Effects of membrane content, feed phase, and stripping phase for palladium solution extraction by using a polymer inclusion membrane.

Palladium is now frequently utilized in fuel cells, electroplating, electronics, and catalysis. Due to their rarity and high cost, precious metal recovery has taken on a significant role. The extraction method frequently utilized in polymer inclusion membranes (PIMs) is both efficient and simple since it has been demonstrated that precious metal adsorption on the membrane significantly controls the mechanism of chemical adsorption. In this study, polyvinyl chloride (PVC) as a polymer, A336 as a plasticizer, and trioctylamine (TOA) as a carrier were used to produce a PIM by evaporation. After the production of PIMs, palladium extract was studied. The stripping phase, palladium concentration in the feed phase, and components of the membrane were changed to determine the optimum condition with better extraction ability. When 0.5 M of HCl was used, higher kinetic parameter results and higher than 85% extraction efficiency were achieved compared to other concen- trations. When the EDX results were examined, 3.3% palladium was retained on the membrane surface. When the palladium concentration was selected at 2.5 ppm, higher kinetic parameters were observed, and the extraction efficiency was over 90%. The best membrane was the PIM containing 40% PVC-40% A336-20% TOA.

Determination of Cadmium (II) in Aqueous Solutions by In Situ MID-FTIR-PLS Analysis Using a Polymer Inclusion Membrane-Based Sensor: First Considerations.

Environmental monitoring is one of the most dynamically developing branches of chemical analysis. In this area, the use of multidimensional techniques and methods is encouraged to allow reliable determinations of metal ions with portable equipment for in-field applications. In this regard, this study presents, for the first time, the capabilities of a polymer inclusion membrane (PIM) sensor to perform cadmium (II) determination in aqueous solutions by in situ visible (VIS) and Mid- Fourier transform infrared spectroscopy (MID-FTIR) analyses of the polymeric films, using a partial least squares (PLS) chemometric approach. The influence of pH and metal content on cadmium (II) extraction, the characterization of its extraction in terms of the adsorption isotherm, enrichment factor and extraction equilibrium were studied. The PLS chemometric algorithm was applied to the spectral data to establish the relationship between cadmium (II) content in the membrane and the absorption spectra. Furthermore, the developed MID-FTIR method was validated through the determination of the figures of merit (accuracy, linearity, sensitivity, analytical sensitivity, minimum discernible concentration difference, mean selectivity, and limits of detection and quantitation). Results showed reliable calibration curves denoting systems' potentiality. Comparable results were obtained in the analysis of real samples (tap, bottle, and pier water) between the new MID-FTIR-PLS PIM based-sensor and F-AAS.

Use of a Polymer Inclusion Membrane and a Chelating Resin for the Flow-Based Sequential Determination of Copper(II) and Zinc(II) in Natural Waters and Soil Leachates.

A bi-parametric sequential injection method for the determination of copper(II) and zinc(II) when present together in aqueous samples was developed. This was achieved by using a non-specific colorimetric reagent (4-(2-pyridylazo)resorcinol, PAR) together with two ion-exchange polymeric materials to discriminate between the two metal ions. A polymer inclusion membrane (PIM) and a chelating resin (Chelex 100) were the chosen materials to retain zinc(II) and copper(II), respectively. The influence of the flow system parameters, such as composition of the reagent solutions, flow rates and standard/sample volume, on the method sensitivity were studied. The interference of several common metal ions was assessed, and no significant interferences were observed (<10% signal deviation). The limits of detection were 3.1 and 5.6 µg L-1 for copper(II) and zinc(II), respectively; the dynamic working range was from 10 to 40 µg L-1 for both analytes. The newly developed sequential injection analysis (SIA) system was applied to natural waters and soil leachates, and the results were in agreement with those obtained with the reference procedure.

Selective Separation of Acetic and Hexanoic Acids across Polymer Inclusion Membrane with Ionic Liquids as Carrier.

This paper first reports on the selective separation of volatile fatty acids (VFAs) (acetic and hexanoic acids) using polymer inclusion membranes (PIMs) containing quaternary ammonium and phosphonium ionic liquids (ILs) as the carrier. The affecting parameters such as IL content, VFA concentration, and the initial pH of the feed solution as well as the type and concentration of the stripping solution were investigated. PIMs performed a much higher selective separation performance toward hexanoic acid. The optimal PIM composed of 60 wt% quaternary ammonium IL with the permeability coefficients for acetic and hexanoic acid of 0.72 and 4.38 µm s-1, respectively, was determined. The purity of hexanoic acid obtained in the stripping solution increased with an increase in the VFA concentration of the feed solution and decreasing HCl concentration of the stripping solution. The use of Na2CO3 as the stripping solution and the involvement of the electrodialysis process could dramatically enhance the transport efficiency of both VFAs, but the separation efficiency decreased sharply. Furthermore, a coordinating mechanism containing hydrogen bonding and ion exchange for VFA transport was demonstrated. The highest purity of hexanoic acid (89.3%) in the stripping solution demonstrated that this PIM technology has good prospects for the separation and recovery of VFAs from aqueous solutions.

First Report on a Solvent-Free Preparation of Polymer Inclusion Membranes with an Ionic Liquid.

A novel and environmentally-friendly procedure for the preparation of polymer inclusion membranes (PIMs) containing an ionic liquid is presented for the first time. Traditionally, PIMs are prepared by a solvent casting method with the use of harmful organic solvents. Here we report a new solvent-free procedure based on a thermal-compression technique which involve the melting of the components of the PIM and the application of a high pressure to the melted specimen to form a flat-sheet film. In our study, we have tested different polymers, such as two cellulose derivatives as well as two thermoplastic polymers, polyurethane (TPU) and poli ε-caprolactone (PCL). The ionic liquid (IL) trioctylmethylammonium chloride (Aliquat 336) has been used to produce PIMs with a fixed composition of 70% polymer-30% IL (w/w). Both TPU and PCL polymers provide successful membranes, which have been thoroughly characterized. PIMs based on the polymer PCL showed a high stability. To test whether the properties of the IL were affected by the preparation conditions, the extraction ability of Aliquat 336 was investigated for both PCL and TPU membranes in terms of Cr(VI) extraction. Satisfactory values (90% extraction) were obtained for both membranes tested, showing this novel procedure as a green alternative for the preparation of PIMs with ILs.

In-Transit Electroextraction of Small-Molecule Pharmaceuticals from Blood.

An electrokinetic platform was developed for extracting small-molecule pharmaceuticals from a dried blood spot. Through the exclusion of liquid reagents and use of low field strength (6 V cm-1 ), the electroextraction of a drug from a dried blood spot, deposited on a polymer inclusion membrane (PIM), could be realised while in transit in the mail. In transit sample preparation provides a potential solution to in situ sample degradation and may accelerate the workflow upon arrival of a patient sample at the analytical facility. The electroextraction method was enabled through our discovery of the use of 15-20 µm thin PIMs as electrophoretic separation medium in absence of liquid reagents. Here, a PIM consisting of cellulose triacetate as polymer base, 2-nitrophenyl octyl ether as plasticizer and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide as carrier was used. The PIM, was packaged with two 12 V batteries to supply the separation voltage. A blood spot containing berberine chloride was deposited and dried before the applying the separation potential, allowing for the electroextraction while the packaged device was shipped in internal mail. Upon arrival in the analytical laboratory, the PIM was analysed using a fluorescence microscope with photon multiplier tube, quantifying the berberine extracted away from the sample matrix. This platform represents a new opportunity for processing clinical samples during transport to the laboratory, saving time and manual handling to accelerate the time to result.

Removal of Methylene Blue Dye from Aqueous Solutions Using Polymer Inclusion Membrane Containing Calix[4]pyrrole.

The effective purification of aqueous solutions of methylene blue dye was tested using polymer inclusion membranes (PIMs) that contained cellulose triacetate (CTA) as a polymer base, o-nitrophenyl octyl ether (o-NPOE) as a plasticizer, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) as a carrier. Scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy were used to define the microstructure and surface of PIMs. Experimental results showed that, with an increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation showed that the flux increased with the rise in the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane's transport properties. The optimal composition of the membrane in percent by weight for KP was 74% plasticizer; 18% support, and 8% carrier. The maximum MB removal (93.10%) was achieved at 0.10 M HCl solution as the receiving phase. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

A Comprehensive Study on the Effect of Plasticizers on the Characteristics of Polymer Inclusion Membranes (PIMs): Exploring Butyl Stearate as a Promising Alternative.

This study investigated the influence of various plasticizers commonly used in the manufacture of polymer inclusion membranes (PIMs), such as 2-nitrophenyl octyl ether (NPOE), phthalates, adipates, and sebacates on the mechanical, thermal, and transport properties of membranes. Additionally, butyl stearate (BTS), chosen for its non-toxic nature compared to phthalates and its cost-effectiveness relative to adipates and sebacates, was evaluated as a plasticizer in PIMs for the first time. All plasticizers were incorporated in PIMs made of either cellulose triacetate (CTA) or poly(vinyl chloride) (PVC) as the base polymers and the task-specific ionic liquid trioctylmethylammonium thiosalicylate (TOMATS) as the carrier. The plasticizers were found to significantly affect the characteristics of membrane hydrophilicity, mechanical flexibility, and thermal stability. Transport experiments using Hg(II) as a model target ion revealed that, for CTA-based PIMs, the plasticizer did not significantly affect transport efficiency. However, for PVC-based PIMs, BTS exhibited better efficiency when compared to NPOE. These findings highlight the potential of BTS as an attractive alternative to currently used plasticizers in PVC-based PIM formulations.

PVDF-HFP-based polymer inclusion membrane functionalized with D2EHPA for the selective extraction of bismuth(III) from sulfate media.

This study is the first application of a PVDF-HFP-based polymer inclusion membrane incorporating the poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and di(2-ethylhexyl)phosphoric acid (D2EHPA) as the base polymer and extractant for the extraction of bismuth(III), respectively. It is demonstrated that the PIM comprised of 60 wt% PVDF-HFP and 40 wt% D2EHPA is the most effective in the extraction of bismuth(III) from feed solution containing 20 mg L-1 bismuth(III) and 0.2 mol L-1 sulfate adjusted to pH 1.4. The extracted bismuth(III) ions are back-extracted quantitatively to the receiving solution containing 1 mol L-1 sulfuric acid. The stoichiometry experiments reveal that the Bi: D2EHPA ratio in the bismuth(III) extracted complex is 1:6, and D2EHPA is dimer. Moreover, it is shown that the studied PIM has high selectivity in the extraction of bismuth(III) over other interfering ions such as Mo(VI), Cr(III), Al(III), Fe(III), Ni(II), Zn(II), Cd(II), Co(II), Cu(II), and Mn(II). The interference of Fe(III) is also eliminated by masking with fluoride, leading finally to a nearly pure extraction of bismuth(III).

Characterization of Quaternary-Ammonium-Based Ionogel Membranes for Application in Proton Exchange Membrane Fuel Cells.

In recent years, the quest to advance fuel cell technologies has intensified, driven by the imperative to reduce reliance on hydrocarbon-derived fuels and mitigate pollutant emissions. Proton exchange membranes are a critical material of fuel cell technologies. The potential of ionic liquid-based polymer inclusion membranes or ionogels for proton exchange membrane fuel cells (PEMFCs) has recently appeared. Thermal stability, SEM-EDX characterization, NMR and IR characterization, thermogravimetric analysis, ion exchange capacity, and water uptake are key properties of these membranes which need to be investigated. In this work, ionogel based on quaternary ammonium salts, such as [N8,8,8,1+][Cl-], [N8,8,8,1+][Br-], and [N8-10,8-10,8-10,1+][Cl-] in various compositions with poly(vinyl chloride) are extensively studied and characterized based on those key properties. The best properties were obtained when a quaternary ammonium cation was combined with a bromide anion. Finally, ionogels are tested in microbial fuel cells. Microbial fuel cells based on the ionogel reach a maximum of 147 mW/m2, which represents 55% of the reference membrane (Nafion 212). These results indicate that we still have the possibility of improvement through the appropriate selection of the cation and anion of the ionic liquid. Overall, the promise of ionogel membranes as a viable alternative in fuel cell applications has been demonstrated.

MID-FTIR-PLS Chemometric Analysis of Cr(VI) from Aqueous Solutions Using a Polymer Inclusion Membrane-Based Sensor.

A partial least squares (PLS) quantitative chemometric method based on the analysis of the mid-Fourier transform infrared spectroscopy (MID-FTIR) spectrum of polymer inclusion membranes (PIMs) used for the extraction of Cr(VI) from aqueous media is developed. The system previously optimized considering the variables membrane composition, extraction time, and pH, is characterized in terms of its adsorption isotherm, distribution coefficient, extraction percent, and enrichment factor. A Langmuir-type adsorption behavior with KL = 2199 cm3/mmol, qmax = 0.188 mmol/g, and 0 < RL < 1 indicates that metal adsorption is favorable. The characterization of the extraction reaction is performed as well, showing a 1:1 Cr(VI):Aliquat 336 ratio, in agreement with solvent extraction data. The principal component analysis (PCA) of the PIMs reveals a complex pattern, which is satisfactorily simplified and related to Cr(VI) concentrations through the use of a variable selection method (iPLS) in which the bands in the ranges 3451-3500 cm-1 and 3751-3800 cm-1 are chosen. The final PLS model, including the 100 wavelengths selected by iPLS and 10 latent variables, shows excellent parameter values with root mean square error of calibration (RMSEC) of 3.73115, root mean square error of cross-validation (RMSECV) of 6.82685, bias of -1.91847 × 10-13, cross-validation (CV) bias of 0.185947, R2 Cal of 0.98145, R2 CV of 0.940902, recovery% of 104.02 ± 4.12 (α = 0.05), sensitivity% of 0.001547 ppb, analytical sensitivity (γ) of 3.8 ppb, γ-1: 0.6 ppb-1, selectivity of 0.0155, linear range of 5.8-100 ppb, limit of detection (LD) of 1.9 ppb, and limit of quantitation (LQ) of 5.8 ppb. The developed PIM sensor is easy to implement as it requires few manipulations and a reduced number of chemical compounds in comparison to other similar reported systems.

Mechanistic investigation of intensified separation of molybdenum(VI) and vanadium(V) using polymer inclusion membrane electrodialysis.

The main challenge in separating molybdenum(VI) and vanadium(V) which have similar properties results in great difficulties in the green recycling of hazardous spent catalysts. Here, selective facilitating transport and stripping are integrated into the polymer inclusion membrane electrodialysis process (PIMED) to separate Mo(VI) and V(V) to overcome the complicated co-extraction and stepwise-stripping in conventional solvent extraction. The influences of various parameters, the selective transport mechanism, and respective activation parameters were systematically investigated. Results revealed that the affinity of the Aliquat 36 as the carrier and PVDF-HFP as the base polymer of PIM towards Mo(VI) is stronger than that of V(V), while the strong interaction between Mo(VI) and carrier caused low migration through the membrane. By the combination of adjusting and controlling the electric density and strip acidity, the interaction was destroyed and the transport was facilitated. After optimization, stripping efficiencies of Mo(VI) and V (V) increased from 44.4% to 93.1% and reduced from 31.9% to 1.8%, respectively, while their separation coefficient increased 16.3 times to 333.4. The activation energy, enthalpy and entropy for the transport of Mo(VI) were determined to be 4.846 kJ mol-1, 6.745 kJ mol-1 and - 310.838 J mol-1 K-1, respectively. The present work demonstrates that the separation of similar metal ions could be improved by fine tuning the affinity and interaction between metal ions and the PIM, thus providing new insights into the recycling of similar metal ions from secondary resources.

Fabrication and characterisation of novel chitosan-based polymer inclusion membranes and their application in environmental remediation.

Several water and wastewater technologies have been implored for the removal of dyes during wastewater treatments; however; different types have been reportedly found in surface and groundwater systems. Hence, there is a need to investigate other water treatment technologies for the complete remediation of dyes in aquatic environments. In this study, novel chitosan-based polymer inclusion membranes (PIMs) were synthesized for the removal of malachite green dye (MG) which is a recalcitrant of great concern in water. Two types of PIMs were synthesized in this study, the first PIM (PIMs-A) was composed of chitosan, bis-(2-ethylhexyl) phosphate (B2EHP), and dioctyl phthalate (DOP). While, the second PIMs (PIMs-B) were composed of chitosan, Aliquat 336, and DOP. The physico-thermal stability of the PIMs was investigated using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA), both PIMs demonstrated good stability with a weak intermolecular force of attraction amongst the various components of the membranes. The effects of the initial concentration of MG, pH of the MG solution, stripping solution, and time were investigated. At optimum conditions, both membranes (PIM-A and B) recorded the highest efficiencies of 96 % and 98 % at pH 4 and initial contaminants concentration of 50 mg/L, respectively. Finally, both PIMs were used for the removal of MG in different environmental samples (river water, seawater, and tap water) with an average removal efficiency of 90 %. Thus, the investigated PIMs can be considered a potential suitable technique for the removal of dyes and other contaminants from aquatic matrices.

The Application of Polymer Inclusion Membranes for the Removal of Emerging Contaminants and Synthetic Dyes from Aqueous Solutions-A Mini Review.

Pollution of the environment, including water resources, is currently one of the greatest challenges due to emerging new contaminants of anthropogenic origin. Of particular concern are emerging organic pollutants such as pharmaceuticals, endocrine disruptors, and pesticides, but also other industrial pollutants, for example, synthetic dyes. The growing demand for environmentally friendly and economical methods of removing emerging contaminants and synthetic dyes from wastewater resulted in increased interest in the possibility of using techniques based on the application of polymer inclusion membranes (PIMs) for this purpose. PIM-based techniques are promising methods for eliminating emerging contaminants and synthetic dyes from aqueous solutions, including wastewater, due to high efficiency, membranes versatility, ease/low cost of preparation, and high selectivity. This review describes the latest developments related to the removal of various emerging contaminants and synthetic dyes from aqueous solutions using PIMs over the past few years, with particular emphasis on research aimed at increasing the effectiveness and selectivity of PIMs, which may contribute to wider use of these methods in the future.

Modified LIX®84I-Based Polymer Inclusion Membranes for Facilitating the Transport Flux of Cu(II) and Variations of Their Physical-Chemical Characteristics.

A unique facilitation on the transport flux of Cu(II) was investigated by using modified polymer inclusion membranes (PIMs). LIX®84I-based polymer inclusion membranes (LIX®-based PIMs) using poly(vinyl chloride) (PVC) as support, 2-nitrophenyl octyl ether (NPOE) as plasticizer and Lix84I as carrier were modified by reagents with different polar groups. The modified LIX®-based PIMs showed an increasing transport flux of Cu(II) with the help of ethanol or Versatic acid 10 modifiers. The metal fluxes with the modified LIX®-based PIMs were observed varying with the amount of modifiers, and the transmission time was cut by half for the modified LIX®-based PIM cast with Versatic acid 10. The physical-chemical characteristics of the prepared blank PIMs with different Versatic acid 10 were further characterized by using attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), contract angle measurements and electro-chemical impedance spectroscopy (EIS). The characterization results indicated that the modified LIX®-based PIMs cast with Versatic acid 10 appeared to be more hydrophilic with increasing membrane dielectric constant and electrical conductivity that allowed better accessibility of Cu(II) across PIMs. Hence, it was deduced that hydrophilic modification might be a potential method to improve the transport flux of the PIM system.

A Novel Polymer Inclusion Membrane-Based Green Optical Sensor for Selective Determination of Iron: Design, Characterization, and Analytical Applications.

The design, characterization, and analytical application of a green optical sensor for the selective determination of Fe(II) ions is proposed. The sensor is based on the immobilization of the chromogenic reagent picolinaldehyde salicyloylhydrazone (SHPA) within a polymer inclusion membrane. To reduce solvent usage, the reagent was synthesized using a green mechanochemical procedure. The components for sensor preparation were optimized with a sequential simplex method and the optimal composition was found to be 0.59 g cellulose triacetate (base polymer), 0.04 g SHPA (chemosensor reagent), 4.9 mL dibutyl phthalate (plasticizer), and 38 mL dichloromethane (solvent). The conditions of iron analysis were also optimized resulting in pH 6 for aqueous solution, 90 min exposure time and 10 min short-term stability. The optical sensor showed a linear range from the limit of detection (0.48 µmol L-1) to 54 µmol L-1 Fe(II). The precision of the method was found to be 1.44% and 1.19% for 17.9 and 45 µmol L-1 Fe(II), respectively. The characteristics of the sensor allowed the design of a Fe(II)/Fe(III) speciation scheme. The methodology was successfully applied to the determination of iron in food preservatives, food additives, and dietary supplement. Additionally, the Fe speciation scheme was successfully applied to an agricultural fertilizer.

Efficient separation of arsenic species of oxyanion As (III) and As (V) by using effective polymer inclusion membranes (PIM).

The heavy metal contaminant arsenic exist in the form of arsenite (As(III)) and arsenate (As(V)) ions. These ions are highly carcinogenic that are usually present in the ground water. To date, most of the designed polymer inclusion membrane (PIM) involved only about separation without differentiating the oxidation states. Thus, there is a research gap on separation of element with different oxidation states. Thus, this study addresses such research gap which have been not explored previously. To extract such ions from water, the present study involves fabrication of PIM by varying the compositions of the base polymer, carrier and plasticizer. Also effect of the strip solution, and transport properties were studied. High performance membrane was obtained with 50% (w/w) Aliquat 336 and 50% (w/w) Cellulose triacetate (CTA). The production of 1 m2 of PIM may cost approximately 0.08-0.16$. Also, we have combined the separation capacity of polymer inclusion membrane (PIM) with the sensitivity and elemental detection using atomic absorption spectrometry (AAS) to detect and separate As(III) and As(V). AAS is limited to detecting only elemental arsenic (As) and does not distinguish between As(III) and As(V). Further, to address such limitations in this current study we were able to separate As(V) from As(III) within 5 h. In addition, to provide sole solution a device was fabricated to extract As(V) in the field studies which displayed outstanding efficiency of 99.7 ± 0.2%. The extracted samples was tested in AAS to differentiate between oxidation states of the arsenic species and these important results are supportive in finding out the redox potential of water and for other geochemical explorations.

The Use of Polymer Membranes for the Recovery of Copper, Zinc and Nickel from Model Solutions and Jewellery Waste.

A polymeric inclusion membrane (PIM) consisting of matrix CTA (cellulose triacetate), ONPPE (o-nitrophenyl pentyl ether) and phosphonium salts (Cyphos 101, Cyphos 104) was used for separation of Cu(II), Zn(II) and Ni(II) ions. Optimum conditions for metal separation were determined, i.e., the optimal concentration of phosphonium salts in the membrane, as well as the optimal concentration of chloride ions in the feeding phase. On the basis of analytical determinations, the values of parameters characterizing transport were calculated. The tested membranes most effectively transported Cu(II) and Zn(II) ions. The highest recovery coefficients (RF) were found for PIMs with Cyphos IL 101. For Cu(II) and Zn(II), they are 92% and 51%, respectively. Ni(II) ions practically remain in the feed phase because they do not form anionic complexes with chloride ions. The obtained results suggest that there is a possibility of using these membranes for separation of Cu(II) over Zn(II) and Ni(II) from acidic chloride solutions. The PIM with Cyphos IL 101 can be used to recover copper and zinc from jewellery waste. The PIMs were characterized by AFM and SEM microscopy. The calculated values of the diffusion coefficient indicate that the boundary stage of the process is the diffusion of the complex salt of the metal ion with the carrier through the membrane.

The Latest Achievements of Liquid Membranes for Rare Earth Elements Recovery from Aqueous Solutions-A Mini Review.

The systematic increase in the use of rare earth elements (REEs) in various technologically advanced products around the world (e.g., in electronic devices), the growing amount of waste generated by the use of high-tech materials, and the limited resources of naturally occurring REE ores resulted in an intensive search for effective and environmentally safe methods for recovering these elements. Among these methods, techniques based on the application of various types of liquid membranes (LMs) play an important role, primarily due to their high efficiency, the simplicity of membrane formation and use, the utilization of only small amounts of environmentally hazardous reagents, and the possibility of simultaneous extraction and back-extraction and reusing the membranes after regeneration. However, because both primary and secondary sources (e.g., waste) of REEs are usually complex and contain a wide variety of components, and the selectivity and efficiency of LMs depend on many factors (e.g., the composition and form of the membrane, nature of the recovered ions, composition of the feed and stripping phases, etc.), new membranes are being developed that are "tailored" to the properties of the recovered rare earth elements and to the character of the solution in which they occur. This review describes the latest achievements (since 2019) related to the recovery of a range of REEs with the use of various liquid membranes (supported liquid membranes (SLMs), emulsion liquid membranes (ELMs), and polymer inclusion membranes (PIMs)), with particular emphasis on methods that fall within the trend of eco-friendly solutions.

The Use of Polymer Inclusion Membranes for the Removal of Metal Ions from Aqueous Solutions-The Latest Achievements and Potential Industrial Applications: A Review.

The growing demand for environmentally friendly and economical methods of removing toxic metal ions from polluted waters and for the recovery of valuable noble metal ions from various types of waste, which are often treated as their secondary source, has resulted in increased interest in techniques based on the utilization of polymer inclusion membranes (PIMs). PIMs are characterized by many advantages (e.g., the possibility of simultaneous extraction and back extraction, excellent stability and high reusability), and can be adapted to the properties of the removed target analyte by appropriate selection of carriers, polymers and plasticizers used for their formulation. However, the selectivity and efficiency of the membrane process depends on many factors (e.g., membrane composition, nature of removed metal ions, composition of aqueous feed solution, etc.), and new membranes are systematically designed to improve these parameters. Numerous studies aimed at improving PIM technology may contribute to the wider use of these methods in the future on an industrial scale, e.g., in wastewater treatment. This review describes the latest achievements related to the removal of various metal ions by PIMs over the past 3 years, with particular emphasis on solutions with potential industrial application.