Cathodic Deposition-Assisted Synthesis of Thin Glass MOF Films for High-Performance Gas Separations.

Glass metal-organic framework (MOF) films can be fabricated from their crystalline counterparts through a melt-quenching process and are prospective candidates for gas separation because of the elimination of the grain boundaries in crystalline MOF films. However, current techniques are limited to producing glass MOF films with a thickness of tens of micrometers, which leads to ultralow gas permeances. Here, we report a novel cathodic deposition-assisted synthesis of glass ZIF-62 films with a thickness as low as ~1 µm. Electrochemical analyses and deposition experiments suggest that the cathodic deposition can lead to pure crystalline ZIF-62 films with a controllable thickness of ~2 µm to ~15 µm. Accordingly, glass ZIF-62 films with a thickness of ~1 µm to ~10 µm can be obtained after a thermal treatment. The fabricated defect-free glass ZIF-62 film measuring 2 µm in thickness shows a remarkable CO2/N2 and CO2/CH4 selectivity of 31.4 and 33.4, respectively, with a CO2 permeance which is over 30 times higher than the best-performing glass ZIF-62 films in literature.

Tuning the Electrochemical Properties of Novel Asymmetric Integral Sulfonated Polysulfone Cation Exchange Membranes.

In this study, novel asymmetric integral cation exchange membranes were prepared by the wet phase inversion of sulfonated polysulfone (SPSf) solutions. SPSf with different degrees of sulfonation (DS) was synthesized by variation in the amount of chlorosulfonic acid utilized as a sulfonating agent. The characterization of SPSf samples was performed using FTIR and 1H-NMR techniques. SPSf with a DS of 0.31 (0.67 meq/g corresponding ion exchange capacity) was chosen to prepare the membranes, as polymers with a higher DS resulted in poor mechanical properties and excessive swelling in water. By a systematic study, the opportunity to tune the properties of SPSf membranes by acting on the composition of the polymeric solution was demonstrated. The effect of two different phase inversion parameters, solvent type and co-solvent ratio, were investigated by morphological and electrochemical characterization. The best properties (permselectivity of 0.86 and electrical resistance of 6.3 Ω∙cm2) were obtained for the membrane prepared with 2-propanol (IPA):1-Methyl-2-pyrrolidinone (NMP) in a 20:80 ratio. This membrane was further characterized in different solution concentrations to estimate its performance in a Reverse Electrodialysis (RED) operation. Although the estimated generated power was less than that of the commercial CMX (Neosepta) membrane, used as a benchmark, the tailor-made membrane can be considered as a cost-effective alternative, as one of the main limitations to the commercialization of RED is the high membrane price.

Cathodic Electrodeposition of MOF Films Using Hydrogen Peroxide.

Metal-organic framework (MOF) films can be made by cathodic electrodeposition, where a Brønsted base is formed electrochemically which deprotonates the MOF linkers that are present in solution as undissociated/partially dissociated weak acids. However, the co-deposition of metal and the narrow range of possible metal nodes limit the scope of this method. In this work, we propose the use of hydrogen peroxide (hydrogen peroxide assisted cathodic deposition or HPACD), to overcome these limitations. Electrochemical measurements indicate that in DMF, hydrogen peroxide is reduced to superoxide anions that deprotonate the carboxylic ligands. This single-electron reduction happens at much higher potentials than all previous reported methods. This prevents the co-deposition of metal and extends the range of possible metal nodes. Various pure MOF films (HKUST-1, MIL-53(Fe) and MOF-5) were prepared via this approach. HPACD was also used for the preparation of patterned MOF films and of flexible Cu-BTC coated paper membranes which reject 99.1 % of Rose Bengal from water with a permeance of 8.4 L m-2 h-1 bar-1 .

Template-Mediated Control over Polymorphism in the Vapor-Assisted Formation of Zeolitic Imidazolate Framework Powders and Films.

The landscape of possible polymorphs for some metal-organic frameworks (MOFs) can pose a challenge for controlling the outcome of their syntheses. Demonstrated here is the use of a template to control in the vapor-assisted formation of zeolitic imidazolate framework (ZIF) powders and thin films. Introducing a small amount of either ethanol or dimethylformamide vapor during the reaction between ZnO and 4,5-dichloroimidazole vapor results in the formation of the porous ZIF-71 phase, whereas other conditions lead to the formation of the dense ZIF-72 phase or amorphous materials. Time-resolved in situ small-angle X-ray scattering reveals that the porous phase is metastable and can be transformed into its dense polymorph. This transformation is avoided through the introduction of template vapor. The porosity of the resulting ZIF powders and films was studied by N2 and Kr physisorption, as well as positron annihilation lifetime spectroscopy. The templating principle was demonstrated for other members of the ZIF family as well, including the ZIF-7 series, ZIF-8_Cl, and ZIF-8_Br.

Reversible Optical Writing and Data Storage in an Anthracene-Loaded Metal-Organic Framework.

Metal-organic frameworks (MOFs) enable the design of host-guest systems with specific properties. In this work, we show how the confinement of anthracene in a well-chosen MOF host leads to reversible yellow-to-purple photoswitching of the fluorescence emission. This behavior has not been observed before for anthracene, either in pure form or adsorbed in other porous hosts. The photoresponse of the host-guest system is caused by the photodimerization of anthracene, which is greatly facilitated by the pore geometry, connectivity, and volume as well as the structural flexibility of the MOF host. The photoswitching behavior was used to fabricate photopatternable and erasable surfaces that, in combination with data encryption and decryption, hold promise in product authentication and secure communication applications.

Boosting the Catalytic Performance of Metal-Organic Frameworks for Steroid Transformations by Confinement within a Mesoporous Scaffold.

Solid-state crystallization achieves selective confinement of metal-organic framework (MOF) nanocrystals within mesoporous materials, thereby rendering active sites more accessible compared to the bulk-MOF and enhancing the chemical and mechanical stability of MOF nanocrystals. (Zr)UiO-66(NH2 )/SiO2 hybrid materials were tested as efficient and reusable heterogeneous catalysts for the synthesis of steroid derivatives, outperforming the bulk (Zr)UiO-66(NH2 ) MOF. A clear correlation between the catalytic activity of the dispersed Zr sites present in the confined MOF, and the loading of the mesoporous SiO2 , is demonstrated for steroid transformations.

Biofouling ecology as a means to better understand membrane biofouling.

Despite more than a decade of worldwide research on membrane fouling in membrane bioreactors, many questions remain to be answered. Biofouling, which is referred to as the unwanted deposition and growth of biofilms, remains the main problem. Due to its complexity, most of the existing anti-biofouling strategies are not completely successful. To unravel this complexity and finally to developed well-adapted control strategies, a microbial-based description of the biofouling development is needed. Therefore, in this review, the biofouling formation will be described as a typical biofilm formation in five steps including the formation of a conditioning film, the bacterial attachment, the production of extracellular polymeric substances, the biofilm maturation, and the bacterial detachment. Moreover, important processes such as hydrodynamics and bacterial communication or quorum sensing will be taken into account. It is finally discussed whether biofouling formation is an active or inactive biofilm process together with suggestion for further research.

Forward and pressure retarded osmosis: potential solutions for global challenges in energy and water supply.

Osmotically driven membrane processes (ODMP) have gained renewed interest in recent years and they might become a potential solution for the world's most challenging problems of water and energy scarcity. Though the concept of utilizing osmotic pressure difference between high and low salinity streams across semipermeable membranes has been explored for several decades, lack of optimal membranes and draw solutions hindered competition between forward osmosis (FO) and pressure retarded osmosis (PRO) with existing water purification and power generation technologies, respectively. Driven by growing global water scarcity and by energy cost and negative environmental impacts, novel membranes and draw solutions are being developed for ODMPs, mass and heat transfer in osmotic process are becoming better understood, and new applications of ODMPs are emerging. Therefore, OMDPs might become promising green technologies to provide clean water and clean energy from abundantly available renewable resources. This review focuses primarily on new insights into osmotic membrane transport mechanisms and on novel membranes and draw solutions that are currently being developed. Furthermore, the effects of operating conditions on the overall performance of osmotic membranes will be highlighted and future perspectives will be presented.

Designing sustainable membrane-based water treatment via fouling control through membrane interface engineering and process developments.

Membrane-based water treatment processes have been established as a powerful approach for clean water production. However, despite the significant advances made in terms of rejection and flux, provision of sustainable and energy-efficient water production is restricted by the inevitable issue of membrane fouling, known to be the major contributor to the elevated operating costs due to frequent chemical cleaning, increased transmembrane resistance, and deterioration of permeate flux. This review provides an overview of fouling control strategies in different membrane processes, such as microfiltration, ultrafiltration, membrane bioreactors, and desalination via reverse osmosis and forward osmosis. Insights into the recent advancements are discussed and efforts made in terms of membrane development, modules arrangement, process optimization, feed pretreatment, and fouling monitoring are highlighted to evaluate their overall impact in energy- and cost-effective water treatment. Major findings in four key aspects are presented, including membrane surface modification, modules design, process integration, and fouling monitoring. Among the above mentioned anti-fouling strategies, a large part of research has been focused on membrane surface modifications using a number of anti-fouling materials whereas much less research has been devoted to membrane module advancements and in-situ fouling monitoring and control. At the end, a critical analysis is provided for each anti-fouling strategy and a rationale framework is provided for design of efficient membranes and process for water treatment.

Stability of Filled PDMS Pervaporation Membranes in Bio-Ethanol Recovery from a Real Fermentation Broth.

Mixed matrix membranes (MMMs) have shown great potential in pervaporation (PV). As for many novel membrane materials however, lab-scale testing often involves synthetic feed solutions composed of mixed pure components, overlooking the possibly complex interactions and effects caused by the numerous other components in a real PV feed. This work studies the performance of MMMs with two different types of fillers, a core-shell material consisting of ZIF-8 coated on mesoporous silica and a hollow sphere of silicalite-1, in the PV of a real fermented wheat/hay straw hydrolysate broth for the production of bio-ethanol. All membranes, including a reference unfilled PDMS, show a declining permeability over time. Interestingly, the unfilled PDMS membrane maintains a stable separation factor, whereas the filled PDMS membranes rapidly lose selectivity to levels below that of the reference PDMS membrane. A membrane autopsy using XRD and SEM-EDX revealed an almost complete degradation of the crystalline ZIF-8 in the MMMs. Reference experiments with ZIF-8 nanoparticles in the fermentation broth demonstrated the influence of the broth on the ZIF-8 particles. However, the observed effects from the membrane autopsy could not exactly be replicated, likely due to distinct differences in conditions between the in-situ pervaporation process and the ex-situ reference experiments. These findings raise significant questions regarding the potential applicability of MOF-filled MMMs in real-feed pervaporation processes and, potentially, in harsh condition membrane separations in general. This study clearly confirms the importance of testing membranes in realistic conditions.

1H-1,2,4-Triazole as solvent for imidazolium methanesulfonate.

The solvation effect of 1H-1,2,4-triazole towards imidazolium methanesulfonate was studied by blending imidazolium methanesulfonate and 1H-1,2,4-triazole. Upon addition of 1H-1,2,4-triazole, the melting point of imidazolium methanesulfonate was lowered to less than 100 °C while maintaining the high ionic conductivity for a wide composition range of the blend. The ionic conductivity of the blend can be adequately described by using the Vogel-Fulcher-Tamman equation. A vehicle mechanism is postulated to govern the proton conduction for the blend. The contribution of protons to the ionic conductivity was corroborated electrochemically. The blend exhibited electrochemical activities for H(2) oxidation and O(2) reduction at a Pt electrode, as well as a wide electrochemical window. Therefore, suitable blends can possibly serve as electrolytes for polymer electrolyte membrane fuel cells operating under non-humidifying conditions. The solvation effect studied herein suggests a promising approach to a wider application area of protic ionic liquids.

Analysis of the microbial community structure in a membrane bioreactor during initial stages of filtration.

Membrane biofouling was investigated during the early stages of filtration in a laboratory-scale membrane bioreactor operated on molasses wastewater. The bacterial diversity and composition of the membrane biofilm and activated sludge were analyzed using terminal restriction fragment length polymorphism coupled with 16S rRNA clone library construction and sequencing. The amount of extracellular polymeric substances produced by bacteria was investigated using spectroscopic methods. The results reveal that the bacterial community of activated sludge differs significantly from that of the membrane biofilm, especially at the initial phase. Phylogenetic analysis based on 16S rRNA gene sequences identified 25 pioneer OTUs responsible for membrane surface colonization. Also, the relationship between the identified bacterial strains and the system specifications was explored.

MOF/Polymer Mixed-Matrix Membranes Preparation: Effect of Main Synthesis Parameters on CO2/CH4 Separation Performance.

Design and preparation of mixed-matrix membranes (MMMs) with minimum defects and high performance for desired gas separations is still challenging as it depends on a variety of MMM synthesis parameters. In this study, 6FDA-DAM:DABA based MMMs using MOF-808 as filler were prepared to examine the impact of multiple variables on the preparation process of MMMs, including variation in polymer concentration, filler loading, volume of solution cast per membrane area, solvent type used and solvent evaporation rate, and to identify their impact on the CO2/CH4 separation performance of these membranes. Solvent evaporation rate proved to be the most critical synthesis parameter, directly influencing the performance and visual appearance of the membranes. Although less dominantly influencing the MMM performance, polymer concentration and solution volume also had an important role via control over the casting solution viscosity, particle agglomeration, and particle settling rate. Among all solvents studied, MMMs prepared with chloroform led to the best performance for this polymer-filler system. Chloroform-based MMMs containing 10 and 30 wt.% MOF-808 showed 73% and 62% increase in CO2 permeability, respectively, without a decrease in separation factor compared to unfilled membranes. The results indicate that enhanced gas separation performance of MMMs strongly depends on the cumulative effect of various synthesis parameters rather than individual impact, thus requiring a system-specific design and optimization.

Membrane-based technologies for biogas separations.

Over the past two decades, membrane processes have gained a lot of attention for the separation of gases. They have been found to be very suitable for wide scale applications owing to their reasonable cost, good selectivity and easily engineered modules. This critical review primarily focuses on the various aspects of membrane processes related to the separation of biogas, more in specific CO(2) and H(2)S removal from CH(4) and H(2) streams. Considering the limitations of inorganic materials for membranes, the present review will only focus on work done with polymeric materials. An overview on the performance of commercial membranes and lab-made membranes highlighting the problems associated with their applications will be given first. The development studies carried out to enhance the performance of membranes for gas separation will be discussed in the subsequent section. This review has been broadly divided into three sections (i) performance of commercial polymeric membranes (ii) performance of lab-made polymeric membranes and (iii) performance of mixed matrix membranes (MMMs) for gas separations. It will include structural modifications at polymer level, polymer blending, as well as synthesis of mixed matrix membranes, for which addition of silane-coupling agents and selection of suitable fillers will receive special attention. Apart from an overview of the different membrane materials, the study will also highlight the effects of different operating conditions that eventually decide the performance and longevity of membrane applications in gas separations. The discussion will be largely restricted to the studies carried out on polyimide (PI), cellulose acetate (CA), polysulfone (PSf) and polydimethyl siloxane (PDMS) membranes, as these membrane materials have been most widely used for commercial applications. Finally, the most important strategies that would ensure new commercial applications will be discussed (156 references).

Combining patterned membrane filtration and flocculation for economical microalgae harvesting.

Membranes have a lot of potential for harvesting microalgae, but mainly membrane fouling and high harvesting costs linked to low fluxes are hampering their breakthrough. Patterned membranes can reduce fouling by enchancing local turbulences close to the membrane surface on one hand, and by increasing the active area per m2 of installed membrane on the other. Flocculation can further increase membrane permeance by increasing microalgal partical size and reducing the fraction of free organic matter in the feed. In current study, the effect of polyethylene glycol (PEG) in the casting solution of patterned polysulfone membranes was investigated to better tune the performance of the patterned membranes, together with the effects of cross-flow velocity and chitosan dosage on membrane fouling. The energy consumption and total harvesting cost, extrapolated to a full-scale microalgal harvesting, were then estimated. The patterned membrane prepared with a 28w% PEG concentration showed the highest clean water permeance (900±22 L/m2 h bar) and membrane permeance in a microalgal suspension (590±17 L/m2 h bar). Patterned membranes showed a lower filtration resistance (15% permeance decline at the end of filtration) than flat membranes (72%) at a cross-flow velocity of 0.0025 m/s. Increasing cross-flow velocity could increase membrane permeance in most cases. The highest stable membrane permeance (110±17 L/m2 h bar) and the lowest filtration resistance were achieved when combining patterned membrane filtration with flocculation at optimized chitosan dosage. A very low energy consumption (0.28 kWh/kg) and harvesting cost (0.16 €/kg) were achieved under these conditions.

γ-Valerolactone as Bio-Based Solvent for Nanofiltration Membrane Preparation.

γ-Valerolactone (GVL) was selected as a renewable green solvent to prepare membranes via the process of phase inversion. Water and ethanol were screened as sustainable non-solvents to prepare membranes for nanofiltration (NF). Scanning electron microscopy was applied to check the membrane morphology, while aqueous rose Bengal (RB) and magnesium sulphate (MgSO4) feed solutions were used to screen performance. Cellulose acetate (CA), polyimide (PI), cellulose triacetate (CTA), polyethersulfone (PES) and polysulfone (PSU) membranes were fine-tuned as materials for preparation of NF-membranes, either by selecting a suitable non-solvent for phase inversion or by increasing the polymer concentration in the casting solution. The best membranes were prepared with CTA in GVL using water as non-solvent: with increasing CTA concentration (10 wt% to 17.5 wt%) in the casting solution, permeance decreased from 15.9 to 5.5 L/m2·h·bar while RB rejection remained higher than 94%. The polymer solubilities in GVL were rationalized using Hansen solubility parameters, while membrane performances and morphologies were linked to viscosity measurements and cloudpoint determination of the casting solutions to better understand the kinetic and thermodynamic aspects of the phase inversion process.

Use of Ionic Liquids and Co-Solvents for Synthesis of Thin-Film Composite Membranes.

Polyamide (PA) thin-film composite (TFC) membranes are commonly applied in reversed osmosis (RO) and nanofiltration (NF) applications due to their thin, dense top-layer, and high selectivity. Recently, the conventional organic phase (i.e., hexane) during interfacial polymerization (IP) was replaced by less toxic ionic liquids (ILs) which led to excellent membrane performances. As the high price of most ILs limits their up-scaling, the potential use of inexpensive Aliquat was investigated in this study. The thin-film composite (TFC) membranes were optimized to remove flavor compounds, i.e., ethyl acetate (EA) and isoamyl acetate (IA), from a fermentation broth. A multi-parameter optimization was set-up involving type of support, reaction time for IP, water content of Aliquat, and concentration of both monomers m-phenylenediamine (MPD) and trimesoylchloride (TMC). The membranes prepared using Aliquat showed similar fluxes as those prepared from a reference IL 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([C4mpyr][Tf2N]) but with better EA and IA retentions, even better than for a commercial RO membrane (GEA type AF). Finally, the recently introduced epoxide-curing of Bisphenol A diglycidyl ether (BADGE) with 1,6-hexanediamine (HDA) was investigated using Aliquat as organic phase. It is the first time this type of IP was performed in combination with an IL as organic phase. The resulting membrane was used in the filtration of a 35 µM Rose Bengal (RB) in 20 wt% dimethylformamide/ water (DMF/H2O) feed mixture. A well-crosslinked poly(ß-alkanolamine) film was obtained with a > 97% retention.

Solvent-Resistant UV-Cured Polysulfone Support Membranes Using a Green Solvent.

Solvent-resistant UV-cured supports consisting of a semi-interpenetrating network of polysulfone (PSf) and cross-linked poly-acrylate were successfully synthesized for the first time using an alternative, non-reprotoxic, and biodegradable solvent. Tamisolve® NxG is a high-boiling, dipolar aprotic solvent with solubility parameters similar to those of dimethylformamide (DMF) and N-methyl-2-pyrrolidone (NMP), making it an eco-friendly alternative. The support membranes, prepared via UV-curing followed by non-solvent-induced phase inversion, can serve as a universal solvent-resistant support for the synthesis of a broad set of membranes, for which the selective layer can be deposited from any solvent. Parameters such as UV irradiation time and intensity, as well as the concentrations of PSf, penta-acrylate, and photo-initiator in the casting solution were varied to obtain such supports. The characteristics of the resulting supports were investigated in terms of separation performance, hydrophobicity, porosity, degree of acrylate conversion, and pure water flux. The resulting membranes showed improved chemical resistance in solvents such as ethyl acetate, NMP, tetrahydrofuran (THF), and toluene. Solvent-resistant supports with different pore sizes were synthesized and used for the preparation of thin film composite (TFC) membranes to demonstrate their potential. Promising separation performances with Rose Bengal (RB) rejections up to 98% and water permeances up to 1.5 L m-2 h-1 bar-1 were reached with these TFC-membranes carrying a polyamide top layer synthesized via interfacial polymerization.

Harvesting microalgal biomass using negatively charged polysulfone patterned membranes: Influence of pattern shapes and mechanism of fouling mitigation.

Membranes have a lot of potential for harvesting microalgae, but membrane fouling is hampering their breakthrough. In this study, the effects of charge and corrugated surface on membrane filtration performance were investigated. The clean water permeance (CWP), the microalgae harvesting efficiency and the membrane flux for a microalgal broth were determined using patterned polysulfone (PSf) membranes with different shapes of the surface patterns and containing different charge densities by blending sulfonated polysulfone (sPSf). The flow behavior near the patterned membrane surface, as well as the interaction energy between membrane and microalgae were investigated using computational fluid dynamics (CFD) simulation and the improved extended "Derjaguin, Landau, Verwey, Overbeek" (XDLVO) theory, respectively. Membrane charge and pattern shape significantly improve the membrane performance. The critical pressures of all sPSf blend patterned membranes were higher than 2.5 bar. A 4.5w% sPSf blend patterned membranes with wave patterns showed the highest CWP (2300 L/m2 h bar) and membrane flux in the microalgal broth (1000 L/m2 h bar) with 100% harvesting efficiency. XDLVO analysis showed that sPSf blend patterned membranes prepared obtained the lowest interaction energy and highest energy barrier for microalgal attachment. CFD simulation showed a higher velocity and wall shear on the pattern apexes.

Influence of ionic liquid-like cationic pendants composition in cellulose based polyelectrolytes on membrane-based CO2 separation.

Cellulose acetate (CA) is an attractive membrane polymer for CO2 capture market. However, its low CO2 permeability hampers its application as part of a membrane for most relevant types of CO2 containing feeds. This work investigates the enhancement of CA separation performance by incorporating ionic liquid-like pendants (1-methylimidazol, 1-methylpyrrolidine, and 2-hydroxyethyldimethylamine (HEDMA) on the CA backbone. These CA-based polyelectrolytes (PEs), synthesised by covalent grafting of cationic pendants with anion metathesis, were characterised by NMR, FTIR, DSC/TGA, and processed into thin-film composite membranes. The membrane performance in CO2/N2 mixed-gas permeation experiments shows a decrease in CO2 and N2 permeability and an initial decrease and then gradual increase in CO2/N2 selectivity with increasing HEDMA content. The amount of HEDMA attached to the CA backbone determines overall separation process in bifunctional PEs. This indicates that the hydroxy-substituted cationic pendants alter interactions between PEs network and permeating CO2 molecules, suggesting possibilities for further improvements.