Highly graphitized coal tar pitch-derived porous carbon as high-performance lithium storage materials.

Because of its high specific capacity and superior rate performance, porous carbon is regarded as a potential anode material for lithium-ion batteries (LIBs). However, porous carbon materials with wide pore diameter distributions suffer from low structural stability and low electrical conductivity during the application process. During this study, the calcium carbonate nanoparticle template method is used to prepare coal tar pitch-derived porous carbon (CTP-X). The coal tar pitch-derived porous carbon has a well-developed macroporous-mesoporous-microporous hierarchical porous network structure, which provides abundant active sites for Li+ storage, significantly reduces polarization and charge transfer resistance, shortens the diffusion path and promotes the rapid transport of Li+. More specifically, the CTP-2 anode shows high charge capacity (496.9 mAh g-1 at 50 mA g-1), excellent rate performance (413.6 mAh g-1 even at 500 mA g-1), and high cycling stability (capacity retention rate of about 100% after 1,000 cycles at 2 A g-1). The clean and eco-friendly large-scale utilization of coal tar pitch will facilitate the development of high-performance anodes in the field of LIBs.

Microfluidic paper-based chemiluminescence sensing platform based on functionalized CaCO3 for time-resolved multiplex detection of avian influenza virus biomarkers.

Multiplex detection can enhance diagnostic precision and improve diagnostic efficiency, providing important assistance for epidemiological investigation and epidemic prevention. There is a great need for multi-detection sensing platforms to accurately diagnose diseases. Herein, we reported a µPAD-based chemiluminescence (CL) assay for ultrasensitive multiplex detection of AIV biomarkers, based on three DNAzyme/Lum/PEI/CaCO3. Three time-resolved CL signals were sequentially generated with detection limits of 0.32, 0.34, and 0.29 pM for H1N1, H7N9, and H5N1, respectively, and with excellent selectivity against interfering DNA. The recovery test in human serum displayed satisfactory analysis capabilities for complex biological samples. The µPAD-based CL assay achieved multiplex detection within 70 s, with a high time resolution of 20 s. The proposed strategy has the advantages of low cost, high sensitivity, good selectivity, and wide time resolution, the µPAD-based CL assay has shown great potential in the early and accurate diagnosis of diseases.

Atmospheric CO2 Sequestration in Seawater Enhanced by Molluscan Shell Powders.

Carbon capture, utilization, and storage (CCUS) are widely recognized as a promising technology for mitigating climate change. CO2 mineralization using Ca-rich fluids and high-concentration CO2 gas has been studied extensively. However, few studies have reported CO2 mineralization with atmospheric CO2, owing to the difficulty associated with its low concentration. In seawater, the biomineralization process promotes Ca accumulation and CaCO3 precipitation, assisted by specific organic matter. In this study, we examined the conversion of atmospheric CO2 into CaCO3 in seawater using shell powders (Pinctada fucata, Haliotis discus, Crassostrea gigas, Mizuhopecten yessoensis, Turbo sazae, and Saxidomus purpurata). Among the six species, the shell powder of S. purpurata showed the highest rate of CaCO3 formation and recovery of CaCO3. NaClO treatment test revealed that the organic matter in the shells enhanced the CO2 mineralization. All materials used in this study, including atmospheric CO2, seawater, and shells, are economically feasible for large-scale applications. Using shell powder for CO2 mineralization in seawater embodies an innovative technological advancement to address climate change.

Effect of (in)organic additives on microbially induced calcium carbonate precipitation.

AIM: This study aimed to understand the morphological effects of (in)organic additives on microbially induced calcium carbonate precipitation (MICP). METHODS AND RESULTS: MICP was monitored in real time in the presence of (in)organic additives: bovine serum albumin (BSA), biofilm surface layer protein A (BslA), magnesium chloride (MgCl2), and poly-l-lysine. This monitoring was carried out using confocal microscopy to observe the formation of CaCO3 from the point of nucleation, in comparison to conditions without additives. Complementary methodologies, namely scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction, were employed to assess the visual morphology, elemental composition, and crystalline structures of CaCO3, respectively, following the crystals' formation. The results demonstrated that in the presence of additives, more CaCO3 crystals were produced at 100 min compared to the reaction without additives. The inclusion of BslA resulted in larger crystals than reactions containing other additives, including MgCl2. BSA induced a significant number of crystals from the early stages of the reaction (20 min) but did not have a substantial impact on crystal size compared to conditions without additives. All additives led to a higher content of calcite compared to vaterite after a 24-h reaction, with the exception of MgCl2, which produced a substantial quantity of magnesium calcite. CONCLUSIONS: The work demonstrates the effect of several (in)organic additives on MICP and sets the stage for further research to understand additive effects on MICP to achieve controlled CaCO3 precipitation.

Synthesis of CaCO3 supported nano zero-valent iron-nickel nanocomposite (nZVI-Ni@CaCO3) and its application for trichloroethylene removal in persulfate activated system.

Nano zero-valent (nZVI) based composite have been widely utilized in environmental remediation. However, the rapid agglomeration and quick deactivation of nZVI limited its application on large scale. In this work, CaCO3 supported nZVI-Ni catalyst, namely nZVI-Ni@CaCO3 was prepared and used for the efficient removal of trichloroethylene (TCE) in PS oxidation process. The successful disbursement of nZVI-Ni on CaCO3 support material not only increased the surface area of nZVI-Ni@CaCO3 (69.45 m2/g) with respect to CaCO3 (5.92 m2/g) and bare nZVI (13.29 m2/g) but also improved the catalytic activity. XRD, XPS and FTIR analysis confirmed the successful formation of nZVI-Ni@CaCO3 nanoparticles. The nZVI-Ni@CaCO3 nanoparticles combined with PS had achieved complete removal of TCE (99.8%) with dosage of 36 mg/L and 1.34 mM respectively. These results showed that the use of CaCO3 as support material for nZVI-Ni could have significant influence on contaminant removal process. Scavenging and EPR tests validated the existence of SO4•-, OH• and O2•- radicals in PS/nZVI-Ni@CaCO3 system and highlighted the dominant role of SO4•- radicals in TCE removal process. HCO3- ions and humic acid have shown adverse effect on TCE removal due to radical scavenging and buffering effect. Owing to improved catalytic activity and easy preparation, the nZVI-Ni@CaCO3 nanoparticles could be served as an alternative strategy for environmental remediation.

The effects of impurities in carbide slag on the morphological evolution of CaCO3 during carbonation.

Carbide slag (CS) is a kind of solid waste generated by the hydrolysis of calcium carbide for acetylene production. Its major component is Ca(OH)2, which shows great potential in CO2 mineralization to produce CaCO3. However, the types of impurities in CS and their mechanisms for inducing the morphological evolution of CaCO3 are still unclear. In this work, the influence of impurities in CS on the morphology evolution of CaCO3 was investigated. The following impurities were identified in the CS: Al2O3, MgO, Fe2O3, SiO2 and CaCO3. Ca(OH)2 was used to study the influence of impurities (Al2O3 and Fe2O3) on the evolution of CaCO3 morphology during CS carbonation. Calcite (CaCO3) was the carbonation product produced during CS carbonation under varying conditions. The morphology of calcite was changed from cubic to rod-shaped, with increasing solid-liquid ratios. Moreover, rod-shaped calcite was converted into irregular particles with increasing CO2 flow rate and stirring speed. Rod-shaped calcite (CaCO3) was formed by CS carbonation at a solid-liquid ratio of 10:100 under a stirring speed of 600 rpm and a CO2 flow rate of 200 ml/min; and spherical calcite was generated during Ca(OH)2 carbonation under the same conditions. Al2O3 impurities had negligible effects on spherical CaCO3 during Ca(OH)2 carbonation. In contrast, rod-shaped CaCO3 was generated by adding 0.13 wt% Fe2O3 particles, similar to the content of Fe2O3 in CS. Rod-shaped calcite was converted into particulate calcite with increasing Fe2O3 content. The surface wettability and surface negative charge of Fe2O3 appeared to be responsible for the formation of rod-shaped CaCO3. This study enhances our understanding and utilization of CS and CO2 reduction and the fabrication of high-value rod-shaped CaCO3.

Innovative methodology for comprehensive utilization of arsenic-bearing neutralization sludge.

Arsenic-bearing neutralization (ABN) sludge is a classical hazardous waste commonly found in nonferrous metallurgy. However, the current storage of these hazardous wastes not only has to pay costly hazardous waste taxes but also poses significant risks to both the environment and human health. To address these issues and achieve the comprehensive utilization and minimization of ABN sludge, this study proposes a new combined process. The process involves selective reduction roasting, leaching, and carbonation, through which, the arsenate and gypsum in the ABN sludge were recovered in the form of As(s), high-purity CaCO3, and H2S. The selective reduction behaviors of arsenate and gypsum were investigated through thermodynamic analysis and roasting experiments. The results indicated that the 95.35 % arsenate and 96.55 % gypsum in the sludge were selectively reduced to As4(g) and CaS at 950 °C by carbothermic reduction. The As4(g) was condensed to As(s) and enriched in the dust (As, 96.78 wt %). In the leaching process, H2S gas was adopted to promote the leaching of CaS, and resulted in 97.41 % of CaS in the roasted product was selectively leached in the form of Ca(HS)2, leading to a 74.11 % reduction in the weight of the ABN sludge. Then, the Ca(HS)2 was subjected to capture CO2 for the separation of Ca2+ and S2-. The result depicted that 99.69 % of Ca2+ and 99.12 % of S2- were separated as high-purity (99.12 wt %) CaCO3 and H2S (24.89 vol %) by controlling the terminal carbonation pH to below 6.55. The generated H2S can be economically converted to sulfur by the Clause process. The whole process realized the comprehensive resource recovery and the minimization of the sludge, which provides an alternative solution for the clean treatment of hazardous ABN waste.

Ultrasonic Preparation of Nano-CaCO3 Templates and Hollow Mesoporous SiO2 Nanoparticles for Voriconazole Loading.

CaCO3 nanoparticles (nano-CaCO3) as nano-templates were prepared using CaCl2 and Na2CO3 solutions under controlled sonication (19.5 kHz). Using the same ultrasonic device, subsequently, hollow mesoporous silica nanoparticles (HMSNs) were obtained by the hard template of nano-CaCO3. HMSNs were selected as carriers for the antifungal drug voriconazole (VOR) loading to overcome poor water solubility. Three-dimensional CaCO3 nanosheets HMSNs were obtained under gentle sonication. Three-dimensional CaCO3 nanosheets of 24.5 nm (hydrodynamic diameter) were obtained under 17.6 W for 3 min. HMSNs were synthesized by double-template method with nano-CaCO3 as the hard template. Transmission electron microscopy measurements showed that the prepared HMSNs possess hollow structures with particle size between 110 and 120 nm. Nitrogen physisorption at -196 °C revealed that the HMSNs had high surface area (401.57 m2/g), high pore volume (0.11 cm3/g), and uniform pore size (2.22 nm) that facilitated the effective encapsulation of VOR in the HMSNs. The loading capacity of VOR (wt%) on the HMSNs was 7.96%, and the total VOR release amount of VOR-HMSNs material was 71.40% at 480 min. The kinetic model confirmed that the release mechanism of HMSNs nanoparticles followed Fickian diffusion at pH = 7.4 and 37 °C. Moreover, the cumulative VOR release at 42 °C (86.05%) was higher than that at 37 °C (71.40%). The cumulative release amount of VOR from the VOR-HMSNs material was 92.37% at pH = 5.8 at the same temperature. Both nano-CaCO3 templates and HMSNs were prepared by sonication at 19.5 kHz. The as-prepared HMSNs can effectively encapsulate VOR and released drug by Fickian diffusion.

Exploring the use of clay pots as sustainable storage containers to improve water quality.

BACKGROUND: Currently, tap water consumption is not highly preferred in Egypt and around the world. People prefer to consume bottled water because they believe that it is much safer and tastes better than tap water. Unfortunately, this preference can create an economic burden for many people, especially in developing countries. Clay pots can be used to provide cool, alkaline drinking water because of their porous micro-texture, which traps pollutants. This study aimed to investigate the use of clay pots to store tap water and its impact on the requirements for drinking water quality. This is done with the intent to decrease the need for bottled water as a means of offering a more sustainable and economical option. METHODS: In this study, the efficiency of clay pots as sustainable storage containers for drinking water was tested by measuring physicochemical parameters (pH, TDS, EC, turbidity, DO, ammonia, chloride, total hardness, Ca hardness, Mg hardness, chlorine, Zn, and CaCO3) and biological parameters (TPC and Legionella). RESULTS: After 7 days of storage, the quality of the water stored in clay pots met the standards set by the Egyptian law with a significant difference (p < 0.05) before and after the storage of water It was found that the dissolved oxygen increased from 6.17 ppm to 7.52 ppm after 7 days. As for total hardness, it declined from 195 to 178 ppm. There was also a significant drop in terms of TDS from 338 to 275 ppm. Furthermore, clay pots effectively filtered out both total viable bacteria and Legionella. CONCLUSION: This study proved the efficiency of using these containers with respect to some indicator values for tap water and tank water analysis. Clay pots are an excellent, cost-effective, and sustainable alternative for storing water.

Regenerative marine waste towards CaCO3 nanoformulation for Alzheimer's therapy.

Alzheimer's disorder (AD) is associated with behavioural and cognitive destruction with due respect to the neurological degeneration. Conventional therapeutic approach for treatment of AD using neuroprotective drugs suffered certain limitations such as poor solubility, insufficient bioavailability, adverse side effects at higher dose and ineffective permeability on blood brain barrier (BBB). Development of nanomaterial based drug delivery system helped to overcome these barriers. Hence the present work focused on encapsulating neuroprotective drug citronellyl acetate within CaCO3 nanoparticles to develop neuroprotective CaCO3 nanoformulation (CA@CaCO3 NFs). CaCO3 was derived from marine conch shell waste, while the neuroprotective drug citronellyl acetate was scrutinized by in-silico high throughput screening. In-vitro findings revealed that CA@CaCO3 nanoformulation exhibited enhanced free radical scavenging activity of 92% (IC50 value - 29.27 ± 2.6 µg/ml), AChE inhibition of 95% (IC50 value - 25.6292 ± 1.5 µg/ml) at its maximum dose (100 µg/ml). CA@CaCO3 NFs attenuated the aggregation of ß-amyloid peptide (Aß) and also disaggregated the preformed mature plaques the major risk factor for AD. Overall, the present study reveals that CaCO3 nanoformulations exhibits potent neuroprotective potential when compared to the CaCO3 nanoparticles alone and citronellyl acetate alone due to the sustained drug release and synergistic effect of CaCO3 nanoparticles and citronellyl acetate depicting the fact that CaCO3 can act as promising drug delivery system for treatment of neurodegenerative and CNS related disorders.

Sodium citrate increases the aggregation capacity of calcium ions during microbial mineralization to accelerate the formation of calcium carbonate.

The microbially induced carbonate precipitation (MICP) technique is widely used in soil heavy metal pollution control. Microbial mineralization involves extended mineralization times and slow crystallization rates. Thus, it is important to discover a method to accelerate mineralization. In this study, we selected six nucleating agents to screen and investigated the mineralization mechanism using polarized light microscopy, scanning electron microscopy, X-ray diffraction and Fourier-transform infrared spectroscopy. The results showed that sodium citrate removed 90.1% Pb better than traditional MICP and generated the highest amount of precipitation. Interestingly, due to the addition of sodium citrate (NaCit), the rate of crystallization increased and vaterite was stabilized. Moreover, we constructed a possible model to explain that NaCit increases the aggregation capacity of calcium ions during microbial mineralization to accelerate the formation of calcium carbonate (CaCO3). Thus, sodium citrate can increase the rate of MICP bioremediation, which is important for improving MICP efficiency.

Optimization of deposition process for a productive and cohesive bio-CaCO3 to repair concrete existing cracks.

Microbial-induced carbonate precipitation (MICP) is being investigated to repair concrete cracks because of its good durability and compatibility with cementitious matrix. However, during the in-situ application, the repairing often lasts weeks, even months. And the strength regain is quite low. The repairing time is largely determined by the CaCO3 yield, and the strength regain after the repair is closely related to the cohesion and bonding strength of CaCO3 itself. Thus, the purpose of this paper is to obtain an efficient precipitation of bio-CaCO3 with both high yield and good cohesion to improve the in-situ repairing efficiency. Firstly, the most influential factors on urease activity were screened and the precipitation kinetics were detailly investigated. The results show that the CaCO3 with the largest yield and cohesion was obtained when the bacterial concentration was 107 cells/mL and the concentration of urea and calcium was both 0.5 M at 20 °C. This weight loss of bio-CaCO3 was 9.24% under ultrasonic attack. Secondly, two models were established to quantify or semi-quantify the relationship between the most influential factors and the yield and cohesion of precipitates, respectively. The results showed the order of contribution for bio-CaCO3 precipitation was calcium ions concentration > bacterial concentration > urea concentration > temperature > initial pH. According to these models, the required yield and cohesion of CaCO3 by engineering could be obtained by adjusting affecting factors. Models were proposed for guiding the application of MICP in practical engineering. KEY POINTS: • Screened the most affecting factors on urease activity and investigated the precipitation kinetics. • Obtained optimal conditions of bio-CaCO. • Established two models in order to give some guidance for practical civil engineering.

CaCO3 powder-mediated biomineralization of antigen nanosponges synergize with PD-1 blockade to potentiate anti-tumor immunity.

Antigen self-assembly nanovaccines advance the minimalist design of therapeutic cancer vaccines, but the issue of inefficient cross-presentation has not yet been fully addressed. Herein, we report a unique approach by combining the concepts of "antigen multi-copy display" and "calcium carbonate (CaCO3) biomineralization" to increase cross-presentation. Based on this strategy, we successfully construct sub-100 nm biomineralized antigen nanosponges (BANSs) with high CaCO3 loading (38.13 wt%) and antigen density (61.87%). BANSs can be effectively uptaken by immature antigen-presenting cells (APCs) in the lymph node upon subcutaneous injection. Achieving efficient spatiotemporal coordination of antigen cross-presentation and immune effects, BANSs induce the production of CD4+ T helper cells and cytotoxic T lymphocytes, resulting in effective tumor growth inhibition. BANSs combined with anti-PD-1 antibodies synergistically enhance anti-tumor immunity and reverse the tumor immunosuppressive microenvironment. Overall, this CaCO3 powder-mediated biomineralization of antigen nanosponges offer a robust and safe strategy for cancer immunotherapy.

Biomass-Derived Anion-Anchoring Nano-CaCO3 Coating for Regulating Ion Transport on Li Metal Surface.

The free transport of anions in a Li metal battery can cause multiple issues, including a high anion transference number, space charge, and concentration polarization, eventually leading to uncontrolled dendrite formation and decreased performance. Herein, we report an anion-anchoring nano-CaCO3 (NC) coating derived from eggshell biowaste for stabilizing Li metal anodes. As the adsorption of local TFSI- anions onto the NC adsorbent can undermine the anion concentration gradient and promote rapid Li-ion diffusion, it can effectively inhibit the proliferation of Li dendrites assisted by the NC coating. Consequently, Li/Cu cells with NC@Cu electrode can achieve a high Coulombic efficiency of ∼98.4% for more than 420 cycles and can even reach ∼99.1% at an ultrahigh areal capacity of 20 mAh cm-2. In particular, full cells with NC/Li@Cu electrodes show a stable lifespan of over 240 cycles with an average efficiency of ∼99.8% at a low N/P ratio of ∼3.3.

Determination of Phenol with Peroxidase Immobilized on CaCO3.

Phenols are widely used in industries despite their toxicity, which requires governments to limit their concentration in water to 5 mg/L before discharge to the city sewer. Thus, it is essential to develop a rapid, simple, and low-cost detection method for phenol. This study explored two pathways of peroxidase immobilization to develop a phenol detection system: peroxidase encapsulation into polyelectrolyte microcapsules and peroxidase captured by CaCO3. The encapsulation of peroxidase decreased enzyme activity by 96%; thus, this method cannot be used for detection systems. The capturing process of peroxidase by CaCO3 microspherulites did not affect the maximum reaction rate and the Michaelis constant of peroxidase. The native peroxidase-Vmax = 109 µM/min, Km = 994 µM; CaCO3-peroxidase-Vmax = 93.5 µM/min, Km = 956 µM. Ultimately, a reusable phenol detection system based on CaCO3 microparticles with immobilized peroxidase was developed, capable of detecting phenol in the range of 700 ng/mL to 14 µg/mL, with an error not exceeding 5%, and having a relatively low cost and production time. The efficiency of the system was confirmed by determining the content of phenol in a paintwork product.

Fabrication of Ag-CaCO3 Nanocomposites for SERS Detection of Forchlorfenuron.

In this study, Ag-CaCO3 nanocomposites were synthesized using silver nitrate as the precursor solution based on calcium carbonate nanoparticles (CaCO3 NPs). The synthesis involved the reaction of calcium lignosulphonate and sodium bicarbonate. The properties of Ag-CaCO3 nanocomposites were studied by various technologies, including an ultraviolet-visible spectrophotometer, a transmission electron microscope, and a Raman spectrometer. The results showed that Ag-CaCO3 nanocomposites exhibited a maximum UV absorption peak at 430 nm, the surface-enhanced Raman spectroscopy (SERS) activity of Ag-CaCO3 nanocomposites was evaluated using mercaptobenzoic acid (MBA) as the marker molecule, resulting in an enhancement factor of 6.5 × 104. Additionally, Ag-CaCO3 nanocomposites were utilized for the detection of forchlorfenuron. The results demonstrated a linear relationship in the concentration range of 0.01 mg/mL to 2 mg/mL, described by the equation y = 290.02x + 1598.8. The correlation coefficient was calculated to be 0.9772, and the limit of detection (LOD) was determined to be 0.001 mg/mL. These findings highlight the relatively high SERS activity of Ag-CaCO3 nanocomposites, making them suitable for analyzing pesticide residues and detecting toxic and harmful molecules, thereby contributing to environmental protection.

The response surface methodology for optimization of Halomonas sp. C2SS100 lipase immobilization onto CaCO3 for treatment of tuna wash processing wastewater.

An immobilized enzyme could exhibit selectively modified physicochemical properties, and it might offer a better environment for the enzyme activity. In this study, the immobilization yield of crude Halomonas sp. lipase was optimized to improve its stability. Thanks to its high adsorption capacity, CaCO3 has been chosen as support for the immobilization process. Furthermore, response surface methodology (RSM) was used to determine optimal conditions for the immobilization of the bacterial lipase. Five tested factors (enzyme solution, support amount, time, temperature, and acetone volume) were optimized applying a central composite design of RSM. The maximum yield of lipase immobilization was improved to 96%. Furthermore, a biochemical characterization proved a significant improvement of the immobilized lipase stability. The immobilized enzyme is more stable at extreme pH values and high temperatures than the free one. We also tested the reusability of the immobilized lipase by evaluating the recovery of the support using simple filtration. Thanks to its high stability, the immobilized lipase was invested in an effective treatment of tuna wash processing wastewater. The oil biodegradation efficiency was established at 81.5% and was confirmed by Fourier transformation infrared spectrometry. Likewise, the biological oxygen demand values were reduced which makes a possible reduction of the wastewater pollution degree.

Structural changes and calcium bioaccessibility of calcium fortified milk containing CaCO3 loaded solid-in-oil-in-water emulsion during simulated in vitro digestion.

BACKGROUND: In most regions around the globe, average dietary calcium intake is relatively low. Consumers increasingly supplement calcium with milk. However, commercial high-calcium milk has the problem of low calcium bioaccessibility. This study was to explore calcium fortified milk containing calcium carbonate (CaCO3 ) loaded solid-in-oil-in-water emulsion as a potential novel calcium fortified milk with higher calcium bioaccessibility. RESULTS: The CaCO3 loaded solid-in-oil-in-water (S/O/W) emulsion with good physical stability (zeta potential -33.34 ± 0.96 mV, mean particle size 4.49 ± 0.02 µm) and high calcium bioaccessibility (32.34%) was prepared when the concentration of xanthan gum was 4 g L-1 . Furthermore, the physicochemical properties and gastrointestinal fate of calcium fortified milk (calcium contents, 1.25 mg mL-1 , 1.35 mg mL-1 , and 1.45 mg mL-1 ) with different proportions of CaCO3 loaded S/O/W emulsion and pure milk were investigated. The calcium fortified milk (calcium content, 1.25 mg mL-1 ) with a small amount of CaCO3 loaded S/O/W emulsion did not significantly affect the physicochemical properties of pure milk and had similar rheological properties and higher calcium bioaccessibility to commercial high-calcium milk. Excessive calcium ion (Ca2+ ) weakens the electrostatic interaction of milk sample system and causes aggregation of colloidal particles, which was attributed to more insoluble calcium soap formation. CONCLUSION: This study showed that the S/O/W emulsion delivery system improved the dispersion stability and bioaccessibility of CaCO3 . These findings contribute to the development of calcium fortified milk with improved physicochemical properties and higher calcium bioaccessibility. © 2023 Society of Chemical Industry.

Tumor Microenvironment-Responsive Cu/CaCO3 -Based Nanoregulator for Mitochondrial Homeostasis Disruption-Enhanced Chemodynamic/Sonodynamic Therapy.

The efficiency of reactive oxygen species (ROS)-mediated cancer therapy is restrained by intrinsic characteristics in the tumor microenvironment (TME), such as overexpressed glutathione (GSH), hypoxia and limited efficiency of H2 O2 . In this work, intelligent copper-dropped calcium carbonate loading sonosensitizer Ce6 nanoparticles (Cu/CaCO3 @Ce6, CCC NPs) are established to realize TME-responsive self-supply of oxygen and successively Ca2+ -overloading-strengthened chemodynamic therapy/sonodynamic therapy (CDT/SDT). CCC NPs release Ca2+ , Cu2+ , and Ce6 in weakly acid and GSH-excessive TME. Released Cu2+ can not only consume GSH and turn into Cu+ via a redox reaction, but also provide CDT-creating hydroxyl radicals through the Fenton-like reaction. Under ultrasound irradiation, the intracellular oxidative stress is amplified profoundly relying on singlet oxygen outburst from SDT. Moreover, Ca2+ influx aggravates the mitochondrial disruption, which further accelerates the oxidation level. The facile and feasible design of the Cu-dropped CaCO3 -based nanoregulators will be further developed as a paradigm in ROS-contributed cancer therapy.

Biosequestration of carbon dioxide using carbonic anhydrase from novel Streptomyces kunmingensis.

The increase in the atmospheric concentrations of carbon dioxide due to anthropogenic interventions has led to several undesirable consequences, notably global warming and related changes. Avoidance of and/or removal of carbon dioxide will result in the reduction of global warming. Biosequestration of carbon by using carbonic anhydrase (CA) as biocatalyst is one of most effective approaches. In the present study, actinobacterial cultures isolated from bamboo (Bambusa vulgaris) rhizosphere were screened for the production of carbonic anhydrase enzyme. The strain BS19 which showed promising CA production was selected as the potential strain. Strain BS19 was identified as Streptomyces kunmingensis based on the phenotypic and molecular characteristics. In submerged fermentation, strain BS19 produced 214.21 IU/ml of CA enzyme. The molecular mass of the CA was determined as 45 ± 2 kDa. The production of CA was found to be optimal at pH 7.0 and at temperature of 28 °C. The full length periplasmic CA gene was successfully amplified from S. kunmingensis BS19. Biomimetic sequestration of carbon was detected and quantified through CaCO3 precipitation method. Further, the CA of BS 19 was successfully used to mineralize CO2 present in motorbike exhaust, which has a similar composition to that of flue gas. The well-defined rhombohedral calcite crystals formed in the mineral carbonation reaction was observed through SEM analysis. The findings of this study clearly indicated that Streptomyces kunmingensis BS19 isolated from bamboo rhizosphere is a promising candidate for the production of carbonic anhydrase which deserves the potential for CO2 sequestration.