Microcomputed tomographic evaluation of 6 NiTi files on the pericervical dentin and the smallest dentin thickness zones in mesial root canals of mandibular molars: an in vitro study.

OBJECTIVE: The aim of this study was to evaluate six files on the pericervical dentin (PCD) and the smallest dentin thickness zones (SDTZ) in mesial root canals of mandibular molars. MATERIALS AND METHODS: Sixty mandibular molars with two mesial canals and Vertucci configuration were aleatory allocated in 6 experimental groups of 10 molars and 20 root canals. Specimens were scanned before instrumentation using the SkyScan 1275 (Bruker microCT, Kontich, Belgium). Group 1 was treated with WaveOne Gold (WG), group 2 with Reciproc Blue (RB), group 3 with TRUShape (TS), group 4 with XP-endo Shaper (XP), group 5 with iRace (IR), and group 6 with TruNatomy (TN). After instrumentation, the molars were scanned again and the images recorded were reconstructed with the NRecon v.1.7 (Bruker micro-CT) and analyzed with CTAn v.1.20.8 software (Bruker micro-CT) quantifying the changes produced in the surface, volume, structure thickness, SMI, and centroids at the Pericervical Dentin area of the root canals (PCD) located from the root canal orifices at the floor of the pulp chamber to 4 mm in the apical direction, and the changes in the Smallest Dentin Thickness Zones (SDTZ) located (from the furcation to 4 mm and 7 mm in the apical direction. The data obtained were compared using Wilcoxon and ANOVA with a 5% significance level. RESULTS: XP and TN were similar in all the parameters (P >.05) at the PCD, but TN showed significant differences from WG, RB, TS, and IR (P <.05), while XP showed significant differences from WG (P <.05) in volume, surface, and structure thickness. Regarding the changes in the SDTZ, the amount of dentin removed was similar between the groups in both canals at the middle 1/3, at the cervical 1/3 for MB canals, and in ML canals for RB, TS, XP, IR, and TN (P>.05). The action of WG was significantly different from that of XP and TN in the cervical 1/3 of the ML canal (P <.05). CONCLUSIONS: XP and TN rotatory files with small taper and volume maintained better with minor changes at the PCD and SDTZ, while WG reciprocation file produced the largest change. All the files were maintained centered at the PCD, and their performances were safe with a minimal thickness higher 0.5 mm at the SDTZ, and without risk of perforation. TRIAL REGISTRATION: No clinical trials were indicated in this study. CLINICAL RELEVANCE: The choice of endodontic files is a relevant factor in the conservative performance of root canal treatments.

Effects of Access Cavity Design and Placement Techniques on Mineral Trioxide Aggregate Obturation Quality in Simulated Immature Teeth: A Micro-Computed Tomography Study.

Background and Objectives: In teeth with open apices, performing single session apexification is a challenging treatment due to the difficulty in handling mineral trioxide aggregate (MTA). Minimally invasive approaches in dentistry have also influenced the cavity designs in endodontics. Until now, different techniques have not been investigated in addition to manual condensation during the process of placing MTA in traditional (TradACs) or conservative (ConsACs) endodontic access cavities. The aim of this in vitro study was to compare and evaluate the obturation quality of MTA apical plugs placed with different techniques in TradACs or ConsACs. Materials and Methods: Sixty upper central teeth were divided into two main groups based on cavity design, and then each main group was further divided into three subgroups according to MTA placement techniques (n = 10): TradAC-manual, TradAC-manual + indirect ultrasonic activation, TradAC-manual + XP-endo Shaper (XPS), ConsAC-manual, ConsAC-manual + indirect ultrasonic activation, and ConsAC-manual + XPS. Subsequently, the porosity percentages in the MTA apical plug were analyzed using micro-computed tomography. The statistical analysis was performed using the Kruskal-Wallis H test and Mann-Whitney U test. Statistical significance was set at p < 0.05. Results: There were differences in volume of porosity percentages (%) according to cavity designs and MTA application techniques (p < 0.05). Except for the XPS group, more porosity was observed in ConsACs compared to TradACs. In TradACs, the significantly lowest open and total porosity was observed in the manual, ultrasonic, and XPS techniques, respectively. In ConsACs, the significantly lowest porosity was observed in the manual, XPS, and ultrasonic techniques, respectively (p < 0.05). Conclusions: In MTA obturation, cavity designs and application techniques had an impact on the MTA porosity. Creating an apical plug in ConsACs may result in more porosity compared to TradACs, especially when manual or indirect ultrasonic activation is preferred. Opting for the manual technique alone may be considered sufficient for controlling porosity for both TradACs and ConsACs.

Retreatment of XP-endo Shaper and R-Endo files in curved root canals.

OBJECTIVES: To compare the retreatment efficiency of XP-endo Shaper and R-Endo files in curved root canals using ImageJ software. METHODS: Forty extracted mandibular first molars with curved mesial canals (25°-35°) were chosen. Access cavities, preparation and obturation of root canals were performed. Roots were randomly distributed into two groups corresponding to the retreatment files used. Group 1 retreated with XP-endo Shaper file, and group 2 retreated with R-Endo files. Each root was sectioned and photographed. ImageJ software was used to estimate the percentage of residual filling material that existed on the three root canal segments. Mann-Whitney U and the Kruskal-Wallis tests were used to compare the percentages of residual filling material between the teeth segments (P < .05). RESULTS: The R-Endo group showed a significantly higher median percentage of residual filling material than the XP-endo Shaper group. In both groups, the coronal segments had the highest median of the residual filling material, followed by the middle and apical segments. CONCLUSION: XP-endo Shaper is significantly more effective than R-Endo in removing root canal filling materials in the coronal, middle, and apical segments.

Incidence of Post-Operative Pain following a Single-Visit Pulpectomy in Primary Molars Employing Adaptive, Rotary, and Manual Instrumentation: A Randomized Clinical Trial.

Background and Objectives. To differentiate the intensity of postoperative pain after primary molar pulpectomy employing manual instrumentation versus two single-file systems with different kinetics (the XP-Endo shaper file with adaptive instrumentation vs. the Kedo-SG blue file with continuous rotation instrumentation). Materials and Methods. This three-arm, single-blind, randomized clinical trial included assessing 75 healthy children between 4 to 9 years who required pulpectomy for primary molars (mandibular first and second). The three groups each had an equal number of children. Children in Group 1 had their teeth instrumented with the XP-endo Shaper, children in Group 2 had their teeth instrumented with the Kedo-SG Blue file, and children in Group 3 had their teeth instrumented manually using K-files. The degree of postoperative pain was measured using a four-point pain scale at 6-, 12-, 24-, 48-, and 72-h following therapy. Each participant's parent received five flashcards with four faces and a word characterizing each face. The data were analyzed using Kruskal-Wallis and chi-square tests. The level of significance was set to 5%. Results. During the follow-up period, there was a significant difference in postoperative pain intensity between the three groups. The XP-endo shaper was associated with considerably decreased post operative at the 6- and 12-h interval followed by Kedo-SG. The highest post-operative discomfort across the groups was related to the patients who underwent manual instrumentation. Conclusion. In comparison to rotary and manual instrumentation, postoperative pain severity was reduced with adaptive instrumentation.

Adaptive instrumentation of root canals in primary teeth using XP-endo shaper: a case series.

Dental caries is indeed the biggest cause of tooth loss, particularly in the primary dentition. In primary teeth with carious pulp involvements, endodontic intervention in the form of pulpotomy (removal of only the coronal pulp) or pulpectomy (removal of coronal and radicular pulp) is advocated. Pulpectomy can be laborious and time-consuming, especially when using traditional hand endodontic files to shape root canals. In paediatric dentistry, motorised nickel-titanium (Ni-Ti) rotary instrumentation has proved significant in enhancing the quality of pulpectomy. In primary dentition, however, these files may leave more than half of the root canals unaltered by instrumentation, just as they do in permanent dentition. The XP-endo® Shaper is a revolutionary heat-dependent endodontic file that uses an asymmetrical rotating motion to address the maximum area of the root canal space, resulting in anatomic root canal instrumentation. The case series describes the use of this novel XP-endo® Shaper file for anatomic root canal instrumentation in primary molars with irreversible pulpitis. The purpose is to demonstrate the efficacy and advantages of this cutting-edge endodontic treatment method. This case series can be an informative resource for other endodontic specialists by providing a practical illustration of how adaptable instrumentation can be utilised to successfully treat a patient. In conclusion, The use of the XP-endo Shaper® for pulpectomy demonstrated faster and instrumentation that was confined with the original shape of the canals, although further research is required to fully utilise these findings.

Biofilm elimination from infected root canals using four different single files.

INTRODUCTION: Enterococcus faecalis (E. faecalis) is the most commonly isolated bacterium from infected root canals. It is found in the form of a biofilm, which makes it more resistant to antimicrobials, and requires optimal chemomechanical strategies to maximize root canal disinfection. AIM: To evaluate the efficacy of 4 different endodontic file systems against E. faecalis biofilm growth in root canals using colony-forming units per milliliter (CFU/mL) and scanning electron microscope (SEM). METHODS: Eighty-five extracted human mandibular premolars with straight root canals and apical diameters not larger than the #15 K-file were randomly selected. After performing a pilot study (n = 15) to determine the ideal incubation period for E. faecalis biofilm development, sixty-five root canals were infected with E. faecalis, incubated for 3 weeks, and then mechanically prepared using one of four single files (XP-endo Shaper, Hyflex EDM, One Curve, and Fanta. AFTM F One) (n = 15). Five infected root canals were excluded for the positive control. Five non-contaminated root canals were included for the negative control. Samples were collected using sterile paper points pre- and post-instrumentation to determine the bacterial load (CFU/mL). Root canals from each group were topographically evaluated at the coronal, middle, and apical segments using scanning electron microscope (SEM). Bacterial reduction data were estimated and statistically analyzed by Kruskal-Wallis and Mann-Whitney U tests (post hoc test) (P ≤ .05). RESULTS: XP-endo Shaper, Hyflex DEM, and One Curve significantly could eradicate E. faecalis biofilms in infected root canals with no significant difference among them compared to Fanta. AF™ F One. CONCLUSION: None of the systems were capable of completely eliminating biofilms. XP-endo Shaper, Hyflex EDM, and One Curve mechanically eliminated E. faecalis biofilms compared to Fanta. AF™ F One from infected root canals.

Impact of agitation/activation strategies on the antibiofilm potential of sodium hypochlorite/etidronate mixture in vitro.

BACKGROUND: To investigate the effect of a rotary agitation method or ultrasonically activated irrigation on the antibiofilm effect of a mixture of sodium hypochlorite (NaOCl) and etidronate (1-hydroxyethylidene-1,1-bisphosphonate, HEBP) using a dual-species biofilm model in root canal system. METHODS: Mature dual-species biofilms of Enterococcus faecalis and Streptococcus gordonii were formed in root canals of mandibular premolars. Teeth were randomly allotted (n = 12) to group 1, XP-endo Finisher (XPF); group 2, ultrasonically activated irrigation (UAI); group 3, syringe-and-needle irrigation (SNI). In all groups, canals were instrumented with a rotary instrument (XP-endo Shaper) prior to irrigant agitation/activation. A mixture containing 2.5% NaOCl and 9% HEBP was used throughout the experiment. Bacterial counts from the canal were determined using qPCR before preparation (S1), after preparation (S2), and after final irrigation agitation/activation (S3). Bacterial viability within the dentinal tubules in the coronal, middle and apical root-thirds was quantified using confocal microscopy after Live/Dead staining. The bacterial counts and viability were compared between groups using one-way ANOVA and post-hoc Tukey's tests. Paired t-test was used to compare the bacterial counts within groups. RESULTS: Instrumentation alone could significantly reduce the microbial counts in all the groups (P < 0.0001). Subsequent agitation/activation resulted in significant microbial reduction only in XPF and UAI (P < 0.05), both of which reduced significantly more microbial counts than SNI (P < 0.05). Live/Dead staining revealed that XPF and UAI showed significantly greater percentage of dead bacteria within the dentinal tubules than SNI in the coronal third (P < 0.05); UAI resulted in the significantly highest percentage of dead bacteria in the middle third (P < 0.05); while there was no significant difference between the groups in the apical third (P > 0.05). CONCLUSIONS: When using the sodium hypochlorite/etidronate mixture for irrigation, final irrigant agitation/activation with XP-endo Finisher or ultrasonic can improve disinfection of the main root canal space and the dentinal tubules in the coronal third, while ultrasonically activated irrigation appears to exhibit better disinfection within dentinal tubules in the middle third.

Effect of XP-endo Shaper versus conventional rotary files on postoperative pain and bacterial reduction in oval canals with necrotic pulps: a randomized clinical study.

AIM: To assess postoperative pain and bacterial reduction following the use of XP-endo Shaper versus conventional rotary files in preparation of oval canals with necrotic pulps. METHODOLOGY: This superiority, parallel, randomized, double blinded clinical trial was conducted in the clinic of the Endodontic Department, Faculty of Dentistry, Cairo University, Egypt. Sixty single-canalled mandibular premolars with necrotic pulps were randomly assigned into two equal groups. Canals were instrumented using XP-endo Shaper files in the intervention group and iRaCe rotary files in the control group. Bacterial samples were taken before and after canal instrumentation. Incidence and severity of postoperative pain was assessed using a modified VAS after 6, 12, 24 h and daily for 5 days. A culture method was used to assess the number of bacterial colony forming units. Incidence of analgesic intake as well as flare-ups was recorded. Data were analysed using chi-square, Fisher Exact, Mann-Whitney, Independent t-test, and Spearman's correlation for pain and bacterial counts. RESULTS: The XP-endo Shaper compared with the iRaCe group was associated with a significantly lower incidence of postoperative pain at 6, 12, and 24 h (P = 0.039, 0.047, and 0.026, respectively), and severity of postoperative pain at 6 h (mean difference: 1.33, 95% CI: 0.307-2.352, P = 0.02), 12 h (mean difference: 1.1, 95% CI: 0.26-1.936, P = 0.007), 24 h (mean difference: 0.94, 95% CI: 0.178-1.701, P = 0.008) and 48 h (mean difference: 0.97, 95% CI: 0.192-1.747, P = 0.038). There was a significant decrease in bacterial count following canal instrumentation in both groups (P < 0.001) with no significant difference between them (mean difference: 0.83 × 105 , 95% CI: 0.336 × 105 -1.996 × 105 , P = 0.56). A weak correlation existed between postoperative pain severity and bacterial counts (P = 0.54). There was no significant difference in analgesic intake between the two groups (P = 0.085). Flare-ups occurred in 3.3% of teeth in the iRaCe group, while no flare-ups occurred in the XP-endo Shaper group. CONCLUSIONS: XP-endo Shaper was associated with a significantly lower frequency of postoperative pain for up to 24 h, and lower severity of postoperative pain for up to 48 h compared with iRaCe files. Both systems were equally effective in bacterial reduction from oval root canals with necrotic pulps.

The impact of minimally invasive root canal preparation strategies on the ability to shape root canals of mandibular molars.

AIM: To evaluate the use of a reduced taper endodontic instrument system (Bassi Logic™ .03 taper) and expandable heat-treated system (XP-endo Shaper) on the ability to shape canals in mandibular molars, by means of microcomputed tomography (micro-CT) analysis. The Reciproc system was used as the reference for comparison. METHODOLOGY: Twenty-four mandibular molars were scanned in a micro-CT, matched based on similar anatomical features and sorted into three groups (n = 8 per group), according to root canal preparation system: Bassi Logic™ .03, XP-endo Shaper and Reciproc. The teeth were mounted onto a mannequin and the pulp chambers were accessed with traditional access cavities. In Bassi Logic™ .03 and Reciproc groups, mesial canals were prepared with size 25, .03 taper or R25 (size 25, .08v taper) instruments and the distal root canal with size 25, .03 taper and size 40, .03 taper or R25 and R40 (size 40, .06v taper), respectively. In XP-endo Shaper groups, all root canals were prepared with XP-endo Shaper (size 30, .04v taper). After root canal preparation, the teeth were rescanned. The percentage of untouched canal areas and the percentage of removed dentine were evaluated separately for mesial and distal root canals. The data were analysed using one-way anova and Tukey tests (P < 0.05). RESULTS: The Bassi Logic™ .03 group was associated with a greater percentage of untouched canal areas when compared to XP-endo Shaper and Reciproc groups for mesial and distal root canals (P < 0.05), but no differences were found between XP-endo Shaper and Reciproc groups (P > 0.05). No significant difference was observed in the percentage of dentine removed amongst the groups for mesial and distal root canals (P > 0.05). CONCLUSION: The use of a reduced taper system (Bassi Logic™ .03) during root canal preparation resulted in a greater percentage of untouched canal areas when compared to XP-endo Shaper and Reciproc instruments. No differences were observed amongst the systems regarding the percentage of dentine removed.

Shaping ability of XP-endo Shaper and ProTaper Next in long oval-shaped canals: a micro-computed tomography study.

AIM: To evaluate the shaping ability of the single-file XP-endo Shaper system (XP-S; FKG Dentaire, La Chaux-de-Fonds, Switzerland) employing a different working time and of the multiple-file ProTaper Next system (Dentsply Sirona, Ballaigues, Switzerland) using micro-computed tomography (micro-CT) technology. METHODOLOGY: Twenty long oval-shaped canals in mandibular incisors were matched anatomically and scanned by micro-CT (Skyscan 1172; Bruker micro-CT, Kontich, Belgium). The canals were divided into two groups (n = 10) according to the canal preparation protocol: XP-endo Shaper (XP-S) with an extra 45 s of instrumentation and ProTaper Next (PTN X4). The images recorded before and after preparation were evaluated for morphometric measures of volume, surface area, structure model index and untouched walls. The data were compared statistically (Student's t-test for homogenous variances and Mann-Whitney test) between the two groups (XP-S and PTN X4) at α = 5%. RESULTS: Root canal preparation significantly increased all parameters (volume, surface area, structure model index and untouched walls) tested in each group (P < 0.05). There was no significant difference (P > 0.05) in the percentage increase of volume (107.50%-93.13%), surface area (27.74%-29.68%) or untouched canal wall (13.08%-11.74%) between XP-S and PTN X4, respectively. CONCLUSIONS: The XP-endo Shaper system (single-file) with an extra 45 s of instrumentation and the ProTaper Next system (multiple files) had a similar root canal shaping ability. Neither technique was able to fully prepare the long oval-shaped canals of mandibular incisors.

Influence of rotational speed and glide path on cyclic fatigue resistance of XP-endo shaper.

AIM: The aim of this study was to evaluate the effect of the different rotational speeds and creating a glide path on cyclic fatigue resistance of XP-endo Shaper® (XPS) (FKG Dentaire SA, La Chaux-de-Fonds, Switzerland) at intracanal temperature. MATERIALS AND METHODS: Ninety-six XPS files were divided into 6 groups [directly used at 1000 rpm (G1) or 3000 rpm (G4), with glide path at 1000 rpm (G2) or 3000 rpm (G4), without glide path at 1000 rpm (G3) and 3000 rpm (G6)]. All the instruments were rotated in a stainless-steel artificial canal with a 75° angle of curvature, 7.5 mm radius of curvature, and 1.3 mm inner diameter until the fracture occurred. The number of cycles to failure (NCF) and the length of the fractured (LF) segments were evaluated. Weibull analysis, one-way ANOVA, and Tukey multiple comparison tests were performed with the significance level set at 0.05. RESULTS: NCF of 3000 rpm groups was statistically higher than that of 1000 rpm groups (P < 0.05). And time to fracture was found statistically higher in 1000 rpm as compared to 3000 rpm. The mean LF of the instruments was statistically insignificant (P > 0.05). There was no statistical difference within the groups subjected at 1000 rpm and 3000 rpm files used with or without a glide path (P > 0.05). CONCLUSION: Within the limitations of this in vitro study, it was determined that XPS can be used safely even at 3000 rpm speed with or without glide path.

Shaping efficiency as a function of time of a new heat-treated instrument.

AIM: To assess the shaping ability of the new XP-endo Shaper instrument after different working times. METHODOLOGY: Ten mesial roots of mandibular molars were scanned in a micro-computed tomographic device and prepared using the XP-endo Shaper instrument up to the working length (WL) according to the manufacturer's recommendation. Then, each specimen was subjected to an extra 15, 30 and 45 s of active instrumentation at the WL. Postoperative scans were performed after canal preparation at each time-point. Then, the registered pre- and postoperative datasets were examined to evaluate the percentages of volume and surface area of the instrumented canal, surface area of noninstrumented canal areas and the volume of removed dentine. Repeated measures general linear model was used to compare the differences in either the increase or the reduction of the parameters amongst the time-points. Alpha-error was set at 5%. RESULTS: Extending the period of XP-endo Shaper active instrumentation at WL significantly influenced several parameters such as volume (P < 0.001) and surface area (P < 0.001) of the instrumented canal, surface area of noninstrumented canal areas (P < 0.001), and volume of removed dentine (P < 0.001). CONCLUSIONS: Extending the activation time of XP-endo Shaper instruments at WL resulted in a more comprehensive root canal preparation, increasing the volume and surface area of root canal preparation and the volume of removed dentine.

Influence of Temperature on the Cyclic Fatigue of Nickel-Titanium Instruments with Different Heat Treatments on Severely Curved Canals.

AIM: This study aims to investigate the influence of temperatures of 20 °C and 37 °C on the resistance to cyclic fatigue of NiTi instruments with different heat treatments, as tested in severely curved simulated canals. MATERIALS AND METHODS: Seventy-two instruments were distributed according to the temperature used (20 °C and 37 °C): XP-endo Shaper (30/0.01), ProDesign Logic (30/0.05), and iRaCe (30/0.04). The instruments were rotated freely until the occurrence of fracture inside an artificial severely curved stainless steel canal, which had a 90° angle of curvature and a curvature radius of 5 mm. Kolmogorov-Smirnov, Wilcoxon, ANOVA, and Kruskal-Wallis tests were performed. A p value of <0.05 was considered statistically significant. RESULTS: XP-endo Shaper instruments presented higher NCF values and time to failure compared with ProDesign Logic and iRaCe instruments at 20 °C and 37 °C (p < 0.001). CONCLUSION: Within the limitations of this study, the results show that the body temperature (37 °C) significantly lowers the resistance to cyclic fatigue of all instruments compared with 20 °C. CLINICAL SIGNIFICANCE: Body temperature is an important factor in the results of cyclic fatigue tests.

Torsional resistance of XP-endo Shaper at body temperature compared with several nickel-titanium rotary instruments.

AIM: To compare the torsional resistance of XP-endo Shaper (XPS; size 30, .01 taper, FKG Dentaire, La Chaux-de-Fonds, Switzerland) instruments at body temperature with TRUShape (TRS; size 30, .06 taper, Dentsply Tulsa Dental Specialties, Tulsa, OK, USA), ProFile Vortex (PV; size 30, .04 taper, Dentsply Tulsa Dental Specialties) and FlexMaster (FM; size 30, .04 taper, VDW GmbH, Munich, Germany) nickel-titanium rotary instruments. METHODOLOGY: A metal block with a square-shaped mould (5 mm × 5 mm × 5 mm) was positioned inside a glass container. Five millimetres of the tip of each instrument was held inside the metal block by filling the mould with a resin composite. The instruments were tested for torsional resistance in saline solution at 37 °C. Data were analysed using one-way analysis of variance (anova) and Tukey post hoc tests. The significance level was set at P < 0.05. RESULTS: FM had the greatest torsional resistance amongst the instruments tested (P < 0.001). There was no significant difference between FM and PV instruments (P = 0.211). The ranking for torsional resistance values was: FM > PV > TRS > XPS. CONCLUSIONS: FlexMaster and ProFile Vortex instruments were more resistant to torsional stress compared with TRUShape and XP-endo Shaper instruments. The manufacturing process used to produce XP-endo Shaper instruments did not enhance their resistance to torsional stress as compared with the other instruments.

Cyclic fatigue resistance of XP-endo Shaper compared with different nickel-titanium alloy instruments.

OBJECTIVE: The aims of this study were to assess and compare the resistance to cyclic fatigue of XP-endo Shaper (XPS; FKG Dentaire, La Chaux-de-Fonds, Switzerland) instruments with TRUShape (TRS; Dentsply Tulsa Dental Specialties, Tulsa, OK, USA), HyFlex CM (HCM; Coltene, Cuyahoga Falls, OH, USA), Vortex Blue (VB; Dentsply Tulsa Dental Specialties), and iRace (iR; FKG Dentaire) nickel-titanium rotary instruments at body temperature. MATERIALS AND METHODS: Size 30, 0.01 taper of XPS, size 30, 0.04 taper of HCM, VB, iR, and size 30, 0.06 taper of TRS instruments were immersed in saline at 37 ± 1 °C during cyclic fatigue testing. The instruments were tested with 60° angle of curvature and a 3-mm radius of curvature. The number of cycles to failure (NCF) was calculated and the length of the fractured segment was measured. Fractographic examination of the fractured surface was performed using a scanning electron microscope. The data were analyzed statistically using Kruskal-Wallis H test and Mann-Whitney U tests. Statistical significance was set at P < 0.05. RESULTS: XPS had a significantly greater NCF compared with the other instruments (P < 0.001). The topographic appearance of the fracture surfaces of tested instruments revealed ductile fracture of cyclic fatigue failure. CONCLUSION: XPS instruments exhibited greater cyclic fatigue resistance compared with the other tested instruments. CLINICAL RELEVANCE: XP-endo Shaper instruments could be used more safely in curved canals due to their higher fatigue resistance.

A cone-beam computed tomographic analysis of total dentin removed, canal transportation, and canal-centering ability following instrumentation with three different file systems: An in vitro study.

Aims: The aim of this study was to evaluate the shaping ability following instrumentation with XP-endo Shaper (XPS), TruNatomy (TRN), and HyFlex CM (HCM) file system. Subjects and Methods: Fifty-four mesiobuccal canals of mandibular molars were selected and allocated into three groups randomly: XPS, TRN system, and HCM file system. Pre- and postinstrumentation scans were taken using a cone-beam computed tomography scanner to determine the amount of root dentin removed, mesiodistal and buccolingual transportation, and canal-centering ratio at 2, 5, and 8 mm from the root end. Statistical Analysis Used: Data were statistically analyzed using Kruskal-Wallis test and the significance level was set at P = 0.05. Results: TRN file system removed the least amount of root dentin. XPS showed statistically higher M-D canal transportation at 5 mm level from the apex. Conclusions: TRN file system showed better dentin preservation as compared to XPS and HCM. XPS showed the highest canal transportation at 5 mm. All three file systems performed similarly in terms of canal-centering ability.

Comparison of Two Reciprocating and Anatomical Single File Techniques in Cleaning Oval Anatomies.

Introduction: The present study aimed to compare the capability of two single-file shaping systems in disinfecting and cleaning long oval root canals. Materials and Methods: Fifty single-rooted teeth were prepared, contaminated with Enterococcus faecalis and divided into two groups. Two samplings were obtained; S1 before chemo-mechanical preparation and S2 after the preparation. Depending on the group, chemo-mechanical preparation was performed with XP-endo Shaper (XPS) and Wave One Gold (WOG). Five teeth from each group were observed under scanning electron microscopy (1000×) to evaluate the cleanliness of root canals at 3, 6 and 9 mm from the apex. All probability (P-values) were two-tailed, statistical significance was set at 0.05 and analyses were conducted using SPSS statistical software. Results: A significant reduction in the colony forming units was observed from S1 to S2 in both tested groups. In S2, XPS group obtained significantly lower colony forming units (P<0.001). In the cleanliness study, XPS group resulted in significantly cleaner canals compared to WOG. Conclusions: Based on this in vitro study XPS system was more effective in disinfecting and cleaning long oval canals.

Efficiency of ProTaper Universal Retreatment, Reciproc Blue and XP-endo Shaper in the removal of a bioceramic-based root canal filling.

Purpose: This in vitro study aimed to assess the performance of ProTaper Universal Retreatment (PTUR), Reciproc Blue (RB), and XP-endo Shaper (XPS) system in the removal of bioceramic root canal filling. Materials and methods: Forty-five human single-rooted mandibular premolars were prepared up to 30/.04 and filled with Endosequence BC sealer and BC points before being assigned into three groups (n=15). The root canal fillings were removed until reaching predetermined working length (WL) with PTUR in group 1, RB in group 2, and XPS in group 3. During the removal of the filling material, apically extruded debris was collected in pre-weighed Eppendorf tubes, and operation time was recorded with a digital chronometer. Reaching the WL and maintaining apical patency were evaluated separately. The data were statistically analyzed using Kruskal Wallis and Mann Whitney U tests. Results: The mean amount of extruded debris was highest in the PTUR group, although all instruments caused apical extrusion of debris. The mean time for reaching WL was longest for RB and shortest for XPS, with significant differences among the groups (p<0.05). Although the difference was not significant (p=0.799), in the PTUR group the WL was reached in 93.3% of the samples, which was higher than other groups (86.7%). Conclusion: All tested systems caused a certain amount of debris extrusion. XPS was associated with less extrusion while regaining more rapid access to the periapical area than PTUR and RB.

Shaping ability of non-adaptive and adaptive core nickel-titanium single-file systems with supplementary file in ribbon-shaped canals analysed by micro-computed tomography.

This study compared shaping ability between two single-file systems and before/after using supplementary file in untouched area, volume of removed dentin, maximum cut depth (the highest cut depth by main file) and remaining thinnest dentin (the thinnest root dentin after preparation). Ribbon-shaped distal canals of mandibular molars were prepared with non-adaptive core (WaveOne Gold) or adaptive core (XP-endo Shaper) files (n = 15/group) and additionally prepared with a supplementary file (XP-endo Finisher), and the shaping ability was investigated using micro-computed tomography. XP-endo Shaper group demonstrated significantly less overall untouched area than WaveOne Gold group (38.21 ± 6.98% vs. 47.68 ± 9.16%) (p < 0.05). No significant difference was detected between XP-endo Shaper and WaveOne Gold groups in volume of removed dentin (1.85 ± 0.53 vs. 1.66 ± 0.33 mm3 ), maximum cut depth (0.10-0.28 vs. 0.10-0.29 mm) and remaining thinnest dentin (0.66-0.80 vs. 0.78-0.88 mm). Supplementary XP-endo Finisher treatment significantly decreased untouched area (11%-23% reduction) (p < 0.05) with minimally cut root dentin (0.01-0.02 mm).

Shaping ability of different NiTi rotary systems during the preparation of printed mandibular molars.

This study aimed to evaluate the shaping ability of XP-endo Shaper, TruNatomy and EdgeFile X3 during the preparation of resin-printed mandibular molar mesial root canals. Thirty-three resin-based mandibular mesial roots with two canals, obtained from extracted tooth cone-beam computed tomography (CBCT) image and printed on a three-dimensional (3D) printer, were divided into three experimental groups according to the different nickel-titanium (NiTi) systems used for root canal preparation. The specimens were scanned using CBCT imaging before and after root canal preparation. Then images were registered using a dedicated software and changes in the canal area, volume, untouched canal surface and the maximum and minimum dentine wall wear were calculated. The XP-endo Shaper instruments showed improved shaping ability with lower untouched root canal surface and better preservation of root canal anatomy during the preparation of resin-printed mandibular mesial root canals compared with TruNatomy and EdgeFile X3 systems.