Evaluation of a Commercial Ballistocardiography Sensor for Sleep Apnea Screening and Sleep Monitoring.

There exists a technological momentum towards the development of unobtrusive, simple, and reliable systems for long-term sleep monitoring. An off-the-shelf commercial pressure sensor meeting these requirements is the Emfit QS. First, the potential for sleep apnea screening was investigated by revealing clusters of contaminated and clean segments. A relationship between the irregularity of the data and the sleep apnea severity class was observed, which was valuable for screening (sensitivity 0.72, specificity 0.70), although the linear relation was limited ( R 2 of 0.16). Secondly, the study explored the suitability of this commercial sensor to be merged with gold standard polysomnography data for future sleep monitoring. As polysomnography (PSG) and Emfit signals originate from different types of sensor modalities, they cannot be regarded as strictly coupled. Therefore, an automated synchronization procedure based on artefact patterns was developed. Additionally, the optimal position of the Emfit for capturing respiratory and cardiac information similar to the PSG was identified, resulting in a position as close as possible to the thorax. The proposed approach demonstrated the potential for unobtrusive screening of sleep apnea patients at home. Furthermore, the synchronization framework enabled supervised analysis of the commercial Emfit sensor for future sleep monitoring, which can be extended to other multi-modal systems that record movements during sleep.

Heart beat detection in multimodal data using automatic relevant signal detection.

Accurate R peak detection in the electrocardiogram (ECG) is a well-known and highly explored problem in biomedical signal processing. Although a lot of progress has been made in this area, current methods are still insufficient in the presence of extreme noise and/or artifacts such as loose electrodes. Often, however, not only the ECG is recorded, but multiple signals are simultaneously acquired from the patient. Several of these signals, such as blood pressure, can help to improve the heart beat detection. These signals of interest can be detected automatically by analyzing their power spectral density or by using the available signal type identifiers. Individual peaks from the signals of interest are combined using majority voting, heart beat location estimation and Hjorth's mobility of the resulting RR intervals. Both multimodal algorithms showed significant increases in performance of up to 8.65% for noisy multimodal datasets compared to when only the ECG signal is used. A maximal performance of 90.02% was obtained on the hidden test set of the Physionet/Computing in Cardiology Challenge 2014: Robust Detection of Heart Beats in Multimodal Data.

Characterization of the respiratory and heart beat signal from an air pressure-based ballistocardiographic setup.

Off-body detection of respiratory and cardiac activity presents an enormous opportunity for general health, stress and sleep quality monitoring. The presented setup detects the mechanical activity of both heart and lungs by measuring pressure difference fluctuations between two air volumes underneath the chest area of the subject. The registered signals were characterized over four different sleep postures, three different base air pressures within the air volumes and three different mattress top layer materials. Highest signal strength was detected in prone posture for both the respiratory and heart beat signal. Respiratory signal strength was the lowest in supine posture, while heart beat signal strength was lowest for right lateral. Heart beat cycle variability was highest in prone and lowest in supine posture. Increasing the base air pressure caused a reduction in signal amplitude for both the respiratory and the heart beat signal. A visco-elastic poly-urethane foam top layer had significantly higher respiration amplitude compared to high resilient poly-urethane foam and latex foam. For the heart beat signal, differences between the top layers were small. The authors conclude that, while the influence of the mattress top layer material is small, the base air pressure can be tuned for optimal mechanical transmission from heart and lungs towards the registration setup.

Automatic sleep stage classification based on easy to register signals as a validation tool for ergonomic steering in smart bedding systems.

Ergonomic sleep studies benefit from long-term monitoring in the home environment to cope with daily variations and habituation effects. Polysomnography allows to asses sleep accurately, but is costly, time-consuming and possibly disturbing for the sleeper. Actigraphy is cheap and user friendly, but for many studies lacks accuracy and detailed information. This proof-of-concept study investigates Least-Squares Support Vector Machines as a tool for automatic sleep stage classification (Wake-N1-Rem to N2-N3 separation), using automatic trainingset-specific filtered features as derived from three easy to register signals, namely heart rate, breathing rate and movement. The algorithms are trained and validated using 20 nights out of a 600 night database from over 100 different healthy persons. Different training and test set strategies were analyzed leading to different results. The more person-specific the training nights to the test nights, the better the classification accuracy as validated against the hypnograms scored by experts from the full polysomnograms. In the limit of complete person-specific training, the accuracy of the algorithm on the test set reached 94%. This means that this algorithm could serve its use in long-term monitoring sleep studies in the home environment, especially when prior person-specific polysomnographic training is performed.