RESUMO
Influences of discharge voltage on wheat seed vitality were investigated in a dielectric barrier discharge (DBD) plasma system at atmospheric pressure and temperature. Six different treatments were designed, and their discharge voltages were 0.0, 9.0, 11.0, 13.0, 15.0, and 17.0 kV, respectively. Fifty seeds were exposed to the DBD plasma atmosphere with an air flow rate of 1.5 L min-1 for 4 min in each treatment, and then the DBD plasma-treated seeds were prepared for germination in several Petri dishes. Each treatment was repeated three times. Germination indexes, growth indexes, surface topography, water uptake, permeability, and α-amylase activity were measured. DBD plasma treatment at appropriate energy levels had positive effects on wheat seed germination and seedling growth. The germination potential, germination index, and vigor index significantly increased by 31.4%, 13.9%, and 54.6% after DBD treatment at 11.0 kV, respectively, in comparison to the control. Shoot length, root length, dry weight, and fresh weight also significantly increased after the DBD plasma treatment. The seed coat was softened and cracks were observed, systematization of the protein was strengthened, and amount of free starch grain increased after the DBD plasma treatment. Water uptake, relative electroconductivity, soluble protein, and α-amylase activity of the wheat seed were also significantly improved after the DBD plasma treatment. Roles of active species and ultraviolet radiation generated in the DBD plasma process in wheat seed germination and seedling growth are proposed. Bioelectromagnetics. 39:120-131, 2018. © 2017 Wiley Periodicals, Inc.
Assuntos
Gases em Plasma/farmacologia , Sementes/efeitos dos fármacos , Sementes/crescimento & desenvolvimento , Triticum/efeitos dos fármacos , Triticum/crescimento & desenvolvimento , Transporte Biológico/efeitos dos fármacos , Impedância Elétrica , Germinação/efeitos dos fármacos , Proteínas de Plantas/metabolismo , Plântula/efeitos dos fármacos , Plântula/crescimento & desenvolvimento , Triticum/metabolismo , Água/metabolismo , alfa-Amilases/metabolismoRESUMO
The efficiency and longevity of metal-halide perovskite solar cells are typically dictated by nonradiative defect-mediated charge recombination. In this work, we demonstrate a vapor-based amino-silane passivation that reduces photovoltage deficits to around 100 millivolts (>90% of the thermodynamic limit) in perovskite solar cells of bandgaps between 1.6 and 1.8 electron volts, which is crucial for tandem applications. A primary-, secondary-, or tertiary-amino-silane alone negatively or barely affected perovskite crystallinity and charge transport, but amino-silanes that incorporate primary and secondary amines yield up to a 60-fold increase in photoluminescence quantum yield and preserve long-range conduction. Amino-silane-treated devices retained 95% power conversion efficiency for more than 1500 hours under full-spectrum sunlight at 85°C and open-circuit conditions in ambient air with a relative humidity of 50 to 60%.
RESUMO
Direct seawater electrolysis is promising for sustainable hydrogen gas (H2) production. However, the chloride ions in seawater lead to side reactions and corrosion, which result in a low efficiency and poor stability of the electrocatalyst and hinder the use of seawater electrolysis technology. Here we report a corrosion-resistant RuMoNi electrocatalyst, in which the in situ-formed molybdate ions on its surface repel chloride ions. The electrocatalyst works stably for over 3000 h at a high current density of 500 mA cm-2 in alkaline seawater electrolytes. Using the RuMoNi catalyst in an anion exchange membrane electrolyzer, we report an energy conversion efficiency of 77.9% and a current density of 1000 mA cm-2 at 1.72 V. The calculated price per gallon of gasoline equivalent (GGE) of the H2 produced is $ 0.85, which is lower than the 2026 technical target of $ 2.0/GGE set by the United Stated Department of Energy, thus, suggesting practicability of the technology.
Assuntos
Cloretos , Gasolina , Corrosão , Ânions , Membranas , Halogênios , Água do MarRESUMO
Constructing stable electrodes which function over long timescales at large current density is essential for the industrial realization and implementation of water electrolysis. However, rapid gas bubble detachment at large current density usually results in peeling-off of electrocatalysts and performance degradation, especially for long term operations. Here we construct a mechanically-stable, all-metal, and highly active CuMo6S8/Cu electrode by in-situ reaction between MoS2 and Cu. The Chevrel phase electrode exhibits strong binding at the electrocatalyst-support interface with weak adhesion at electrocatalyst-bubble interface, in addition to fast hydrogen evolution and charge transfer kinetics. These features facilitate the achievement of large current density of 2500 mA cm-2 at a small overpotential of 334 mV which operate stably at 2500 mA cm-2 for over 100 h. In-situ total internal reflection imaging at micrometer level and mechanical tests disclose the relationships of two interfacial forces and performance of electrocatalysts. This dual interfacial engineering strategy can be extended to construct stable and high-performance electrodes for other gas-involving reactions.
RESUMO
The use of highly-active and robust catalysts is crucial for producing green hydrogen by water electrolysis as we strive to achieve global carbon neutrality. Noble metals like platinum are currently used catalysts in industry for the hydrogen evolution, but suffer from scarcity, high price and unsatisfied performance and stability at large current density, restrict their large-scale implementations. Here we report the synthesis of a type of monolith catalyst consisting of a metal disulfide (e.g., tantalum sulfides) vertically bonded to a conductive substrate of the same metal tantalum by strong covalent bonds. These features give the monolith catalyst a mechanically-robust and electrically near-zero-resistance interface, leading to an excellent hydrogen evolution performance including rapid charge transfer and excellent durability, together with a low overpotential of 398 mV to achieve a current density of 2,000 mA cm-2 as required by industry. The monolith catalyst has a negligible performance decay after 200 h operation at large current densities. In light of its robust and metallic interface and the various choices of metals giving the same structure, such monolith materials would have broad uses besides catalysis.
RESUMO
The high-throughput scalable production of cheap, efficient and durable electrocatalysts that work well at high current densities demanded by industry is a great challenge for the large-scale implementation of electrochemical technologies. Here we report the production of a two-dimensional molybdenum disulfide-based ink-type electrocatalyst by a scalable exfoliation technique followed by a thermal treatment. The catalyst delivers a high current density of 1000 mA cm-2 at an overpotential of 412 mV for the hydrogen evolution. Using the same method, we produce a cheap mineral-based catalyst possessing excellent performance for high-current-density hydrogen evolution. Noteworthy, production rate of this catalyst is one to two orders of magnitude higher than those previously reported, and price of the mineral is five orders of magnitude lower than commercial Pt electrocatalysts. These advantages indicate the huge potentials of this method and of mineral-based cheap and abundant natural resources as catalysts in the electrochemical industry.