Enzymatic Activity and Its Relationships with the Total Phenolic Content and Color Change in the High Hydrostatic Pressure-Assisted Curing of Vanilla Bean (Vanilla planifolia).

Diverse enzymatic reactions taking place after the killing of green vanilla beans are involved in the flavor and color development of the cured beans. The effects of high hydrostatic pressure (HHP) at 50-400 MPa/5 min and blanching as vanilla killing methods were evaluated on the total phenolic content (TPC), polyphenoloxidase (PPO), and peroxidase (POD) activity and the color change at different curing cycles of sweating-drying (C0-C20) of vanilla beans. The rate constants describing the above parameters during the curing cycles were also obtained. The TPC increased from C1 to C6 compared with the untreated green beans after which it started to decrease. The 400 MPa samples showed the highest rate of phenolic increase. Immediately after the killing (C0), the highest increase in PPO activity was observed at 50 MPa (46%), whereas for POD it was at 400 MPa (25%). Both enzymes showed the maximum activity at C1, after which the activity started to decrease. As expected, the L* color parameter decreased during the entire curing for all treatments. An inverse relationship between the rate of TPC decrease and enzymatic activity loss was found, but the relationship with L* was unclear. HHP appears to be an alternative vanilla killing method; nevertheless, more studies are needed to establish its clear advantages over blanching.

Effect of Ultrasound-Assisted Extraction of Carotenoids from Papaya (Carica papaya L. cv. Sweet Mary) Using Vegetable Oils.

By-products from fruits and are of great interest for their potential use in the food industry due to their high content of bioactive compounds. Herein, we examined the ultrasound-assisted extraction (UAE) of carotenoid and carotenoid esters from papaya pulp and peel using soybean oil and sunflower oil as alternative green solvents. Response surface methodology (RSM) was established to optimize the UAE process. Three independent variables, ultrasonic amplitude (20-60%), time (10-60 min), and co-solvent percentage (ethanol) (5-20%, v/v), were applied. The highest total carotenoid content in the UAE extracts was obtained from papaya pulp extracts (58.7 ± 1.6 and 56.0 ± 1.5 µg carotenoids/g oil) using soybean oil and sunflower oil, respectively (60% amplitude/ 10 min/ 20% ethanol). On the other hand, the highest carotenoid content (52.0 ± 0.9 µg carotenoids/g oil) was obtained from papaya peel using soybean oil applying the UAE process (20% amplitude/ 77 min/ 20% ethanol); a minor content of 39.3 ± 0.5 µg carotenoids/g oil was obtained from papaya peel using sunflower oil at 60% amplitude/ 60 min/ 5% ethanol. Lycopene was the most abundant carotenoid among all individual carotenoids observed in papaya oil extracts, obtaining the highest yields of this carotenoid when papaya pulp and peel were extracted using soybean oil (94% and 81%, respectively) and sunflower oil (95% and 82%, respectively). Great extraction of xanthophyll esters was detected using 20% of ethanol in the vegetable oil extraction solvent (v/v). High correlations (>0.85) was obtained between total carotenoid content and color determination in the UAE oil extracts. UAE vegetable oil extracts enriched with carotenoids from papaya by-products could be useful to formulate new food ingredients based on emulsions with interesting potential health benefits.

High Hydrostatic Pressure to Increase the Biosynthesis and Extraction of Phenolic Compounds in Food: A Review.

Phenolic compounds from fruits and vegetables have shown antioxidant, anticancer, anti-inflammatory, among other beneficial properties for human health. All these benefits have motivated multiple studies about preserving, extracting, and even increasing the concentration of these compounds in foods. A diverse group of vegetable products treated with High Hydrostatic Pressure (HHP) at different pressure and time have shown higher phenolic content than their untreated counterparts. The increments have been associated with an improvement in their extraction from cellular tissues and even with the activation of the biosynthetic pathway for their production. The application of HHP from 500 to 600 MPa, has been shown to cause cell wall disruption facilitating the release of phenolic compounds from cell compartments. HPP treatments ranging from 15 to 100 MPa during 10-20 min at room temperature have produced changes in phenolic biosynthesis with increments up to 155%. This review analyzes the use of HHP as a method to increase the phenolic content in vegetable systems. Phenolic content changes are associated with either an immediate stress response, with a consequent improvement in their extraction from cellular tissues, or a late stress response that activates the biosynthetic pathways of phenolics in plants.

Microscopical Evaluation of the Effects of High-Pressure Processing on Milk Casein Micelles.

The effect of different high-pressure processing (HPP) treatments on casein micelles was analyzed through scanning electron microscopy (SEM) and a particle size distribution analysis. Raw whole and skim milk samples were subjected to HPP treatments at 400, 500 and 600 MPa for Come-Up Times (CUT) up to 15 min at ambient temperature. Three different phenomena were observed in the casein micelles: fragmentation, alterations to shape and agglomeration. The particle size distribution analysis determined that, as pressure and time treatment increased, the three phenomena intensified. First, the size of the casein micelles began to decrease as their fragmentation occurred. Subsequently, the casein micelles lost roundness, and their shape deformed. Finally, in the most intense treatments (higher pressures and/or longer times), the micelles fragments began to agglomerate, which resulted in an increase in their average diameter. Homogenization and defatting had no significant effect on the casein micelles; however, the presence of fat in whole milk samples was bioprotective, as the effects of the three phenomena appeared faster in treated skim milk samples. Through this study, it was concluded that the size and structure of casein micelles are greatly altered during high-pressure treatment. These results provide information that broadens the understanding of the changes induced on casein micelles by high-pressure treatments at room temperature.

Effect of high hydrostatic pressures on microorganisms, total phenolic content and enzyme activity of mamey (Pouteria sapota) nectar.

Mamey (Pouteria sapota) is a Mexican native fruit of sweet flavor and high content of antioxidants. Some of these antioxidants are  sensitive to high temperatures. Nonthermal technologies such as high hydrostatic pressures (HHP) could be an adequate alternative to traditional thermal pasteurization. Mamey nectars were treated under different HHP conditions and the effects on native microorganisms (mesophilic bacteria, molds and yeast), pectinmethylesterase (PME) and polyphenoloxidase (PPO) activities as well as on total phenolic content (TPC), were evaluated. Most HHP treatments conditions were equally effective to inactive native microorganisms. The application of HHP improved the extraction of TPC showing increments of 24% (400 MPa/2 min) to 64% (500 MPa/2 min) compared with the control samples. At 500 MPa/5 and 10 min maximum inactivation levels of PPO of about 40% were obtained, while PME activity showed decrements up to 70% at 400 MPa/5 min. HHP showed to be a potential technology to preserve mamey nectar, but more conditions should be tested to reach higher enzyme inactivation.

Bioaccessibility of Antioxidants in Prickly Pear Fruits Treated with High Hydrostatic Pressure: An Application for Healthier Foods.

High hydrostatic pressure (HHP) is a commercial processing technology which can enhance the health potential of foods by improving the bioaccessibility of their bioactive compounds. Our aim was to study the bioaccessibility and digestive stability of phenolic compounds and betalains in prickly pear fruits (Opuntia ficus-indica L. Mill. var. Pelota and Sanguinos) treated with HHP (100, 350, and 600 MPa; come-up time and 5 min). The effects of HHP on pulps (edible fraction) and peels (sources of potential healthy ingredients) were assessed. In pulps, betanin bioaccessibility increased (+47% to +64%) when treated at 350 MPa/5 min. In HHP-treated pulps, increases in the bioaccessibility of piscidic acid (+67% to +176%) and 4-hydroxybenzoic acid glycoside (+126% to 136%) were also observed. Isorhamnetin glycosides in peels treated at 600 MPa/CUT had higher bioaccessibility (+17% to +126%) than their controls. The effects of HHP on the bioaccessibility of health-promoting compounds are not exclusively governed by extractability increases of antioxidants in the food matrix (direct effects). In this work we found evidence that indirect effects (effects on the food matrix) could also play a role in the increased bioaccessibility of antioxidants in fruits treated with HHP.

Phenolic Compounds in Mesoamerican Fruits-Characterization, Health Potential and Processing with Innovative Technologies.

Diets rich in phenolic compounds have been associated to reducing the risk of metabolic syndrome and its derived disorders. Fruits are healthy components of the human diet because of their vitamin, mineral, fiber and phenolic profile. However, they have a short shelf-life which is limited by microbiological growth and enzymatic activity. Innovative preservation methods such as high hydrostatic pressure, pulsed electric fields, ultrasound, microwave, cold plasma and ultraviolet light have become popular for the processing of fruits because they can preserve nutritional quality. In this review, the phenolic profile and health potential of 38 Mesoamerican fruits were assessed. Phenolic compounds were classified based on their contribution to the diet as flavonoids, phenolic acids, tannin, lignins and stilbenoids. Due to this composition, fruits showed a wide range of bioactivities which included anti-inflammatory, anti-diabetic, anti-hypertensive and anti-obesity activities, among others. Phenolic content in fruits submitted to innovative food processing technologies depended on parameters such as enzymatic activity, antioxidant capacity, microstructure integrity and cell viability. Innovative technologies could increase phenolic content while assuring microbiological safety by (i) promoting the release of bound phenolic compounds during processing and (ii) inducing the synthesis of phenolic compounds by activation of phenylpropanoid pathway during storage.

Wounding and UVB Light Synergistically Induce the Biosynthesis of Phenolic Compounds and Ascorbic Acid in Red Prickly Pears (Opuntia ficus-indica cv. Rojo Vigor).

The present study evaluated the effects of ultraviolet B (UVB) radiation and wounding stress, applied alone or combined, on the biosynthesis of phenolic compounds and ascorbic acid in the peel and pulp of red prickly pear (Opuntia ficus-indica cv. Rojo Vigor). Whole and wounded-fruit samples were treated with UVB radiation (6.4 W·m-2) for 0 and 15 min, and stored for 24 h at 16 °C. Phytochemical analyses were performed separately in the peel and pulp. The highest phenolic accumulation occurred after storage of the whole tissue treated with UVB, where the main phenolic compounds accumulated in the peel and pulp were quercetin, sinapic acid, kaempferol, rosmarinic acid, and sinapoyl malate, showing increases of 709.8%, 570.2%, 442.8%, 439.9%, and 186.2%, respectively, as compared with the control before storage. Phenylalanine ammonia-lyase (PAL) activity was increased after storage of the whole and wounded tissue treated with UVB light, and this increase in PAL activity was associated to phenolic accumulation. On the other hand, l-galactono-γ-lactone dehydrogenase (GalLDH) activity and ascorbic acid biosynthesis was enhanced due to UVB radiation, and the effect was increased when UVB was applied in the wounded tissue showing 125.1% and 94.1% higher vitamin C content after storage when compared with the control. Respiration rate was increased due to wounding stress, whereas ethylene production was increased by wounding and UVB radiation in prickly pears. Results allowed the generation of a physiological model explaining the UVB and wound-induced accumulation of phenolic compounds and ascorbic acid in prickly pears, where wounding facilitates UVB to access the underlying tissue and enhances an apparent synergistic response.

In Vitro Fecal Fermentation of High Pressure-Treated Fruit Peels Used as Dietary Fiber Sources.

Fruit by-products are being investigated as non-conventional alternative sources of dietary fiber (DF). High hydrostatic pressure (HHP) treatments have been used to modify DF content as well as its technological and physiological functionality. Orange, mango and prickly pear peels untreated (OU, MU and PPU) and HHP-treated at 600 MPa (OP/55 °C and 20 min, MP/22 °C and 10 min, PPP/55 °C and 10 min) were evaluated. Untreated and treated fruit peels were subjected to fecal in vitro fermentations. The neutral sugar composition and linkage glycosidic positions were related to the production of short chain fatty acids (SCFA) resulting from the fermentation of the materials. After HHP-treatments, changes from multibranched sugars to linear sugars were observed. After 24 h of fermentation, OP yielded the highest amount of SCFA followed by PPU and MP (389.4, 282.0 and 204.6 µmol/10 mg DF, respectively). HHP treatment increased the SCFA concentration of orange and mango peel by 7 and 10.3% respectively, compared with the untreated samples after 24 h of fermentation. The results presented herein suggest that fruit peels could be used as good fermentable fiber sources, because they yielded high amounts of SCFA during in vitro fermentations.

Inhibitory potential of prickly pears and their isolated bioactives against digestive enzymes linked to type 2 diabetes and inflammatory response.

BACKGROUND: Prickly pears are potential candidates for the development of low-cost functional foods because they grow with low water requirements in arid regions of the world. They are sources of betalains and phenolic compounds, which have been reported to contribute to human health. The study of the biological activity of different varieties and of their isolated bioactive constitutes is fundamental in the design of functional foods. In this context, our objective is the assessment of the ability of Spanish and Mexican prickly-pear cultivars to inhibit enzymes related to type 2 diabetes and the inflammatory response, and the contribution of their bioactive compounds to their nutra-pharmaceutical potential. RESULTS: Prickly pear peels presented the highest antioxidant activity due to their high isorhamnetin glycoside content. Isorhamnetin glycosides showed significantly higher antioxidant and anti-inflammatory activity than aglycone, particularly isorhamnetin glucosyl-rhamnosyl-pentoside (IG2), which also reported antihyperglycemic activity. Morada, Vigor, and Sanguinos whole fruits exhibited moderate α-amylase inhibition and higher α-glucosidase inhibition, which is ideal for lowering glucose absorption in hyperglycemia management. Sanguinos peels presented the highest anti-inflammatory activity because of their high indicaxanthin content and isorhamnetin glycoside profile. CONCLUSIONS: In the design of prickly pear functional foods, technological processing should prioritize the retention or concentration of these bioactive compounds to preserve (or increase) their natural antioxidant, antihyperglycemic and anti-inflammatory activity. Peels of red and orange varieties should be further evaluated for antioxidant and anti-inflammatory purposes while whole fruits of red and purple varieties could be considered possible candidates for hyperglycemia management. © 2019 Society of Chemical Industry.

State-of-the-Art Extraction Methodologies for Bioactive Compounds from Algal Biome to Meet Bio-Economy Challenges and Opportunities.

Over the years, significant research efforts have been made to extract bioactive compounds by applying different methodologies for various applications. For instance, the use of bioactive compounds in several commercial sectors such as biomedical, pharmaceutical, cosmeceutical, nutraceutical and chemical industries, has promoted the need of the most suitable and standardized methods to extract these bioactive constituents in a sophisticated and cost-effective manner. In practice, several conventional extraction methods have numerous limitations, e.g., lower efficacy, high energy cost, low yield, etc., thus urges for new state-of-the-art extraction methodologies. Thus, the optimization along with the integration of efficient pretreatment strategies followed by traditional extraction and purification processes, have been the primary goal of current research and development studies. Among different sources, algal biome has been found as a promising and feasible source to extract a broader spectrum of bioactive compounds with point-of-care application potentialities. As evident from the literature, algal bio-products includes biofuels, lipids, polyunsaturated fatty acids, pigments, enzymes, polysaccharides, and proteins. The recovery of products from algal biomass is a matter of constant development and progress. This review covers recent advancements in the extraction methodologies such as enzyme-assisted extraction (EAE), supercritical-fluid extraction (SFE), microwave-assisted extraction (MAE) and pressurized-liquid extraction (PLF) along with their working mechanism for extracting bioactive compounds from algal-based sources to meet bio-economy challenges and opportunities. A particular focus has been given to design characteristics, performance evaluation, and point-of-care applications of different bioactive compounds of microalgae. The previous and recent studies on the anticancer, antibacterial, and antiviral potentialities of algal-based bioactive compounds have also been discussed with particular reference to the mechanism underlying the effects of these active constituents with the related pathways. Towards the end, the information is also given on the possible research gaps, future perspectives and concluding remarks.

In vitro bioaccessibility of individual carotenoids from persimmon (Diospyros kaki, cv. Rojo Brillante) used as an ingredient in a model dairy food.

BACKGROUND: Addition of persimmon fruit, which is highly rich in carotenoids, to dairy products represents an alternative to obtain functional foods. However, carotenoid bioaccessibility is strongly influenced by fat content and food composition. That is why in vitro bioaccessibility of individual carotenoids was evaluated in persimmon-based dairy products formulated with whole (3.6% fat) or skimmed milk (0.25% fat) and different freeze-dried persimmon tissues. RESULTS: Unambiguous identification of seven xanthophylls (neoxanthin, violaxanthin, antheraxanthin, lutein, zeaxanthin, lutein epoxide and ß-cryptoxanthin) and three hydrocarbon carotenes (α-carotene, ß-carotene and lycopene) was achieved using high-performance liquid chromatography with a reverse-phase C-30 column. Total carotenoid content declined up 71% through the digestion process. In vitro bioaccessibility of carotenoids was significantly higher in dairy products formulated with whole milk than those with skimmed milk, representing a difference of more than 21% (in the formulation using persimmon whole fruit as ingredient). Furthermore, addition of whole milk to any type of persimmon tissue significantly improved the bioaccessibility of total provitamin A carotenoids, reaching the highest values (38%) with whole fruit and whole milk. CONCLUSION: The higher fat content in whole milk exerted a significant influence on carotenoid bioaccessibility, especially when using freeze-dried persimmon whole fruit. © 2017 Society of Chemical Industry.

Hygroscopic properties and glass transition of dehydrated mango, apple and banana.

An undesirable crispiness loss occurs when some dry fruits reach a critical moisture content (Xc ) and their glass transition temperature (Tg ) matches the storage temperature. Models for sorption isotherms and onset Tg values for dry mango, apple, and banana were used to estimate Xc values at 25 and 32 °C. All models yielded R2 > 0.97 but information theory criteria strongly supported GAB in all but one case (40 °C, mango). The Gordon-Taylor Tg model (GT) yielded high R2 values for apple and banana but resulted in R2 = 0.834 for mango. As moisture approached zero, mango Tg estimates displayed a downward concavity contrasting with a rapidly increasing trend for apple and banana. The Khalloufi-Maslouhi-Ratti (KMR) model for Tg as a function of aw showed a linear behavior. Although the KMR model fitted data with R2 > 0.996, it requires more parameters and when aw approached 0, estimated Tg values increased at a slower rate than for the GT model. In the case of banana and mango, both models predicted approximately the same Xc at 25 °C but not at 32 °C. Finally, all Xc values estimated based on Tg were lower than the monolayer values obtained with the GAB (apple and banana) and BET (mango) models. These results indicate that the glass transition induced by moisture uptake dominates the quality degradation of these dry fruits.

Inactivation model and risk-analysis design for apple juice processing by high-pressure CO2.

Sigmoidal microbial survival curves are observed in high-pressure carbon dioxide (HPCD) pasteurization treatments. The objectives of this study were to use the Gompertz primary model to describe the inactivation in apple juice of the pathogen Escherichia coli CGMCC1.90 and to apply probabilistic engineering to select HPCD treatments meeting at least 5 log10 reductions (SV ≥ 5) at 95% confidence. This required secondary models for the temperature (T, °C) and pressure (P, MPa) dependence of the Gompertz model parameters. The expressions [Formula: see text] and [Formula: see text] selected using goodness-of-fit measures and assessments based on Akaike and Bayesian information criteria were consistent with proposed mechanistic models for HPCD bactericidal effects. Monte Carlo simulations accounting for the variability and uncertainty of the parameter b and c estimates were used to predict SV values for a given time, temperature and CO2 pressure combination and desired confidence boundary. A similar approach used to estimate process times meeting SV ≥ 5 at 95% confidence for a given temperature and CO2 pressure combination, showed that HPCD processes met this requirement only for relatively long processing times, i.e., 35-124 min in the experimental range of 32-42 °C and 10-30 MPa. Therefore, further HPCD research is required to reduce processing time.

Using high hydrostatic pressures to retain the antioxidant compounds and to reduce the enzymatic activity of a pitaya-pineapple (Stenocereus sp.-Fragaria ananassa) beverage.

Pitaya (Stenocereus sp.) is a fruit native to arid and semiarid areas of Mexico. It has high antioxidant activity mainly due to its contents of betalains and phenolics, but its consumption is limited due to very short shelf-life and not very recognized flavor. A beverage of pitaya and pineapple was formulated to improve sensory properties. A high hydrostatic pressure (HHP) study at 400-600 MPa and 25 °C for 2-10 min was applied in the beverage and the effect on the contents of vitamin C, total phenolics and betalains, and the pectin methylesterase (PME) activity of pitaya-pineapple beverages, was evaluated. The effect of the come up time (CUT) was also studied. Vitamin C contents increased from 5% at 600 MPa-CUT to 64% at 400 MPa/CUT. Total phenolic concentrations decreased (20-48%) at all processing conditions tested at 400 MPa/CUT, total betacyanins were retained. At 500 MPa/10 min losses of betaxanthins of up to 6% occurred. The maximum PME activity decrease was 23% at 600 MPa 5 min, but an increase of PME activity 7% was observed at 400 MPa/10 min. HHP seem to be a good option to retain most of the antioxidant compounds in pitaya-pineapple beverage, but more studies are necessary to inactivate PME.

Combined effect of high hydrostatic pressure and mild heat treatments on pectin methylesterase (PME) inactivation in comminuted orange.

BACKGROUND: Comminuted orange, a product obtained by grinding the juice and peel and used to formulate beverages, has a high pectin methylesterase (PME) activity; thus the inactivation of this enzyme is necessary to avoid quality losses related to cloud loss. The use of high hydrostatic pressure (HHP) and mild temperature allows inactivation of enzymes with minimal quality changes. This work aimed to evaluate the effect of pressure, mild temperature and time of treatment, including come-up and holding time, on the inactivation of PME in comminuted orange, and to apply kinetic and response surface models (RSM) to predict residual PME activity (A/A0 ). RESULTS: During come-up time in treatments at 68 °C, the higher the pressure, the lower was the A/A0 obtained. At 550 MPa/68 °C/10 min the lowest residual activity value was obtained (15.6%). A/A0 was well adjusted to the RSM, and a first-order kinetic model was applied to describe the inactivation of PME. In general, the higher the pressure, the lower was the A/A0 reached, as the increasing values of k from 3.5 × 10(-2) to 55.5 × 10(-2) min(-1) indicated. Activation volume (Va ) values ranging from -9.2 to -17.7 cm(3) mol(-1) , and activation energies (Ea ) between 50.0 and 68.2 kJ mol(-1) were calculated. CONCLUSION: 550 MPa/68 °C/10 min, 350 MPa/68 °C/10 min and 450 MPa/56 °C/10 min treatments were satisfactory (∼84% inactivation) to inactivate PME. A first-order kinetic model was applied to describe PME inactivation, and the resulting A/A0 adjusted to the RSM. In addition, linearized Arrhenius and Eyring equations were well fitted in order to obtain Ea and Va , respectively.

Microstructural Changes in Vanilla planifolia Beans after Using High-Hydrostatic-Pressure Treatment in the Curing Process.

During vanilla bean curing, the cell arrangement derived from the killing technique applied to start bean ripening is essential to obtain the characteristic aroma and flavor of vanilla. Hence, killing is an important step to release the enzymes and compounds required for vanillin production. In this work, high hydrostatic pressure (HHP) at 100-400 MPa for 5 min, using water at 7 °C as the pressure-transmitting medium, was applied as the killing method, and its effect on the microstructural changes in vanilla beans during different curing cycles (C0-C20) was evaluated and compared with that observed after scalding by using water at 100 °C for 8 s. Microstructural changes in the cross-sectioned beans were analyzed using a stereomicroscope (SM), confocal laser scanning microscopy (CLSM), and environmental scanning electron microscopy (ESEM). The vanilla beans were cross-sectioned and three main sectors were analyzed: the total, annular, and core. The morphometric descriptors, namely, area, Feret's diameter, and circularity, were quantified via digital image analysis (DIA), from which a shrinkage ratio was calculated. The results show that the total area in the beans presented a maximum decrease in the C16 of curing. The core area was most affected by the HHP treatment, mainly at 400 MPa, rather than scalding. CSLM observations revealed the autofluorescence of the compounds inside the beans. In conclusion, the use of microscopy techniques and DIA allowed us to determine the microstructural changes in the HHP-treated pods, which were found to be more numerous than those found in the scalded beans.

Improvement in the Stability and Bioaccessibility of Carotenoid and Carotenoid Esters from a Papaya By-Product Using O/W Emulsions.

The aim of the present work was to improve the stability and bioaccessibility of carotenoids from green oil extracts obtained from papaya by-products using oil-in-water (O/W) emulsions. The effects of different concentrations of pectin (1%, 2%, and 3%), a high-molecular-size emulsifier, together with Tween 20, a low-molecular-size emulsifier, high-speed homogenization conditions (time: 2, 3, 4, and 5 min; rpm: 9500, 12,000, 14,000, and 16,000 rpm), and high-pressure homogenization (HPH) (100 MPa for five cycles) were evaluated to determine the optimal conditions for obtaining O/W stable emulsions with encapsulated carotenoids. Soybean, sunflower, and coconut oils were used to formulate these O/W emulsions. The bioaccessibility of the main individual encapsulated papaya carotenoids was evaluated using the INFOGEST digestion methodology. In addition, the microstructures (confocal and optical microscopy) of the O/W carotenoid emulsions and their behavior during in vitro digestion phases were studied. Sunflower O/W carotenoid emulsions showed smaller mean particle size, higher negative ζ-potential, and higher viscosity than soybean O/W emulsions. Particle size reduction in the O/W emulsions using the HPH process improved the bioaccessibility of papaya encapsulated carotenoids. In these O/W emulsions, depending on the vegetable oil, lycopene was the carotenoid with the highest bioaccessibility (71-64%), followed by (all-E)-ß-carotene (18%), (all-E)-ß-cryptoxanthin (15%), and (all-E)-ß-cryptoxanthin laurate (7-4%). These results highlight the potential of using green carotenoid papaya extracts to formulate O/W emulsions to enhance carotenoid bioactivity by efficiently preventing degradation and increasing in vitro bioaccessibility.

Breast milk preservation: thermal and non-thermal processes and their effect on microorganism inactivation and the content of bioactive and nutritional compounds.

Human Breast Milk (HBM) is widely acknowledged as the best nutritional source for neonates. Data indicates that, in 2019, 83.2% of infants in the United States received breast milk at birth, slightly reducing to 78.6% at 1 month. Despite these encouraging early figures, exclusive breastfeeding rates sharply declined, dropping to 24.9% by 6 months. This decline is particularly pronounced when direct breastfeeding is challenging, such as in Neonatal Intensive Care Units (NICU) and for working mothers. Given this, it is vital to explore alternative breast milk preservation methods. Technologies like Holder Pasteurization (HoP), High-Temperature Short-Time Pasteurization (HTST), High-Pressure Processing (HPP), UV radiation (UV), and Electric Pulses (PEF) have been introduced to conserve HBM. This review aims to enhance the understanding of preservation techniques for HBM, supporting the practice of extended exclusive breastfeeding. It explicitly addresses microbial concerns, focusing on critical pathogens like Staphylococcus aureus, Enterococcus, Escherichia coli, Listeria monocytogenes, and Cytomegalovirus, and explores how various preservation methods can mitigate these risks. Additionally, the review highlights the importance of retaining the functional elements of HBM, particularly its immunological components such as antibodies and enzymes like lysozyme and Bile Salt Stimulated Lipase (BSSL). The goal is to provide a comprehensive overview of the current state of HBM treatment, critically assess existing practices, identify areas needing improvement, and advocate for extended exclusive breastfeeding due to its vital role in ensuring optimal nutrition and overall health in infants.

Metabolite transformation and ß-d-glucosidase activity during the high hydrostatic pressure assisted curing of vanilla beans (Vanilla planifolia) to improve phenolic compounds formation.

Current methods for vanilla bean curing are long and reduce the enzymatic activity necessary for flavor development. High hydrostatic pressure (HHP) at 50-600 MPa was used to improve phenolic compounds formation and ß-d-glucosidase activity in vanilla beans compared with scalded beans. Phenolics were analyzed by HPLC and ß-d-glucosidase activity by spectrophotometry. Vanillin was the main phenolic and it was formed by ß-d-glucovanillin hydrolysis and vanillyl alcohol oxidation. HHP improved vanillin content and influenced ß-d-glucosidase activity. At the beginning of the curing the highest increments of vanillin were produced at 400 MPa (up to 15%), while at the end, this was observed at 50 (138%) and 600 MPa (74%). Maximum increment of up to 400% in ß-d-glucosidase activity was observed from 100 to 300 MPa, which was attributed to tissue decompartmentalization, and conformational changes induced by pressure. HHP could be used during vanilla curing to improve vanillin content and ß-d-glucosidase activity.