the analysis of water samples was proven on examples of 2-hexanone, fluoroacetamide, l-nicotine and 1-phenyl-2-thiourea water solutions. The model substances were selected in order to cover the vapor pressure range of 0.3-1467 Pa. To reduce the inline humidity, which demonstrates a strong influence on the analyte compensation voltage, two units with a desolvation region lengths of 15.5 and 7 mm were examined. The counter gas (heated to 100 °C nitrogen) with flow rates of 100 mL min(-1) and 30 mL min(-1) for short and long desolvation units, respectively, was essential for the efficient reduction of humidity. The reduction of water content in the carrier gas to 2.2-2.4 g m(-3) and to 1.8-2.0 g m(-3) for the short and long desolvation unit, respectively, was achieved at an electrospray flow rate of 1000 nL min(-1). With this adjusted experimental setup, the detection of model substances in the water solutions, in the range of 0.1-50 mg L(-1), was performed. No correlation between the vapor pressure and signal area was observed. The high stability of the inline humidity, and the correspondingly stable carrier gas flow rate, were found to be essential for an acceptable reproducibility.