Porous Polyethylene Supports in Reinforcement of Multiblock Hydrocarbon Ionomers for Proton Exchange Membranes.

Hydrocarbon (HC)-based block copolymers have been recognized as promising candidates for proton exchange membranes (PEMs) due to their distinct hydrophilic-hydrophobic separation, which results in improved proton transport compared to that of random copolymers. However, most PEMs derived from HC-based ionomers, including block copolymers, encounter challenges related to durability in electrochemical cells due to their low mechanical and chemical properties. One method for reinforcing HC-based ionomers involves incorporating the ionomers into commercially available low surface tension PTFE porous substrates. Nevertheless, the high interfacial energy between the hydrocarbon-based ionomer solution and PTFE remains a challenge in this reinforcement process, which necessitates the application of surface energy treatment to PTFE. Here, multiblock sulfonated poly(arylene ether sulfone) (SPAES) ionomers are being reinforced using untreated PE on the surface, and this is compared to reinforcement using surface-treated porous PTFE. The PE support layer exhibits a lower surface energy barrier compared to the surface-treated PTFE layer for the infiltration of the multiblock SPAES solution. This is characterized by the absence of noticeable voids, high translucency, gas impermeability, and a physical and chemical stability. By utilizing a high surface tension PE support with a comparable value to the multiblock SPAES, effective reinforcement of the multiblock SPAES ionomers is achieved for a PEM, which is potentially applicable to various hydrogen energy-based electrochemical cells.

Alcohol-Treated Porous PTFE Substrate for the Penetration of PTFE-Incompatible Hydrocarbon-Based Ionomer Solutions.

For a mechanically tough proton exchange membrane, a composite membrane incorporated with a porous polymer substrate is of great interest to suppress the ionomer swelling and to improve the dimensional stability and mechanical strength of the ionomers. For the composite membranes, good impregnation of substrate-incompatible ionomer solution into the substrate pores still remains one of the challenges to be solved. Here, we demonstrated a facile process (surface treatment with solvents compatible with both substrate and the ionomer solution) for the fabrication of the composite membranes using polytetrafluoroethylene (PTFE) as a porous substrate and poly(arylene ether sulfone) (SPAES) as a hydrocarbon-based (HC) ionomer. Appropriate solvents for the surface treatment were sought through the contact angle measurement, and it was found that alcohol solvents effectively tuned the surface property of PTFE pores to facilitate the penetration of the SPAES/N-methyl-2-pyrrolidone (NMP) solution into ∼300 nm pores of the substrate. Using this simple alcohol treatment, the SPAES/NMP contact angle was reduced in half, and we could fabricate the mechanically tough PTFE/HC composite membranes, which were apparently translucent and microscopically almost void-free composite membranes.

Transforming Ionene Polymers into Efficient Cathode Interlayers with Pendent Fullerenes.

A new and highly efficient cathode interlayer material for organic photovoltaics (OPVs) was produced by integrating C60 fullerene monomers into ionene polymers. The power of these novel "C60 -ionenes" for interface modification enables the use of numerous high work-function metals (e.g., silver, copper, and gold) as the cathode in efficient OPV devices. C60 -ionene boosted power conversion efficiencies (PCEs) of solar cells, fabricated with silver cathodes, from 2.79 % to 10.51 % for devices with a fullerene acceptor in the active layer, and from 3.89 % to 11.04 % for devices with a non-fullerene acceptor in the active layer, demonstrating the versatility of this interfacial layer. The introduction of fullerene moieties dramatically improved the conductivity of ionene polymers, affording devices with high efficiency by reducing charge accumulation at the cathode/active layer interface. The power of C60 -ionene to improve electron injection and extraction between metal electrodes and organic semiconductors highlights its promise to overcome energy barriers at the hard-soft materials interface to the benefit of organic electronics.

Hydrocarbon-Based Composite Membrane Using LCP-Nonwoven Fabrics for Durable Proton Exchange Membrane Water Electrolysis.

A new hydrocarbon-based (HC) composite membrane was developed using liquid crystal polymer (LCP)-nonwoven fabrics for application in proton exchange membrane water electrolysis (PEMWE). A copolymer of sulfonated poly(arylene ether sulfone) with a sulfonation degree of 50 mol% (SPAES50) was utilized as an ionomer for the HC membranes and impregnated into the LCP-nonwoven fabrics without any surface treatment of the LCP. The physical interlocking structure between the SPAES50 and LCP-nonwoven fabrics was investigated, validating the outstanding mechanical properties and dimensional stability of the composite membrane in comparison to the pristine membrane. In addition, the through-plane proton conductivity of the composite membrane at 80 °C was only 15% lower than that of the pristine membrane because of the defect-free impregnation state, minimizing the decrease in the proton conductivity caused by the non-proton conductive LCP. During the electrochemical evaluation, the superior cell performance of the composite membrane was evident, with a current density of 5.41 A/cm2 at 1.9 V, compared to 4.65 A/cm2 for the pristine membrane, which can be attributed to the smaller membrane resistance of the composite membrane. From the results of the degradation rates, the prepared composite membrane also showed enhanced cell efficiency and durability during the PEMWE operations.

Multi-Block Copolymer Membranes Consisting of Sulfonated Poly(p-phenylene) and Naphthalene Containing Poly(arylene Ether Ketone) for Proton Exchange Membrane Water Electrolysis.

Glassy hydrocarbon-based membranes are being researched as a replacement for perfluorosulfonic acid (PFSA) membranes in proton exchange membrane water electrolysis (PEMWE). Here, naphthalene containing Poly(arylene Ether Ketone) was introduced into the Poly(p-phenylene)-based multi-block copolymers through Ni(0)-catalyzed coupling reaction to enhance π-π interactions of the naphthalene units. It is discovered that there is an optimum input ratio of the hydrophilic monomer and NBP oligomer for the multi-block copolymers with high ion exchange capacity (IEC) and polymerization yield. With the optimum input ratio, the naphthalene containing copolymer exhibits good hydrogen gas barrier property, chemical stability, and mechanical toughness, even with its high IEC value over 2.4 meq g-1. The membrane shows 3.6 times higher proton selectivity to hydrogen gas than Nafion 212. The PEMWE single cells using the membrane performed better (5.5 A cm-2) than Nafion 212 (4.75 A cm-2) at 1.9 V and 80 °C. These findings suggest that naphthalene containing copolymer membranes are a promising replacement for PFSA membranes in PEMWE.

Aluminum Diethylphosphinate-Incorporated Flame-Retardant Polyacrylonitrile Separators for Safety of Lithium-Ion Batteries.

Herein, we developed polyacrylonitrile (PAN)-based nanoporous composite membranes incorporating aluminum diethylphosphinate (ADEP) for use as a heat-resistant and flame-retardant separator in high-performance and safe lithium-ion batteries (LIBs). ADEP is phosphorus-rich, thermally stable, and flame retardant, and it can effectively suppress the combustibility of PAN nanofibers. Nanofibrous membranes were obtained by electrospinning, and the content of ADEP varied from 0 to 20 wt%. From the vertical burning test, it was demonstrated that the flame retardancy of the composite membranes was enhanced when more than 5 wt% of ADEP was added to PAN, potentially increasing the safety level of LIBs. Moreover, the composite membrane showed higher ionic conductivity and electrolyte uptake (0.83 mS/cm and 137%) compared to those of commercial polypropylene (PP) membranes (Celgard 2400: 0.65 mS/cm and 63%), resulting from interconnected pores and the polar chemical composition in the composite membranes. In terms of battery performance, the composite membrane showed highly stable electrochemical and heat-resistant properties, including superior discharge capacity when compared to Celgard 2400, indicating that the PAN/ADEP composite membrane has the potential to be used as a heat-resistant and flame-retardant separator for safe and high-power LIBs.

Orthogonally Aligned Block Copolymer Line Patterns on Minimal Topographic Patterns.

We demonstrate the generation of block copolymer (BCP) line patterns oriented orthogonal to a very small (minimal) topographic trench pattern over arbitrarily large areas using solvent-vapor annealing. Increasing the thickness of BCP films induced an orthogonal alignment of the BCP cylindrical microdomains, where full orthogonal alignment of the cylindrical microdomains with respect to the trench direction was obtained at a film thickness corresponding to 1.70 L0. A capillary flow of the solvent across the trenches was a critical factor in the alignment of the cylindrical microdomains. Grazing incidence small-angle X-ray scattering was used to determine the orientation function of the microdomains, with a value of 0.997 being found reflecting a nearly perfect orientation. This approach to produce orthogonally aligned BCP line patterns could be extended to the nanomanufacturing and fabrication of hierarchical nanostructures.