Zirconia toughened fluorosilicate glass-ceramics for dental prosthetic restorations.

Background: Dental glass-ceramics have limited strength and are unsuitable for high-stress-bearing areas. Zirconia stands out as a popular choice for reinforcing dental glass-ceramics due to its biocompatibility and high fracture toughness. Objectives: The objective of the study is to investigate the effect of an increase in zirconia (25, 30, 35 and 50 wt%) on microstructure, chemical solubility, hardness, fracture toughness, and brittleness index of fluorosilicate glass systems for dental restorative applications. Material and methods: The fluorosilicate glass frit was obtained through the melt-quench technique. The glass frit was ball-milled with 25, 30, 35 and 50 wt % of 3 mol% yttria-stabilized zirconia (G-25Z, G-30Z, G-35Z, and G-50Z). The composites were sintered to 1000 °C for 48h at a heating rate of 5 °C/min. The glass frit was subject to differential scanning calorimetry. Phase analysis and microstructural characterization were carried out. The crystallite size of zirconia and glass-ceramics, micro-hardness, indentation fracture toughness, brittleness index, and chemical solubility were evaluated. Results: Phase analysis reveals tetragonal and monoclinic zirconia with minor peaks of forsterite, fluorphlogopite, norbergite, and spinel. Their microstructures reveal the characteristic house-of-cards arrangement of fluorophlogopite crystals with dispersed zirconia. The results of hardness and fracture toughness show a statistically significant improvement with an increase in zirconia content. The crystallite size of zirconia and fluorophlogopite crystals with aspect ratio, brittleness index, and chemical solubility declined as the zirconia content increased. Conclusions: Increase in zirconia content from 25 wt % to 50 wt % in heat-treated fluorosilicate glass systems reveals non-reactive zirconia with a stable glass matrix and limits the growth of fluorphlogopite crystals with a house-of-cards microstructure. This results in a range of properties suitable for dental restorations of enhanced hardness, and improved fracture toughness. Despite these improvements, the material maintains its machinability with reduced chemical solubility.

Delayed vs. immediate placement of restorative materials over Biodentine and RetroMTA: a micro-shear bond strength study.

BACKGROUND: The aim of the present study was to investigate the micro-shear bond strength (µSBS) of various restorative materials applied on two different fast-setting calcium silicate-based materials and to evaluate the effect of restoration time on µSBS. METHODS: A total of 180 acrylic blocks with a cavity in the center were randomly divided into 2 main groups according to the capping material to be used (Biodentine or RetroMTA). The specimens were also randomly divided into 3 groups according to the restoration time (3 min, 12 min, 24 h). After the specified waiting periods, glass hybrid material (EQUIA Forte HT), resin composite (Filtek Z550) and light-cured calcium silicate material (Theracal LC) were placed on the specimens with tygon tubes. The specimens were kept for 24 h and then subjected to µSBS test. Statistical analysis was performed by 3-way ANOVA followed by Tukey test for pairwise comparisons (α = 0.05). RESULTS: There is a statistically significant difference (p < 0.05) between the µSBS values obtained by applying resin composite on RetroMTA after different setting times (24 h > 12 min > 3 min). The µSBS obtained for the Biodentine-resin composite at the end of the 3 min setting time is significantly lower (p < 0.05) than the µSBS values at 12 min and 24 h. For both calcium silicate cements, at the end of all time periods, the µSBS obtained when resin composite was applied at the end was higher than the other materials (p < 0.05). CONCLUSIONS: For Biodentine-resin composite bonding, the manufacturer's recommendation of 12 min can be considered an appropriate time, whereas for RetroMTA-resin composite bonding, the µSBS increased as the waiting time increased. Regardless of the waiting time, it is recommended to prefer direct composite resin restoration over Biodentine and RetroMTA.

The flexural strength of 3D-printed provisional restorations fabricated with different resins: a systematic review and meta-analysis.

BACKGROUND: Three-dimensional (3D) printing technology has revolutionized dentistry, particularly in fabricating provisional restorations. This systematic review and meta-analysis aimed to thoroughly evaluate the flexural strength of provisional restorations produced using 3D printing while considering the impact of different resin materials. METHODS: A systematic search was conducted across major databases (ScienceDirect, PubMed, Web of Sciences, Google Scholar, and Scopus) to identify relevant studies published to date. The inclusion criteria included studies evaluating the flexural strength of 3D-printed provisional restorations using different resins. Data extraction and quality assessment were performed using the CONSORT scale, and a meta-analysis was conducted using RevMan 5.4 to pool results. RESULTS: Of the 1914 initially identified research articles, only 13, published between January 2016 and November 2023, were included after screening. Notably, Digital Light Processing (DLP) has emerged as the predominant 3D printing technique, while stereolithography (SLA), Fused Deposition Modeling (FDM), and mono-liquid crystal displays (LCD) have also been recognized. Various printed resins have been utilized in different techniques, including acrylic, composite resins, and methacrylate oligomer-based materials. Regarding flexural strength, polymerization played a pivotal role for resins used in 3D or conventional/milled resins, revealing significant variations in the study. For instance, SLA-3D and DLP Acrylate photopolymers displayed distinct strengths, along with DLP bisacrylic, milled PMMA, and conventional PMMA. The subsequent meta-analysis indicated a significant difference in flexure strength, with a pooled Mean Difference (MD) of - 1.25 (95% CI - 16.98 - 14.47; P < 0.00001) and a high I2 value of 99%, highlighting substantial heterogeneity among the studies. CONCLUSIONS: This study provides a comprehensive overview of the flexural strength of 3D-printed provisional restorations fabricated using different resins. However, further research is recommended to explore additional factors influencing flexural strength and refine the recommendations for enhancing the performance of 3D-printed provisional restorations in clinical applications.

Degradation products of resin-based materials detected in saliva in vivo.

OBJECTIVES: Dental composites remain under scrutiny regarding their (long-term) safety. In spite of numerous studies on the release of monomers both in vitro and in vivo, only limited quantitative data exist on the in vivo leaching of degradation products from monomers and additives. The aim of this observational study was for the first time to quantitatively and qualitatively monitor the release of parent compounds and their degradation products in saliva from patients undergoing multiple restorations. MATERIALS AND METHODS: Five patients in need of multiple large composite restorations (minimally 5 up to 28 restorations) due to wear (attrition, abrasion, and erosion) were included in the study, and they received adhesive restorative treatment according to the standard procedures in the university clinic for Restorative Dentistry. Saliva was collected at different time points, starting before the restoration up until 24 h after the treatment with composite restorations. Saliva extracts were analyzed by liquid chromatography-mass spectrometry. RESULTS: Leaching of monomers and degradation products was highest within 30 min after the placement of the restorations. The highest median concentrations of monomers were recorded for UDMA, BisEMA-3, and TEGDMA; yet, besides BisEMA-3 and TEGDMA, no monomers could be detected after 24 h. Mono- and demethacrylated degradation products remained present up to 24 h and concentrations were generally higher than those of monomers. In patients with multiple restorations, degradation products were still present in the sample taken before the next operation, several weeks after the previous operation. CONCLUSIONS: Exposure to residual monomers and degradation products occurs in the first hours after restoration. Monomers are present in saliva shortly after restoration, but degradation products can be detected weeks after the restoration confirming a long-term release. CLINICAL SIGNIFICANCE: Future research should focus more on the release of degradation products from monomers and additives from resin-based materials given their prolonged presence in saliva after restoration.

Fracture resistance and failure mode of endodontically treated premolars reconstructed by different preparation approaches: Cervical margin relocation and crown lengthening with complete and partial ferrule with three different post and core systems.

PURPOSE: To assess the fracture resistance and failure mode of endodontically treated premolars reconstructed by different preparation approaches: cervical margin relocation (CMR) and crown lengthening (CL) with complete ferrule (CLF) and partial ferrule (CLPF) with three different post and core systems. MATERIALS AND METHODS: In this in vitro study, 100 maxillary premolars were assigned to the following 10 groups according to their preparation approach and type of post and core system (n = 10): (I) control (intact teeth), (II) prefabricated fiber post (PFP) and composite core with CMR (PFP-CMR), (III) polyethylene fiber-reinforced composite (PEFRC) with CMR (PEFRC-CMR), (IV) casting post (CP) and core with CMR (CP-CMR), (V) PFP-CLPF, (VI) PEFRC-CLPF, (VII) CP-CLPF, (VIII) PFP-CLF, (IX) PEFRC-CLF, and (X) CP-CLF. After thermomechanical loading, the fracture resistance and failure mode were assessed. Data were analyzed statistically (α = 0.05). RESULTS: In all post and core systems, the CLPF approach had lower fracture resistance than CMR (p < 0.05); CLF showed higher fracture resistance than CLPF only in the PFP system (p = 0.038). In PEFRC and CP systems, the difference between CLF and CLPF was not significant (p > 0.05). No significant difference was found in fracture resistance of different post and core systems with the same preparation approach (p > 0.05). CLPF showed the highest frequency of favorable, and CLF showed the highest frequency of unfavorable fractures. CONCLUSION: CLPF yielded lower fracture resistance than CMR. The difference in fracture resistance was not significant between CLF and CMR but the frequency of unfavorable fractures was higher in CLF than in other groups.

Color reproduction trueness of 3D-printed full-color dental casts with scans derived from an intraoral scanner.

PURPOSE: To investigate the effects of shade tab color variations (tooth-colored vs. gingiva-colored) and surface treatment (application of mineral oil) on the trueness of color reproduction from dental shade tabs to 3D-printed full-color dental casts, using digital scans obtained from an intraoral scanner. MATERIALS AND METHODS: Pristine tooth-colored (with 16 shade tabs) and gingiva-colored (with five shade tabs) shade guides were digitally scanned using an intraoral scanner, and subsequently, 3D-printed replicas were created using a full-color material jetting 3D printer. Three color measurements using a contact type digital spectrophotometer were recorded, including actual shade tabs (R0), dried 3D-printed study samples (RP1 ), and study samples with mineral oil application (RP2 ), in this study to calculate color differences between the actual shade tabs and 3D-printed ones. The CIEDE2000 formula was used to calculate the color differences (color reproduction trueness) between reference shade tabs and 3D-printed full-color study samples-without and with mineral oil, ∆E00 (RP1 ), and ∆E00 (RP2 ). ∆E00 (RP1 ) and ∆E00 (RP2 ) were compared with a 50:50% accessibility threshold (AT) and a 50:50% perceptibility threshold (PT). A grading system, based on the relative ranges of AT and PT, was employed. The percentage of samples falling into each color-matching category was then recorded. The data collected were subjected to statistical analysis, utilizing a mixed model ANOVA to evaluate the effects of shade tab color and mineral oil application on color differences, α = 0.05. RESULTS: The application of mineral oil significantly affected the ∆E00 [F(1, 378) = 19.1, p = < 0.0001]. However, this effect was only significant for the gingiva-colored study samples; the mineral oil application significantly decreased color difference, showing ∆E00 (RP1 ) of 8.71 ± 3.78 and ∆E00 (RP2 ) of 6.55 ± 2.14 (p < 0.0001). For the tooth-colored groups, the mineral oil application did not yield any color difference, showing ∆E00 (RP1 ) of 7.05 ± 2.35 and ∆E00 (RP2 ) of 6.94 ± 2.35 (p = 0.497). In the absence of mineral oil, gingiva-colored samples revealed a significantly larger ∆E00 (RP1 ) of 8.71 ± 3.78 compared to tooth-colored samples at 7.05 ± 2.35 (p = 0.017). Conversely, mineral oil application rendered comparable ∆E00 (RP2 ) values between gingiva-colored (6.55 ± 2.14) and tooth-colored (6.94 ± 2.35) samples (p = 0.558). All 3D-printed full-color samples showed Grade 1 (extremely unacceptable mismatch) and Grade 2 (clearly unacceptable mismatch), regardless of the shades or the presence of mineral oil. CONCLUSIONS: Utilizing an intraoral scanner to gather digital color data, along with an MJ 3D printer, offers the potential for producing 3D-printed full-color dental casts for prosthesis characterization in the dental laboratory. While mineral oil improves the color reproduction trueness of gingiva-colored objects, all 3D-printed full-color samples exhibited unacceptable mismatches when compared to their target objects. This underscores the need for future improvement in the digital color data acquisition process and color optimization protocols in 3D printing processes.

Influence of Light-Curing Glaze and Chlorhexidine Gluconate in the Acrylic Resin Properties: An in situ Study.

This in-situ study aimed to evaluate the chromatic stability, microhardness, and surfacefree energy of chemically activated acrylic resin (CAAR) samples. Eighty CAAR samples were made and each volunteer (n = 20) received two palatal plates with two sides of groups (without and with glaze application). The samples were exposed to two conditions: the control condition (sucrose 30%) and the test condition (sucrose 30% and 0.12% chlorhexidine). The volunteers used the first palatal device (control condition) for seven days and the second palatal device (test condition) for another seven days, with a seven-day break between them. Then, the ΔΕ00, microhardness, and surface-free energy tests were performed. Analysis of Variance and the Tukey test were used (α = 0.05). The control group with glaze showed higher ΔΕ00 compared to the group without the glaze. The test group with glaze had less ΔΕ00 than their respective controls. In both periods, when the glaze was applied, higher microhardness values were found for all groups. Groups with glaze showed lower roughness and higher surface-free energy than groups without the glaze. The values obtained in this study were satisfactory, showing the clinical efficacy of glaze and the use of 0.12% CH for maintaining the physical and mechanical properties of CAAR.

Comparison of methods for the handling of metallic dental restorations before head and neck radiotherapy.

PURPOSE: During head and neck radiotherapy, backscatter from metallic dental restorations (MDRs) causes oral mucositis. Currently, two MDR handling methods are used: the replacement of MDRs with provisional restorations (MDR removal) and fabrication of dental spacers before radiotherapy. We compared the effects of these two methods on the incidence of oral mucositis during head and neck radiotherapy. METHODS: We enrolled 76 patients with MDRs who underwent radiotherapy for head and neck cancer between April 2016 and March 2020. We set grade 2 oral mucositis as an outcome. After adjustment of all covariates using the propensity score (PS), we analyzed the data using a Cox proportional hazards model. In addition, subgroup analysis was performed by stratifying the data into quintiles based on the PS. RESULTS: For the incidence of grade 2 oral mucositis due to head and neck radiotherapy, the hazard ratio for the MDR removal group relative to the dental spacer group was 0.344 (95% confidence interval, 0.121-0.980; P = 0.046). Subgroup analysis showed that the hazard ratio for the MDR removal group was 0.339 (95% confidence interval, 0.122-0.943; P = 0.038). CONCLUSION: The results suggest that MDR replacement is superior to dental spacer fabrication in reducing the incidence of oral mucositis during head and neck radiotherapy, although MDR removal carries several associated risks.

Innovation Glass-Ceramic Spray Deposition Technology Improving the Adhesive Performance for Zirconium-Based Dental Restorations.

Glass-ceramic spray deposition (GCSD) is a novel technique for coating lithium disilicate (LD) glass-ceramics onto zirconia through simple tempering steps. GCSD has been proven to improve the bonding of zirconia to resin cement, but the effect of etching time on GCSD and the long-term durability of the bond achieved remain unknown. The effects of air abrasion with aluminum particles (ABB) and air abrasion (GAB) or etching with 5.0% hydrogen fluoride (HF) for 20, 60, 90, and 120 s (G20, G60, G90, and G120) on the resin cement−zirconia bond were studied. LD was included as a control (LDG). The microstructure, sub-micron roughness, wettability, and phase changes of samples were analyzed. After resin cement was bonded to zirconia, half of the samples were subjected to thermocycling (5000 cycles at 5−55 °C). The bond strengths of the samples were determined in shear bond strength (SBS) tests (n = 10 per group). An LD structure can be formed on zirconia after GCSD and proper etching processes, which result in high roughness and a hydrophilic nature. GCSD and HF etching significantly improved SBS, with G90 and G120 samples with pre- or post-thermocycling exhibiting SBS values comparable to those of LDG (p > 0.760). The surface characteristics of the LD layer are influenced by the etching time and affect the SBS of the bond of zirconia to resin cement. HF etching for 90−120 s after GCSD results in zirconia with SBS and bond durability comparable to LD.

Effects of irradiation, restoration and crown fracture type on the maximum load to fracture traumatized incisors: An ex vivo study.

BACKGROUND/AIMS: Radiotherapy makes teeth prone to tooth fractures. However, the relationship between radiotherapy and maximum load to fracture teeth that suffered a crown fracture is not fully understood. The aim of this study was to evaluate the influence of fracture type, radiation dose, fracture time, and their interactions on maximum load to fracture irradiated teeth. MATERIAL AND METHODS: A total of 140 permanent incisors were divided into two fracture type groups (uncomplicated and complicated) each of which included seven radiation dose subgroups (0, 10, 20, 30, 40, 50, and 60). The test groups were exposed to high-energy X-ray at 2 Gy/day, 5 days/week for a total dose of 10-60 Gy. Control groups were not irradiated. The load where the specimen started to break was obtained two different times. The 1st fracture was performed after radiation therapy, and the 2nd fracture was performed after the restoration of these samples. RESULTS: Fracture type had no effect on the maximum load to fracture. In contrast, the maximum load to fracture teeth decreased with increasing radiation doses. Maximum load to fracture the restored teeth was lower than the 1st fracture results. The general linear model procedure revealed a significant interaction between radiation dose and fracture time. Similarly, there was a significant interaction between the fracture type, radiotherapy dose, and fracture time. Maximum load values of teeth with complicated crown fractures restored with fiber posts and composite were not affected by radiation. CONCLUSION: Teeth that have been subjected to radiotherapy have an increased risk of fracture during dental trauma. However, restoration of the irradiated teeth with fiber posts and composite resin did not affect the maximum load required to fracture them.

Evaluation of the marginal adaptation and gingival status of full-crown restorations using an intraoral camera.

OBJECTIVE: The purpose of this study was to compare the usefulness of intraoral photographs, acquired with a household intraoral camera operating in conventional, calibrated, and polarized modes, with clinical examinations for assessing the marginal adaptation and gingival status of full-crown restorations. METHODS: Clinical examinations were performed by a prosthodontist who classified the marginal adaptation of full-crown restorations according to FDI World Dental Federation criteria, and a periodontal expert who classified gingival status according to the Modified Gingival Index (MGI). The margins and gingival status of the conventional, calibration, and polarization groups of full-crown restorations were independently assessed by three evaluators who obtained photographs using an intraoral camera. Cases where at least two of three assessors were in agreement were analyzed using Cohen's kappa coefficient and the chi-square test, and the sensitivity and specificity were calculated. RESULTS: The conventional, calibration, and polarization groups differed significantly in marginal and gingival status of full-crown restorations. In the calibration group, there was good agreement between the camera-based and oral clinical examinations in terms of the gingival status of full-crown restorations (kappa = 0.945), with 100% sensitivity and 91.67% specificity; this was also the case in the polarization group with respect to the margins of full-crown restorations (kappa = 0.917, sensitivity = 97.22%, specificity = 94.44%). CONCLUSIONS: An intraoral camera with black and white calibrated images is useful to assess the gingival status of full-crown restorations. Polarization mode can be used to assess the marginal adaptation of full-crown restorations. The camera is a feasible and valid diagnostic aid.

Effect of glaze and chlorhexidine on physical and mechanical properties of bis-acryl resin: An in situ study.

BACKGROUND: Temporary prosthesis protects the oral tissues, in addition to providing aesthetic look and masticatory function until a definitive prosthesis is manufactured. OBJECTIVES: To evaluate the effect of glaze and 0.12% chlorhexidine (CHX) on the physical and mechanical properties of bis-acryl, and to evaluate the antimicrobial efficacy of CHX. MATERIAL AND METHODS: Eighty specimens of bis-acryl resin were made. Over 40 of them the glaze was applied. One specimen with and 1 specimen without glaze were placed in niches of an appliance manufactured for each patient. Each of the 20 volunteers received 2 devices. Initially, the volunteers used one device and treated it with sucrose for 7 days (control), and later they used the other device and treated it with sucrose and CHX for 7 days (test). Color, microhardness, roughness, surface energy, and insoluble extracellular polysaccharides (EPS) tests were performed. All results were submitted to the Tukey's test, with the exception of the EPS results, which were submitted to the Student's t test. RESULTS: The ΔE00 of the unglazed control group was significantly higher than that of the unglazed test group. In all groups, a significant decrease in microhardness occurred over time. At both times, the glaze significantly increased the microhardness of the specimens (in all the glazed groups). At the final time, the test glaze group showed significantly higher microhardness compared with the control glaze group. Roughness in the groups without glaze increased significantly with CHX treatment over time. At both times, the glaze generated a significant reduction in roughness in the control and test groups. There was a significant reduction in surface energy over time in all groups. In most comparisons, the glazed groups showed significantly higher surface energy values compared with the unglazed control group. At the final time point, the unglazed test group showed a significantly higher surface energy value than the unglazed control group; and the glazed test group showed a significantly higher surface energy value compared with the glazed control group. The resins that received CHX had a significantly lower amount of biofilm. CONCLUSIONS: Color values were clinically acceptable in all tested groups. At both time points, the roughness values were clinically acceptable only in the glazed groups. Glaze increased the microhardness of the specimens. Microhardness and surface energy were reduced over time in all groups. Chlorhexidine can help prevent microhardness degradation. Glaze and CHX can increase surface energy. Chlorhexidine reduced the amount of bacterial biofilm.

Dental Applications of Carbon Nanotubes.

Glass ionomer cements and resin-based composites are promising materials in restorative dentistry. However, their limited mechanical properties and the risk of bulk/marginal fracture compromise their lifespan. Intensive research has been conducted to understand and develop new materials that can mimic the functional behavior of the oral cavity. Nanotechnological approaches have emerged to treat oral infections and become a part of scaffolds for tissue regeneration. Carbon nanotubes are promising materials to create multifunctional platforms for dental applications. This review provides a comprehensive survey of and information on the status of this state-of-the-art technology and describes the development of glass ionomers reinforced with carbon nanotubes possessing improved mechanical properties. The applications of carbon nanotubes in drug delivery and tissue engineering for healing infections and lesions of the oral cavity are also described. The review concludes with a summary of the current status and presents a vision of future applications of carbon nanotubes in the practice of dentistry.

Influence of selective caries excavation on marginal penetration of class II composite restorations in vitro.

Selective caries excavation may support pulp preservation. This in vitro study investigated the influence of selective removal of demineralized dentin on marginal integrity of composite restorations as determined by dye penetration. Dentinal caries-like lesions were produced in the approximal surfaces of 40 extracted human molars (ethylenediaminetetraacetate, 0.5 M, 96 h). The following test procedures were established: complete excavation, selective excavation, and caries-free control. Two class II cavities with enamel at the cervical margins were prepared per tooth and demineralization volume was determined by micro-computed tomography for the purpose of a stratified distribution to receive complete excavation or selective excavation. After complete or selective excavation (30 cavities each), adhesive composite restorations were placed. Cavities without demineralized dentin (20 cavities) served as control. The marginal integrity of restorations was evaluated by dye penetration with and without thermocycling or mechanical loading. Results were analyzed by non-parametrical statistical tests (Mann-Whitney U Test) with an α = 0.05 level of significance. Dye penetration did not differ significantly among completely excavated, selectively excavated, or undemineralized teeth, but was increased by thermocycling and mechanical loading in all experimental groups. Selective caries removal did not increase marginal penetration in class II restorations. The presence of remaining demineralized dentin surrounded by sound dentin did not impair marginal integrity of restorations with margins placed in sound enamel.

Effect of margin design on fracture load of zirconia crowns.

Zirconia-based restorations are showing an increase as the clinicians' preferred choice at posterior sites because of the strength and esthetic properties of such restorations. However, all-ceramic restorations fracture at higher rates than do metal-based restorations. Margin design is one of several factors that can affect the fracture strength of all-ceramic restorations. The aim of this study was to assess the effect of preparation and crown margin design on fracture resistance. Four groups of bilayer zirconia crowns (with 10 crowns in each group) were produced by hard- or soft-machining technique, with the following four different margin designs: chamfer preparation (control); slice preparation; slice preparation with an additional cervical collar of 0.7 mm thickness; and reduced occlusal thickness (to 0.4 mm) on slice preparation with an additional cervical collar of 0.7 mm thickness. Additionally, 10 hard-machined crowns with slice preparation were veneered and glazed with feldspathic porcelain. In total, 90 crowns were loaded centrally in the occlusal fossa until fracture. The load at fracture was higher than clinically relevant mastication loads for all preparation and margin designs. The crowns on a chamfer preparation fractured at higher loads compared with crowns on a slice preparation. An additional cervical collar increased load at fracture for hard-machined crowns.

Microleakage Evaluation of an Alkasite Restorative Material: An In Vitro Dye Penetration Study.

AIM: The aim of the present in vitro study was to comparatively evaluate the microleakage in three different esthetic restorative materials in class I cavities using the dye penetration technique. MATERIALS AND METHODS: Class I cavities were prepared on 24 human maxillary premolar teeth. The teeth were randomly divided into four groups of six samples each. Group I: Cention-N without adhesive (Ivoclar Vivadent, India), group II: Cention with adhesive (Ivoclar Vivadent, India), group III: type IX glass ionomer cement (Fuji), group IV: posterior composite (3M ESPE). The specimens were polished, subjected to thermocycling, and suspended in methylene blue dye for 24 hours. The teeth were sectioned longitudinally and the extent of microleakage was evaluated using the stereomicroscope. RESULTS: The results were subjected to statistical analysis using the Pearson's Chi-square test and the interobserver variability was assessed by the Kappa test for interobserver variability. The analysis showed statistically significant results among the groups. Although, Cention N with adhesive showed the least microleakage followed by Cention N without adhesive. CONCLUSION: All the materials tested were unable to completely eliminate microleakage in class I cavities. However, the newer alkasite material Cention N proved to have the least microleakage among all groups. CLINICAL SIGNIFICANCE: According to the present study, Cention N, a newer alkasite restorative material, demonstrated promising results with the least microleakage in comparison with posterior resin composites and glass ionomer cements. How to cite this article: Kini A, Shetty S, Bhat R, et al. Microleakage Evaluation of an Alkasite Restorative Material: An In Vitro Dye Penetration Study. J Contemp Dent Pract 2019;20(11):1315-1318.

Success of Dental Treatments under Behavior Management, Sedation and General Anesthesia.

Objective: To present comparative data with the aim of assisting the practitioner to choose between behavior modification (BM) techniques, pharmacologic sedation (N2O-O2 alone or combined with midazolam 0.5 mg/kg) or routine general anesthesia (GA) for the most successful approach in enabling pediatric dental care. Study design: Dental records of 56 children treated in a university dental clinic between 2006-2016 were reviewed, and data on age, gender, required treatment (amalgam restorations, composite restorations, pulpotomy, and stainless steel crowns [SSC]), treatment approaches and therapeutic success at final follow-up were retrieved. Results: Treatment under GA had the best success rates compared to both BM and pharmacologic sedation. N2O-O2 alone had a 6.1-fold greater risk of failure compared to N2O-O2+midazolam (p- <0.008). Amalgam restorations had a 2.61-fold greater risk of failure than SSC (p- <0.008). Conclusions: The GA mode yielded significantly greater success than the N2O-O2 mode alone. There were no significant differences in success rates between GA and combined midazolam 0.5 mg/kg+N2O-O2. When choosing restoration material, it is important to remember the high success rate of SSC compared to amalgam restoration.

Dental prostheses and tooth-related factors.

OBJECTIVES: This narrative review summarizes the current evidence about the role that the fabrication and presence of dental prostheses and tooth-related factors have on the initiation and progression of gingivitis and periodontitis. FINDINGS: Placement of restoration margins within the junctional epithelium and supracrestal connective tissue attachment can be associated with gingival inflammation and, potentially, recession. The presence of fixed prostheses finish lines within the gingival sulcus or the wearing of partial, removable dental prostheses does not cause gingivitis if patients are compliant with self-performed plaque control and periodic maintenance. However, hypersensitivity reactions to the prosthesis dental material can be present. Procedures adopted for the fabrication of dental restorations and fixed prostheses have the potential to cause traumatic loss of periodontal supporting tissues. Tooth anatomic factors, root abnormalities, and fractures can act as plaque-retentive factors and increase the likelihood of gingivitis and periodontitis. CONCLUSIONS: Tooth anatomic factors, such as root abnormalities and fractures, and tooth relationships in the dental arch and with the opposing dentition can enhance plaque retention. Restoration margins located within the gingival sulcus do not cause gingivitis if patients are compliant with self-performed plaque control and periodic maintenance. Tooth-supported and/or tooth-retained restorations and their design, fabrication, delivery, and materials have often been associated with plaque retention and loss of attachment. Hypersensitivity reactions can occur to dental materials. Restoration margins placed within the junctional epithelium and supracrestal connective tissue attachment can be associated with inflammation and, potentially, recession. However, the evidence in several of the reviewed areas, especially related to the biologic mechanisms by which these factors affect the periodontium, is not conclusive. This highlights the need for additional well-controlled animal studies to elucidate biologic mechanisms, as well as longitudinal prospective human trials. Adequate periodontal assessment and treatment, appropriate instructions, and motivation in self-performed plaque control and compliance to maintenance protocols appear to be the most important factors to limit or avoid potential negative effects on the periodontium caused by fixed and removable prostheses.

Periodontal manifestations of systemic diseases and developmental and acquired conditions: Consensus report of workgroup 3 of the 2017 World Workshop on the Classification of Periodontal and Peri-Implant Diseases and Conditions.

BACKGROUND: A variety of systemic diseases and conditions can affect the course of periodontitis or have a negative impact on the periodontal attachment apparatus. Gingival recessions are highly prevalent and often associated with hypersensitivity, the development of caries and non-carious cervical lesions on the exposed root surface and impaired esthetics. Occlusal forces can result in injury of teeth and periodontal attachment apparatus. Several developmental or acquired conditions associated with teeth or prostheses may predispose to diseases of the periodontium. The aim of this working group was to review and update the 1999 classification with regard to these diseases and conditions, and to develop case definitions and diagnostic considerations. METHODS: Discussions were informed by four reviews on 1) periodontal manifestions of systemic diseases and conditions; 2) mucogingival conditions around natural teeth; 3) traumatic occlusal forces and occlusal trauma; and 4) dental prostheses and tooth related factors. This consensus report is based on the results of these reviews and on expert opinion of the participants. RESULTS: Key findings included the following: 1) there are mainly rare systemic conditions (such as Papillon-Lefevre Syndrome, leucocyte adhesion deficiency, and others) with a major effect on the course of periodontitis and more common conditions (such as diabetes mellitus) with variable effects, as well as conditions affecting the periodontal apparatus independently of dental plaque biofilm-induced inflammation (such as neoplastic diseases); 2) diabetes-associated periodontitis should not be regarded as a distinct diagnosis, but diabetes should be recognized as an important modifying factor and included in a clinical diagnosis of periodontitis as a descriptor; 3) likewise, tobacco smoking - now considered a dependence to nicotine and a chronic relapsing medical disorder with major adverse effects on the periodontal supporting tissues - is an important modifier to be included in a clinical diagnosis of periodontitis as a descriptor; 4) the importance of the gingival phenotype, encompassing gingival thickness and width in the context of mucogingival conditions, is recognized and a novel classification for gingival recessions is introduced; 5) there is no evidence that traumatic occlusal forces lead to periodontal attachment loss, non-carious cervical lesions, or gingival recessions; 6) traumatic occlusal forces lead to adaptive mobility in teeth with normal support, whereas they lead to progressive mobility in teeth with reduced support, usually requiring splinting; 7) the term biologic width is replaced by supracrestal tissue attachment consisting of junctional epithelium and supracrestal connective tissue; 8) infringement of restorative margins within the supracrestal connective tissue attachment is associated with inflammation and/or loss of periodontal supporting tissue. However, it is not evident whether the negative effects on the periodontium are caused by dental plaque biofilm, trauma, toxicity of dental materials or a combination of these factors; 9) tooth anatomical factors are related to dental plaque biofilm-induced gingival inflammation and loss of periodontal supporting tissues. CONCLUSION: An updated classification of the periodontal manifestations and conditions affecting the course of periodontitis and the periodontal attachment apparatus, as well as of developmental and acquired conditions, is introduced. Case definitions and diagnostic considerations are also presented.

Success of Dental Treatments under Behavior Management, Sedation and General Anesthesia.

OBJECTIVE: To present comparative study aims to assist the practitioner to choose between behavior modification (BM) techniques, pharmacologic sedation (N2O-O2 alone or combined with midazolam 0.5 mg/ kg) or routine general anesthesia (GA) for the most successful approach in enabling pediatric dental care. STUDY DESIGN: Dental records of 56 children treated in a university dental clinic between 2006-2016 were reviewed, and data on age, gender, required treatment (amalgam restorations, composite restorations, pulpotomy, and stainless steel crowns [SSC]), treatment approaches and therapeutic success at final follow-up were retrieved. RESULTS: Treatment under GA had the best success rates compared to both BM and pharmacologic sedation. N2O-O2 alone had a 6.1-fold greater risk of failure compared to N2O-O2+midazolam (p- <0.008). Amalgam restorations had a 2.61-fold greater risk of failure than SSC (p- <0.008). CONCLUSIONS: The GA mode yielded significantly greater success than the N2O-O2 mode alone. There were no significant differences in success rates between GA and combined midazolam 0.5 mg/kg+N2O-O2. When choosing restoration material, it is important to remember the high success rate of SSC compared to amalgam restoration.