Investigating rolling as mechanism for humeral fractures in non-ambulant infants: a preliminary finite element study.

AIM: To use personalised computed tomography (CT)-based finite element models to quantitatively investigate the likelihood of self-inflicted humeral fracture in non-ambulant infants secondary to rolling. MATERIALS AND METHODS: Three whole-body post-mortem CT examinations of children at the age of rolling (two 4-month-old and one 6-month-old) were used. The mechanical moment needed by each infant to perform a rolling manoeuvre was calculated and applied to the finite element model in order to simulate spontaneous rolling from the prone to the supine position. RESULTS: The maximum predicted strains were found to be substantially lower (with a difference of >80%) than the elastic limit of the bone. CONCLUSION: Results of this study challenge the plausibility of self-inflicted humeral fracture caused by rolling in non-ambulant infants and indicate that it is unlikely for a humeral fracture to result from this mechanism without the assistance of an external force.

Predicting bone strength from CT data: Clinical applications.

In this review we summarise over 15 years of research and development around the prediction of whole bones strength from Computed Tomography data, with particular reference to the prediction of the risk of hip fracture in osteoporotic patients. We briefly discuss the theoretical background, and then provide a summary of the laboratory and clinical validation of these modelling technologies. We then discuss the three current clinical applications: in clinical research, in clinical trials, and in clinical practice. On average the strength predicted with finite element models (QCT-FE) based on computed tomography is 7% more accurate that that predicted with areal bone mineral density from Dual X-ray Absorptiometry (DXA-aBMD), the current standard of care, both in term of laboratory validation on cadaver bones and in terms of stratification accuracy on clinical cohorts of fractured and non-fractured women. This improved accuracy makes QCT-FE superior to DXA-aBMD in clinical research and in clinical trials, where the its use can cut in half the number of patients to be enrolled to get the same statistical power. For routine clinical use to decide who to treat with antiresorptive drugs, QCT-FE is more accurate but less cost-effective than DXA-aBMD, at least when the decision is on first line treatment like bisphosphonates. But the ability to predict skeletal strength from medical imaging is now opening a number of other applications, for example in paediatrics and oncology.

Patient-specific finite element estimated femur strength as a predictor of the risk of hip fracture: the effect of methodological determinants.

UNLABELLED: A finite element modelling pipeline was adopted to predict femur strength in a retrospective cohort of 100 women. The effects of the imaging protocol and the meshing technique on the ability of the femur strength to classify the fracture and the control groups were analysed. INTRODUCTION: The clinical standard to estimate the risk of osteoporotic hip fracture is based on the areal bone mineral density (aBMD). A few retrospective studies have concluded that finite element (FE)-based femoral strength is a better classifier of fracture and control groups than the aBMD, while others could not find significant differences. We investigated the effect of the imaging protocol and of the FE modelling techniques on the discriminatory power of femoral strength. METHODS: A retrospective cohort of 100 post-menopausal women (50 with hip fracture, 50 controls) was examined. Each subject received a dual-energy absorptiometry (DXA) exam and a computed tomography (CT) scan of the proximal femur region. Each case was modelled a number of times, using different modelling pipelines, and the results were compared in terms of accuracy in discriminating the fracture and the control cases. The baseline pipeline involved local anatomical orientation and mesh morphing. Revised pipelines involved global anatomical orientation using a full-femur atlas registration and an optimised meshing algorithm. Minimum physiological (MPhyS) and pathological (MPatS) strengths were estimated for each subject. Area under the receiver operating characteristic (ROC) curve (AUC) was calculated to compare the ability of MPhyS, MPatS and aBMD to classify the control and the cases. RESULTS: Differences in the modelling protocol were found to considerably affect the accuracy of the FE predictors. For the most optimised protocol, logistic regression showed aBMDNeck, MPhyS and MPatS to be significantly associated with the facture status, with AUC of 0.75, 0.75 and 0.79, respectively. CONCLUSION: The study emphasized the necessity of modelling the whole femur anatomy to develop a robust FE-based tool for hip fracture risk assessment. FE-strength performed only slightly better than the aBMD in discriminating the fracture and control cases. Differences between the published studies can be explained in terms of differences in the modelling protocol and cohort design.

A multiscale orchestrated computational framework to reveal emergent phenomena in neuroblastoma.

Neuroblastoma is a complex and aggressive type of cancer that affects children. Current treatments involve a combination of surgery, chemotherapy, radiotherapy, and stem cell transplantation. However, treatment outcomes vary due to the heterogeneous nature of the disease. Computational models have been used to analyse data, simulate biological processes, and predict disease progression and treatment outcomes. While continuum cancer models capture the overall behaviour of tumours, and agent-based models represent the complex behaviour of individual cells, multiscale models represent interactions at different organisational levels, providing a more comprehensive understanding of the system. In 2018, the PRIMAGE consortium was formed to build a cloud-based decision support system for neuroblastoma, including a multi-scale model for patient-specific simulations of disease progression. In this work we have developed this multi-scale model that includes data such as patient's tumour geometry, cellularity, vascularization, genetics and type of chemotherapy treatment, and integrated it into an online platform that runs the simulations on a high-performance computation cluster using Onedata and Kubernetes technologies. This infrastructure will allow clinicians to optimise treatment regimens and reduce the number of costly and time-consuming clinical trials. This manuscript outlines the challenging framework's model architecture, data workflow, hypothesis, and resources employed in its development.

A comparison between micro-CT and histology for the evaluation of cortical bone: effect of polymethylmethacrylate embedding on structural parameters.

Cortical bone microstructure is an important parameter in the evaluation of bone strength. The aim of this study was to validate the characterization of human cortical bone microarchitecture using microcomputed tomography. In order to do this, microcomputed tomography structural measurements were compared with those obtained through histological examination (the gold standard). Moreover, to calculate structural parameters, microcomputed tomography images have to be binarized with the separation between bone and nonbone structures throughout a global thresholding. As the effect of the surrounding medium on the threshold value is not clear, an easy procedure to find the global uniform threshold for a given acquisition condition is applied. This work also compared the structural parameters of microcomputed tomography cortical sample scan in air or embedded in polymethylmethacrylate; histology was used as a reference. For each acquisition condition, a fixed threshold value was found and was applied on the corresponding microcomputed tomography image for the parameters assessment. Twenty cortical bone samples were collected from human femur and tibia diaphyses. All samples were microcomputed tomography scanned in air, embedded in polymethylmethacrylate, rescanned by microcomputed tomography, examined by histology and finally compared. A good correspondence between the microcomputed tomography images and the histological sections was found. Paired comparisons in cortical porosity, Haversian canal diameter and Haversian canal separation between histological sections and microcomputed tomography cross sections, first in air and then embedded in PolyMethylMethAcrylate, were made: no significant differences were found. None of the comparisons showed significant differences for cortical porosity, Haversian canal diameter and Haversian separation over a three-dimensional volume of interest, between microcomputed tomography scans in air and with samples embedded in PolyMethylMethAcrylate. The very good correlation between bone structural measures obtained from microcomputed tomography datasets and from two-dimensional histological sections confirms that microcomputed tomography may be an efficient tool for the characterization of cortical bone microstructure. Moreover, when the corresponding threshold value for each condition is used, structural parameters determined by microcomputed tomography are not affected by the surrounding medium (PolyMethylMethAcrylate).

Extensive risk analysis of mechanical failure for an epiphyseal hip prothesis: a combined numerical-experimental approach.

There has been recent renewed interest in proximal femur epiphyseal replacement as an alternative to conventional total hip replacement. In many branches of engineering, risk analysis has proved to be an efficient tool for avoiding premature failures of innovative devices. An extensive risk analysis procedure has been developed for epiphyseal hip prostheses and the predictions of this method have been compared to the known clinical outcomes of a well-established contemporary design, namely hip resurfacing devices. Clinical scenarios leading to revision (i.e. loosening, neck fracture and failure of the prosthetic component) were associated with potential failure modes (i.e. overload, fatigue, wear, fibrotic tissue differentiation and bone remodelling). Driving parameters of the corresponding failure mode were identified together with their safe thresholds. For each failure mode, a failure criterion was identified and studied under the most relevant physiological loading conditions. All failure modes were investigated with the most suitable investigation tool, either numerical or experimental. Results showed a low risk for each failure scenario either in the immediate postoperative period or in the long term. These findings are in agreement with those reported by the majority of clinical studies for correctly implanted devices. Although further work is needed to confirm the predictions of this method, it was concluded that the proposed risk analysis procedure has the potential to increase the efficacy of preclinical validation protocols for new epiphyseal replacement devices.

Delivering computationally-intensive digital patient applications to the clinic: An exemplar solution to predict femoral bone strength from CT data.

BACKGROUND AND OBJECTIVE: Whilst fragility hip fractures commonly affect elderly people, often causing permanent disability or death, they are rarely addressed in advance through preventive techniques. Quantification of bone strength can help to identify subjects at risk, thus reducing the incidence of fractures in the population. In recent years, researchers have shown that finite element models (FEMs) of the hip joint, derived from computed tomography (CT) images, can predict bone strength more accurately than other techniques currently used in the clinic. The specialised hardware and trained personnel required to perform such analyses, however, limits the widespread adoption of FEMs in clinical contexts. In this manuscript we present CT2S (Computed Tomography To Strength), a system developed in collaboration between The University of Sheffield and Sheffield Teaching Hospitals, designed to streamline access to this complex workflow for clinical end-users. METHODS: The system relies on XNAT and makes use of custom apps based on open source software. Available through a website, it allows doctors in the healthcare environment to benefit from FE based bone strength estimation without being exposed to the technical aspects, which are concealed behind a user-friendly interface. Clinicians request the analysis of CT scans of a patient through the website. Using XNAT functionality, the anonymised images are automatically transferred to the University research facility, where an operator processes them and estimates the bone strength through FEM using a combination of open source and commercial software. Following the analysis, the doctor is provided with the results in a structured report. RESULTS: The platform, currently available for research purposes, has been deployed and fully tested in Sheffield, UK. The entire analysis requires processing times ranging from 3.5 to 8 h, depending on the available computational power. CONCLUSIONS: The short processing time makes the system compatible with current clinical workflows. The use of open source software and the accurate description of the workflow given here facilitates the deployment in other centres.

Evaluation of patient tissue selection methods for deriving equivalent density calibration for femoral bone quantitative CT analyses.

Osteoporosis affects an increasing number of people every year and patient specific finite element analysis of the femur has been proposed to identify patients that could benefit from preventative treatment. The aim of this study was to demonstrate, verify, and validate an objective process for selecting tissues for use as the basis of phantomless calibration to enable patient specific finite element analysis derived hip fracture risk prediction. Retrospective reanalysis of patient computed tomography (CT) scans has the potential to yield insights into more accurate prediction of osteoporotic fracture. Bone mineral density (BMD) specific calibration scans are not typically captured during routine clinical practice. Tissue-based BMD calibration can therefore empower the retrospective study of patient CT scans captured during routine clinical practice. Together the method for selecting tissues as the basis for phantomless calibration coupled with the post-processing steps for deriving a calibration equation using the selected tissues provide an estimation of quantitative equivalent density results derived using calibration phantoms. Patient tissues from a retrospective cohort of 211 patients were evaluated. The best phantomless calibration resulted in a femoral strength (FS) [N] bias of 0.069 ± 0.07% over FS derived from inline calibration and a BMD [kg/cm3] bias of 0.038 ± 0.037% over BMD derived from inline calibration. The phantomless calibration slope for the best method presented was within the range of patient specific calibration curves available for comparison and demonstrated a small bias of 0.028 ± 0.054 HU/(mg/cm3), assuming the Mindways Model 3 BMD inline calibration phantom as the gold standard. The presented method of estimating a calibration equation from tissues showed promise for CT-based femoral fracture analyses of retrospective cohorts without readily available calibration data.

Quality control protocol for in vitro micro-computed tomography.

The aim of this work was to present and discuss a quality control protocol for in vitro micro-computed tomography (microCT), based on the adaptation of the quality control protocols for medical computed tomography. The importance of establishing a quality control protocol is related to the opportunity to identify problems on time comparing the microCT images acquired in different time points, and in this way to verify the performance of the device. The proposed quality control protocol was applied for a long-time monitoring period to verify the stability of the micro-tomographic system over time. The protocol proposed in this study was applied to the histomorphometric characterization of bone tissue, but it can be used on a wide range of in vitro microCT applications. Noise and uniformity tests, taken and adapted to micro-tomographic system by medical standard guidelines of quality control, were performed by the use of a water phantom. An accuracy test was designed and performed by the use of a morphometric calibrated phantom. All these tests were performed during a long-time monitoring period to control the stability of the system. Specific control charts and monitoring parameters for each test were used to represent the monthly measures collected during 20 months and an out of control condition was defined. The reference values (baseline), calculated to control the stability of micro-tomographic system over time, were calculated during acceptance/status test. During the period, no out of control conditions in noise, uniformity and accuracy tests were recorded. However, a changing condition was found in noise test, as showed by using statistical C (P < 0.01) and Kruskal-Wallis (P < 0.05) tests. In particular, a Wilcoxon rank sum test with Bonferroni correction (P < 0.0125) was applied in noise test to investigate which of the comparisons among first five acquisitions of year 2004 (group B.L.) and each group was significant (P < 0.0125). The noise showed a slight but significant increase over the years compared to baseline value; however, no out of control conditions were recorded. Nonetheless, a maintenance service to control the performance of mechanical components of microCT was required and performed.

Integrated friction measurements in hip wear simulations: short-term results.

Hip joint wear simulators are used extensively to simulate the dynamic behaviour of the human hip joint and, through the wear rate, gain a concrete indicator about the overall wear performance of different coupled bearings. Present knowledge of the dynamic behaviour of important concurrent indicators, such as the coefficient of friction, could prove helpful for the continuing improvement in applied biomaterials. A limited number of commercial or custom-made simulators have been designed specifically for friction studies but always separately from wear tests; thus, analysis of these two important parameters has remained unconnected. As a result, a new friction sensor has been designed, built, and integrated in a commercial biaxial rocking motion hip simulator. The aim of this study is to verify the feasibility of an experimental set-up in which the dynamic measurement of the friction factor could effectively be implemented in a standard wear test without compromising its general accuracy and repeatability. A short wear test was run with the new set-up for 1 x 10(6) cycles. In particular, three soft-bearings (metal-on-polyethylene, phi = 28 mm) were tested; during the whole test, axial load and frictional torque about the vertical loading axis were synchronously recorded in order to calculate the friction factor. Additional analyses were performed on the specimens, before and after the test, in order to verify the accuracy of the wear test. The average friction factor was 0.110 +/- 0.025. The friction sensors showed good accuracy and repeatability throughout. This innovative set-up was able to reproduce stable and reliable measurements. The results obtained encourage further investigations of this set-up for long-term assessment and using different combinations of materials.

Effect of long-term physiological activity on the long-term stem stability of cemented hip arthroplasty: in vitro comparison of three commercial bone cements.

Long-term endurance of the cement mantle is fundamental for the survival of cemented hip prostheses. Current protocols to characterize bone cements are unsuitable to predict the actual clinical outcome. The aim of this study was to assess if it is possible to rank cement types having diverse clinical outcome by using a simplified in vitro physiological test. Composite femurs were implanted with identical stems (Lubinus-SPII), using different commercial cement types: CMW1 to represent cement with poor clinical outcome; Simplex-P and Cemex-RX to represent cements with a positive clinical outcome. Implanted femurs were subjected to a validated protocol that simulated a demanding but physiological loading spectrum. Inducible micromotions and permanent migrations were recorded throughout the test. After test completion, the cement mantles were sectioned and inspected with dye penetrants to quantify the fatigue-induced cracks. Micromotions did not differ significantly between cement types (possibly because a successful prosthesis was chosen that is very stable in the host bone). Significant differences were observed in terms of cement cracks: CMW1 induced significantly more numerous and larger cracks than Simplex-P and Cemex-RX; no difference was observed between Simplex-P and Cemex-RX. This indicates that this protocol: (a) can discriminate between 'good' and 'bad' cements and (b) yields consistent results when comparable cements are tested. The proposed protocol overcomes the limitations of existing standardized material tests for bone cements. New cements can be assessed in comparison with other cements with known (positive/negative) clinical outcome, tested with the same protocol.

Effect of size and location of simulated lytic lesions on the structural properties of human vertebral bodies, a micro-finite element study.

Currently, the Spinal Instability Neoplastic Score system is used in clinics to evaluate the risk of fracture in patients with spinal metastases. This method, however, does not always provide a clear guideline due to the complexity in accounting for the effect of metastatic lesions on vertebral stability. The aim of this study was to use a validated micro Finite Element (microFE) modelling approach to analyse the effect of the size and location of lytic metastases on the mechanical properties of human vertebral bodies. Micro Computed Tomography based microFE models were generated with and without lytic lesions simulated as holes within a human vertebral body. Single and multiple lytic lesions were simulated with four different sizes and in five different locations. Bone was assumed homogenous, isotropic and linear elastic, and each vertebra was loaded in axial compression. It was observed that the size of lytic lesions was linearly related with the reduction in structural properties of the vertebral body (reduction of stiffness between 3% and 30% for lesion volume between 4% and 35%). The location of lytic lesions did not show a clear effect on predicted structural properties. Single or multiple lesions with the same volume provided similar results. Locally, there was a homogeneous distribution of axial principal strains among the models with and without lytic lesions. This study highlights the potential of microFE models to study the effect of lesions on the mechanical properties of the human vertebral body.

Microindentation on cortical human bone: effects of tissue condition and indentation location on hardness values.

The hardness of cortical human bone has been measured on osteons in different conditions. However, no data are reported in the literature regarding the effect of cortical tissue condition and indentation location on the measured hardness values. This study aimed to investigate whether the hardness of the human cortical bone evaluated by micro-indentation is influenced, first, by the tissue condition and, second, by the distance of the indentation from the edge of the Haversian canal. Two femura were collected from a subject without musculoskeletal disease. The Vickers hardness was measured by means of microindentation (applied load, 100 gf) on osteons with a cross-section greater than 200 microm. The tests were performed on wet and embedded tissue at different distances from the Haversian canal edge (30-150 microm). No significant differences were found in hardness values between the two contralateral femura. Embedded tissue was significantly harder (12 per cent) than wet tissue. No significant differences were found in hardness values measured at different distances from the Haversian canal edge except for those closer than 60 microm. Therefore, indentations cannot be performed on osteons small in cross-section, since the distance from the closer pore has to be controlled. They should be performed on wet tissue, to avoid an offset in the measured hardness.

Strain distribution in the proximal human femoral metaphysis.

There is significant interest in the stress-strain state in the proximal femoral metaphysis, because of its relevance for hip fractures and prosthetic replacements. The scope of this work was to provide a better understanding of the strain distribution, and of its correlation with the different directions of loading, and with bone quality. A total of 12 pairs of human femurs were instrumented with strain gauges. Six loading configurations were designed to cover the range of directions spanned by the hip joint force. Inter-specimen variability was reduced if paired specimens were considered. The principal strain magnitude varied greatly between loading configurations. This suggests that different loading configurations need to be simulated in vitro. The strain magnitude varied between locations but, on average, was compatible with the strain values measured in vivo. The strain magnitudes and the direction of principal tensile strain in the head and neck were compatible with the spontaneous fractures of the proximal femur reported in some subjects. The principal tensile strain was significantly larger where the cortical bone was thinner; the compressive strain was larger where the cortical bone was thicker. The direction of the principal strain varied significantly between measurement locations but varied little between loading configurations. This suggests that the anatomy and the distribution of anisotropic material properties enable the proximal femur to respond adequately to the changing direction of daily loading.

Effect of stem preheating on the fatigue behaviour of bone cement around hip prostheses.

Tensile fatigue behaviour of bone cement specimens obtained from cement mantles moulded in vitro, simulating the surgical scenario, was investigated. The effect of stem preheating, before its insertion into the cement dough, on specimen fatigue life was studied. A commercial bone cement was selected for this study. Bone cement mixing was conducted in air, following the manufacturer's instructions, and injected simulating the clinical practice. Two conditions were considered: stem maintained at the surgical room temperature (23 degrees C), and stem preheated to 45 degrees C. Four repetitions of the whole procedure were performed for each condition obtaining a total of 32 specimens. All specimens underwent fatigue testing (stress ratio, 0; maximum tensile stress, 15 MPa) until failure. Both two-parameter and three-parameter Weibull distributions were initially used to analyse the fatigue life data set. However, the two-parameter distribution was chosen for both groups on the basis of the coefficient of determination used to test the goodness of fit. Stem preheating seems to have a negligible effect on fatigue behaviour of the studied bone cement in the low range of fatigue lives (up to 10(4)). However, above this number of cycles, stem preheating seems to reduce the probability of failure. These findings are discussed in the text.

Stress shielding and stress concentration of contemporary epiphyseal hip prostheses.

After the first early failures, proximal femoral epiphyseal replacement is becoming popular again. Prosthesis-to-bone load transfer is critical for two reasons: stress shielding is suspected of being responsible for a number of failures of early epiphyseal prostheses; stress concentration is probably responsible of the relevant number of early femoral neck fractures in resurfaced patients. The scope of this work was to experimentally investigate the load transfer of a commercial epiphyseal prosthesis (Birmingham Hip Replacement (BHR)) and an innovative prototype proximal epiphyseal replacement. To investigate bone surface strain, ten cadaveric femurs were instrumented with 15 triaxial strain gauges. In addition the cement layer of the prototype was instrumented with embedded gauges to estimate the strain in the adjacent trabecular bone. Six different loading configurations were investigated, with and without muscles. For the BHR prosthesis, significant stress shielding was observed on the posterior side of the head-neck region (the strain was halved); a pronounced stress concentration was observed on the anterior surface (up to five times in some specimens); BHR was quite sensitive to the different loading configurations. For the prototype, the largest stress shielding was observed in the neck region (lower than the BHR; alteration less than 20 per cent); some stress concentration was observed at the head region, close to the rim of the prosthesis (alteration less than 20 per cent); the different loading configurations had similar effects. Such large alterations with respect to the pre-operative conditions were found only in regions where the strain level was low. Conversely, alterations were moderate where the strain was higher. Thus, prosthesis-to-bone load transfer of both devices has been elucidated; the prototype preserved a stress distribution closer to the physiological condition.

Biomechanical assessment of vertebrae with lytic metastases with subject-specific finite element models.

The assessment of risk of vertebral fracture in patients with lytic metastases is challenging, due to the complexity in modelling the mechanical properties of this heterogeneous material. Currently clinical assessment of patients at high risk of fracture is based on the Spinal Instability Neoplastic Score (SINS), which however in many cases does not provide clear guidelines. The goal of this study was to develop a computational approach to provide a comparative biomechanical assessment of vertebrae with lytic lesions with respect to the adjacent controls and highlight the critical vertebrae. The computed tomography images of the thoracolumbar spine of eight patients suffering of vertebral lytic metastases with SINS between 7 and 12 (indeterminate unstable) were analysed. For each patient one or two vertebrae with lytic lesions were modelled and the closest vertebrae without lesions were considered as control. Metastatic vertebrae (N = 12) and controls (N = 18) were converted to subject-specific, heterogeneous, isotropic, nonlinear finite element models for simulating uniaxial compression. Densitometric and mechanical properties were computed for each vertebra. In average, similar mechanical properties were found for vertebrae with lytic lesions and controls (e.g. ultimate force equal to 6.2 ±â€¯2.7 kN for vertebrae with lytic lesions and to 6.2 ±â€¯3.0 kN for control vertebrae). Only in three patients the vertebrae with lytic lesions were found to be mechanically weaker (-19% to -75% difference for ultimate stress) than the controls. In conclusion, in this study we presented an approach to estimate the mechanical competence of vertebrae with lytic metastases. It remains to be investigated in a clinical study if this method, together with the SINS, can better classify patients with vertebrae with lytic lesions at high risk of fracture.

Unicompartmental knee prostheses: in vitro wear assessment of the menisci tibial insert after two different fixation methods.

Knee osteoarthritis is a complex clinical scenario where many biological and mechanical factors influence the severity of articular degenerative changes. Minimally invasive knee prosthetic surgery, with only a compartment replacement (unicompartmental knee replacement), might be a good compromise between osteotomy and total knee prosthesis. The focus of this study was to develop and validate a protocol to assess the fixation method of the femoral components in mechanical simulation, for pre-clinical validation; the wear behaviour of two different fixation frames was quantified and compared. In particular, two different wear tests were conducted using the same knee simulator, the same load profiles and the same kinematics; two different fixation methods were applied to the femoral sleds (synthetic femur and metal block). Surface characterization on both articulating bearings was performed by a roughness measuring machine and coordinate measuring machine. The wear produced by the tibial inserts using the synthetic femur was considerably higher than the wear registered by the metal-block holder. Roughness measurements on femoral sleds showed a limited number of scratches with high R(t) values for the metal-block set-up; the damaged surface broadened in the case of femoral condyles and tibial inserts mounted on composite bone, but lower R(t) and linear penetration values were measured. The two holding frames showed different wear activities as a consequence of dissimilar dynamic performance. Further observations should be made in vivo to prove the actual importance of synthetic bone simulations and specific material behaviour.

Dependence of mechanical compressive strength on local variations in microarchitecture in cancellous bone of proximal human femur.

Human cancellous bone is a heterogeneous material. Despite this, most of the published studies report correlations between mechanical properties and morphometric parameters averaged on the whole specimen. This work investigated whether local variations in morphometric parameters were linked to the localized failure regions of cancellous bone. Additionally, it was examined whether local values of morphometric parameters can predict the ultimate stress better than the average bone volume fraction (BV/TV). Cylindrical cancellous bone specimens extracted along the primary compressive group of human femoral heads were studied. These were microCT-imaged to assess the morphometric parameters, compressed to determine the ultimate stress, and rescanned by microCT to visualize the failure region. Failure involved slightly less than half of the free height of the specimens. Significant differences were found in the morphometric parameters calculated in the failure and in the non-failure regions. The cross-sections containing minimum BV/TV values were those most often located inside the failure region (83%, p<0.001). Regression analysis confirmed that variations in BV/TV best describe variations in ultimate stress (R2=0.84) out of the averaged morphometric parameters. The prediction of ultimate stress increased when minimum or maximum values of the morphometric parameters were taken, with the highest prediction found by considering the minimum BV/TV (R2=0.95). In conclusion, due to the heterogeneity of cancellous bone, there may exist regions characterized by a different microarchitecture, where the bone is weaker and consequently is more likely to fail. These regions mostly contain minimum values in BV/TV, which were found to predict ultimate stress better than average BV/TV.

Tribology and total hip joint replacement: current concepts in mechanical simulation.

Interest in the rheology and effects of interacting surfaces is as ancient as man. This subject can be represented by a recently coined word: tribology. This term is derived from the Greek word "tribos" and means the "science of rubbing". Friction, lubrication, and wear mechanism in the common English language means the precise field of interest of tribology. Wear of total hip prosthesis is a significant clinical problem that involves, nowadays, a too high a number of patients. In order to acquire further knowledge on the tribological phenomena that involve hip prosthesis wear tests are conducted on employed materials to extend lifetime of orthopaedic implants. The most basic type of test device is the material wear machine, however, a more advanced one may more accurately reproduce some of the in vivo conditions. Typically, these apparatus are called simulators, and, while there is no absolute definition of a joint simulator, its description as a mechanical rig used to test a joint replacement, under conditions approximating those occurring in the human body, is acceptable. Simulator tests, moreover, can be used to conduct accelerated protocols that replicate/simulate particularly extreme conditions, thus establishing the limits of performance for the material. Simulators vary in their level of sophistication and the international literature reveals many interpretations of the design of machines used for joint replacement testing. This paper aims to review the current state of the art of the hip joint simulators worldwide. This is specified through a schematic overview by describing, in particular, constructive solutions adopted to reproduce in vivo conditions. An exhaustive commentary on the evolution and actually existing simulation standards is proposed by the authors. The need of a shared protocol among research laboratories all over the world could lead to a consensus conference.