RESUMO
Hydrogen storage for energy applications is of significant interest to researchers seeking to enable a transition to lower-pollution energy systems. Two of the key drawbacks of using hydrogen for energy storage are the low gas-phase storage density and the high energy cost of the gas-phase compression. Metal hydride materials have the potential to increase hydrogen storage density and decrease the energy cost of compression by storing the hydrogen as a solid solution. In this article, the technical viability of core-shell V90Al10-Pd80Ag20 as a hydrogen storage material is discussed. LaNi5, LaNi5/acrylonitrile-butadiene-styrene copolymer mixtures, core-shell V-Pd, and core-shell V90Al10-Pd80Ag20 are directly compared in terms of reversible hydrogen-storage content by weight and volume. The kinetic information for each of the materials is also compared; however, this work highlights missing information that would enable computational dynamics modelling. Results of this technical evaluation show that V90Al10-Pd80Ag20 has the potential to increase gravimetric and volumetric hydrogen capacity by 1.4 times compared to LaNi5/acrylonitrile-butadiene-styrene copolymer mixtures. In addition, the literature shows that Pd80Ag20 and V90Al10 both have similarly good hydrogen permeabilities, thermal conductivities, and specific heats. In summary, this evaluation demonstrates that core-shell V90Al10-Pd80Ag20 could be an excellent, less-expensive hydrogen storage material with the advantages of improved storage capacity, handleability, and safety compared to current AB5-polymer mixtures.
RESUMO
The critical component of a proton exchange membrane fuel cell (PEMFC) system is the proton exchange membrane (PEM). Perfluorosulfonic acid membranes such as Nafion are currently used for PEMFCs in industry, despite suffering from reduced proton conductivity due to dehydration at higher temperatures. However, operating at temperatures below 100 °C leads to cathode flooding, catalyst poisoning by CO, and complex system design with higher cost. Research has concentrated on the membrane material and on preparation methods to achieve high proton conductivity, thermal, mechanical and chemical stability, low fuel crossover and lower cost at high temperatures. Non-fluorinated polymers are a promising alternative. However, improving the efficiency at higher temperatures has necessitated modifications and the inclusion of inorganic materials in a polymer matrix to form a composite membrane can be an approach to reach the target performance, while still reducing costs. This review focuses on recent research in composite PEMs based on non-fluorinated polymers. Various inorganic fillers incorporated in the PEM structure are reviewed in terms of their properties and the effect on PEM fuel cell performance. The most reliable polymers and fillers with potential for high temperature proton exchange membranes (HTPEMs) are also discussed.
RESUMO
Mixed-matrix membranes containing synthesised nano-sized zeolite 4A and PVAc were fabricated to investigate the effect of zeolite loading on membrane morphology, polymer-filler interaction, thermal stability and gas separation properties. SEM studies revealed that, although the membranes with 40â wt % nano-sized zeolite particles were distributed uniformly through the polymer matrix without voids, the membranes with 15â wt % zeolite loading showed agglomeration. With increasing zeolite content, the thermal stability improved, the permeability decreased and the selectivity increased. The effect of silanation on dispersion of 15â wt % zeolite 4A nanoparticles through PVAc was investigated by post-synthesis modification of the zeolite with 3-Aminopropyl(diethoxy)methylsilane. Modification of the nanoparticles improved their dispersion in PVAc, resulting in higher thermal stability than the corresponding unmodified zeolite membrane. Modification also decreased the rigidity of the membrane. Partial pore blockage of the modified zeolite nanoparticles after silanation caused a further decrease in permeability, compared to the 15â wt % unmodified zeolite membrane.
RESUMO
Reversible hydrogen storage capacity of the La(3-x)Mg(x)Ni(9) alloys, charged by gaseous hydrogen or by electrochemical methods, reaches its maximum at composition La(2)MgNi(9). As (La,Mg)Ni(3-3.5) alloys are the materials used in advanced metal hydride electrodes in Ni-MH batteries, this raises interest in the study of the structure-properties interrelation in the system La(2)MgNi(9)-H(2) (D(2)). In the present work, this system has been investigated by use of in situ synchrotron X-ray and neutron powder diffraction in H(2)/D(2) gas and by performing pressure-composition-temperature measurements. The saturated La(2)MgNi(9)D(13.1) hydride forms via an isotropic expansion and crystallizes with a trigonal unit cell (space group R3m (No.166); a = 5.4151(1) Å; c = 26.584(2) Å; V = 675.10(6) Å(3)). The studied hybrid structure is composed of a stacking of two layers resembling existing intermetallic compounds LaNi(5) (CaCu(5) type) and LaMgNi(4) (Laves type). These are occupied by D to form LaNi(5)D(5.2) and LaMgNi(4)D(7.9). The LaNi(5)D(5.2) slab has a typical structure observed for all reported LaNi(5)-containing hybrid structures of the AB(5) + Laves phase types. However, the Laves type slab LaMgNi(4)D(7.9) is different from the characterized individual LaMgNi(4)D(4.85) hydride. This results from the filling of a greater variety of interstitial sites in the La(2)MgNi(9)D(13)/LaMgNi(4)D(7.9), including MgNi(2), Ni(4), (La/Mg)(2)Ni(2), and (La/Mg)Ni(3), in contrast with individual LaMgNi(4)D(4.85) where only La(2)MgNi(2) and Ni(4) interstitials are occupied. Despite a random distribution of La and Mg in the structure, a local hydrogen ordering takes place with H atoms favoring occupation of two Mg-surrounded sites, triangles MgNi(2) and tetrahedra LaMgNi(2). A directional bonding between Ni, Mg, and hydrogen is observed and is manifested by a formation of the NiH(4) tetrahedra and MgH(6) octahedra, which are connected to each other by sharing H vertexes to form a spatial framework.
RESUMO
This paper describes new sample cells and techniques for in situ powder X-ray diffraction specifically designed for gas absorption studies up to ca 300â bar (1â bar = 100â 000â Pa) gas pressure. The cells are for multipurpose use, in particular the study of solid-gas reactions in dosing or flow mode, but can also handle samples involved in solid-liquid-gas studies. The sample can be loaded into a single-crystal sapphire (Al(2)O(3)) capillary, or a quartz (SiO(2)) capillary closed at one end. The advantages of a sapphire single-crystal cell with regard to rapid pressure cycling are discussed, and burst pressures are calculated and measured to be â¼300â bar. An alternative and simpler cell based on a thin-walled silicate or quartz glass capillary, connected to a gas source via a VCR fitting, enables studies up to â¼100â bar. Advantages of the two cell types are compared and their applications are illustrated by case studies.