Electrical current modulation in wood electrochemical transistor.

The nature of mass transport in plants has recently inspired the development of low-cost and sustainable wood-based electronics. Herein, we report a wood electrochemical transistor (WECT) where all three electrodes are fully made of conductive wood (CW). The CW is prepared using a two-step strategy of wood delignification followed by wood amalgamation with a mixed electron-ion conducting polymer, poly(3,4-ethylenedioxythiophene)-polystyrene sulfonate (PEDOT:PSS). The modified wood has an electrical conductivity of up to 69 Sm-1 induced by the formation of PEDOT:PSS microstructures inside the wood 3D scaffold. CW is then used to fabricate the WECT, which is capable of modulating an electrical current in a porous and thick transistor channel (1 mm) with an on/off ratio of 50. The device shows a good response to gate voltage modulation and exhibits dynamic switching properties similar to those of an organic electrochemical transistor. This wood-based device and the proposed working principle demonstrate the possibility to incorporate active electronic functionality into the wood, suggesting different types of bio-based electronic devices.

Stretchable Electrodes for Interconnects in Soft Electronics.

Soft electronics have significantly enhanced user convenience and data accuracy in wearable devices, implantable devices, and human-machine interfaces. However, a persistent challenge in their development has been the disconnection between the rigid and soft components of devices due to the substantial difference in modulus and stretchability. To address this issue, establishing a durable and flexible connection that smoothly links components of varying stiffness to signal-capturing sections with a lower stiffness is essential. In this study, we developed a novel stretchable interconnect that strongly adheres to various materials, facilitating electrical connections effortlessly by applying minimal finger pressure. Capable of stretching up to 1000% while maintaining electrical integrity, this interconnect proves its applicability across multiple domains, including electrocardiogram (ECG), electromyography (EMG), and stretchable light-emitting diode (LED) circuits. Its versatility is further demonstrated through its compatibility with various manufacturing techniques such as 3D printing, painting, and spin coating, highlighting its adaptability in soft electronics.

Involvement of expanded cytotoxic and proinflammatory CD28null T cells in primary Sjögren's syndrome.

OBJECTIVE: The absence of CD28 is a feature of antigen-experienced, highly differentiated and aged T cells. The pathogenicity of CD28null T cells remains elusive in primary Sjögren's syndrome (pSS). Therefore, this study was performed to explore the characteristics of CD28null T cells in both peripheral blood and minor salivary glands (MSGs) of pSS patients. METHODS: pSS patients and paired healthy controls (HCs) were enrolled. The phenotype of peripheral CD28null T cells was analyzed using flow cytometry. In vitro functional assays were performed to evaluate the cytotoxic and proinflammatory effects of peripheral CD28null T cells. In addition, polychromatic immunofluorescence staining was performed to investigate infiltrating CD28null T cells in MSGs. RESULTS: A significant expansion of peripheral CD28null T cells was observed in pSS patients compared with HCs (p < 0.001), which were primarily CD8+CD28null T cells. The proportion of peripheral CD8+CD28null T cells moderately correlated with the erythrocyte sedimentation rate (r = 0.57, p < 0.01) and IgG levels (r = 0.44, p < 0.01). Peripheral CD28null T cells had stronger capacities to secrete granzyme B and perforin, but comparable capacities to secrete IFN-γ and TNF-α than their CD28+ counterparts. An abundant amount of cytotoxic and pro-inflammatory CD28null T cells was also found in MSGs. Moreover, a high expression of the chemokine receptor CXCR3 was found on peripheral and tissue-resident CD28null T cells, with its ligands CXCL9/10 abundantly present in MSGs. CONCLUSION: Increasing CD28null T cells with strong cytotoxicity and proinflammatory effects were observed in both peripheral blood and MSGs from pSS patients. The precise mechanism of action and migration still needs further investigation.

Multi-Functional PEDOT:PSS as the Efficient Perovskite Solar Cells.

Poly(3,4-ethylenedioxythiophene) (PEDOT), particularly in its complex form with poly(styrene sulfonate) (PEDOT:PSS), stands out as a prominent example of an organic conductor. Renowned for its exceptional conductivity, substantial light transmissibility, water processability, and remarkable flexibility, PEDOT:PSS has earned its reputation as a leading conductive polymer. This study explores the unique effects of two additives, Bisphenol A diglycidyl ether (DGEBA) and Dimethyl sulfoxide (DMSO), on the PSS component of PEDOT:PSS films are shown. Both additives induce grain size growth, while DGEBA makes the PEDOT:PSS layer hydrophobic, which acts as a passivation to protect the perovskite layer, which is vulnerable to moisture. The other additive, DMSO, separates the PSS groups, resulting in increased conductivity through the free movement of holes. With these multi-modified p-type PEDOT:PSS, the ITO/M-PEDOT:PSS/Perovskite/PCBM/Ag structured reverse structure solar cell has improved the power conversion efficiency (PCE) from 15.28% to 17.80% compared to the control cell with conventional PEDOT:PSS. It also maintains 90% for 500 h at 60 °C and 300 h at 1 sun illuminating conditions.

Tuning Hole Transport Properties and Perovskite Crystallization via Pyridine-Based Molecules for Quasi-2D Perovskite Solar Cells.

Quasi-2D perovskites show great potential as photovoltaic devices with superior stability, but the power conversion efficiency (PCE) is limited by poor carrier transport. Here, it is simultaneously affected the hole transport layer (HTL) and the perovskite layer by incorporating pyridine-based materials into poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) to address the key problem above in 2D perovskites. With this approach, the enhanced optoelectronic performance of the novel PEDOT:PSS is due to electron transfer between the additives and PEDOT or PSS, as well as a dissociation between PEDOT and PSS based on experimental and theoretical studies, which facilitates the charge extraction and transfer. Concurrently, in-situ X-ray scattering studies reveal that the introduction of pyridine-based molecules alters the transformation process of the perovskite intermediate phase, which leads to a preferred orientation and ordered distribution caused by the Pb─N chemical bridge, achieving efficient charge transport. As a result, the pyridine-treated devices achieve an increased short-circuit current density (Jsc) and PCE of over 17%.

Humidity-Induced Protein-Based Artificial Synaptic Devices for Neuroprosthetic Applications.

Neuroprosthetics and brain-machine interfaces are immensely beneficial for people with neurological disabilities, and the future generation of neural repair systems will utilize neuromorphic devices for the advantages of energy efficiency and real-time performance abilities. Conventional synaptic devices are not compatible to work in such conditions. The cerebrospinal fluid (CSF) in the central part of the nervous system is composed of 99% water. Therefore, artificial synaptic devices, which are the fundamental component of neuromorphic devices, should resemble biological nerves while being biocompatible, and functional in high-humidity environments with higher functional stability for real-time applications in the human body. In this work, artificial synaptic devices are fabricated based on gelatin-PEDOT: PSS composite as an active material to work more effectively in a highly humid environment (≈90% relative humidity). These devices successfully mimic various synaptic properties by the continuous variation of conductance, like, excitatory/inhibitory post-synaptic current(EPSC/IPSC), paired-pulse facilitation/depression(PPF/PPD), spike-voltage dependent plasticity (SVDP), spike-duration dependent plasticity (SDDP), and spike-rate dependent plasticity (SRDP) in environments at a relative humidity levels of ≈90%.

Elevated unphosphorylated STAT1 and IRF9 in T and B cells of primary sjögren's syndrome: Novel biomarkers for disease activity and subsets.

OBJECTIVES: Autoreactive B cells and interferon (IFN) signature are hallmarks of primary sjögren's syndrome (pSS), but how IFN signaling pathways influence autoantibody production and clinical manifestations remain unclear. More detailed studies hold promise for improved diagnostic methodologies and personalized treatment. METHODS: We analyzed peripheral blood T and B cell subsets from 34 pSS patients and 38 healthy donors (HDs) at baseline and upon stimulation regarding their expression levels of type I and II IFN signaling molecules (STAT1/2, IRF1, IRF9). Additionally, we investigated how the levels of these molecules correlated with serological and clinical characteristics and performed ROC analysis. RESULTS: Patients showed elevated IFN pathway molecules, including STAT1, STAT2 and IRF9 among most T and B cell subsets. We found a reduced ratio of phosphorylated STAT1 and STAT2 in patients in comparison to HDs, although B cells from patients were highly responsive by increased phosphorylation upon IFN stimulation. Correlation matrices showed further interrelations between STAT1, IRF1 and IRF9 in pSS. Levels of STAT1 and IRF9 in T and B cells correlated with the IFN type I marker Siglec-1 (CD169) on monocytes. High levels of STAT1 and IRF9 within pSS B cells were significantly associated with hypergammaglobulinemia as well as anti-SSA/anti-SSB autoantibodies. Elevated STAT1 levels were found in patients with extraglandular disease and could serve as a biomarker for this subgroup (p < 0.01). Notably, IRF9 levels in T and B cells correlated with EULAR Sjögren's syndrome disease activity index (ESSDAI). CONCLUSION: Here, we provide evidence that in active pSS patients, enhanced IFN signaling incl. unphosphorylated STAT1 and STAT2 with IRFs entertain chronic T and B cell activation. Furthermore, increased STAT1 levels candidate as biomarker of extraglandular disease, while IRF9 levels can serve as biomarker for disease activity.

Does depressurization of the portal vein before liver transplantation affect the recurrence of HCC? A nested case-control study.

BACKGROUND: Portal hypertension (PHT) has been proven to be closely related to the development of hepatocellular carcinoma (HCC). Whether PHT before liver transplantation (LT) will affect the recurrence of HCC is not clear. METHODS: 110 patients with depressurization of the portal vein (DPV) operations (Transjugular Intrahepatic Portosystemic Shunt-TIPS, surgical portosystemic shunt or/and splenectomy) before LT from a HCC LT cohort, matched with 330 preoperative non-DPV patients; this constituted a nested case-control study. Subgroup analysis was based on the order of DPV before or after the occurrence of HCC. RESULTS: The incidence of acute kidney injury and intra-abdominal bleeding after LT in the DPV group was significantly higher than that in non-DPV group. The 5-year survival rates in the DPV and non-DPV group were 83.4% and 82.7% respectively (P = 0.930). In subgroup analysis, patients in the DPV prior to HCC subgroup may have a lower recurrence rate (4.7% vs.16.8%, P = 0.045) and a higher tumor free survival rate (88.9% vs.74.4%, P = 0.044) after LT under the up-to-date TNMI-II stage, while in TNM III stage, there was no difference for DPV prior to HCC subgroup compared with the DPV after HCC subgroup or the non-DPV group. CONCLUSION: Compared with DPV after HCC, DPV treatment before HCC can reduce the recurrence rate of HCC after early transplantation (TNM I-II). DPV before LT can reduce the recurrence of early HCC.

Thermoelectric Performance of Hybrid Inorganic/Organic Composites Based on PEDOT:PSS/Tin(II) Oxide.

PEDOT: PSS(poly(3,4-ethylenedioxylthiophene):poly(styrenesulfonate))-based composites often exhibit remarkable characteristics regarding high electrical conductivity and great processability, being a suitable candidate for thermoelectric (TE) applications. To increase its performance, PEDOT:PSS is commonly blended with scarce and toxic inorganic compounds based on Se, Te or Bi. In this work we propose the use of one p-type metal oxide semiconductor (MOs): tin(II) oxide (SnO), motivated by its abundance and low toxicity. Hybrid PEDOT:PSS/SnO composites were obtained by firstly blending Ethylene glycol (EG) with PEDOT:PSS and then by adding p-type SnO, previously synthesized by a chemical route. The mixture was deposited via spin-coating onto glass substrates. The Power Factor (PF) of the composites increased by a factor of 300 with the combined EG/SnO composition.

Spin coated ultrathin PEDOT:PSS/SWCNT film with high electronic conductivity.

Conductive Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been extensively used as non-metallic electrodes. However, the relatively low electrical conductivity of pristine PEDOT:PSS film restricts its further application. Although doping high content conductive filler or increasing the film thickness are effective for enhancing the electrical property, the transparency is sacrificed, which limits the application of PEDOT:PSS films. In this study, preparing PEDOT:PSS composite film with highly conductive and transparent property was the primary purpose. To achieve this goal, single-walled carbon nanotubes (SWCNTs) and dimethyl sulfoxide (DMSO) was chosen to composite with PEDOT:PSS. The spin-coated SWCNT/PEDOT:PSS composite film exhibited excellent electrical conductivity and transparency. The electrical conductivity of composite film with desired transmittance property (78%) reached the highest value (1060.96 S cm-1) at the SWCNTs content was 6 wt%. Under the modification process applied in this work, the non-conductive PSS was partially removed by incorporated DMSO and SWCNTs. Then, the molecular chains of PEDOT stretched and adsorbed onto the surface of SWCNTs, forming a highly efficient three-dimensional conductive structure, which contributed to the enhancement of electrical conductivity and transparency. Additionally, the spin-coating process allowed for the reduction of film thickness, ensuring better transparency. This research contributed to expanding the further applications of PEDOT:PSS films in high-performance transparent film electrodes.

Enhanced Microstructural Uniformity in Sulfuric-Acid-Treated Poly(3,4-Ethylenedioxythiophene):Poly(Styrene Sulfonate) Films Using Raman Map Analysis.

Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films have emerged as potential alternatives to indium-tin oxide as transparent electrodes in optoelectronic devices because of their superior transparency, flexibility, and chemical doping stability. However, pristine PEDOT:PSS films show low conductivities because the insulating PSS-rich domains isolate the conductive PEDOT-rich domains. In this study, the conductivities and corresponding spatially resolved Raman properties of PEDOT:PSS thin films treated with various concentrations of H2SO4 are presented. After the PEDOT:PSS films are treated with the H2SO4 solutions, their electrical conductivities are significantly improved from 0.5 (nontreated) to 4358 S cm-1 (100% v/v). Raman heat maps of the peak shifts and widths of the Cα═Cß stretching mode are constructed. A blueshift and width decrease of the Cα═Cß Raman mode in PEDOT are uniformly observed in the entire measurement area (20 × 20 µm2), indicating that microstructural transitions are successfully accomplished across the area from the coiled to linear conformation and high crystallinity upon H2SO4 treatment. Thus, it is proved that comprehensive Raman map analysis can be easily utilized to clarify microstructural properties distributed in large areas induced by various dopants. These results also offer valuable insights for evaluating and optimizing the performance of other conductive thin films.

PEDOT:PSS-Based Prolonged Long-Term Decay Synaptic OECT with Proton-Permeable Material, Nafion.

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS), a conductive polymer, has gained popularity as the channel layer in organic electrochemical transistors (OECTs) due to its high conductivity and straightforward processing. However, difficulties arise in controlling its conductivity through gate voltage, presenting a challenge. To address this issue, aromatic amidine base, diazabicyclo[4.3.0]non-5-ene (DBN), is used to stabilize the doping state of the PEDOT chain through a reliable chemical de-doping process. Furthermore, the addition of the proton-penetrable material Nafion to the PEDOT:PSS channel layer induces phase separation between the substances. By utilizing a solution containing both PEDOT:PSS and Nafion as the channel layer of OECTs, the efficiency of ion movement into the channel from the electrolyte is enhanced, resulting in improved OECT performance. The inclusion of Nafion in the OECTs' channel layer modifies ion movement dynamics, allowing for the adjustment of synaptic properties such as pulse-paired facilitation, memory level, short-term plasticity, and long-term plasticity. This research aims to introduce new possibilities in the field of neuromorphic computing and contribute to biomimetic technology through the enhancement of electronic component performance.

Citric Acid and Polyvinyl Alcohol Induced PEDOT: PSS with Enhanced Electrical Conductivity and Stretchability for Eco-Friendly, Self-Healable, Wearable Organic Thermoelectrics.

Poly(3,4-ethylenedioxythiophene): poly(styrene sulfonate) (PEDOT: PSS) is a promising material for organic thermoelectric (TE) applications. However, it is challenging to achieve PEDOT: PSS composites with stretchable, self-healable, and high TE performance. Furthermore, some existing self-healing TE materials employ toxic reagents, posing risks to human health and the environment. In this study, a novel intrinsically self-healable and wearable composite is developed by incorporating environmentally friendly, highly biocompatible, and biodegradable materials of polyvinyl alcohol (PVA) and citric acid (CA) into PEDOT: PSS. This results in the formation of double hydrogen bonding networks among CA, PVA, and PEDOT: PSS, inducing microstructure alignment and leading to simultaneous enhancements in both TE performance and stretchability. The resulting composites exhibit a high electrical conductivity and power factor of 259.3 ± 11.7 S·cm-1, 6.9 ± 0.4 µW·m-1·K-2, along with a tensile strain up to 68%. Furthermore, the composites display impressive self-healing ability, with 84% recovery in electrical conductivity and an 85% recovery in tensile strain. Additionally, the temperature and strain sensors based on the PEDOT: PSS/PVA/CA are prepared, which exhibit high resolution suitable for human-machine interaction and wearable devices. This work provides a reliable and robust solution for the development of environmentally friendly, self-healing and wearable TE thermoelectrics.

Fast Visible-Light 3D Printing of Conductive PEDOT:PSS Hydrogels.

Functional inks for light-based 3D printing are actively being searched for being able to exploit all the potentialities of additive manufacturing. Herein, a fast visible-light photopolymerization process is showed of conductive PEDOT:PSS hydrogels. For this purpose, a new Type II photoinitiator system (PIS) based on riboflavin (Rf), triethanolamine (TEA), and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is investigated for the visible light photopolymerization of acrylic monomers. PEDOT:PSS has a dual role by accelerating the photoinitiation process and providing conductivity to the obtained hydrogels. Using this PIS, full monomer conversion is achieved in less than 2 min using visible light. First, the PIS mechanism is studied, proposing that electron transfer between the triplet excited state of the dye (3 Rf*) and the amine (TEA) is catalyzed by PEDOT:PSS. Second, a series of poly(2-hydroxyethyl acrylate)/PEDOT:PSS hydrogels with different compositions are obtained by photopolymerization. The presence of PEDOT:PSS negatively influences the swelling properties of hydrogels, but significantly increases its mechanical modulus and electrical properties. The new PIS is also tested for 3D printing in a commercially available Digital Light Processing (DLP) 3D printer (405 nm wavelength), obtaining high resolution and 500 µm hole size conductive scaffolds.

Pressure to provide milk among mothers of very low birth weight infants: an explorative study.

BACKGROUND: Pump-dependent mothers of very low birth weight (VLBW, < 1500g) infants experience specific challenges achieving sufficient milk supply in the neonatal intensive care unit (NICU) and are therefore less frequently able to achieve (exclusive) breast milk feeding. Stress due to the limitations on participating in the infant's care may contribute to this problem. Some explorative studies suggest that pressure to provide milk may be an additional stressor in mothers. However, the type of pressure to provide milk perceived by mothers of VLBW infants has rarely been examined. METHODS: A retrospective and anonymous questionnaire was conducted with mothers of VLBW infants aged 6 to 24 months at the time of data collection. Quantitative data and written comments were used to examine the mothers' perceptions. Descriptive and bivariate tests (Spearman´s rho, Pearson's chi2) were performed to show correlations between pressure to provide breast milk, parental stress (PSS:NICU: role alteration subscale), milk volume, and maternal factors. Pressure to provide milk was measured through two self-developed single items to differentiate between internal and external pressures. RESULTS: Data of n = 533 mothers of VLBW infants was analysed. More than 70% of the mothers agreed that they pressured themselves to provide milk for their infant. In contrast, 34% of the mothers agreed that they felt pressure from outside to provide milk. Higher milk volume 14 days post-partum was significantly correlated with higher internal (Spearman´s rho = 0.2017, p = 0.000) and higher external pressure to provide milk (Spearman´s rho = 0.2991; p = 0.000). Higher PSS:NICU parental role alteration scores were significantly correlated with more internal (Spearman´s rho = -0.2865, p = 0.000) and more external pressure to provide milk (Spearman´s rho = -0.1478; p = 0.002). Milk volume 14 days post-partum and the PSS:NICU were not significantly correlated (Spearman´s rho = -0.0190; p = 0.701). Qualitative analyses highlighted these results and enhanced the bidirectional relationships between maternal pressure to provide milk and milk volume. CONCLUSIONS: Especially internal pressure to provide milk is perceived by many mothers, being mutually dependent on milk supply and parental stress. Pressure to provide milk may be an important factor to decrease maternal stress in the NICU and, therefore, lead to more positive pumping and breastfeeding experiences. More research and validated instruments are needed to adequately measure pressure to provide milk with its different psychological, social, and environmental dimensions.

Graphdiyne marries PEDOT:PSS to form high-stable heterostructure from 2-unstable components toward ultra-low detection limit of uric acid detection in sweat.

PEDOT: PSS has been used as a biomimetic uric acid (UA) sensor but suffers from unfortunate low detection limit (LOD), narrow detection range and poor stability. Herein, we get graphdiyne (GDY) marry PEDOT:PSS to create a very stable GDY@PEDOT:PSS heterostructure for a biomimetic UA sensor, which accomplishes the lowest LOD (6 nM), the widest detection range (0.03 µM-7 mM) and the longest stability (98.1% for 35 days) among the related UA sensors. The sensor was successfully used to in situ real-time detection of  UA in sweat. The enhancement mechanisms of the sensor were investigated, and results discover that C≡C of GDY and C = C of PEDOT:PSS can cross-link each other by π-π interactions, making not only the former strongly resistant against oxidation deterioration, but also causes the latter to efficiently prevent water swelling of polymer for poor conductivity, thereby leading to high stability from both components. While the stabilized heterostructure can also offer more active sites by enhanced absorption of UA via π-π interactions for highly sensitive detection of UA. This work holds great promise for a practical sweat UA sensor while providing scientific insight to design a stable and electrocatalytically active structure from two unstable components.

Portable electrochemical sensing platform based on amidated GO-MOF and PEDOT:PSS for high-efficient detection of ponceau 4R.

A promising electrochemical sensing platform for the detection of ponceau 4R in food has been fabricated based on the carboxylated graphene oxide (GO-COOH), metal-organic framework (MOF) UIO-66-NH2, and poly (3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). To this end GO-COOH was covalently coupled with UIO-66-NH2 through amide reaction, endowing the material (GO-CONH-UIO-66) unique hierarchical pores and high chemical stability and as a result improving the conductivity of MOF and the dispersion of GO. After the addition of PEDOT:PSS into GO-CONH-UIO-66, the continuity and conductivity of the composite (PEDOT:PSS/GO-CONH-UIO-66) have been further enhanced, due to the high conductivity, favorable film-forming, and hydrophilic properties of PEDOT:PSS. Systematic electrochemical experiments confirm that the PEDOT:PSS/GO-CONH-UIO-66/GCE shows satisfactory electrochemical sensing properties towards the detection of ponceau 4R, with a wide linear detection range of 0.01-30 µM, a low limit of detection of 3.33 nM, and a high sensitivity of 0.606 µA µM-1 cm-2. The PEDOT:PSS/GO-CONH-UIO-66 sensing platform was successfully used to detect ponceau 4R in beverage, and the detection results were compared with  high-performance liquid chromatography. As a result, the PEDOT:PSS/GO-CONH-UIO-66 composite shows a promising application prospect for rapid detection of ponceau 4R in food and will play significant role in food safety detection and supervision.

Iodonium-based pro-adhesive layers for robust adhesion of PEDOT:PSS to surfaces.

Electrochemical grafting of organic molecules to metal surfaces has been well-known as an efficient tool enabling tailored modification of surface at the nanoscale. Among many compounds with the ability to undergo the process of electrografting, iodonium salts belong to less frequently used, especially when compared with the most popular diazonium salts. Meanwhile, due to their increased stability, iodonium salts may be used in situations where the use of diazonium salts is constrained. The aim of this study was to examine the effect of the electrochemical reduction of iodonium salts on the physicochemical properties of Pt electrodes, and the possibility to form pro-adhesive layers facilitating further functionalization purposes. Consequently, we have selected four commercially available iodonium salts (diphenyliodonium chloride, bis(4-tertbutylphenyl)iodonium hexafluorophosphate, (4-nitrophenyl)(2,4,6-trimethylphenyl)iodonium triflate, bis(4-methylphenyl)iodonium hexafluorophosphate), and attached them to the surface of Pt electrodes by means of an electrochemical reduction process. As-formed layers were then extensively characterized in terms of wettability, roughness and charge transfer properties, and used as pro-adhesive coatings prior to the deposition of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate), PEDOT:PSS. Due to the increase in hydrophilicity and roughness, modified electrodes increased the stability of PEDOT:PSS coating while maintaining its high capacitance.

Adhesion and charge transfer between PEDOT:PSS and the surface of the electrode are significantly improved by a simple electrode modification strategy using the electrochemical grafting of commercially available iodonium salts.

Straightforward Production Methods for Diverse Porous PEDOT:PSS Structures and Their Characterization.

Porous conductive polymer structures, in particular Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) structures, are gaining in importance due to their versatile fields of application as sensors, hydrogels, or supercapacitors, to name just a few. Moreover, (porous) conducting polymers have become of interest for wearable and smart textile applications due to their biocompatibility, which enables applications with direct skin contact. Therefore, there is a huge need to investigate distinct, straightforward, and textile-compatible production methods for the fabrication of porous PEDOT:PSS structures. Here, we present novel and uncomplicated approaches to producing diverse porous PEDOT:PSS structures and characterize them thoroughly in terms of porosity, electrical resistance, and their overall appearance. Production methods comprise the incorporation of micro cellulose, the usage of a blowing agent, creating a sponge-like structure, and spraying onto a porous base substrate. This results in the fabrication of various porous structures, ranging from thin and slightly porous to thick and highly porous. Depending on the application, these structures can be modified and integrated into electronic components or wearables to serve as porous electrodes, sensors, or other functional devices.

Novel Conductive Polymer Composite PEDOT:PSS/Bovine Serum Albumin for Microbial Bioelectrochemical Devices.

A novel conductive composite based on PEDOT:PSS, BSA, and Nafion for effective immobilization of acetic acid bacteria on graphite electrodes as part of biosensors and microbial fuel cells has been proposed. It is shown that individual components in the composite do not have a significant negative effect on the catalytic activity of microorganisms during prolonged contact. The values of heterogeneous electron transport constants in the presence of two types of water-soluble mediators were calculated. The use of the composite as part of a microbial biosensor resulted in an electrode operating for more than 140 days. Additional modification of carbon electrodes with nanomaterial allowed to increase the sensitivity to glucose from 1.48 to 2.81 µA × mM-1 × cm-2 without affecting the affinity of bacterial enzyme complexes to the substrate. Cells in the presented composite, as part of a microbial fuel cell based on electrodes from thermally expanded graphite, retained the ability to generate electricity for more than 120 days using glucose solution as well as vegetable extract solutions as carbon sources. The obtained data expand the understanding of the composition of possible matrices for the immobilization of Gluconobacter bacteria and may be useful in the development of biosensors and biofuel cells.