Interrogation of 3d Transition Bimetallic Nanocrystal Nucleation and Growth Using In Situ Electron Microscope and Synchrotron X-ray Techniques.

Understanding the nucleation and growth mechanism of 3d transition bimetallic nanocrystals (NCs) is crucial to developing NCs with tailored nanostructures and properties. However, it remains a significant challenge due to the complexity of 3d bimetallic NCs formation and their sensitivity to oxygen. Here, by combining in situ electron microscopy and synchrotron X-ray techniques, we elucidate the nucleation and growth pathways of Fe-Ni NCs. Interestingly, the formation of Fe-Ni NCs emerges from the assimilation of Fe into Ni clusters together with the reduction of Fe-Ni oxides. Subsequently, these NCs undergo solid-state phase transitions, resulting in two distinct solid solutions, ultimately dominated by γ-Fe3Ni2. Furthermore, we deconvolve the interplays between local coordination and electronic state concerning the growth temperature. We directly visualize the oxidation-state distributions of Fe and Ni at the nanoscale and investigate their changes. This work may reshape and enhance the understanding of nucleation and growth in atomic crystallization.

A pH-Sensitive Stretchable Zwitterionic Hydrogel with Bipolar Thermoelectricity.

Amid growing interest in using body heat for electricity in wearables, creating stretchable devices poses a major challenge. Herein, a hydrogel composed of two core constituents, namely the negatively-charged 2-acrylamido-2-methylpropanesulfonic acid and the zwitterionic (ZI) sulfobetaine acrylamide, is engineered into a double-network hydrogel. This results in a significant enhancement in mechanical properties, with tensile stress and strain of up to 470.3 kPa and 106.6%, respectively. Moreover, the ZI nature of the polymer enables the fabrication of a device with polar thermoelectric properties by modulating the pH. Thus, the ionic Seebeck coefficient (Si) of the ZI hydrogel ranges from -32.6 to 31.7 mV K-1 as the pH is varied from 1 to 14, giving substantial figure of merit (ZTi) values of 3.8 and 3.6, respectively. Moreover, a prototype stretchable ionic thermoelectric supercapacitor incorporating the ZI hydrogel exhibits notable power densities of 1.8 and 0.9 mW m-2 at pH 1 and 14, respectively. Thus, the present work paves the way for the utilization of pH-sensitive, stretchable ZI hydrogels for thermoelectric applications, with a specific focus on harvesting low-grade waste heat within the temperature range of 25-40 °C.

Exploring Pyrazine-Based Organic Redox Couples for Enhanced Thermoelectric Performance in Wearable Energy Harvesters.

Thermoelectric generators (TEGs) based on thermogalvanic cells can convert low-temperature waste heat into electricity. Organic redox couples are well-suited for wearable devices due to their nontoxicity and the potential to enhance the ionic Seebeck coefficient through functional-group modifications.  Pyrazine-based organic redox couples with different functional groups is comparatively analyzed through cyclic voltammetry under varying temperatures. The results reveal substantial differences in entropy changes with temperature and highlight 2,5-pyrazinedicarboxylic acid dihydrate (PDCA) as the optimal candidate. How the functional groups of the pyrazine compounds impact the ionic Seebeck coefficient is examined, by calculating the electrostatic potential based on density functional theory. To evaluate the thermoelectric properties, PDCA is integrated in different concentrations into a double-network hydrogel comprising poly(vinyl alcohol) and polyacrylamide. The resulting champion device exhibits an impressive ionic Seebeck coefficient (Si) of 2.99 mV K-1, with ionic and thermal conductivities of ≈67.6 µS cm-1 and ≈0.49 W m-1 K-1, respectively. Finally, a TEG is constructed by connecting 36 pieces of 20 × 10-3 m PDCA-soaked hydrogel in series. It achieves a maximum power output of ≈0.28 µW under a temperature gradient of 28.3 °C and can power a small light-emitting diode. These findings highlight the significant potential of TEGs for wearable devices.

Decomposition of methanol-d4 on Rh nanoclusters supported by thin-film Al2O3/NiAl(100) under near-ambient-pressure conditions.

The decomposition of methanol-d4 (CD3OD) on Rh nanoclusters grown by the deposition of Rh vapors onto an ordered thin film of Al2O3/NiAl(100) was studied, with various surface-probe techniques and largely under near-ambient-pressure (NAP) conditions. The results showed a superior reactivity of small Rh clusters (diameter < 1.5 nm) exposed to CD3OD at 5 × 10-3-0.1 mbar at 400 K; the gaseous production of CO and D2 from decomposed methanol-d4 per Rh surface site on the small Rh clusters with diameters of ∼1.1 nm was nearly 8 times that on large ones with diameters of ∼3.5 nm. The promotion of reactivity with decreased cluster size under NAP conditions was evidently greater than that under ultrahigh vacuum conditions. Moreover, the concentration of atomic carbon (C*; where * denotes adsorbate)-a key catalyst poisoner-yielded from the dissociation of CO* from dehydrogenated methanol-d4 was significantly smaller on small clusters (diameter < 1.5 nm). The NAP size effect on methanol-d4 decomposition involved the surface hydroxyl (OH*) from the little co-adsorbed water (H2O*) that was dissociated at a probability dependent on the cluster size. H2O* was more likely dissociated into OH* on small Rh clusters, by virtue of their more reactive d-band structure, and the OH* then effectively promoted the O-D cleavage of methanol-d4, as the rate-determining step, and thus the reaction probability; on the other hand, the OH* limited CO* dissociation on small Rh clusters via both adsorbate and lateral effects. These results suggest that the superior properties of small Rh clusters in both reactivity and anti-poisoning would persist and be highly applicable under "real-world" catalysis conditions.

A single-atom library for guided monometallic and concentration-complex multimetallic designs.

Atomically dispersed single-atom catalysts have the potential to bridge heterogeneous and homogeneous catalysis. Dozens of single-atom catalysts have been developed, and they exhibit notable catalytic activity and selectivity that are not achievable on metal surfaces. Although promising, there is limited knowledge about the boundaries for the monometallic single-atom phase space, not to mention multimetallic phase spaces. Here, single-atom catalysts based on 37 monometallic elements are synthesized using a dissolution-and-carbonization method, characterized and analysed to build the largest reported library of single-atom catalysts. In conjunction with in situ studies, we uncover unified principles on the oxidation state, coordination number, bond length, coordination element and metal loading of single atoms to guide the design of single-atom catalysts with atomically dispersed atoms anchored on N-doped carbon. We utilize the library to open up complex multimetallic phase spaces for single-atom catalysts and demonstrate that there is no fundamental limit on using single-atom anchor sites as structural units to assemble concentration-complex single-atom catalyst materials with up to 12 different elements. Our work offers a single-atom library spanning from monometallic to concentration-complex multimetallic materials for the rational design of single-atom catalysts.

Decomposition of methanol-d4 on a thin film of Al2O3/NiAl(100) under near-ambient-pressure conditions.

We have studied the decomposition of methanol-d4 on thin film Al2O3/NiAl(100) under near-ambient-pressure conditions, with varied surface-probe techniques and calculations based on density-functional theory. Methanol-d4 neither adsorbed nor reacted on Al2O3/NiAl(100) at 400 K under ultrahigh vacuum conditions, whereas they dehydrogenated, largely to methoxy-d3 (CD3O*, * denoting adsorbates) and formaldehyde-d2 (CD2O*), on the surface when the methanol-d4 partial pressure was increased to 10-3 mbar and above. The dehydrogenation was facilitated by hydroxyl (OH* or OD*) from the dissociation of little co-adsorbed water; a small fraction of CD2O* interacted further with OH* (OD*) to form, via intermediate CD2OOH* (CD2OOD*), formic acid (DCOOH* or DCOOD*). A few surface carbonates were also yielded, likely on the defect sites of Al2O3/NiAl(100). The results suggest that alumina not only supports metal clusters but also participates in reactions under realistic catalytic conditions. One may consider accordingly the multiple functions of alumina while designing ideal catalysts.

Efficient H2 Evolution Coupled with Anodic Oxidation of Iodide over Defective Carbon-Supported Single-Atom Mo-N4 Electrocatalyst.

We successfully prepared nitrogen-doped defective carbon spheres (Mo-N4/d-C) with a high loading of 0.996 wt % via a designed vapor-deposition process for IOR-based hydrogen generation. The synthesized Mo-N4/d-C catalyst provides a record current density of 10 mA cm-2 at 0.77 V. Further, the Mo-N4/d-C catalyst shows a Tafel slope of 25.58 mV dec-1, exceptional stability over time in acidic media, a higher hydrogen generation rate of 0.1063 mL gcat-1 min-1, a high Faradaic efficiency of 99.8%, and a reduction of the energy consumption up to ∼50% for hydrogen evolution by anodic oxidation reaction of iodide (IOR) compared with the conventional OER-based electrolysis. Computational calculations demonstrate that the Mo-N4/d-C structure plays a vital effect on the activity of iodide oxidation, which is competitive with the Pt catalyst.

Dual-Axis Alignment of Bulk Artificial Water Channels by Directional Water-Induced Self-Assembly.

Approaching single-crystal-like morphology has always been important in driving materials toward their optimal properties. With only orientational order, liquid crystal (LC) materials require dual-axis orientational control to optimize their structural order in the bulk phase. However, current external guiding fields such as electrical, magnetic, and mechanical guiding fields are less effective in aligning amphiphilic LCs. In this study, water is developed as an excellent structural stabilizer and orientation-directing agent of an amphiphilic discotic molecule (AD) in the water-induced self-assembly (WISA) process. Thermal analysis and structural characterization results show that water increases the stability and domain sizes of the hexagonal columnar (Colh) phase of the AD by co-assembling with the ADs to form bulk artificial water channels (AWCs). Moreover, through control over the nucleation conditions (degree of supercooling and location of nucleation), dual-axis alignment in both the planar and vertical growth of the AWCs is achieved by applying water as the guiding field in the directional WISA. With precise control over the hierarchical structures, the bulk AWC array of the AD delivers excellent salt rejection properties and water permeability. Considering that all the amphiphilic LCs have hydrophilic segments, these new roles of water in the WISA process could launch the further development of functional amphiphilic LCs by providing a dynamic interaction and a readily available guiding field.

Solar to hydrocarbon production using metal-free water-soluble bulk heterojunction of conducting polymer nanoparticle and graphene oxide.

This work demonstrates the first example of interfacial manipulation in a hybrid photocatalyst based on poly(3-hexylthiophene-2,5-diyl) (P3HT) nanoparticle and graphene oxide (GO) bulk heterojunctions to efficiently reduce CO2 into selective industrial hydrocarbons under gas-phase reaction and visible-light illumination. High selectivity of chemical products (methanol and acetaldehyde) was observed. Moreover, the hybrid photocatalyst's solar-to-fuel conversion efficiency was 13.5 times higher than that of pure GO. The increased production yield stems from the co-catalytic and sensitizing role of P3HT in the hybrid system due to its ability to extend light absorption to the visible range and improve interfacial charge transfer to GO. The hybrid P3HT-GO formed a type II heterojunction, and its static and dynamic exciton behaviors were examined using fluorescence spectroscopy and exciton lifetime mapping. A reduced fluorescence decay time was observed by interfacial manipulation for improved dispersion, indicating a more efficient charge transfer from the excited P3HT to GO. Thus, the conducting polymer nanoparticles, 2D nanocarbon, have demonstrated superior performance as a metal-free, non-toxic, low-cost, and scalable heterogeneous photocatalyst for CO2 reduction to solar fuel, a solid-gas system.

Interfacial Interaction of Absorbate Copper Phthalocyanine with PVDF Based Ferroelectric Polymer Substrates: A Spectroscopic Study.

Studies of CuPc thin films on underlying ferroelectric copolymeric and terpolymeric substrates have been performed by ultraviolet photoelectron spectroscopy (UPS), X-ray photoelectron spectroscopy (XPS), and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. Work function (WF) and highest occupied molecular orbital (HOMO) energy level shift observed from UPS spectroscopy for successive deposition of CuPc molecules on ferroelectric polymer surfaces confirm the formation of interface dipole at the CuPc-ferroelectric polymer interface owing to charge transfer from the tailing region of the CuPc HOMO density of states (DOS) to the ferroelectric polymer layer. According to our thickness dependent XPS data, CuPc molecules are coupled to the organic ferroelectric surfaces through the central metal atom of the CuPc molecules, i.e., copper atom, and the halogens of underlying ferroelectric polymer surfaces, and hence support the charge transfer phenomenon from CuPc molecules to the ferroelectric polymer substrate. Polarization dependent NEXAFS results reveal that CuPc molecules retain their tilted geometrical configuration even at submonolayer thickness of the molecular films on both ferroelectric surfaces and confirms the electronic structural disturbance associated with structural modification of CuPc molecules due to interfacial charge transfer. Therefore, the energy level alignment with increment in the thickness of CuPc films at both the organic semiconductor-ferroelectric polymer interface is controlled by the charge transfer phenomenon from deposited CuPc molecules to the organic ferroelectric substrates. Our results provide a clear understanding about chemical interactions, molecular configurations, energy level alignment, and their correlation at CuPc/polymeric ferroelectric interfaces that can be important for organic nonvolatile memory and synaptic based thin-film transistor devices.

n-Alkanethiols Directly Grown on a Bare Si(111) Surface: From Disordered to Ordered Transition.

We observed the growth phase transition of n-alkanethiols (AT), CH3(CH2)n-1SH, n = 4-16, directly implanted on a bare Si(111) surface, forming an AT monolayer. These monolayers were characterized with static water-contact angle, high-resolution X-ray photoelectron spectroscopy, near-edge X-ray fine-structure spectroscopy, and grazing-angle reflection absorption Fourier-transform infrared spectroscopy. The integrated spectral results indicated that the implanted n-AT molecules formed a self-oriented and densely packed monolayer through formation of an S-Si bond. With the number of carbons in the alkyl chain at six or more, namely beginning at hexanethiol, the molecular monolayer began to develop an orientation-ordered structure, which is clearly shorter than that for AT monolayers on Au and Ag. This result implies that, with a stronger molecule-substrate interaction, an ordered molecular monolayer can form with a short chain.

High-Magnesium Calcite Mesocrystals: Formation in Aqueous Solution under Ambient Conditions.

Mesocrystals of high-magnesian calcites are commonly found in biogenic calcites. Under ambient conditions, it remains challenging to prepare mesocrystals of high-magnesian calcite in aqueous solution. We report that mesocrystals of calcite with magnesium content of about 20 mol % can be obtained from the phase transformation of magnesian amorphous calcium carbonate (Mg-ACC) in lipid solution. The limited water content on the Mg-ACC surface would reduce the extent of the dissolution-reprecipitation process and bias the phase transformation pathway toward solid-state reaction. We infer from the selected area electron diffraction patterns and the dark-field transmission electron microscopic images that the formation of Mg-calcite mesocrystals occurs through solid-state secondary nucleation, for which the phase transformation is initiated near the mineral surface and the crystalline phase propagates gradually toward the interior part of the microspheres of Mg-ACC.

Interface properties between a low band gap conjugated polymer and a calcium metal electrode.

Interfaces between metal electrodes and π-conjugated polymers play an important role in the organic optoelectronic devices. In this paper, the molecular orientation of the pristine poly[(9,9-dioctylfluorenyl-2,7-diyl)-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (APFO3) films, chemical reactions and the electronic structure during the interface formation of Ca/APFO3 have been investigated in detail using synchrotron radiation photoemission spectroscopy (SRPES), X-ray photoemission spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. It is shown that the APFO3 film has a high degree of orientational ordering with its aromatic ring tilted at an angle of 43° from the substrate, and the 9,9-dioctyl fluorene unit (F8) is almost in the same plane as the benzothiazole unit (BT). Upon vapor-deposition of Ca onto APFO3 at room temperature, Ca dopes electrons into APFO3 and induces the downward band bending of APFO3. Moreover, Ca can diffuse into the APFO3 subsurface and react with N, S and C atoms of APFO3. Finally, the barrier of electron injection at the Ca/APFO3 interface is derived by the energy level alignment diagram. These results enable us to gain comprehensive insights into APFO3 and will facilitate the reasonable design of high performance devices based on APFO3.

A direct Fe-O coordination at the FePc/MoO(x) interface investigated by XPS and NEXAFS spectroscopies.

Molecule-substrate interaction plays a vital role in determining the electronic structures and charge transfer properties in organic-transition metal oxides (TMOs) hybridized devices. In this work, the interactions at the FePc/MoO3 interface has been investigated in detail by using synchrotron radiation photoemission spectroscopy (SRPES) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. Compared with the annealing of the bare MoO3 film, the FePc adsorption is found to promote the thermal reduction of the underlying MoO3 film. XPS and NEXAFS experimental results unanimously demonstrate a strong electronic coupling between FePc molecules and the MoOx (x < 3) substrate. A direct Fe-O coordination at the interface as well as an electron transfer from the molecules toward the substrate is proposed. This strong coupling is compatible with a facile electron transfer from FePc molecules toward electrode through a MoOx interlayer. The understanding of the molecule-substrate interaction at the atomic level is of significance in engineering functionalized surfaces with potential applications in nanoscience, molecular electronics and photonics.

The first heteropentanuclear extended metal-atom chain: [Ni⁺-Ru25⁺-Ni²âº-Ni²âº (tripyridyldiamido)4(NCS)2].

This study develops the first heteropentametal extended metal atom chain (EMAC) in which a string of nickel cores is incorporated with a diruthenium unit to tune the molecular properties. Spectroscopic, crystallographic, and magnetic characterizations show the formation of a fully delocalized Ru2(5+) unit. This [Ru2]-containing EMAC exhibits single-molecule conductance four-fold superior to that of the pentanickel complex and results in features of negative differential resistance (NDR), which are unobserved in analogues of pentanickel and pentaruthenium EMACs. A plausible mechanism for the NDR behavior is proposed for this diruthenium-modulated EMAC.

Growth Behavior of Ni on Hydrogen-Etched WS2 Surface.

Transition metal dichalcogenides (TMDs) are 2D materials in which the layers are stacked together by van der Waals forces. Although TMDs are expected to be promising for electronic applications, forming a uniform electrode on them is challenging because of the low adhesion forces between metals and TMDs. This study focuses on improving the quality of metal electrodes by introducing atomic H to create surface defects, using Ni on WS2 as an example. The detailed effects of H etching and subsequent Ni growth were investigated using scanning tunneling microscopy (STM) and synchrotron-based X-ray photoemission (XPS) techniques. Our studies reveal that introducing point defects of ∼3.05 × 1011 cm-2 on the WS2 surface, results in a significant shift in Ni growth from the Volmer-Weber to a near Frank-van der Merwe mode. The origin of the change is the bond formation between the Ni and W atoms, which is expected to realize ohmic contact. The optimization of metal-TMD interfaces offers valuable insights for advanced applications.

Li-Sb Alloy Formation Strategy to Improve Interfacial Stability of All-Solid-State Lithium Batteries.

The solid electrolyte is anticipated to prevent lithium dendrite formation. However, preventing interface reactions and the development of undesirable lithium metal deposition during cycling are difficult and remain unresolved. Here, to comprehend these occurrences better, this study reports an alloy formation strategy for enhanced interface stability by incorporating antimony (Sb) in the lithium argyrodite solid electrolyte Li6PS5Cl (LPSC-P) to form Li-Sb alloy. The Li-Sb alloy emergence at the anodic interface is crucial in facilitating uniform lithium deposition, resulting in excellent long-term stability, and achieving the highest critical current density of 14.5 mA cm-2 (among the reported sulfide solid electrolytes) without lithium dendrite penetration. Furthermore, Li-Sb alloy formation maintain interfacial contact, even, after several plating and stripping. The Li-Sb alloy formation is confirmed by XRD, Raman, and XPS. The work demonstrates the prospect of utilizing alloy-forming electrolytes for advanced solid-state batteries.

Boosting the Interfacial Stability of the Li6PS5Cl Electrolyte with a Li Anode via In Situ Formation of a LiF-Rich SEI Layer and a Ductile Sulfide Composite Solid Electrolyte.

Due to its good mechanical properties and high ionic conductivity, the sulfide-type solid electrolyte (SE) can potentially realize all-solid-state batteries (ASSBs). Nevertheless, challenges, including limited electrochemical stability, insufficient solid-solid contact with the electrode, and reactivity with lithium, must be addressed. These challenges contribute to dendrite growth and electrolyte reduction. Herein, a straightforward and solvent-free method was devised to generate a robust artificial interphase between lithium metal and a SE. It is achieved through the incorporation of a composite electrolyte composed of Li6PS5Cl (LPSC), polyethylene glycol (PEG), and lithium bis(fluorosulfonyl)imide (LiFSI), resulting in the in situ creation of a LiF-rich interfacial layer. This interphase effectively mitigates electrolyte reduction and promotes lithium-ion diffusion. Interestingly, including PEG as an additive increases mechanical strength by enhancing adhesion between sulfide particles and improves the physical contact between the LPSC SE and the lithium anode by enhancing the ductility of the LPSC SE. Moreover, it acts as a protective barrier, preventing direct contact between the SE and the Li anode, thereby inhibiting electrolyte decomposition and reducing the electronic conductivity of the composite SE, thus mitigating the dendrite growth. The Li|Li symmetric cells demonstrated remarkable cycling stability, maintaining consistent performance for over 3000 h at a current density of 0.1 mA cm-2, and the critical current density of the composite solid electrolyte (CSE) reaches 4.75 mA cm-2. Moreover, the all-solid-state lithium metal battery (ASSLMB) cell with the CSEs exhibits remarkable cycling stability and rate performance. This study highlights the synergistic combination of the in-situ-generated artificial SE interphase layer and CSEs, enabling high-performance ASSLMBs.

Investigating the role of undercoordinated Pt sites at the surface of layered PtTe2 for methanol decomposition.

Transition metal dichalcogenides, by virtue of their two-dimensional structures, could provide the largest active surface for reactions with minimal materials consumed, which has long been pursued in the design of ideal catalysts. Nevertheless, their structurally perfect basal planes are typically inert; their surface defects, such as under-coordinated atoms at the surfaces or edges, can instead serve as catalytically active centers. Here we show a reaction probability > 90 % for adsorbed methanol (CH3OH) on under-coordinated Pt sites at surface Te vacancies, produced with Ar+ bombardment, on layered PtTe2 - approximately 60 % of the methanol decompose to surface intermediates CHxO (x = 2, 3) and 35 % to CHx (x = 1, 2), and an ultimate production of gaseous molecular hydrogen, methane, water and formaldehyde. The characteristic reactivity is attributed to both the triangular positioning and varied degrees of oxidation of the under-coordinated Pt at Te vacancies.

Crystalline growth of rubrene film enhanced by vertical ordering in cadmium arachidate multilayer substrate.

The growth of highly crystalline rubrene thin films for organic field effect transistor (OFET) application remains a challenge. Here, we report on the vapor-deposited growth of rubrene films on the substrates made of cadmium arachidate (CdA) multilayers deposited onto SiO2/Si(100) via the Langmuir-Blodgett technique. The CdA films, containing 2n+1 layers, with integer n ranging from 0 to 4, are surface-terminated identically by the methyl group but exhibit the thickness-dependent morphology. The morphology and structure of both CdA and rubrene films are characterized by X-ray reflectivity (XRR), X-ray diffraction (XRD), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, and atomic force microscopy (AFM). Crystalline rubrene films, evidenced by XRD and marked by platelet features in AFM images, become observable when grown onto the CdA layer thicker than 5L. XRD data show that vertical ordering, that is, ordering along surface normal, of CdA multilayer substrates exerts a strong influence in promoting the crystalline growth of rubrene films. This promoted growth is not due to the surface energy of CdA layer but derived from the additional interaction localized between rubrene and CdA island sidewall and presumably strengthened by a close dimensional match between the a-axis of rubrene lattice and the layer spacing of CdA multilayer. The best OFET mobility is recorded for 9L CdA substrate and reaches 6.7 × 10(-2) cm(2) V(-1) s(-1), presumably limited by the roughness of the interface between CdA and rubrene films.