Preparation of Quaternary Ammonium Separation Material based on Coupling Agent Chloromethyl Trimethoxysilane (KH-150) and Its Adsorption and Separation Properties in Studies of Th(IV).

In this research, the authors studied the synthesis of a silicon-based quaternary ammonium material based on the coupling agent chloromethyl trimethoxysilane (KH-150) as well as its adsorption and separation properties for Th(IV). Using FTIR and NMR methods, the silicon-based materials before and after grafting were characterized to determine the spatial structure of functional groups in the silicon-based quaternary ammonium material SG-CTSQ. Based on this, the functional group grafting amount (0.537 mmol·g-1) and quaternization rate (83.6%) of the material were accurately calculated using TGA weight loss and XPS. In the adsorption experiment, the four materials with different grafting amounts showed different degrees of variation in their adsorption of Th(IV) with changes in HNO3 concentration and NO3- concentration but all exhibited a tendency toward anion exchange. The thermodynamic and kinetic experimental results demonstrated that materials with low grafting amounts (SG-CTSQ1 and SG-CTSQ2) tended to physical adsorption of Th(IV), while the other two tended toward chemical adsorption. The adsorption mechanism experiment further proved that the functional groups achieve the adsorption of Th(IV) through an anion-exchange reaction. Chromatographic column separation experiments showed that SG-CTSQ has a good performance in U-Th separation, with a decontamination factor for uranium in Th(IV) of up to 385.1, and a uranium removal rate that can reach 99.75%.

Synthesis of Silane Functionalized LDH-Modified Nanopowders to Improve Compatibility and Enhance Corrosion Protection for Epoxy Coatings.

Novel modified Zn-Al LDH/epoxy coatings are synthesized and applied to steel substrates, providing active corrosion protection and improved barrier properties. This protective coating is made by combining Epon 828 as a polymer matrix with modified layered-double-hydroxy (LDH) nanoparticles acting as corrosion inhibitor containers. To synthesize the coatings, nitrate was intercalated into Zn-Al-LDH layers through an aqueous co-precipitation method to obtain Zn-Al LDH-NO3, and decavanadate replaced nitrate within the LDH layers through an anion exchange process to obtain Zn-Al LDH-(V10O28)6-. The intercalated LDH was functionalized by silanization with (3-aminopropyl)triethoxysilane (APTES) to increase the compatibility of the LDH inhibitor nanocontainers with epoxy resin and produce a protective coating. To protect the mild steel substrate, functionalized LDH nanopowders were dispersed into the epoxy resin, mixed with a polyamide hardener (Epikure 3571), and applied and cured to the metal surface. Surface morphology, structure, and chemical composition were determined for the modified LDH nanopowders using scanning electron microscopy, energy-dispersive X-ray analysis, X-ray diffraction, infrared spectroscopy, X-ray photoelectron spectroscopy, and thermogravimetric analysis. Corrosion protection of the coating system was studied using long-term immersion testing and potentiodynamic polarization studies in a 3.5 wt.% NaCl solution.

Functional Nanocomposites in the Development of Flexible Armor.

The idea of flexible body armor has been around for many years. Initial development included shear thickening fluid (STF) as a backbone polymer to impregnate ballistic fibers such as Kevlar. At the core of the ballistic and spike resistance was the instantaneous rise in viscosity of STF during impact. Increase in viscosity was due to the hydroclustering of silica nanoparticles dispersed in polyethylene glycol (PEG) through a centrifuge and evaporation process. When STF composite was dry, hydroclustering was not possible due to absence of any fluidity in PEG. However, particles embedded within the polymer, covered the Kevlar fiber and offered some resistance to spike and ballistic penetration. The resistance was meagre and hence, the goal was to improve it further. This was achieved by creating chemical bonds between particles, and by strongly attaching particles to the fiber. PEG was replaced with silane (3-amino propyl trimethoxysilane), and a fixative cross-linker, Glutaraldehyde (Gluta), was added. Silane installed an amine functional group on the silica nanoparticle surface, and Gluta created strong bridges between distant pairs of amine groups. Amide functional groups present in Kevlar also interacted with Gluta and silane to form a secondary amine, allowing silica particles to attach to fiber. A network of amine bonding was also established across the particle-polymer-fiber system. In synthesizing the armor, silica nanoparticles were dispersed in a mixture of silane, ethanol, water, and Gluta, maintaining an appropriate ratio by weight, and using a sonication technique. Ethanol was used as a dispersion fluid and was evaporated later. Several layers of Kevlar fabric were then soaked with the admixture for about 24 h and dried in an oven. Armor composites were tested in a drop tower according to NIJ115 Standard using spikes. Kinetic energy at impact was calculated and normalized with the aerial density of the armor. NIJ tests revealed that normalized energy for 0-layer penetration increased from 10 J-cm2/g (STF composite) to 220 J-cm2/g for the new armor composite, indicating a 22-fold enhancement. SEM and FTIR studies confirmed that this high resistance to spike penetration was due to the formation of stronger C-N, C-H, and C=C-H stretches facilitated by the presence of silane and Gluta.

Bonding stability of universal adhesives to feldspathic ceramic with or without prior silane application.

PURPOSE: This study aimed to assess the bonding stability of three universal adhesives to a CAD-CAM feldspathic ceramic with or without prior silane application. MATERIALS AND METHODS: The universal adhesives tested were Ambar Universal (FGM), Single Bond Universal (3M), and Ybond Universal (Yller). Scotchbond Multipurpose Plus (3M) was used as a control. The silane used was RelyX Ceramic Primer (3M). Microtensile bond strength (µTBS) to Vitablocs Mark II was measured after 24 h or 6 months of water aging (n = 20). Failure modes were observed through scanning electron microscopy, and pH and degree of C=C conversion (DC) of the adhesives were measured (n = 3). Data were analyzed using one-, two-, and three-way ANOVA. RESULTS: The pH values differed significantly among the adhesives (p < 0.001), while the DC was similar (p = 0.141). The universal adhesives showed significant differences in µTBS, with higher immediate results when using silane and lower results after aging. Notably, a significant decrease in µTBS was observed after 6 months when silane was applied. In contrast, the control adhesive exhibited consistent results between the 24-h and 6-month storage periods. The universal adhesives showed a decrease in µTBS ranging from 25.5% to 40.1% after prolonged storage. Adhesive failures were predominant in all groups. The presence or absence of silane in the adhesive composition did not affect the bonding performance. CONCLUSIONS: The application of a separate silane coupling agent improved the immediate bond strength of universal adhesives to CAD-CAM feldspathic ceramic. However, this bond strength significantly decreased after 6 months of water aging. The bond strength remained stable for universal adhesives when applied without silane after 6 months of aging.

Effects of Wood Flour (WF) Pretreatment and the Addition of a Toughening Agent on the Properties of FDM 3D-Printed WF/Poly(lactic acid) Biocomposites.

In order to improve the properties of wood flour (WF)/poly(lactic acid) (PLA) 3D-printed composites, WF was treated with a silane coupling agent (KH550) and acetic anhydride (Ac2O), respectively. The effects of WF modification and the addition of acrylicester resin (ACR) as a toughening agent on the flowability of WF/PLA composite filament and the mechanical, thermal, dynamic mechanical thermal and water absorption properties of fused deposition modeling (FDM) 3D-printed WF/PLA specimens were investigated. The results indicated that the melt index (MI) of the specimens decreased after WF pretreatment or the addition of ACR, while the die swell ratio increased; KH550-modified WF/PLA had greater tensile strength, tensile modulus and impact strength, while Ac2O-modified WF/PLA had greater tensile modulus, flexural strength, flexural modulus and impact strength than unmodified WF/PLA; after the addition of ACR, all the strengths and moduli of WF/PLA could be improved; after WF pretreatment or the addition of ACR, the thermal decomposition temperature, storage modulus and glass transition temperature of WF/PLA were all increased, and water absorption was reduced.

The Bond Strength of a Universal Adhesive System with Silane to Lithium Disilicates in Comparison with an Isolated Silane Coupling Agent.

PURPOSE: The aim of this in vitro study was to evaluate the effects of different durations of silane coupling agent application compared to a universal adhesive system regarding the shear bond strength of two ceramic materials. MATERIALS AND METHODS: A total of 120 human molars were ground to the dentinal coronal third and then fixed into an acrylic resin holder. Lithium disilicate specimens were divided into two main groups according to the ceramic type: computer-aided design/computer-aided manufacturing IPS e.max CAD and heat-pressed Initial LiSi Press GC (dimensions of 4 × 3× 3 mm). Each main group was subdivided into 6 subgroups (n = 10) according to the duration of the silane and universal adhesive system application (20, 60, or 120 seconds) on the ceramic surface before cementation; then, the cementation procedures were performed. All specimens were subjected to 5000 thermal cycles at 5 and 55°C before testing. The shear bond strength was measured using a universal testing machine. ANOVA and Scheffe post hoc test multiple comparisons tests were conducted (α = 0.05). RESULTS: The shear bond strength increased as the duration of the silane and universal adhesive system application increased. The highest bond value for each material was found for the silane application at 120 seconds, with a significant difference between 120 and 60, and 20 seconds for both e. max CAD and Initial LiSi materials (p = 0.029 and p ˂ 0.001, respectively). No significant difference was found between 60 and 20 seconds when silane and universal adhesive system were applied for both e. max CAD and Initial LiSi materials (p = 0.169 and p = 0.120, respectively). All groups treated with the silane primer showed significantly higher values than the universal adhesive system for each application time (p ˂ 0.001). CONCLUSION: Increasing the duration of the silane coupling agent and universal adhesive system application to 120 seconds on the ceramic surface before cementation improved the shear bond strength of the ceramic-cement interface. Ceramic pretreatment with silane could be an essential step for bonding ceramic to dentin regardless of silane presence in the universal adhesive system.

Strategies for Preparation of Chiral Stationary Phases: Progress on Coating and Immobilization Methods.

Enantioselective chromatography is one of the most used techniques for the separation and purification of enantiomers. The most important issue for a specific successful enantioseparation is the selection of the suitable chiral stationary phase (CSP). Different synthetic approaches have been applied for the preparation of CSPs, which embrace coating and immobilization methods. In addition to the classical and broadly applied coating and immobilization procedures, innovating strategies have been introduced recently. In this review, an overview of different methods for the preparation of coated and immobilized CSPs is described. Updated examples of CSPs associated with the various strategies are presented. Considering that after the preparation of a CSP its characterization is fundamental, the methods used for the characterization of all the described CSPs are emphasized.

Silane Coupling Agent Modifies the Mechanical Properties of a Chitosan Microfiber.

Chitosan microfibers are widely used in medical applications because they have favorable inherent properties. However, their mechanical properties require further improvement. In the present study, a trimethoxysilane aldehyde (TMSA) crosslinking agent was added to chitosan microfibers to improve their tensile strength. The chitosan microfibers were prepared using a coagulation method. The tensile strength of the chitosan microfibers was improved by crosslinking them with TMSA, even when only a small amount was used (less than 1%). TMSA did not change the orientation of the chitosan molecules. Furthermore, aldehyde derived from TMSA did not remain, and siloxane units were formed in the microfibers.

Antibacterial application of covalently immobilized photosensitizers on a surface.

Singlet oxygen produced by irradiating photosensitizers (PSs) can be used to kill pathogens during water treatment. Chemical immobilization of the PSs on surfaces can maintain their disinfection function long-term. In this study, two model PSs (rose bengal (RB) and hematoporphyrin (HP)) were immobilized on a glass surface using a silane coupling agent with an epoxide group, and their antibacterial properties were analyzed. Fourier transform infrared spectroscopy demonstrated that a covalent bond formed between the epoxide group and hydroxyl group in the PSs. A large proportion of the immobilized PSs (approximately 50%) was active in singlet oxygen production, which was evidenced by a comparative analysis with free PSs. RB was more effective at producing singlet oxygen than HP. The immobilized PSs were durable in terms of repeated use. On the other hand, singlet oxygen produced by the PSs was effective at killing bacteria, mostly for Gram-positive bacteria (> 90% death for 2 h of irradiation), by damaging the cell membrane. The preferable antibacterial property against Gram-positive bacteria compared with that against Gram-negative bacteria suggested efficient penetrability of singlet oxygen across the cell membrane, which led to cell death. Taken together, it was concluded that immobilization of PSs on surfaces using the silane coupling agent proposed in this study was effective at killing Gram-positive bacteria by forming singlet oxygen.

Study on the Mechanical Properties and Strengthening Mechanism of Interface-Modified Carbon Fiber Mesh Reinforced Cement-Based Composites with SCA&HMC.

Carbon fiber mesh reinforced cement-based composites (CMCCs) have received extensive attention in the field of engineering repair and structural reinforcement due to their outstanding properties such as two-way force, rust prevention, high specific strength, and low base surface requirements. However, the development of this material has been slowed down to some extent due to the poor interfacial bonding between the carbon fiber mesh and the cement matrix. In this paper, a novel fabrication strategy was proposed in which the carbon fiber mesh was modified with epoxy resin and silane coupling agent (SCA) to increase its surface chemical activity. Meanwhile, the hydroxymethyl cellulose (HMC) was also filled into the concrete matrix to improve the mechanical strength of the matrix as well as the load transfer behaviors between the mortar and carbon fiber (CF) mesh. The potential to employ SCA and HMC was evaluated for the making of CMCCs via the above methods. The results showed that the longitudinal shear strength of composites with SCA and SCA&HMC increased by 26.6% and 56.1% compared to those of CF with epoxy resin (EP) reinforced composites, respectively. The flexural strength of composite with SCA&HMC increases by 147.6% compared to I-(F) without CF. The novel II-HCM&CF/EP-SCA composites with excellent performance are promised to be applied in practical uses.

Immobilization of carbonic anhydrase on polyvinylidene fluoride membranes.

In recent years, the application of carbonic anhydrase (CA) in CO2 removal has attracted great interest. However, obtaining high enzyme recovery activity is difficult in existing immobilization techniques. In this work, water plasma-treated poly(vinylidene fluoride) (PVDF) membranes were modified via 3-aminopropyl triethoxy silane (KH550) or γ-(2, 3-epoxypropoxy) propyl trimethoxy silane (KH560), and then CA was attached. The immobilization process was optimized, and the catalytic properties of PVDF-attached CA were characterized. The maximum activity recovery of PVDF-KH550-CA was 60%, whereas that of PVDF-KH560-CA was 33%. The Km values of PVDF-KH550-CA, PVDF-KH560-CA, and free enzyme were 9.97 ± 0.37, 12.5 ± 0.2, and 6.18 ± 0.23 mM, respectively, and their Kcat /Km values were 206 ± 2, 117 ± 5, and 488 ± 4 M-1 ·Sec-1 . PVDF-attached CA shows excellent storage stability and reusability, and their half-life values were 82 and 78 days at 4 °C. At 25 °C, they were 50 and 37 days, respectively. PVDF-KH550-CA and PVDF-KH560-CA retained approximately 85% and 72% of the initial activity after undergoing 10 cycles. In the presence of them, the generation rates of CaCO3 were 76% and 65% of the free CA system, which were 1.6 and 1.3 times that of the blank system, respectively. Its role in accelerating CO2 sequestration holds great promise for its practical application.

Effect of silane pretreatment on the immediate bonding of universal adhesives to computer-aided design/computer-aided manufacturing lithium disilicate glass ceramics.

The aim of this study was to investigate the effect of silane pretreatment on the universal adhesive bonding between lithium disilicate glass ceramic and composite resin. IPS e.max ceramic blocks etched with hydrofluoric acid were randomly assigned to one of eight groups treated with one of four universal adhesives (two silane-free adhesives and two silane-containing adhesives), each with or without silane pretreatment. Bonded specimens were stored in water for 24 h. The shear bond strength (SBS) of the ceramic-resin interface was measured to evaluate bond strength, and the debonded interface after the SBS test was analysed using field-emission scanning electron microscopy to determine failure mode. Light microscopy was performed to analyse microleakage and marginal sealing ability. Silane pretreatment significantly and positively influenced SBS and marginal sealing ability. For all the universal adhesive groups, SBS increased and the percentage of microleakage decreased after the pretreatment. Without the pretreatment, SBS and the percentage of microleakage were not significantly different between the silane-containing universal adhesive groups and the silane-free groups. Cohesive failure was the main fracture pattern. The results suggest that additional silane pretreatment can effectively improve the bonding strength and marginal sealing of adhesives to lithium disilicate glass ceramics. The bonding performance of silane-containing universal adhesives without pretreatment is similar to that of silane-free adhesives.

Silane Modified Diopside for Improved Interfacial Adhesion and Bioactivity of Composite Scaffolds.

Diopside (DIOP) was introduced into polyetheretherketone/polyglycolicacid (PEEK/PGA) scaffolds fabricated via selective laser sintering to improve bioactivity. The DIOP surface was then modified using a silane coupling agent, 3-glycidoxypropyltrimethoxysilane (KH570), to reinforce interfacial adhesion. The results showed that the tensile properties and thermal stability of the scaffolds were significantly enhanced. It could be explained that, on the one hand, the hydrophilic group of KH570 formed an organic covalent bond with the hydroxy group on DIOP surface. On the other hand, there existed relatively high compatibility between its hydrophobic group and the biopolymer matrix. Thus, the ameliorated interface interaction led to a homogeneous state of DIOP dispersion in the matrix. More importantly, an in vitro bioactivity study demonstrated that the scaffolds with KH570-modified DIOP (KDIOP) exhibited the capability of forming a layer of apatite. In addition, cell culture experiments revealed that they had good biocompatibility compared to the scaffolds without KDIOP. It indicated that the scaffolds with KDIOP possess potential application in tissue engineering.

Synthesis of N-(2-diethylamino-ethyl)-4-(4-fluoro-benzamido)-2-methoxybenzamide (desiodo-MIP-1145) by coupling technique and its radioiodination: a potential melanoma imaging agent.

Radioiodinated MIP-1145, which specifically targets melanin, is an ideal candidate for targeted therapy of melanoma. An analogue of MIP-1145 lacking the iodo-substituent (desiodo-MIP-1145) was synthesized as a labeling precursor in three simple steps. The radioiodination of desiodo-MIP-1145 by iodine-125 was carried out via an electrophilic substitution reaction. An optimization study for the iodination reaction was carried out. The labeled compound was isolated and purified by means of electrophoresis and HPLC. The maximum radiochemical yield, 76%, was obtained with radiochemical purity greater than 99%. The log P value for [(125) I]MIP-1145 was measured as 4.5.

Treatment of high-latency microcapsules containing an aluminium complex with an epoxy-functionalised trialkoxysilane.

Some aluminium complexes are excellent catalysts of cationic polymerisation and are used for low-temperature and fast-curing adhesive, used in electronic part mounting. Microencapsulation is a suitable technique for getting high latency of the catalysts and long shelf life of the adhesives. For the higher latency in a cycloaliphatic epoxy compound, the microcapsule surface which retained small amount of aluminium complex was coated with epoxy polymer and the effect was examined. From the X-ray photoelectron spectroscopic results, the surface was recognised to be sufficiently coated and the differential scanning calorimetric analyses showed that the coating did not significantly affect the low-temperature and fast-curing properties of adhesive. After storing the mixture of cycloaliphatic epoxy compound, coated microcapsules, triphenylsilanol and silane coupling agent for 48 h at room temperature, the increase in viscosity was only 0.01 Pa s, resulting in the excellent shelf life.

Design of Phosphonated Imidazolium-Based Ionic Liquids Grafted on γ-Alumina: Potential Model for Hybrid Membranes.

Imidazolium bromide-based ionic liquids bearing phosphonyl groups on the cationic part were synthesized and grafted on γ-alumina (γ-Al2O3) powders. These powders were prepared as companion samples of conventional mesoporous γ-alumina membranes, in order to favor a possible transfer of the results to supported membrane materials, which could be used for CO2 separation applications. Effective grafting was demonstrated using energy dispersive X-ray spectrometry (EDX), N2 adsorption measurements, fourier transform infrared spectroscopy (FTIR), and special attention was paid to (31)P and (13)C solid state nuclear magnetic resonance spectroscopy (NMR).

Evaluation of flexural strength of resin interim restorations impregnated with various types of silane treated and untreated glass fibres.

BACKGROUND: Flexural strength is an important mechanical property that determines the long-term prognosis of interim restorations. Studies are lacking regarding the effect of silanation of the various types of glass fibre impregnation on the flexural strength of resin interim restorations. METHODS: A customized metal die was milled to simulate the prepared abutments of a three-unit fixed dental prosthesis. A total of seventy five samples of interim fixed dental prostheses were prepared using autopolymerizing tooth colour acrylic resin. Unidirectional and woven forms of glass fibres (Stick and Stick Net), which were silane treated and untreated were used to reinforce the resin matrix. Fifteen samples were prepared for each group along with unreinforced group serving as control. The flexural strength was evaluated with universal testing machine. RESULTS: The means and standard deviations of flexural strength for different groups were 13.90 ± 2.96 (control), 61.58 ± 5.26 (unidirectional fibres), 30.89 ± 3.60 (woven fibres), 112.05 ± 5.51 (silane treated unidirectional fibres) and 73.85 ± 4.10 (silane treated woven fibres) respectively. The mean flexural strength of silane treated unidirectional fibres (112.05 MPa) was highest and statistically highly significant (P < 0.0001) compared to all other groups. CONCLUSIONS: Within the limitations of the current study, flexural strength of the reinforced PMMA interim fixed dental prosthesis was significantly higher (P < 0.0001) when compared to the unreinforced PMMA interim fixed dental prosthesis. The use of silane treated unidirectional glass fibres is an effective method of reinforcing interim fixed restorations made of PMMA resins.

Effects of surface treatments and cement types on the bond strength of porcelain-to-porcelain repair.

PURPOSE: The purpose of this in vitro study was to evaluate the effects of four surface treatments and two resin cements on the repair bond strength of a ceramic primer. MATERIALS AND METHODS: Eighty-eight pairs of disks (10 and 5 mm in diameter, 3 mm thickness) were prepared from heat-pressed feldspar ceramics (GC Initial IQ). After being stored in mucin-artificial saliva for 2 weeks, the 10-mm disks were divided into four surface treatment groups (n = 22) and then treated as follows: (1) no treatment (control); (2) 40% phosphoric acid; (3) 5% hydrofluoric acid + acid neutralizer + 40% phosphoric acid; (4) silica coating (CoJet-sand) + 40% phosphoric acid. The 5-mm disks were treated with 5% hydrofluoric acid + 40% phosphoric acid. The two sizes of porcelain disks, excluding the control group, were primed with Clearfil Ceramic Primer. The specimens in each group were further divided into two subgroups of 11 each, and bonded with Clearfil Esthetic Cement (CEC) or Panavia F 2.0 Cement (PFC). The specimens were stored in distilled water at 37°C for 24 hours, thermocycled for 3000 cycles at 5 to 55°C, and stored at 37°C for an additional 7 days. Shear bond strength (SBS) was measured with a universal testing machine at a 0.5 mm/min crosshead speed until fracture. Statistical analysis of the results was carried out with a two-way ANOVA and Tukey HSD test (α = 0.05). Debonded specimen surfaces were examined under an optical microscope to determine the mode of failure. RESULTS: The statistical analysis showed that the SBS was significantly affected by surface treatment and resin cement (p < 0.05). For treatment groups bonded with CEC, the SBS (MPa) values were (1) 2.64 ± 1.1, (2) 13.31 ± 3.6, (3) 18.88 ± 2.6, (4) 14.27 ± 2.7, while for treatment groups cemented with PFC, the SBS (MPa) values were (1) 3.04 ± 1.1, (2) 16.44 ± 3.3, (3) 20.52 ± 2.2, and (4) 16.24 ± 2.9. All control specimens exhibited adhesive failures, while mixed types of failures were observed in phosphoric acid-treated groups. The other groups revealed mainly cohesive and mixed failures. CONCLUSIONS: Combined surface treatment of etching with hydrofluoric acid and phosphoric acid provides the highest bond strengths to porcelain. Also, PFC exhibited higher SBS than CEC did.

Adhesion Strength Enhancement of Butyl Rubber and Aluminum Using Nanoscale Self-Assembled Monolayers of Various Silane Coupling Agents for Vibration Damping Plates.

In this paper, we enhance the adhesion strength of butyl rubber-based vibrational damping plates using nanoscale self-assembled monolayers of various silane coupling agents. The silane coupling agents used to chemically modify the plate's aluminum surface include 3-aminopropyltriethoxysilane (APTES), (3-glycidyloxypropyl) triethoxysilane (GPTES), 3-mercaptopropyltrimethoxysilane (MPTMS), and 3-(triethoxysilyl)propyl isocyanate (ICPTES). The modified surfaces were analyzed using Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), and the enhancement in adhesion strength between the rubber and aluminum was estimated through T-Peel tests. As a result, MPTMS showed the highest enhancement in adhesion strength, of approximately 220% compared to the untreated sample, while GPTES, ICPTES, and APTES resulted in adhesion strength enhancements of approximately 200%, 150%, and 130%, respectively.

Influence of Silane Coupling Agent and Anionic Dispersant on the Dispersion Effect of Silicon Carbide Particles.

Silicon carbide (SiC), as a widely used material, has great properties. To improve the flowability of ultrafine silicon carbide slurry, this study used sodium humate, tetramethylammonium hydroxide (TMAH), and N-(ß-monoaminoethyl)-γ-aminopropyltrimethyl(ethoxysilane) (KH792) to modify the ultrafine silicon carbide powder produced by Qingzhou Micro Powder Company. The effects of different modifiers on improving the flowability of ultrafine silicon carbide slurry were investigated by means of viscosity tests, sedimentation experiments, and SEM observations. Their modification mechanisms were investigated by means of zeta potential tests, XPS tests, and so on. In this paper, the initial modification of SiC was carried out with KH792, followed by the secondary modification with anionic and cationic modifiers (tetramethylammonium hydroxide and sodium humate), and the optimal modification conditions were investigated by means of a viscosity test, which showed that the lowest viscosity of the modified SiC reached 0.076 Pa·s and that the absolute maximum value of the zeta potential increased from 47.5 at the time of no modification to 63.7 (maximum values) at the time of modification. This means it has an improved surface charge, which improves dispersion. The adsorption results of the modifier on the silicon carbide surface were also demonstrated by the XPS test results.