Unlocking Auxetic Behavior in Recyclable Thermosetting Foams Enabled by Dynamic Disulfide Cross-linking Strategy.

Auxetic foams with a negative Poisson's ratio (NPR) have attracted considerable attention in material engineering due to their outstanding performance in seismic and energy absorption. Nevertheless, thermoplastic auxetic foams are compromised by weak non-covalent crosslinking that diminishes the mechanical strength and durability of foams. Conversely, thermosetting foams with chemical crosslinking, although mechanically robust, face challenges in elaborating auxetic structure and in achieving recyclability. Herein, an alternative approach is proposed to tackle this dilemma by incorporating dynamic disulfide bonds into the polymer network for preparing a thermosetting polyurethane foam with covalent adaptable network. By leveraging the unidirectional multi-effect compression technique, the topological network reorganization of foam is induced, transforming the initial circular open-cell structure into a re-entrant cell structure. This structural transformation endows the foam with stable NPR capability, achieving a minimum Poisson's ratio value of -0.4 within 30% compressive strain. Benefiting from its reinforced network structure, the foam also demonstrates high compressive strength (6.47 MPa) and tensile strength (1.67 MPa). Furthermore, it is recyclable and can be recompressed into thermosetting films. This work offers a straightforward approach to making auxetic thermosetting foams with good mechanical and recyclable properties, which is interesting for the development of high-performance auxetic materials.

Deamination of Polyols from the Glycolysis of Polyurethane.

Methylenedianiline (MDA) is a secondary, undesired, product of the glycolysis process of polyurethane (PU) scraps due to hydrolysis and pyrolysis side reactions. As an aromatic and carcinogen amine, MDA poses different problems in handling, transporting, and labelling recycled polyols derived from glycolysis, hindering the closure of PU recycling loop. Aiming to provide a solution to this issue, in this work different deaminating agents (DAs) were investigated with the purpose of analyzing their reactivity with MDA. A first part of the study was devoted to the analysis of MDA formation as a function of reaction time and catalyst concentration (potassium acetate) during glycolysis. It was observed that the amount of MDA increases almost linearly with the extent of PU depolymerization and catalyst content. Among the DAs analyzed 2-ethylhexyl glycidyl ether (2-EHGE), and acetic anhydride (Ac2 O) showed interesting performance, which allowed MDA content to be diminished below the limit for labelling prescription in 30 minutes. PU rigid foams were, therefore, synthesized from the corresponding recycled products and characterized in terms of thermal and mechanical performance. Ac2 O-deaminated polyols led to structurally unstable foams with poor compressive strength, while 2-EHGE-deaminated products allowed the production of foams with improved mechanical performance and unaltered thermal conductivity.

Engineering Sulfur-Containing Polymeric Fire-Retardant Coatings for Fire-Safe Rigid Polyurethane Foam.

With the advantages of lightweight and low thermal conductivity properties, polymeric foams are widely employed as thermal insulation materials for energy-saving buildings but suffer from inherent flammability. Flame-retardant coatings hold great promise for improving the fire safety of these foams without deteriorating the mechanical-physical properties of the foam. In this work, four kinds of sulfur-based flame-retardant copolymers are synthesized via a facile radical copolymerization. The sulfur-containing monomers serve as flame-retardant agents including vinyl sulfonic acid sodium (SPS), ethylene sulfonic acid sodium (VS), and sodium p-styrene sulfonate (VSS). Additionally, 2-hydroxyethyl acrylate (HEA) and 4-hydroxybutyl acrylate are employed to enable a strong interface adhesion with polymeric foams through interfacial H-bonding. By using as-synthesized waterborne flame-retardant polymeric coating with a thickness of 600 µm, the coated polyurethane foam (PUF) can achieve a desired V-0 rating during the vertical burning test with a high limiting oxygen index (LOI) of >31.5 vol%. By comparing these sulfur-containing polymeric fire-retardant coatings, poly(VS-co-HEA) coated PUF demonstrates the best interface adhesion capability and flame-retardant performance, with the lowest peak heat release rate of 166 kW m-2 and the highest LOI of 36.4 vol%. This work provides new avenues for the design and performance optimization of advanced fire-retardant polymeric coatings.

Wearable EMG Measurement Device Using Polyurethane Foam for Motion Artifact Suppression.

We propose the use of a specially designed polyurethane foam with a plateau region in its mechanical characteristics-where stress remains nearly constant during deformation-between the electromyography (EMG) electrode and clothing to suppress motion artifacts in EMG measurement. Wearable EMG devices are receiving attention for monitoring muscle weakening due to aging. However, daily EMG measurement has been challenging due to motion artifacts caused by changes in the contact pressure between the bioelectrode and the skin. Therefore, this study aims to measure EMG signals in daily movement environments by controlling the contact pressure using polyurethane foam between the bioelectrode on the clothing and the skin. Through mechanical calculations and finite element method simulations of the polyurethane foam's effect, we clarified that the characteristics of the polyurethane foam significantly influence contact pressure control and that the contact pressure is adjustable through the polyurethane foam thickness. The optimization of the design successfully controlled the contact pressure between the bioelectrode and skin from 1.0 kPa to 2.0 kPa, effectively suppressing the motion artifact in EMG measurement.

Enhanced Fire Safety of Energy-Saving Foam by Self-Cleavage CO2 Pre-Combustion and Phosphorus Release Post-Combustion.

Rigid polyurethane foam (RPUF) is widely utilized in construction and rail transportation due to its lightweight properties and low thermal conductivity, contributing to energy conservation and emission reduction. However, the inherent flammability of RPUF presents significant challenges. Delaying the time to ignition and preventing flame spread post-combustion is crucial for ensuring sufficient evacuation time in the event of a fire. Based on this principle, this study explores the efficacy of using potassium salts as a catalyst to promote the self-cleavage of RPUF, generating substantial amounts of CO2, thereby reducing the local oxygen concentration and delaying ignition. Additionally, the inclusion of a reactive flame retardant (DFD) facilitates the release of phosphorus-oxygen free radicals during combustion, disrupting the combustion chain reaction and thus mitigating flame propagation. Moreover, potassium salt-induced catalytic carbonization and phosphorus derivative cross-linking enhance the condensed phase flame retardancy. Consequently, the combined application of potassium salts and DFD increases the limiting oxygen index (LOI) and reduces both peak heat release rate (PHRR) and total heat release (THR). Importantly, the incorporation of these additives does not compromise the compressive strength or thermal insulation performance of RPUF. This integrated approach offers a new and effective strategy for the development of flame retardant RPUF.

Low-cost, reliable, and highly efficient removal of COD and total nitrogen from sewage using a sponge-filled trickling filter.

Development of low-cost and reliable reactors demanding minimal supervision is a need-of-the-hour for sewage treatment in rural areas. This study explores the performance of a multi-stage sponge-filled trickling filter (SPTF) for sewage treatment, employing polyethylene (PE) and polyurethane (PU) media. Chemical oxygen demand (COD) and nitrogen transformation were evaluated at hydraulic loading rates (HLRs) ranging from 2 to 6 m/d using synthetic sewage as influent. At influent COD of ∼350 mg/L, PU-SPTF and PE-SPTF achieved a COD removal of 97% across all HLRs with most of the removal occurring in the first segments. Operation of PE-SPTF at an HLR of 6 m/d caused substantial wash-out of biomass, while PU-SPTF retained biomass and achieved effluent COD < 10 mg/L even at HLR of 8-10 m/d. The maximum Total Nitrogen removal by PE-SPTF and PU-SPTF reactors was 93.56 ± 1.36 and 92.24 ± 0.66%, respectively, at an HLR of 6 m/d. Simultaneous removal of ammonia and nitrate was observed at all the HLRs in the first segment of both SPTFs indicating ANAMMOX activity. COD removal data, media depth, and HLRs were fitted (R2 > 0.99) to a first-order kinetic relationship. For a comparable COD removal, CO2 emission by PU-SPTF was 3.5% of that of an activated sludge system.

Valorization of polyurethane foam waste through the decoration with nano-polyaniline for dye decontamination from polluted water.

Two polyurethane polyaniline nanocomposites have been synthesized using two in situ polymerization routes of dried and wet bases to valorize the polyurethane waste. The physical and chemical properties of polyurethane-based nanocomposites were compared using SEM, XRD, FTIR, and Zeta potential. SEM images showed that the average particle size of the dried-based composite was 56 nm, while the wet-based composite had an average size of 75 nm. The separation efficiency for methylene blue (MB) and Congo red (CR) dyes was evaluated against free polyurethane foam waste. It was evident that pure polyurethane (PPU) achieved only 4.79% and 16.71% removal for MB and CR, respectively. These dye decontamination efficiencies were enhanced after nano polyaniline decoration of polyurethane foam either through dried base polymerization (DPUP) or wet base polymerization (WPUP). WPUP composite records 11.23% and 85.99% for MB and CR removal, respectively, improved to 26.69% and 90.07% removal using DPUP composite for the respective dyes. The adsorption kinetics, isotherms, and thermodynamics were investigated. The experimental results revealed the pseudo-second-order kinetic model as the most accurately described kinetics model for both CR and MB adsorption. The Langmuir model provided the best fit for the data, with maximum adsorption capacities of 110.98 mg/g for CR and 26.86 mg/g for MB, with corresponding R-squared values of 0.9974 and 0.9608, respectively. Regeneration and reusability studies of PPU, WPUP, and DPUP showed effective reusability, with DPUP displaying the highest adsorption capacity. These results aid in creating eco-friendly and cost-efficient adsorbents for dye removal in environmental sanitation.

Calibration and Application of PUF Disk Passive Air Samplers To Assess Chlorinated Paraffins in Ambient Air in Australia, China, and Vietnam.

Ambient air samples were collected in Brisbane (Australia), Dalian (China), and Hanoi (Vietnam) during Mar 2013-Feb 2018 using polyurethane foam based passive air samplers. A sampling rate calibration experiment was conducted for chlorinated paraffins (CPs, i.e., short-chain, medium-chain, and long-chain CPs), where the sampling rates were 4.5 ± 0.7, 4.8 ± 0.3, and 4.8 ± 2.1 m3 day-1 for SCCPs, MCCPs, and LCCPs, respectively. The atmospheric concentration of CPs was then calculated and the medians of ∑CPs were 0.079, 1.0, and 0.89 ng m-3 in Brisbane, Dalian, and Hanoi, respectively. The concentration of CPs in Brisbane's air remained at low levels, with no significant differences observed between the city background site and the city center site, indicating limited usage and production of CPs in this city. The highest concentration of MCCPs was detected in Dalian, while the highest concentration of SCCPs was detected in Hanoi. A decrease of SCCP concentration and an increase of MCCPs' were found in Brisbane's air from 2016 to 2018, while increasing trends for both SCCPs and MCCPs were observed in Dalian. These results indicated impacts from different sources of CPs in the investigated cities.

Fabrication of a novel polyurethane foam-alginate-zeolite hydrogel and subsequent KSND bacteria encapsulation: evidence of accelerated biofilm colonization and enhanced nitrogen removal efficiency.

Biofilms are used widely to remove nitrogen from wastewater; however, most biofilm carriers (i.e. polyurethane foam, PUF) are hydrophobic organic materials with millimetre-scale apertures, ineffective attachment, and unstable colonization of microorganisms. To address these limitations, hydrophilic sodium alginate (SA) mixed with zeolite powder (Zeo) was cross-linked in PUF to form a micro-scale hydrogel (PAS) with a well-organized and reticular cellular structure. Scanning electron microscopy revealed that immobilized cells were entrapped in the interior of hydrogel filaments and rapidly formed a stable biofilm on the surface. The biofilm generated was 10.3-fold greater than the film developed on PUF. Kinetics and isotherm studies revealed that the as-developed carrier, because of the presence of Zeo, effectively improved the adsorption of NH4+-N by 53%. The PAS carrier achieved total nitrogen removal in excess of 86% for low carbon-to-nitrogen ratio wastewater treated for 30 d, indicating that this novel modification-encapsulation technology has potential for wastewater treatment.

A radiologic determination of the different screw cutting patterns in cut and uncut orthopedic cortical screws using a novel imaging technique.

OBJECTIVE: We hypothesize that cut screws will deform in a manner that increases the core and outer diameters of the screw hole compared to uncut controls, and effects will be more pronounced in titanium screws. MATERIALS AND METHODS: We used biomechanical polyurethane foam blocks to simulate cortical bone. We organized four groups of stainless steel and titanium cut and uncut screws. Blocks were fitted with a jig to ensure perpendicular screw insertion. We imaged the blocks using digital mammography and measured them using PACS software. Power analysis determined a power of 0.95 and an alpha error of 0.05. RESULTS: Highly statistically significant differences in core diameter were found after cutting stainless steel and titanium screws. Cutting stainless steel screws increased core diameter by 0.30 mm (95% CI, 0.16 to 0.45; p < .001). Titanium screws' core diameter increased by 0.45 mm (95% CI, 0.30 to 0.61; p < .001). No significant differences were found in the outer diameters of stainless steel and titanium screws after cutting. CONCLUSION: Titanium and stainless steel screw tracts demonstrated screw core diameter and screw thread pattern deformation after cutting. Titanium screws demonstrated more significant effects.

Emission and time-resolved migration rates of aromatic diamines from two flexible polyurethane foams.

Performing risk assessments (RA) on household use of flexible polyurethane (PU) foams requires access to reliable data about emission and migration of potential diamine impurities. A toluene diisocyanate (TDI) and a methylene diphenyl diisocyanate (MDI) based foam were thermally treated to enable measurements on samples with defined concentrations of the corresponding diamines, toluene diamine (TDA), and methylene dianiline (MDA). The thermally treated foams used for emission testing contained up to 15 mg.kg-1 of TDA and 27 mg.kg-1 of MDA. Those used for migration testing contained 5.1 mg.kg-1 of TDA and 14.1 mg.kg-1 of MDA. Stability of the thermally generated diamines was sufficient for testing over a 37-day period. Analytical techniques that did not decompose the polymer matrix were applied. Emission rates for TDA and MDA isomers were less than the limit of quantitation (LOQ) of 0.008-0.07 µg.m-2.h-1. Migration was studied using samples of the same thermally treated foams over a 35-day period. Quantifiable migration of MDA from the MDI-based foam was only observed on Days 1 and 2. From Day 3 onward, migration rates were less than the LOQ. Quantifiable migration of TDA from the TDI-based foam rapidly decreased with time and was only observed on Days 1 thru 3. From Day 4 onward, migration rates were less than the LOQ. Theoretically, the migration rate should be inversely proportional to the square root of time (t) as t-0.5. This relationship was confirmed by the experimental data and enables extrapolating migration values to more extended time periods to conduct RAs.

Piezoresistive Behavior of a Conductive Polyurethane Based-Foam for Real-Time Structural Monitoring.

Smart flexible materials with piezoresistive property are increasingly used in the field of sensors. When embedded in structures, they would allow for in situ structural health monitoring and damage assessment of impact loading, such as crash, bird strikes and ballistic impacts; however, this could not be achieved without a deep characterization of the relation between piezoresistivity and mechanical behavior. The aim of this paper is to study the potential use of the piezoresistivity effect of a conductive foam made of a flexible polyurethane matrix filled with activated carbon for integrated structural health monitoring (SHM) and low-energy impact detection. To do so, polyurethane foam filled with activated carbon, namely PUF-AC, is tested under quasi-static compressions and under a dynamic mechanical analyzer (DMA) with in situ measurements of its electrical resistance. A new relation is proposed for describing the evolution of the resistivity versus strain rate showing that a link exists between electrical sensitivity and viscoelasticity. In addition, a first demonstrative experiment of feasibility of an SHM application using piezoresistive foam embedded in a composite sandwich structure is realized by a low-energy impact (2 J) test.

Solid-Phase Spectrometric Determination of Organic Thiols Using a Nanocomposite Based on Silver Triangular Nanoplates and Polyurethane Foam.

Adsorption of silver nanoparticles on polymers may affect the processes in which they participate, adjusting the analytical characteristics of methods for the quantitation of various substances. In the present study, a composite material based on silver triangular nanoplates (AgTNPs) and polyurethane foam was proposed for chemical analysis. The prospects of its application for the solid-phase/colorimetric determination of organic thiols were substantiated. It was found that aggregation of AgTNPs upon the action of thiols is manifested by a decrease in the AgTNPs' localized surface plasmon resonance band and its significant broadening. Spectral changes accompanying the process can be registered using household color-recording devices and even visually. Four thiols differing in their functional groups were tested. It was found that their limits of detection increase in the series cysteamine < 2-mercaptoethanol < cysteine = 3-mercaptopropionic acid and come to 50, 160, 500, and 500 nM, respectively. The applicability of the developed approach was demonstrated during the analysis of pharmaceuticals and food products.

Sustainable treatment of sewage sludge via plasma-electrolytic liquefaction for bio-friendly production of polyurethane foam.

Safe and green disposal or utilization of sewage sludge (SS) has attracted significant attention as SS is increasingly produced worldwide and emerges as an environmental burden if without proper treatment. In this study, efficient and sustainable treatment of SS was achieved using plasma-electrolytic liquefaction (PEL) with alkaline catalysts including sodium hydroxide (NaOH), sodium carbonate (Na2CO3), and sodium acetate (NaAc) and renewable solvents including polyethylene glycol (PEG) 200 and glycerol. Furthermore, the obtained bio-oil with abundant hydroxyl groups could partially replace polyols derived from fossil energy to synthesize bio-based polyurethane foams (BPUFs) for oil adsorption. The results showed that the Na2CO3 catalyst exhibited better performance and yielded bio-oil with a higher heating value (HHV) of 26.26 MJ/kg, very low nitrogen content (0.14%) and metal ions, and a nearly neutral pH of 7.41, under the optimized conditions. Compared with conventional oil bath liquefaction, PEL can significantly improve the liquefaction efficiency, promote the transfer of metal ions in SS to the solid residue (SR), and facilitate the transfer of nitrogen to the gas phase and SR, thereby upgrading the bio-oil to a certain extent. The BPUFs showed excellent oil adsorption capacity, reusability, and desorption and can play an important role in combating oil spills. The PEL method may provide a green avenue for SS valorization and the comprehensive utilization of the obtained products.

Study on the Flame Retardancy of Rigid Polyurethane Foam with Phytic Acid-Functionalized Graphene Oxide.

A rigid polyurethane foam (RPUF) composite was prepared by compounding phytic acid (PA)-functionalized Graphite oxide (PA-GO) with flame-retardant poly (Ammonium phosphate) (APP) and expandable graphite (EG). The effects of PA-GO on the thermal, flame-retardant, and mechanical properties of RPUF were studied using a thermogravimetric analyzer, a limiting oxygen index (LOI) tester, a UL-94 vertical combustion tester, a cone calorimeter, scanning electron microscopy, and a universal tensile testing machine. The results indicated that there was a significant synergistic flame-retardant effect between PA-GO and the intumescent flame retardants (IFR) in the RPUF matrix. Compared with RPUF-1, the addition of 0.3 wt% PA-GO could increase LOI from 25.7% to 26.5%, increase UL-94 rating from V-2 to V-0, and reduce the peak heat release rate (PHRR) and total heat release rate (THR) by 28.5% and 22.2%, respectively. Moreover, the amount of residual char increased from 22.2 wt% to 24.6 wt%, and the char layer was continuous and dense, with almost no holes. Meanwhile, the loss of mechanical properties was apparently lightened.

Advancements in Flame-Retardant Systems for Rigid Polyurethane Foam.

The amplified employment of rigid polyurethane foam (RPUF) has accentuated the importance of its flame-retardant properties in stimulating demand. Thus, a compelling research report is essential to scrutinize the recent progression in the field of the flame retardancy and smoke toxicity reduction of RPUF. This comprehensive analysis delves into the conventional and innovative trends in flame-retardant (FR) systems, comprising reactive-type FRs, additive-type FRs, inorganic nanoparticles, and protective coatings for flame resistance, and summarizes their impacts on the thermal stability, mechanical properties, and smoke toxicity suppression of the resultant foams. Nevertheless, there are still several challenges that require attention, such as the migration of additives, the insufficient interfacial compatibility between flame-retardant polyols or flame retardants and the RPUF matrix, and the complexity of achieving both flame retardancy and mechanical properties simultaneously. Moreover, future research should focus on utilizing functionalized precursors and developing biodegradable RPUF to promote sustainability and to expand the applications of polyurethane foam.

Feasibility of nasal bridge pressure injury prevention using a protective dressing and the Halyard Fluidshield® N95 mask in a COVID-positive environment.

The purpose of this study was to prevent nasal bridge pressure injury among fit-tested employees, secondary to long-term wear of the N95 mask during working hours. A prospective, single-blinded, experimental cohort design. Participants were enrolled using the convenience sampling methods and randomisation was utilised for group assignment. Eligibility was determined by a COVID Anxiety Scale score and non-COVID clinical assignment. Participants with a history of previous skin injury or related condition were excluded. The experimental group was assigned Mepilex Lite® and the control group used Band- Aid®. Formal skin evaluations were done by Nurse Specialists who are certified in wound and ostomy care by the Wound, Ostomy, Continence, Nursing Certification Board (WOCNCB®). Fit test logs were provided to participants to measure subjective user feedback regarding mask fit and level of comfort. The results of this feasibility trial are promising in supporting the use of a thin polyurethane foam dressing as a safe and effective dressing to apply beneath the N95 mask. Additional research is needed to validate results due to limited data on efficacy and safety of the various barrier dressings as a potential intervention to prevent skin breakdown to the nasal bridge.

Safer Polyurethane Foams with Cyclic Carbonates.

Polyurethanes (PUs) are a class of materials usually synthesized from isocyanates, diols, and water. Water is essential for producing carbon dioxide (CO2 ) which is used for the self-blowing of the foams. Due to safety concerns with the production of isocyanates, alternative chemistries have been evaluated and cyclic carbonate systems have shown great promise. In a recent advancement by Bourguignon, Grignard, and Detrembleur, a cyclic carbonate and diamine system is capable of generating CO2 for self-blowing through hydrolysis of the carbonate-based monomer. The authors demonstrate that with a simple variation of the diamine monomer a wide range of physical and thermo-mechanical properties were achievable. This work represents a significant step towards safer and more environmentally friendly PUs.

Management of esophageal perforations in infants by endoscopic vacuum therapy: a single center case series.

BACKGROUND: Endoscopic vacuum therapy (EVT) has become a standard treatment method for esophageal perforations in adults. However, experience with EVT in infants is scarce. In this retrospective case series, we report on four very young infants who were successfully treated with EVT for esophageal perforations of different etiology. METHODS: Four infants were diagnosed with esophageal perforations on day 7, 32, 35 and 159 of life, respectively. The youngest one was prematurely born in the 31st week of pregnancy weighing 980 g only. Three infants had perforations due to foreign body insertion (nasogastric tube or pulling through of percutaneous endoscopic gastrostomy (PEG) tube through the esophagus). One child had an anastomotic dehiscence after Foker's surgery for atresia. In three children EVT was applied as first-line therapy for perforation, in one child EVT was a rescue therapy due to persisting leakage after surgical closure involving thoracotomy. Depending on the esophageal diameter, either an open-pore drainage film or polyurethane sponge was attached to a single-lumen 8 Fr suction catheter, endoscopically (or fluoroscopically by wire-guidance) placed into the esophagus (intraluminal EVT) and supplied with continuous negative pressure (ranging between 75 and 150 mmHg). The EVT system was exchanged twice per week. RESULTS: Complete closure of the perforation/leakage could be achieved in all four infants (100%) after 22 days of continuous EVT (median value; range 7-39) and 4.5 EVT exchanges (median value; range 1-12). No serious adverse events occurred. CONCLUSIONS: EVT is an effective and safe addition to our therapeutic armamentarium in the management of esophageal perforations irrespective of its etiology. Here we prove the feasibility of EVT even in very young infants. The use of an extra thin vacuum open-pore drainage film is helpful to cope with the small esophageal diameter. EVT settings and exchange rates similar to those known from adult treatment were used.

Toluene diisocyanate occupational exposure data in the polyurethane industry (2005-2020): A descriptive summary from an industrial hygiene perspective.

This article provides an overview of toluene diisocyanate (TDI) workplace air concentration data. Data were collected between 2005-2020 in workplaces across the United States, Canada, and the European Union by a number of different organizations, primarily using the sampling procedures published in OSHA Methods 42 and 5002. The data were then collated and organized by the International Isocyanate Institute. Air samples were collected from several market segments, with a large portion of the data (87%) from the flexible foam industry. The air samples (2534 in total) were categorized into "area" or "personal," and the personal samples were subcategorized into "task," "short term," and "long term." Most of the air sample concentrations (87%) were less than 5 ppb. However, the presence of airborne TDI greater than 5 ppb indicated the importance of respiratory protection in some situations; therefore, respirator use patterns were studied and summarized. Additionally, this article provides a summary of air sample concentrations at different flexible foam manufacturing job roles. The information on air sampling concentrations and respiratory protection during TDI applications collected in this paper could be useful for product stewardship and industrial hygiene purposes in the industries studied.