A Water-Based Biocoating to Increase the Infection Resistance and Osteoconductivity of Titanium Surfaces.

As the population ages, the number of patients undergoing total hip arthroplasty (THA) and total knee arthroplasty (TKA) continues to increase. Infections after primary arthroplasty are rare but have high rates of morbidity and mortality, as well as enormous financial implications for healthcare systems. Numerous methods including the use of superhydrophobic coatings, the incorporation of antibacterial agents, and the application of topographical treatments have been developed to reduce bacterial attachment to medical devices. However, most of these methods require complex manufacturing processes. Thus, the main purpose of this study was to apply biocoatings to titanium (Ti) surfaces to increase their infection resistance and osteoconductivity via simple processes, without organic reagents. We modified titanium surfaces with a combination of aminomalononitrile (AMN) and an antibiotic-loaded mesoporous bioactive glass (MBG) and evaluated both the antibacterial effects of the coating layer and its effect on osteoblast proliferation and differentiation. The properties of the modified surface, such as the hydrophilicity, roughness, and surface morphology, were characterized via contact angle measurements, atomic force microscopy, and scanning electron microscopy. The cell proliferation reagent WST-1 assay and the alkaline phosphatase (ALP) assay were used to determine the degrees of adhesion and differentiation, respectively, of the MG-63 osteoblast-like cells on the surface. Antimicrobial activity was evaluated by examining the survival rate and inhibition zone of Escherichia coli (E. coli). The AMN coating layer reduced the water contact angle (WCA) of the titanium surface from 87° ± 2.5° to 53° ± 2.3° and this change was retained even after immersion in deionized water for five weeks, demonstrating the stability of the AMN coating. Compared with nontreated titanium and polydopamine (PDA) coating layers, the AMN surface coating increased MG-63 cell attachment, spreading, and early ALP expression; reduced E. coli adhesion; and increased the percentage of dead bacteria. In addition, the AMN coating served as an adhesion layer for the subsequent deposition of MBG-containing antibiotic nanoparticles. The synergistic effects of the AMN layer and antibiotics released from the MBG resulted in an obvious E. coli inhibition zone that was not observed in the nontreated titanium group.

Novel Extrapolymeric Substances Biocoating on Polyvinylidene Fluoride Membrane for Enhanced Attached Growth of Navicula incerta.

Cell adhesion is always the first step in biofilm development. With the emergence of attached cultivation systems, this study aims to promote a cost-effective approach for sustainable cultivation of microalgae, Navicula incerta, by pre-coating the main substrates, commercial polyvinylidene fluoride (PVDF) membranes with its own washed algal cells and self-produced soluble extracellular polymeric substances (EPS) for strengthened biofilm development. The effects of pH value (6 to 9), cell suspension volume (10 to 30 mL), and EPS volume (10 to 50 mL) were statistically optimized by means of response surface methodology toolkit. Model outputs revealed good agreement with cell adhesion data variation less than 1% at optimized pre-coating conditions (7.20 pH, 30 mL cell suspension volume, and 50 mL EPS volume). Throughout long-term biofilm cultivation, results demonstrated that EPS pre-coating substantially improved the attached microalgae density by as high as 271% than pristine PVDF due to rougher surface and the presence of sticky exopolymer particles. Nutrients absorbed via the available EPS coating from the bulk medium made the immobilized cells to release less polysaccharides on an average of 30% less than uncoated PVDF. This work suggests that adhesive polymer binders derived from organic sources can be effectively integrated into the development of high-performance novel materials as biocoating for immobilized microalgae cultivation.

Bio-coatings in permeated cultivation systems: Unprecedented impacts on microalgal monoculture growth and organic matter yield.

Bio-coating, a recent and promising approach in attached microalgal cultivation systems, has garnered attention due to its efficiency in enhancing immobilized algal growth, particularly in submerged cultivation systems. However, when the cells are cultured on thin solid microporous substrates that physically separate them from the nutrient medium, it remains unclear whether the applied bio-coatings still have a significant impact on algal growth or the subsequent rates of algal organic matter (AOM) release. Therefore, this current work investigated the role of bio-coatings on the microalgal monoculture growth of one freshwater species, Chlorella vulgaris ESP 31, and one marine species, Cylindrotheca fusiformis on a hydrophilic substrate, polyvinylidene fluoride membrane in a permeated cultivation system. Wide range of bio-coating sources were adapted, with the result demonstrating that bacteria-derived coating promoted algal growth by as high as 140% when compared with the control group for both species. Interestingly, two distinct adaptation mechanisms were observed between the species, with only C. fusiformis demonstrating a positive correlation between cell growth and AOM productivity, particularly in its extracellularly bound fractions. It is worth noting that despite this specific fraction exhibiting the lowest content among all; it displayed significant relevance in terms of AOM productivity. High extracellular protein-to-polysaccharide ratio (>5.7 fold) quantified on bacterial intracellular exudate-coated membranes indirectly revealed an underlying symbiotic microalgal-bacterial interaction. This is the first study showing how bio-coating influenced AOM yield without any physical interaction between microalgae and bacteria. It further confirms the practical benefits of bio-coating in attached cultivation systems.

Effect of D-Limonene Nanoemulsion Edible Film on Banana (Musa sapientum Linn.) Post-Harvest Preservation.

D-limonene (4-isopropenyl-1-methylcyclohexene) is an important compound in several citrus essential oils (such as orange, lemon, tangerine, lime, and grapefruit). It has been used as a flavoring agent and as a food preservative agent, with generally recognized as safe (GRAS) status. D-limonene has been well-studied for its anti-inflammatory, antioxidant, anti-cancer, and antibacterial properties. The antibacterial activity of D-limonene against food-borne pathogens was investigated in this study by preparing a D-limonene nanoemulsion. The D-limonene solution and nanoemulsion have been prepared in six concentrations, 0.04%, 0.08%, 0.1%, 0.2%, 0.4%, and 0.8% (v/v), respectively, and the antibacterial activity was tested against four food-borne pathogens (Staphylococcus aureus, Listeria monocytogenes, Salmonella enterica, and Escherichia coli). The results showed that the D-limonene nanoemulsion had good nanoscale and overall particle size uniformity, and its particle size was about 3~5 nm. It has been found that the D-limonene solution and nanoemulsion have a minimal inhibitory concentration of 0.336 mg/mL, and that they could inhibit the growth of microorganisms efficiently. The data indicate that the D-limonene nanoemulsion has more antibacterial ability against microorganisms than the D-limonene essential oil. After bananas are treated with 1.0% and 1.5% D-limonene nanoemulsion coatings, the water loss of the bananas during storage and the percentage of weight loss are reduced, which can inhibit the activity of pectinase. The application of a biocoating provides a good degree of antibacterial activity and air and moisture barrier properties, which help with extending the shelf life of bananas.

Ag nanoparticles generated using bio-reduction and -coating cause microbial killing without cell lysis.

Cost-effective "green" methods of producing Ag nanoparticles (NPs) are being examined because of the potential of these NPs as antimicrobials. Ag NPs were generated from Ag ions using extracellular metabolites from a soil-borne Pythium species. The NPs were variable in size, but had one dimension less than 50 nm and were biocoated; aggregation and coating changed with acetone precipitation. They had dose-dependent lethal effects on a soil pseudomonad, Pseudomonas chlororaphis O6, and were about 30-fold more effective than Ag(+) ions. A role of reactive oxygen species in cell death was demonstrated by use of fluorescent dyes responsive to superoxide anion and peroxide accumulation. Also mutants of the pseudomonad, defective in enzymes that protect against oxidative stress, were more sensitive than the wild type strain; mutant sensitivity differed between exposure to Ag NPs and Ag(+) ions demonstrating a nano-effect. Imaging of bacterial cells treated with the biocoated Ag NPs revealed no cell lysis, but there were changes in surface properties and cell height. These findings support that biocoating the NPs results in limited Ag release and yet they retained potent antimicrobial activity.

Explosive weld joint characteristics of Copper-Tantalum via simulation.

This report aims to examine the effects of impact velocity, impact depth, and impact orientation on the Cu-Ta weld joint of the explosive welding process via MD simulation. The findings indicate that the residual shear stress in the welded block mostly increases as the impact velocity rises. The bottom Ta block is more severely distorted than the higher Cu block due to the impact direction. During the tensile test, three stress zones can be identified including the low-stress Cu block, the high-stress Ta block, and the medium-stress weld joint in the middle of the samples. The weld joint position is lower than the median line of the welded block. The Cu-Ta welded block with 500 m/s impact velocities had the highest ultimate tensile strength (UTS) value of 6.49 GPa. With increasing impact depth, the atomic strain level, residual shear stress, and weld joint dimensions all noticeably increase. The Cu-Ta welded block with an impact depth of 7.5 Å has the greatest UTS values, measuring 11.65 GPa, because of its well-crystal structure. Changing the impact orientation does not result in a dramatic change in atomic strain. Orientation (001) vs (001) has the highest strain and stress rates. With an impact orientation of (110) vs. (111), the Cu-Ta welded block gets the highest UTS value of 8.03 GPa compared to other orientations.

Efficient Bioactive Surface Coatings with Calcium Minerals: Step-Wise Biomimetic Transformation of Vaterite to Carbonated Apatite.

Carbonated apatite (CAp), known as the main mineral that makes up human bone, can be utilized in conjunction with scaffolds to increase their bioactivity. Various methods (e.g., co-precipitation, hydrothermal, and biomimetic coatings) have been used to provide bioactivity by forming CAp on surfaces similar to bone minerals. Among them, the use of simulated body fluids (SBF) is the most popular biomimetic method for generating CAp, as it can provide a mimetic environment. However, coating methods using SBF require at least a week for CAp formation. The long time it takes to coat biomimetic scaffolds is a point of improvement in a field that requires rapid regeneration. Here, we report a step-wise biomimetic coating method to form CAp using calcium carbonate vaterite (CCV) as a precursor. We can manufacture CCV-transformed CAp (V-CAp) on the surface in 4 h at least by immersing CCV in a phosphate solution. The V-CAp deposited surface was analyzed using scanning electron microscopy (SEM) images according to the type of phosphate solutions to optimize the reaction conditions. X-ray diffraction (XRD) and attenuated total reflection-Fourier transform infrared (ATR-FTIR) analysis validated the conversion of CCV to V-CAp on surfaces. In addition, the bioactivity of V-CAp coating was analyzed by the proliferation and differentiation of osteoblasts in vitro. V-CAp showed 2.3-folded higher cell proliferation and 1.4-fold higher ALP activity than the glass surface. The step-wise method of CCV-transformed CAp is a biocompatible method that allows the environment of bone regeneration and has the potential to confer bioactivity to biomaterial surfaces, such as imparting bioactivity to non-bioactive metal or scaffold surfaces within one day. It can rapidly form carbonated apatite, which can greatly improve time efficiency in research and industrial applications.

Evaluation of bioactivity and antibacterial properties of Ti6Al4V-based green biocomposite implant encompassing TiO2 nanotube arrays and garlic extract.

This study involved the incorporation of an antibacterial garlic extract into titanium oxide nanotubes (TNTs) formed via the anodization of Ti6Al4V implants. The garlic extract, obtained through low-temperature extraction aided by ultrasound waves, was loaded into the nanotubes. The presence of the nanotubes was confirmed through X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), and scanning electron microscopy (SEM). Fourier-transform infrared spectroscopy (FT-IR) and gas chromatography-mass spectrometry (GC-MS) were used to investigate the presence of bioactive compounds, particularly sulfur compounds responsible for garlic's antibacterial effects. The impact of loading two concentrations (0.1 and 0.2 g per milliliter) of garlic extract on Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) bacteria was examined. Results indicated a decrease in the growth range of S. aureus from 109 to 106 (CFU/ml) and E. coli from 1011 to 109 (CFU/ml) upon treatment. Additionally, cell adhesion and viability tests conducted on MG63 cells revealed an 8% increase in cell viability with the 0.1 g per milliliter concentration and a 35% decrease with the 0.2 g per milliliter concentration of garlic extract after 72 h of incubation (They have been evaluated by Microculture tetrazolium (MTT) assay). GC-MS analysis identified the presence of diethyl phthalate compounds in the garlic extract, suggesting a potential correlation with cellular toxicity observed in the sample with the higher concentration (0.2 g per milliliter) of garlic extract. Overall, the TNTs loaded with 0.1 g per milliliter of garlic extract simultaneously demonstrated antibacterial activity, cell viability, adhesion, and growth enhancement.

Uncovering the role of algal organic matter biocoating on Navicula incerta cell deposition and biofilm formation.

Spontaneous natural biofilm concentrates microalgal biomass on solid supports. However, the biofilm is frequently susceptible to exfoliation upon nutrient deficiency, particularly found in aged biofilm. Therefore, this study highlights a novel biofilm cultivation technique by pre-depositing the algal organic matters from marine diatom, Navicula incerta onto microporous polyvinylidene fluoride membrane to further strengthen the biofilm developed. Due to the improvement in membrane surface roughness and hydrophobicity, cells adhered most abundantly to soluble extrapolymeric substances-coated (sEPS) (76×106±16×106 cells m-2), followed by bounded EPS-coated (57.67×106±0.33×106 cells m-2), internally organic matter (IOM)-coated (39.00×106±5.19×106 cells m-2), and pristine control the least (6.22×106±0.77×106 cells m-2) at 24th h. Surprisingly, only bEPS-coated membrane demonstrated an increase in cell adhesion toward the end of the experiment at 72 h. The application of the bio-coating has successfully increased the rate of cell attachment by at least 45.3% upon inoculation and achieved as high as 89.9% faster attachment at 72 hours compared to the pristine control group. Soluble polysaccharides and proteins might be carried along by the cells adhering onto membranes hence resulting in a built up of EPS hydrophobicity (>70% in average on bio-coated membranes) over time as compared with pristine (control) that only recorded an average of approximately 50% hydrophobicity. Interestingly, cells grown on bio-coated membranes accumulated more internally bounded polysaccharides, though bio-coating had no discernible impact on the production of both externally and internally bounded protein. The collective findings of this study reveal the physiological alterations of microalgal biofilms cultured on bio-coated membranes.

Microalgal extract as bio-coating to enhance biofilm growth of marine microalgae on microporous membranes.

Microalgal biofilm is a popular platform for algal production, nutrient removal and carbon capture; however, it suffers from significant biofilm exfoliation under shear force exposure. Hence, a biologically-safe coating made up of algal extracellular polymeric substances (EPS) was utilized to secure the biofilm cell retention and cell loading on commercial microporous membrane (polyvinylidene fluoride), making the surfaces more hydrophobic (contact angle increase up to 12°). Results demonstrated that initial cell adhesion of three marine microalgae (Amphora coffeaeformis, Cylindrotheca fusiformis and Navicula incerta) was enhanced by at least 1.3 times higher than that of pristine control within only seven days with minimized biofilm exfoliation issue due to uniform distribution of sticky transparent exopolymer particles. Bounded extracellular polysaccharide gathered was approximately 23% higher on EPS-coated membranes to improve the biofilm's hydraulic resistance, whereas bounded extracellular protein would only be substantially elevated after the attached cells re-accommodate themselves onto the EPS pre-coating of themselves. In accounting the rises of hydrophobic protein content, biofilm was believed to be more stabilized, presumably via hydrophobic interactions. EPS biocoating would generate a groundswell of interest for bioprocess intensifications though there are lots of inherent technical and molecular challenges to be further investigated in future.

Wood-derived bio-coating materials incorporating hydrophobic lignin and hierarchically porous biochar for high-efficiency coating slow-release fertilizers.

Coating slow-release fertilizers (CSRFs) have gained significant attention for their potential to improve nutrient utilization efficiency and prevent environmental pollution through mitigating soil and water contamination. This study developed a novel wood waste-derived composition as a bio-coating material for urea slow-release by integrating modified lignin (PCL) and activated biochar (ABC). PCL was prepared by grafting palmitoyl chloride (PC) with hydrophobic groups to the lignin via an esterification reaction. ABC with a high surface area and hierarchically porous structure created rich channels for ion transportation. These results increased the water-retention ability with a reduced absorbing/expelling rate and confer an excellent Cr(VI) adsorption capacity to the PCL and ABC hybrid coating material (PCL/ABC). The as-prepared PCL/ABC-based CSRF (PCL/ABC-CSRF) showed improving fertilizer slow-release properties for real application (nitrogen release persistence for 40 days at soil). The rice (Oryza sativa L.) hydroponics study suggested that such novel PCL/ABC was conducive to the rice growth in micro metallic contaminated hydroponics by eliminating the accumulation of chromium metal in rice roots. Overall, this study provides an attractive platform for developing biodegradable, heavy-metal adsorbable, and high-efficient CSRFs and a feasible and effective way for functionalized utilization of wood waste.

Construction of Multifunctional Zinc Ion Sustained-Release Biocoating on the Surface of Carbon Fiber Reinforced Polyetheretherketone with Enhanced Anti-inflammatory Activity, Angiogenesis, and Osteogenesis.

Current treatments of carbon fiber-reinforced polyetheretherketone (CFRPEEK) as orthopedic implants remain unsatisfactory due to the bioinert surface. The multifunctionalization of CFRPEEK, which endows it with regulating the immune inflammatory response, promoting angiogenesis, and accelerating osseointegration, is critical to the intricate bone healing process. Herein, a multifunctional zinc ion sustained-release biocoating, consisting of a carboxylated graphene oxide, zinc ion, and chitosan layer, covalently grafts on the surface of amino CFRPEEK (CP/GC@Zn/CS) to coordinate with the osseointegration process. The release behavior of zinc ions theoretically conforms to the different demands in the three stages of osseointegration, including the burst release of zinc ions in the early stage (7.27 µM, immunomodulation), continuous release in the middle stage (11.02 µM, angiogenesis), and slow release in the late stage (13.82 µM, osseointegration). In vitro assessments indicate that the multifunctional zinc ion sustained-release biocoating can remarkably regulate the immune inflammatory response, decrease the oxidative stress level, and promote angiogenesis and osteogenic differentiation. The rabbit tibial bone defect model further confirms that, compared to the unmodified group, the bone trabecular thickness of the CP/GC@Zn/CS group increases 1.32-fold, and the maximum push-out force improves 2.05-fold. In this study, a multifunctional zinc ion sustained-release biocoating constructed on the surface of CFRPEEK that conforms to the requirements of different osseointegration stages can be an attractive strategy for the clinical application of inert implants.

Structural characterization of a homopolysaccharide produced by Weissella cibaria FMy 2-21-1 and its potential application as a green corrosion inhibiting film.

Steel corrosion is a global issue that affects safety and the economy. Currently, the homopolysaccharide (HoPS) structure of a novel lactic acid bacterium (LAB) is under study, as well as its application as a green corrosion inhibitor. Weissella cibaria FMy 2-21-1 is a LAB strain capable of producing HoPS in sucrose enriched media. The isolated and purified HoPS was characterized by different spectroscopic analyses as a linear α-1,6 dextran adopting a random coil conformation, with high molecular weight and extended size in water. The polysaccharide showed a semi-crystalline organization, which is a requirement for film formation. Its biocoating showed a grainy network structure, with a slightly lesser hydrophobic role in the aqueous environment than in the ionic one. The electrochemical measurements of the steel-HoPS coating showed that the biopolymer layer acts as an anodic-type corrosion inhibitor, with high resistance to corrosion by water and with chloride ions which prevent pitting, a corrosion process typical of bare steel. Few reports have cited the application of LAB HoPS as corrosive coating inhibitors. This work is the first to explore the influence of a structurally characterized dextran from Weissella cibaria strain as a potential steel corrosion inhibitor in ionic environments.

Algal extracellular organic matter pre-treatment enhances microalgal biofilm adhesion onto microporous substrate.

Adhesive biocoating has microstructure composed of biomolecules to entrap viable cells in a stabilized matrix over exposed surfaces. Although marine benthic diatoms are a common group of algae excreting substantial amount of extracellular polymeric substances (EPS), studies regarding the utilization of these EPS are scarce. Using the soluble EPS derived from Navicula incerta and pre-deposition of it as a thin conditioning layer on microporous polyvinylidene fluoride (PVDF) membranes, the pre-coated surface was used to investigate the cell binding affinity of three marine microalgae, namely Amphora coffeaeformis, Cylindrotheca fusiformis and Navicula incerta. Microalgae actively engaged themselves on the pre-coated membranes which was 10 times greater than the initial cell adhesion degree. Soluble EPS is mainly comprised of polysaccharide while bounded EPS is mainly comprised of protein. On EPS pre-coated membranes, N. incerta released the least amount of bounded polysaccharides (<100 mg m-2) and vice versa for the other two because EPS production is usually maximized to assist cell adhesion onto unfavorable substrates. In stark contrast, when the adaptation period (first 6 h) ended, cells began to secrete more bounded protein for cell growth, and an increasing trend of protein content found in N. incerta has verified its optimal adaptation onto the biocoating itself. On pristine PVDF membranes, the adhesion degree was ranked in ascending order: C. fusiformis, N. incerta and A. coffeaeformis. Interestingly, after the pre-coating process, the order was reported as: A. coffeaeformis, N. incerta and C. fusiformis, but it should be noted that C. fusiformis demonstrated fluctuating cell colonization degree and bounded EPS production over time. In other words, the biofilm's susceptibility was confirmed since the cells latched loosely on the membranes rather than in a biofilm matrix. Biocoating enables uniform cell distribution and firmer biofilm growth, opening the door to vast future applications in environmental bioremediation and sensing.

Transient coating of γ-Fe2O3 nanoparticles with glutamate for its delivery to and removal from brain nerve terminals.

Glutamate is the main excitatory neurotransmitter in the central nervous system and excessive extracellular glutamate concentration is a characteristic feature of stroke, brain trauma, and epilepsy. Also, glutamate is a potential tumor growth factor. Using radiolabeled ʟ-[14C]glutamate and magnetic fields, we developed an approach for monitoring the biomolecular coating (biocoating) with glutamate of the surface of maghemite (γ-Fe2O3) nanoparticles. The nanoparticles decreased the initial rate of ʟ-[14C]glutamate uptake, and increased the ambient level of ʟ-[14C]glutamate in isolated cortex nerve terminals (synaptosomes). The nanoparticles exhibit a high capability to adsorb glutamate/ʟ-[14C]glutamate in water. Some components of the incubation medium of nerve terminals, that is, 4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid (HEPES) and NaH2PO4, decreased the ability of γ-Fe2O3 nanoparticles to form a glutamate biocoating by about 50% and 90%, respectively. Only 15% of the amount of glutamate biocoating obtained in water was obtained in blood plasma. Albumin did not prevent the formation of a glutamate biocoating. It was shown that the glutamate biocoating is a temporal dynamic structure at the surface of γ-Fe2O3 nanoparticles. Also, components of the nerve terminal incubation medium and physiological fluids responsible for the desorption of glutamate were identified. Glutamate-coated γ-Fe2O3 nanoparticles can be used for glutamate delivery to the nervous system or for glutamate adsorption (but with lower effectiveness) in stroke, brain trauma, epilepsy, and cancer treatment following by its subsequent removal using a magnetic field. γ-Fe2O3 nanoparticles with transient glutamate biocoating can be useful for multifunctional theranostics.

Probiotic Bifunctionality of Bacillus subtilis-Rescuing Lactic Acid Bacteria from Desiccation and Antagonizing Pathogenic Staphylococcus aureus.

Live probiotic bacteria obtained with food are thought to have beneficial effects on a mammalian host, including their ability to reduce intestinal colonization by pathogens. To ensure the beneficial effects, the probiotic cells must survive processing and storage of food, its passage through the upper gastrointestinal tract (GIT), and subsequent chemical ingestion processes until they reach their target organ. However, there is considerable loss of viability of the probiotic bacteria during the drying process, in the acidic conditions of the stomach, and in the high bile concentration in the small intestine. Bacillus subtilis, a spore-forming probiotic bacterium, can effectively maintain a favorable balance of microflora in the GIT. B. subtilis produces a protective extracellular matrix (ECM), which is shared with other probiotic bacteria; thus, it was suggested that this ECM could potentially protect an entire community of probiotic cells against unfavorable environmental conditions. Consequently, a biofilm-based bio-coating system was developed that would enable a mutual growth of B. subtilis with different lactic acid bacteria (LAB) through increasing the ECM production. Results of the study demonstrate a significant increase in the survivability of the bio-coated LAB cells during the desiccation process and passage through the acidic environment. Thus, it provides evidence about the ability of B. subtilis in rescuing the desiccation-sensitive LAB, for instance, Lactobacillus rhamnosus, from complete eradication. Furthermore, this study demonstrates the antagonistic potential of the mutual probiotic system against pathogenic bacteria such as Staphylococcus aureus. The data show that the cells of B. subtilis possess robust anti-biofilm activity against S. aureus through activating the antimicrobial lipopeptide production pathway.

Loading of Antibiotic into Biocoated Hydroxyapatite Nanoparticles: Smart Antitumor Platforms with Regulated Release.

In this research we propose a nanoplatform for anticancer therapy that is based on the combination of three components: (1) an antibiotic to target selectively the mitochondria of cancer cells, inhibiting their functions; (2) mineral nanoparticles (NPs) able to encapsulate the antibiotic and to enter into the cells across the cell membrane; and (3) a biocoating to protect the antibiotic during and/or after its regulated release, increasing its therapeutic efficacy. Chloramphenicol (CAM), a prototypical wide-spectrum antibiotic, has been used to induce mitochondrial-dysfunctions in cancer cells. Different in situ synthetic strategies have been tested to load such antibiotic into both crystalline hydroxyapatite (cHAp) and amorphous calcium phosphate (ACP) NPs. cHAp NPs showed higher loading capacity, in terms of encapsulation and superficial adsorption of CAM, and slower antibiotic release than ACP NPs. On the other hand, the protecting role played by biocoatings based on pyrophosphate and, especially, triphosphate was greater than that of biophosphonates, the anticancer therapeutic efficacy of CAM being maximized by the former. In vitro studies using healthy and cancer cell lines have demonstrated that in situ CAM-loaded cHAp NPs coated with triphosphate selectively kill a great population of cancer cells, evidencing the potential of this nanoplatform in cancer treatment.

The effect of anti-CD133/fucoidan bio-coatings on hemocompatibility and EPC capture.

Surface modification by immobilizing biomolecules has been widely proved to enhance biocompatibility of cardiovascular implanted devices. Here, we aimed at developing a multifunctional surface that not only provides good hemocompatibility but also functions well in capturing circulating endothelial progenitor cells (EPCs) in the blood flow to improve the surface endothelialization. In the present work, we preferred to chemically co-immobilize (Michael addition and Schiff base reaction) the anti-CD133 (EPC-specific antibody) and fucoidan (EPC-mobilization factor, which also contribute to better hemocompatibility) onto a polydopamine (PDA) film which is famous for its stability and endothelial cell (EC) compatibility. The quantality of anti-CD133 and other surface characterization (X-ray photoemission spectroscopy, atomic force microscopy and water contact angle measurement) demonstrated successful preparation of the CD133/fucoidan coating. The platelets adhesion/activation test suggested improved hemocompatibility of this bio-coating. The ex vivo experiment on New Zealand white rabbits showed that the anti-CD133/fucoidan coating had good ability on capture the circulating EPC. In addition, the quartz crystal microbalance-D indicated that the EPC behaviors, including adhesion, spreading and extracellular matrix re-molding, were related to the density of anti-CD133 in the coating. We hope this anti-CD133/fucoidan multi-functional coating may provide potential application on surface modification of cardiovascular biomaterials.

A peptide-based biological coating for enhanced corrosion resistance of titanium alloy biomaterials in chloride-containing fluids.

Titanium alloys are common materials in the manufacturing of dental and orthopedic implants. Although these materials exhibit excellent biocompatibility, corrosion in response to biological fluids can impact prosthesis performance and longevity. In this work, a PEGylated metal binding peptide (D-K122-4-PEG), derived from bacteria Pseudomonas aeruginosa, was applied on a titanium (Ti) alloy, and the corrosion resistance of the coated alloy specimen was investigated in simulated chloride-containing physiological fluids by electrochemical impedance spectroscopy and micro-electrochemical measurements, surface characterization, and biocompatibility testing. Compared to uncoated specimen, the D-K122-4-PEG-coated Ti alloy demonstrates decreased corrosion current density without affecting the natural passivity. Morphological analysis using atomic force microscopy and scanning electron microscopy confirms a reduction in surface roughness of the coated specimens in the fluids. The D-K122-4-PEG does not affect the binding of HEK-293T cells to the surface of unpolished Ti alloy, nor does it increase the leukocyte activation properties of the metal. D-K122-4-PEG represents a promising coating to enhance the corrosion resistance of Ti alloys in physiological fluids, while maintaining an excellent biocompatibility.

Controlling the Biomimetic Implant Interface: Modulating Antimicrobial Activity by Spacer Design.

Surgical site infection is a common cause of post-operative morbidity, often leading to implant loosening, ultimately requiring revision surgery, increased costs and worse surgical outcomes. Since implant failure starts at the implant surface, creating and controlling the bio-material interface will play a critical role in reducing infection while improving host cell-to-implant interaction. Here, we engineered a biomimetic interface based upon a chimeric peptide that incorporates a titanium binding peptide (TiBP) with an antimicrobial peptide (AMP) into a single molecule to direct binding to the implant surface and deliver an antimicrobial activity against S. mutans and S. epidermidis, two bacteria which are linked with clinical implant infections. To optimize antimicrobial activity, we investigated the design of the spacer domain separating the two functional domains of the chimeric peptide. Lengthening and changing the amino acid composition of the spacer resulted in an improvement of minimum inhibitory concentration by a three-fold against S. mutans. Surfaces coated with the chimeric peptide reduced dramatically the number of bacteria, with up to a nine-fold reduction for S. mutans and a 48-fold reduction for S. epidermidis. Ab initio predictions of antimicrobial activity based on structural features were confirmed. Host cell attachment and viability at the biomimetic interface were also improved compared to the untreated implant surface. Biomimetic interfaces formed with this chimeric peptide offer interminable potential by coupling antimicrobial and improved host cell responses to implantable titanium materials, and this peptide based approach can be extended to various biomaterials surfaces.