Self-Accelerating Effect in a Covalent-Organic Framework with Imidazole Groups Boosts Electroreduction of CO2 to CO.

Solvent effect plays an important role in catalytic reaction, but there is little research and attention on it in electrochemical CO2 reduction reaction (eCO2 RR). Herein, we report a stable covalent-organic framework (denoted as PcNi-im) with imidazole groups as a new electrocatalyst for eCO2 RR to CO. Interestingly, compared with neutral conditions, PcNi-im not only showed high Faraday efficiency of CO product (≈100 %) under acidic conditions (pH ≈ 1), but also the partial current density was increased from 258 to 320 mA cm-2 . No obvious degradation was observed over 10 hours of continuous operation at the current density of 250 mA cm-2 . The mechanism study shows that the imidazole group on the framework can be protonated to form an imidazole cation in acidic media, hence reducing the surface work function and charge density of the active metal center. As a result, CO poisoning effect is weakened and the key intermediate *COOH is also stabilized, thus accelerating the catalytic reaction rate.

Evaluation of the Flexibility for Catalytic Ozonation of Dichloromethane over Urchin-Like CuMnOx in Flue Gas with Complicated Components.

The evaluation of the poisoning effect of complex components in practical gas on DCM (dichloromethane) catalytic ozonation is of great significance for enhancing the technique's environmental flexibility. Herein, Ca, Pb, As, and NO/SO2 were selected as a typical alkaline-earth metal, heavy metal, metalloid, and acid gas, respectively, to evaluate their interferences on catalytic behaviors and surface properties of an optimized urchin-like CuMn catalyst. Ca/Pb loading weakens the formation of oxygen vacancies, oxygen mobility, and acidity due to the fusion of Mn-Ca/Pb-O, leading to their inferior catalytic performance with poor CO2 selectivity and mineralization rate. Noticeably, the presence of As induces excessively strong acidity, facilitating the inevitable formation of byproducts. Catalytic co-ozonation of NO/DCM is achieved with stoichiometric ozone addition. Unfortunately, SO2 introduction brings irreversible deactivation due to strong competition adsorption and the loss of active sites. Unexpectedly, Ca loading protects active sites from an attack by SO2. The formation of unstable sulfites and the released Mn-O structure offset the negative effect from SO2. Overall, the catalytic ozonation of DCM exhibits a distinctive priority in the antipoisoning of metals with the maintenance of DCM conversion. The construction of more stable acid sites should be the future direction of catalyst design; otherwise, catalytic ozonation should be arranged together with post heavy metal capture and a deacidification system.

Competitive Adsorption: Reducing the Poisoning Effect of Adsorbed Hydroxyl on Ru Single-Atom Site with SnO2 for Efficient Hydrogen Evolution.

Ruthenium (Ru) has been theoretically considered a viable alkaline hydrogen evolution reaction electrocatalyst due to its fast water dissociation kinetics. However, its strong affinity to the adsorbed hydroxyl (OHad ) blocks the active sites, resulting in unsatisfactory performance during the practical HER process. Here, we first reported a competitive adsorption strategy for the construction of SnO2 nanoparticles doped with Ru single-atoms supported on carbon (Ru SAs-SnO2 /C) via atomic galvanic replacement. SnO2 was introduced to regulate the strong interaction between Ru and OHad by the competitive adsorption of OHad between Ru and SnO2 , which alleviated the poisoning of Ru sites. As a consequence, the Ru SAs-SnO2 /C exhibited a low overpotential at 10 mA cm-2 (10 mV) and a low Tafel slope of 25 mV dec-1 . This approach provides a new avenue to modulate the adsorption strength of active sites and intermediates, which paves the way for the development of highly active electrocatalysts.

Free-Standing, Interwoven Tubular Graphene Mesh-Supported Binary AuPt Nanocatalysts: An Innovative and High-Performance Anode Methanol Oxidation Catalyst.

Pt-based alloy or bimetallic anode catalysts have been developed to reduce the carbon monoxide (CO) poisoning effect and the usage of Pt in direct methanol fuel cells (DMFCs), where the second metal plays a role as CO poisoning inhibitor on Pt. Furthermore, better performance in DMFCs can be achieved by improving the catalytic dispersion and using high-performance supporting materials. In this work, we introduced a free-standing, macroscopic, interwoven tubular graphene (TG) mesh as a supporting material because of its high surface area, favorable chemical inertness, and excellent conductivity. Particularly, binary AuPt nanoparticles (NPs) can be easily immobilized on both outer and inner walls of the TG mesh with a highly dispersive distribution by a simple and efficient chemical reduction method. The TG mesh, whose outer and inner walls were decorated with optimized loading of binary AuPt NPs, exhibited a remarkably catalytic performance in DMFCs. Its methanol oxidation reaction (MOR) activity was 10.09 and 2.20 times higher than those of the TG electrodes with only outer wall immobilized with pure Pt NPs and binary AuPt NPs, respectively. Furthermore, the catalyst also displayed a great stability in methanol oxidation after 200 scanning cycles, implying the excellent tolerance toward the CO poisoning effect.