Effect of Cast Modification on Denture Base Adaptation Following Maxillary Complete Denture Processing.

PURPOSE: To investigate the effect of cast modifications on denture base adaptation in coronal and sagittal projections following maxillary complete denture processing. MATERIALS AND METHODS: A total of 60 edentulous maxillary casts (n = 10) were distributed among six groups. Group 1 was the control group with no modification, groups 2 through 6 included a butterfly postdam preparation, groups 3 and 4 also included a 10-mm wide/4-mm deep box with addition of four round holes in group 4, and groups 5 and 6 also included a 20-mm wide/4-mm deep box with addition of four round holes in group 6. The boxes were prepared at the mid-heel area of the casts. Two layers of baseplate wax (1 mm each) were used to standardize denture base thickness across the groups. A standard technique was used to replicate the denture tooth set-up, and standardized processing was done for all the groups. Following deflasking, casts with the dentures were sectioned in the coronal and sagittal directions. Microscopic pictures were taken at preselected points. Data were organized in tables, and statistical analyses were performed using repeated measure ANOVA, Tukey post hoc tests, and post hoc comparison tests set at 5% level of significance. RESULTS: Maximum gaps were measured at the mid-palatal area followed by nearby areas and the areas near ridge crests in both coronal and sagittal projections. The analyses revealed significant differences between the groups in coronal projection (1/2, 3/4, 5/6) and sagittal projection (1, 2, 3/4, 5/6) without significant differences within the pairs. The groups were ranked from the highest group 1 to the lowest group 6 relative to the gap means. Post hoc comparisons showed that points 1C and 2A had the highest gap means across the study groups. CONCLUSIONS: Within the limitations of this study, it can be extrapolated that the denture base adaptation can be effectively increased with the box preparation at the mid-heel aspect of the casts. Significant reduction of gaps was seen when the box size increased from 10 to 20 mm in coronal and sagittal projections; however, the addition of four holes had no significant effect on gap size alterations.

Effectiveness of Chemical and Microwave Disinfection on Denture Biofilm Fungi and the Influence of Disinfection on Denture Base Adaptation.

The aims of this study were to evaluate the effectiveness of six disinfection methods and the influence of these methods on the adaptation of maxillary dentures. Acrylic resin specimens contaminated with fungi were exposed to the following disinfection treatments: 1. microwave oven (900 W) at full power for 5 min (with soaking the specimen in 250 ml water), 2. microwave oven at medium power for 5 min (with soaking the specimen in 250 ml water), 3. sodium hypochlorite 5.25 % for 5 min, 4. diluted sodium hypochlorite 1:420 for 5 h, 5. Chlorhexidine gluconate for 5 h, 6. effervescent tablets for 15 min, 7. soaking in 250 ml tap water for 15 min. Colony forming units (CFUs) of remaining cells were counted and compared with t test (p ≤ 0.05). Dimensional stability was evaluated using aluminum die simulating the maxillary edentulous arch. Posterior palatal gaps were measured. Data were analyzed using one-way ANOVA test and t test (p ≤ 0.05). Microwave irradiation (at full or medium power) and sodium hypochlorite 5.25 % for 5 min were able to reduce the CFUs of fungi by more than 4 log10 whereas diluted sodium hypochlorite, chlorhexidine gluconate, and effervescent tablets did not achieve a reduction of >2.8, 2.68 and 1.66, respectively. For dimensional stability test, t test revealed significant difference between control group and the microwave at full power group (p = 0.000). Within the limits of this study, microwave oven at medium power and sodium hypochlorite (5.25 %) are effective and safe methods of disinfecting removable dentures.

Evaluation of the potential denture covering area in buccal shelf with intraoral scanner.

Background/purpose: The characteristic of soft tissue changes in buccal shelf area during function is unclear. This study aimed for evaluating the potential denture covering area in buccal shelf area in different ranges of mouth opening by a digital approach. Materials and methods: Nineteen qualified dentate participants were enrolled. An intraoral scanner was used to record soft tissue in buccal shelf area in different ranges of mandibular opening, which were maximum intercuspation, 10 mm, 20 mm, and 30 mm of interincisal distance. The experiment was performed by two examiners. The common area of each range was generated within the clinically acceptable denture adaptation range, which was represented as the potential denture covering area. Data were statistically analyzed using descriptive statistic, one-way repeated measure ANOVA, intraclass correlation coefficient (ICC), and the Pearson correlation test. Results: Trends of the mean distance of the potential denture covering area increased from the frenum area to the second premolar and the first molar area then decreased in the second molar area, along with the ranges of mouth opening increased. The distance in the second molar area had drastic percentage changes during the mouth opening. The mean distances changed significantly when the mouth opening increased (P < 0.001). All ICC values of intra-, inter-rater reliability indicated good to excellent reliability. The correlation between the results from two examiners was strong (P < 0.001). Conclusion: The characteristic of the denture covering area posteriorly to the first molar area is inversely proportional in length to ranges of mouth opening.

Comparison of cooling methods on denture base adaptation of rapid heat-cured acrylic using a three-dimensional superimposition technique.

Aim: To investigate the effect of different cooling methods on denture base adaptation of rapid heat-cured acrylic resin using 3D superimposition technique. Setting and Design: In vitro - Comparative study. Materials and Methods: Denture base adaptation of two different rapid heat-cured polymethyl methacrylate acrylic resins using five different cooling methods were compared. Forty maxillary edentulous stone cast were prepared to produce the denture bases with standardized thickness. The specimens were divided into five groups (n = 8) according to type of materials and cooling methods. The master stone cast and all forty denture bases were scanned with 3Shape E1 laboratory scanner. The scanned images of each of the denture bases were superimposed over the scanned image of the master cast using Materialize 3-matic software. Three dimensional differences between the two surfaces were calculated and color surface maps were generated for visual qualitative assessment. Statistical Analysis Used: Generalized Linear Model Test, Bonferroni Post Hoc Analysis. Results: All bench-cooled specimens showed wide green-colored area in the overall palatal surface, while the rapid cooled specimens presented with increased red color areas especially at the palate and post dam area. Generalized Linear Model test followed by Bonferroni post hoc analysis showed significant difference in the root mean square values among the specimen groups. Conclusion: Samples that were bench cooled, demonstrated better overall accuracy compared to the rapid cooling groups. Regardless of need for shorter denture processing time, bench cooling of rapid heat-cured PMMA is essential for acceptable denture base adaptation.