Synthesis of New Glycine-Based Polymers and their Thermoresponsive Behavior in Water.

In this work, new glycine-derived polymers are developed that exhibit thermoresponsive properties in water. Therefore, a series of monomers containing one, two, or three amide functional groups and one terminal cyanomethyl group is synthesized. The resulting homopolymers, obtained by free radical polymerization (FRP) and reversible addition fragmentation chain transfer (RAFT) polymerization, display a sharp and reversible upper critical solution temperature (UCST)-type phase transition in water. Additionally, it is shown that the cloud point (TCP) can be adjusted over more than 60 °C by the number of glycyl groups present in the monomer structure and by the polymer's molar mass. These novel thermoresponsive polymers based on cyanomethylglycinamide enrich the range of nonionic UCST polymers and are promising to find applications in various fields.

UCST-Type Soluble Immobilized Cellulase: A New Strategy for the Efficient Degradation and Improved Recycling Performance of Wastepaper Cellulose.

This paper reports an innovative study that aims to address key issues in the efficient recycling of wastepaper cellulose. The research team utilized the temperature-responsive upper critical solution temperature (UCST) polymer P(NAGA-b-DMA) in combination with the LytA label's affinity for choline analogs. This innovative approach enabled them to successfully develop a novel soluble immobilized enzyme, P(NAGA-b-DMA)-cellulase. This new enzyme has proven highly effective, significantly enhancing the degradation of wastepaper cellulose while demonstrating exceptional stability. Compared with the traditional insoluble immobilized cellulase, the enzyme showed a significant improvement in the pH, temperature stability, recycling ability, and storage stability. A kinetic parameter calculation showed that the enzymatic effectiveness of the soluble immobilized enzyme was much better than that of the traditional insoluble immobilized cellulase. After the immobilization reaction, the Michaelis constant of the immobilized enzyme was only increased by 11.5%. In the actual wastepaper degradation experiment, the immobilized enzyme was effectively used, and it was found that the degradation efficiency of wastepaper cellulose reached 80% of that observed in laboratory conditions. This novel, thermosensitive soluble immobilized cellulase can efficiently catalyze the conversion of wastepaper cellulose into glucose under suitable conditions, so as to further ferment into environmentally friendly biofuel ethanol, which provides a solution to solve the shortage of raw materials and environmental protection problems in the paper products industry.

Effect of Molecular Weight on Phase Equilibrium in the Polystyrene-Poly(methyl methacrylate) System.

Data on the solubility of oligomer polystyrene (PS) and poly(methyl methacrylate) (PMMA) of various molecular weights have been obtained. The binodal and spinodal curves of the phase state diagram with the upper critical solution temperature (UCST) are constructed through simulation within the framework of the Flory-Huggins theory. The influence of the molecular weight of polymers on the contribution to their mixing has been compared, and correlation curves have been plotted. The interaction parameters were calculated and the mixing thermodynamics of the components was evaluated. The largest contribution was made by the entropy component. Also, it has been shown using IR spectroscopy that there is no interaction between the functional groups of polystyrene and poly(methyl methacrylate) in a homogeneous mixture.

Thermo-Reversible Cellulose Micro Phase-Separation in Mixtures of Methyltributylphosphonium Acetate and γ-Valerolactone or DMSO.

We have identified cellulose solvents, comprised of binary mixtures of molecular solvents and ionic liquids that rapidly dissolve cellulose to high concentration and show upper-critical solution temperature (UCST)-like thermodynamic behaviour - upon cooling and micro phase-separation to roughly spherical microparticle particle-gel mixtures. This is a result of an entropy-dominant process, controllable by changing temperature, with an overall exothermic regeneration step. However, the initial dissolution of cellulose in this system, from the majority cellulose I allomorph upon increasing temperature, is also exothermic. The mixtures essentially act as 'thermo-switchable' gels. Upon initial dissolution and cooling, micro-scaled spherical particles are formed, the formation onset and size of which are dependent on the presence of traces of water. Wide-angle X-ray scattering (WAXS) and 13 C cross-polarisation magic-angle spinning (CP-MAS) NMR spectroscopy have identified that the cellulose micro phase-separates with no remaining cellulose I allomorph and eventually forms a proportion of the cellulose II allomorph after water washing and drying. The rheological properties of these solutions demonstrate the possibility of a new type of cellulose processing, whereby morphology can be influenced by changing temperature.

Thermoresponsive Ionic Liquid/Water Mixtures: From Nanostructuring to Phase Separation.

The thermodynamics, structures, and applications of thermoresponsive systems, consisting primarily of water solutions of organic salts, are reviewed. The focus is on organic salts of low melting temperatures, belonging to the ionic liquid (IL) family. The thermo-responsiveness is represented by a temperature driven transition between a homogeneous liquid state and a biphasic state, comprising an IL-rich phase and a solvent-rich phase, divided by a relatively sharp interface. Demixing occurs either with decreasing temperatures, developing from an upper critical solution temperature (UCST), or, less often, with increasing temperatures, arising from a lower critical solution temperature (LCST). In the former case, the enthalpy and entropy of mixing are both positive, and enthalpy prevails at low T. In the latter case, the enthalpy and entropy of mixing are both negative, and entropy drives the demixing with increasing T. Experiments and computer simulations highlight the contiguity of these phase separations with the nanoscale inhomogeneity (nanostructuring), displayed by several ILs and IL solutions. Current applications in extraction, separation, and catalysis are briefly reviewed. Moreover, future applications in forward osmosis desalination, low-enthalpy thermal storage, and water harvesting from the atmosphere are discussed in more detail.

"Mesh free" autologous transobturator mid urethral sling placement for predominant stress urinary incontinence: A pilot study.

AIMS: To assess the efficacy and safety of autologous mid-urethral sling (MUS) in women with predominant stress urinary incontinence (SUI). MATERIALS AND METHODS: This prospective cohort study included adult women with predominant SUI seen in our urology clinic between January 2018 and March 2019. Patients with: negative cough stress test, history of prior incontinence surgery, urogenital malignancy, pelvic radiation, neurological disease, body mass index more than 40 kg/m2 , the presence of more than Stage I pelvic organ prolapse, active urinary tract infection, maximum flow rate less than 15 ml/sec, postvoid residual urine more than 100 ml, abdominal leak point pressure less than 60 cm of H2 O, and pregnant women were excluded. Eligible patients underwent a transobturator MUS procedure using rectus fascia as a sling. Before the procedure, patients filled the International Consultation on Incontinence Questionnaire-Female Lower Urinary Tract Symptom (ICIQ-FLUTS) and the Female Sexual Function Index (FSFI) questionnaire. Urinary outcomes were assessed at 3- and 12-months while sexual outcomes were assessed at 12-months. RESULTS: Thirty patients with median age of 44.5 years were included. All patients had a negative cough stress test during follow up. A significant improvement was noted in the ICIQ-FLUTS scale, bother scale, filling and incontinence subscales at 3 and 12 month follow-up. A significant improvement was also noted in the FSFI full scale score and FSFI domains of mean sexual desire, arousal and lubrication at 12 months follow-up. Two patients developed voiding dysfunction requiring urethral dilatation. CONCLUSION: Autologous transobturator MUS surgery appears to be safe and efficacious in the short term. More research is needed to clarify its role in the surgical management of SUI in women.

Thermoresponsive Polymers Based on Tertiary Amine Moieties.

Thermoresponsive polymers exhibiting unique reversible phase transition properties in aqueous solution in response to temperature stimuli have been extensively investigated. In the past two decades, thermoresponsive polymers based on tertiary amine moieties have achieved considerable progress and become an important family of thermoresponsive polymers, including tertiary amine functionalized poly((meth)acrylamide)s, poly((meth)acrylate)s, poly(styrene)s, poly(vinyl alcohol)s, and poly(ethylene oxide)s, which exhibit lower critical solution temperature and/or upper critical solution temperature in water or aliphatic alcohols. Their phase transition behavior can be modulated by the solution pH and CO2 due to the protonation of tertiary amine moieties in acidic condition and deprotonation in alkaline condition and the charged ammonium bicarbonate formed by the tertiary amine moieties and CO2 . The aim of this review is to summarize the recent progress in the thermoresponsive polymers based on tertiary amine moieties.

RAFT-Polymerized N-Cyanomethylacrylamide-Based (Co)polymers Exhibiting Tunable UCST Behavior in Water.

In this present work, the synthesis of a new family of upper critical solution temperature (UCST)-thermoresponsive polymers based on N-cyanomethylacrylamide (CMAm) is reported. It is demonstrated that the thermally initiated reversible addition fragmentation chain transfer (RAFT) polymerization of CMAm conducted in N,N-dimethylformamide (DMF) is well controlled. The homopolymer presents a sharp and reversible UCST-type phase transition in pure water with a very small hysteresis between cooling and heating cycles. It is demonstrated that the cloud point (TCP ) of poly(N-cyanomethylacrylamide) (PCMAm) is strongly molar mass dependent and shifts toward lower temperatures in saline water. Moreover, the transition temperature can be tuned over a large temperature range by copolymerization of CMAm with acrylamide or acrylic acid. The latter copolymers are both thermoresponsive and pH responsive. Interestingly, by this strategy sharp and reversible UCST-type transitions close to physiological temperature can be reached, which makes the copolymers extremely interesting candidates for biomedical applications.

Synthesis of Temperature-Responsive Polymers Containing Piperidine Carboxamide and N,N-diethylcarbamoly Piperidine Moiety via RAFT Polymerization.

In this study, poly(N-acryloyl-nipecotamide) (PNANAm), poly(N-acryloyl-isonipecotamide) (PNAiNAm), and poly(N-acryloyl-N,N-diethylnipecotamide) (PNADNAm) are synthesized as novel temperature-responsive polymers using reversible addition-fragmentation chain-transfer polymerization. Aqueous solutions of these three polymers are examined via temperature-dependent optical transmittance measurements. The PNANAm sample with a hydrophilic terminal group shows an upper critical solution temperature (UCST) in phosphate-buffered saline (PBS) when its molecular weight (Mn ) is 7600 or higher, whereas PNANAm (Mn < 7600) is soluble. The UCST is influenced by molecular weight and the polymer concentration. In contrast, PNANAm sample with nonionic terminal group shows UCST, when Mn is below 7600, suggesting that the terminal nonionic group possibly increases UCST of PNANAm. The urea addition experiment suggests that the driving force for expression of UCST of PNANAm is the formation of inter-and intramolecular hydrogen bonds among the polymer chains. PNAiNAm is soluble in PBS but exhibits an UCST in an appropriate concentration of ammonium sulfate. In contrast, PNADNAm exhibits a lower critical solution temperature. Comparing the chemical structure of these polymers and their phase transition behaviors suggests that the carboxamide group position in the piperidine ring could determine the UCST expression. These results could help design temperature-responsive polymers with a desired the cloud point temperature.

Structural Engineering and Optimization of Zwitterionic Salts for Expeditious Discovery of Thermoresponsive Materials.

This work reported the discovery of N-triflimide (NTf)-based zwitter-ionic liquids (ZILs) that exhibit UCST-type phase transitions in water, and their further structural optimization in fine-tuning polarity to ultimately afford newfangled thermosensitive materials carrying attractive and biocompatible Tc values that clearly demonstrated the true value of the tunability of ZIL structure. This research established that with non-aromatic, acyclic ZILs as small-molecule thermoresponsive materials, their mixing and de-mixing with water triggered by temperatures are entirely reversible.

Constrained thermoresponsive polymers - new insights into fundamentals and applications.

In the last decades, numerous stimuli-responsive polymers have been developed and investigated regarding their switching properties. In particular, thermoresponsive polymers, which form a miscibility gap with the ambient solvent with a lower or upper critical demixing point depending on the temperature, have been intensively studied in solution. For the application of such polymers in novel sensors, drug delivery systems or as multifunctional coatings, they typically have to be transferred into specific arrangements, such as micelles, polymer films or grafted nanoparticles. However, it turns out that the thermodynamic concept for the phase transition of free polymer chains fails, when thermoresponsive polymers are assembled into such sterically confined architectures. Whereas many published studies focus on synthetic aspects as well as individual applications of thermoresponsive polymers, the underlying structure-property relationships governing the thermoresponse of sterically constrained assemblies, are still poorly understood. Furthermore, the clear majority of publications deals with polymers that exhibit a lower critical solution temperature (LCST) behavior, with PNIPAAM as their main representative. In contrast, for polymer arrangements with an upper critical solution temperature (UCST), there is only limited knowledge about preparation, application and precise physical understanding of the phase transition. This review article provides an overview about the current knowledge of thermoresponsive polymers with limited mobility focusing on UCST behavior and the possibilities for influencing their thermoresponsive switching characteristics. It comprises star polymers, micelles as well as polymer chains grafted to flat substrates and particulate inorganic surfaces. The elaboration of the physicochemical interplay between the architecture of the polymer assembly and the resulting thermoresponsive switching behavior will be in the foreground of this consideration.

A Synthetic, Transiently Thermoresponsive Homopolymer with UCST Behaviour within a Physiologically Relevant Window.

Interactive materials that can respond to a trigger by changing their morphology, but that can also gradually degrade into a fully soluble state, are attractive building blocks for the next generation of biomaterials. Herein, we design such transiently responsive polymers that exhibit UCST behaviour while gradually losing this property in response to a hydrolysis reaction in the polymer side chains. The polymers operate within a physiologically relevant window in terms of temperature, pH, and ionic strength. Whereas such behaviour has been reported earlier for LCST systems, it is at present unexplored for UCST polymers. Furthermore, we demonstrate that, in contrast to LCST polymers, in aqueous medium the UCST polymer forms a coacervate phase below the UCST, which can entrap a hydrophilic model protein, as well as a hydrophobic dye. Because of their non-toxicity, we also provide in vivo proof of concept of the use of this coacervate as a protein depot, in view of sustained-release applications.

Let There be Light: Polymeric Micelles with Upper Critical Solution Temperature as Light-Triggered Heat Nanogenerators for Combating Drug-Resistant Cancer.

Complete drug release and efficient drug retention are two critical factors in reversing drug resistance in cancer therapy. In this regard, polymeric micelles with an upper critical solution temperature (UCST) are designed as a new exploration to reverse drug resistance. The amphiphilic UCST-type block copolymers are used to encapsulate photothermal agent IR780 and doxorubicin (DOX) simultaneously. The integrated UCST-type drug nanocarriers show light-triggered multiple synergistic effects to reverse drug resistance and are expected to kill three birds with one stone: First, owing to the photothermal effect of IR780, the nanocarriers will be dissociated upon exposure to laser irradiation, leading to complete drug release. Second, the photothermal effect-induced hyperthermia is expected to avoid the efflux of DOX and realize efficient drug retention. Last but not least, photothermal ablation of cancer cells can be achieved after laser irradiation. Therefore, the UCST-type drug nanocarriers provide a new strategy in reversing drug resistance in cancer therapy.

Tuning the Phase Transition from UCST-Type to LCST-Type by Composition Variation of Polymethacrylamide Polymers.

Polymethacrylamide copolymers with hydrophobic N-substituted acrylamides, such as N-cyclohexylacrylamide and N-tert-butylacrylamide, are rare examples of polymers showing composition-dependent thermoresponsive behavior in water. They show unexpected behavior different from the conventional copolymers of a thermoresponsive polymer with hydrophobic comonomers. On increasing the amount of the hydrophobic comonomer in the polymer, there is a change from UCST-type phase behavior to complete solubility, followed by compositions showing LCST-type transition and insolubility in water (U-S-L-I-type change). At 50 mol% of less hydrophobic N-tert-butyl acrylamide (logP 0.87) in contrast to ≈25 mol% of N-cyclohexylacrylamide (logP 1.51), the broad UCST-type transition of polymethacrylamide is turned to LCST-type transitions with very narrow hysteresis in water and PBS buffer. The use of H-bond and water-structure breaker showed the role of H-bonding and hydrophobic interactions in phase transitions of UCST-type and LCST-type, respectively. This work is an important add-on to the infant field of nonionic polymers of UCST-type.

Hydrogels with Dual Thermoresponsive Mechanical Performance.

Dual thermoresponsive chemical hydrogels, combining poly(N-isopropylacrylamide) side-chains within a poly(N-acryloylglycinamide) network, are designed following a simple and versatile procedure. These hydrogels exhibit two phase transitions both at low (upper critical solution temperature) and high (lower critical solution temperature) temperatures, thereby modifying their swelling, rheological, and mechanical properties. These novel thermo-schizophrenic hydrogels pave the way for the development of thermotoughening wet materials in a broad range of temperatures.

RAFT Synthesis in Water of Cationic Polyelectrolytes with Tunable UCST.

Cationic polyelectrolytes showing an upper critical solution temperature (UCST) are synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization in water at a temperature well above the UCST. The polymerization is well controlled by the RAFT process, with excellent pseudo-first-order kinetics. The cloud point is highly dependent on the polyelectrolyte concentration, molecular weight, and presence of added electrolyte. Alkylation of a neutral polymer is also conducted to obtain polyelectrolytes with different hydrophobic groups, which are shown to increase the cloud point.

A novel nanocomposite hydrogel with precisely tunable UCST and LCST.

Novel thermosensitive nanocomposite (NC) hydrogels consisting of organic/inorganic networks are prepared via in situ free radical polymerization of 2-(2-methoxyethoxy) ethyl methacrylate (MEO2 MA) and oligo(ethylene glycol) methacrylate (OEGMA) in the presence of inorganic cross-linker clay in aqueous solution. The obtained clay/P(MEO2 MA-co-OEGMA) hydrogels exhibit double volume phase transition temperatures, an upper critical solution temperature (UCST), and a lower critical solution temperature (LCST), which can be controlled between 5 and 85 °C by varying the fraction of OEGMA units and the weight percentage of cross-linker clay. These new types of NC hydrogels with excellent reversible thermosensitivity are promising for temperature-sensitive applications such as smart optical switches.

Tuning the LCST and UCST thermoresponsive behavior of poly(N,N-dimethylaminoethyl methacrylate) by electrostatic interactions with trivalent metal hexacyano anions and copolymerization.

Poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA) has been reported to show both upper critical solution temperature (UCST) and lower critical solution temperature (LCST) behavior in presence of trivalent metal hexacyano anions, which is attractive for the development of smart materials. In this communication, the influence of the double thermoresponsive behavior of PDMAEMA driven by electrostatic interactions is investigated by comparing systems with [Co(CN)6 ](3-) , [Fe(CN)6 ](3-) , and [Cr(CN)6 ](3-) as trivalent anions. Furthermore, tuning of double thermoresponsive behavior of PDMAEMA by incorporating hydrophilic or hydrophobic comonomers is also discussed in the presence of [Fe(CN)6 ](3-) as trivalent ion.

Preparation of Thermo-Responsive Poly(ionic liquid)s-Based Nanogels via One-Step Cross-Linking Copolymerization.

In this study, thermo-responsive polymeric nanogels were facilely prepared via one-step cross-linking copolymerization of ethylene glycol dimethacrylate/divinylbenzene and ionic liquid (IL)-based monomers, 1,n-dialkyl-3,3'-bis-1-vinyl imidazolium bromides ([CnVIm]Br; n = 6, 8, 12) in selective solvents. The results revealed that stable and blue opalescent biimidazolium (BIm)-based nanogel solutions could be obtained without any precipitation when the copolymerizations were conducted in methanol. Most importantly, these novel nanogels were thermo-response, and could reversibly transform to precipitation in methanol with temperature changes. Turbidity analysis and dynamic light scatting (DLS) measurement illustrated that PIL-based nanogel solutions presented the phase transform with upper critical solution temperature (UCST) in the range of 5-25 °C. The nanogels were characterized using Fourier transform infrared (FTIR), thermogravimetric analyses (TGA), and scanning electron microscopy (SEM). In addition, BIm-based nanogels could also be used as highly active catalysts in the cycloaddition reaction of CO2 and epoxides. As a result, our attributes build a robust platform suitable for the preparation of polymeric nanomaterials, as well as CO2 conversion.

Influence of cyclodextrin on the UCST- and LCST-behavior of poly(2-methacrylamido-caprolactam)-co-(N,N-dimethylacrylamide).

The monomer 2-methacrylamido-caprolactam (4) was synthesized from methacryloyl chloride (3) and racemic α-amino-ε-caprolactam (2). Copolymerization of 4 with N,N-dimethylacrylamide (5) was carried out by a free-radical mechanism using 2,2'-azobis(2-methylpropionitrile) (AIBN) as an initiator. The new copolymers show a lower critical solution temperature (LCST) in water and an upper critical solution temperature (UCST) in ethanol, 1-propanol, and 1-butanol. The solubility properties of the copolymers can be influenced significantly by the addition of randomly methylated ß-cyclodextrin (CD). The complexation of the copolymers with CD, was confirmed by the use of ROESY-NMR-spectroscopy.