Characteristics of expanded polystyrene microplastics on island beaches in the Pearl River Estuary: abundance, size, surface texture and their metals-carrying capacity.

While expanded polystyrene (EPS) microplastics have been widely recognized as one of the most important components of plastic litter in the intertidal zones of the global ocean, our understanding of their environmental fate on island beaches is insufficient. In this study, we intended to reveal that the latest EPS microplastic pollution status on 5 island beaches in the Pearl River Estuary, China, by comprehensively assessing the abundance, distribution, size, surface texture and carrying capacity of heavy metals (Cd, As, Cr, Ni, Cu, Pb, Mn, Fe, Al). High level of EPS microplastic abundance ranged from 328 to 82,276 particles m-2 was found, with the highest abundance at Guishan Island and the lowest at Dong'ao Island. Spatial distribution of EPS microplastic abundance was significantly different among different islands. EPS microplastics in the size range of 1-2 mm were the most abundant. The content of heavy metals in EPS microplastics collected on the beaches was greater than that in the new EPS products. The average concentrations of heavy metals in EPS microplastics from 5 islands are Cd (0.27 ± 0.19 µg g-1), As (5.50 ± 3.84 µg g-1), Cr (14.9 ± 8.25 µg g-1), Cu (15.0 ± 7.66 µg g-1), Ni (17.2 ± 17.6 µg g-1), Pb (24.8 ± 7.39 µg g-1), Mn (730 ± 797 µg g-1), Fe (8340 ± 4760 µg g-1), and Al (9624 ± 6187 µg g-1), respectively. The correlation between heavy metals in EPS microplastics and sediments was better than that between heavy metals in EPS microplastics and seawater. The study results indicated that EPS microplastics could act as a carrier for the transport of heavy metals, which might pose a threat to biological and human health.

The deciphering of microplastics-derived fluorescent dissolved organic matter in urban lakes, canals, and rivers using parallel factor analysis modeling and mimic experiment.

The aim of the study is to investigate the leaching of fluorescent dissolved organic matter (fDOM) from microplastics. In addition, this study identifies the connection between fDOM and microplastics in the aquatic environment. Three-dimensional excitation-emission matrix identified five fluorophores, that is, peak A, M, T, Tuv, and Wuv, and the parallel factor analysis modeling identified five components, that is, tryptophan-like, p-hydroxy acetophenone, humic acid (C-like), detergent-like, and fulvic acid (M-like) in the urban surface water. Mimic experiments using commonly used synthetic plastic (like microplastics) in Mili-Q water under solar radiation and dark environments demonstrate the release of fDOM from plastic. Two fluorophore peaks were observed at Ex/Em = 250/302 nm and Ex/Em = 260/333 nm for the expanded polystyrene plastic polymer and one fluorophore peak at Ex/Em = 260/333 nm for the low-density polyethylene. Fluorophore and component intensity exhibited notable associations with microplastics in the aquatic environment. These findings indicated that the characteristics and dynamics of fDOM in urban surface water are influenced by microplastics. PRACTITIONER POINTS: Fluorescent dissolved organic matters were identified in urban surface waters. Expanded polystyrene (EPS) had shown two fluorophores at Em/Ex = 250/302 and Em/Ex = 260/333. Low-density polyethylene (LDPE) had one fluorophore at Em/Ex = 260/333. Fluorophore and component intensity in the aquatic settings exhibited associations with microplastics.

Comparative Study on Selected Insulating Materials for Industrial Piping.

This paper describes the results of an experimental assessment of the thermal conductivity of pipe insulation. The need for reducing energy loss in industrial piping systems makes the availability of relevant and reliable insulation materials of special importance. Several specimens of pipe laggings, made of different materials, including mineral wool, polyethylene foam (PEF), expanded polystyrene (EPS), flexible elastomeric foam (FEF) and polyurethane foam (PUR), were tested in accordance with the European standard ISO 8497. The thermal conductivity of the materials was measured for a wide range of temperatures. The results were compared with the values reported in the technical specifications as well as with the literature data. The assessment of measurement uncertainty was also described. The results showed that, in a few cases, thermal conductivity turned out to be greater than that declared by the manufacturer by as much as over 10%.

Biodegradation of polystyrene (PS) by marine bacteria in mangrove ecosystem.

Plastics pollution poses a new threat to marine ecosystems. Mangrove locating at estuary worldwide is probably the most heavily polluted area trapping various plastics transported from terrestrial and nearby marine aquaculture. Expanded polystyrene (EPS) is one of most common plastic debris therein and even in the plastic garbage. Here we showed the bacterial diversity of the polystyrene-degrading microbial community from EPS waste sites from a subtropical mangrove area. After enrichment with EPS, the degradation consortia were obtained. They shared a similar community structure dominated by bacteria of Sphingomonadaceae, Rhodanobacteraceae, Rhizobiaceae, Dermacoccaceae, Rhodocyclaceae, Hyphomicrobiaceae, and Methyloligellaceae. Diverse bacteria standing for the first member of the genera of Novosphingobium, Gordonia, Stappia, Mesobacillus, Alcanivorax, Flexivirga, Cytobacillus, Thioclava, and Thalassospira showed PS degradation capability as a pure culture. Further, PS biodegradation of Gordonia sp. and Novosphingobium sp. was quantified by weight loss, in addition to obvious morphological and structural changes of the PS films observed by SEM, ATR-FTIR, and contact angle analysis. The formation of new oxygen-containing functional groups implied the degradation pathway of oxidation. Although the degradation rates ranged from 2.7% to 7.7% after one month in lab and possibly lower in situ, their role in EPS removal is unneglectable.

Optimizing the Composition Design of Cement-Based Expanded-Polystyrene (EPS) Exterior Wall Based on Thermal Insulation and Flame Retardance.

The use of thermal insulated decorative panel materials with low thermal conductivity and high flame retardance is a key step toward energy-saving buildings. However, traditional thermal insulation materials are always highly conductive and inflammable, which restricts their application for new buildings. This study aims to prepare the non-combustible, cement-based EPS mixtures with thermal conductivity lower than 0.045 and density less than 140 kg/m3 and characterize it with mechanical, thermal, and flame retardant properties. The effect of particle size, Silica coated and content of EPS on the physical, mechanical, thermal, and combustion performance are conducted in this paper. The comprehensive indoor tests including density, water absorbing, softening coefficient, compressive strength, tensile strength, moisture susceptibility, thermal conductivity, and scanning electron microscopy (SEM) along with combustion performance are reported to evaluate the effects of several variables on the investigated cement-based nonflammable EPS (CEPS)mixtures. The results show that small and gradation EPS particles significantly improve the comprehensive performance of mixtures. In addition, Silica coated ESP significantly improve the flame retardance of mixtures while reduce the mechanical characteristics slightly. These results contribute to the selection of appropriate materials to enhance the thermal insulation, flame retardance and mechanical properties of CEPS.

X-ray Computed Tomography for Characterization of Expanded Polystyrene (EPS) Foam.

Expanded polystyrene (EPS) foam is widely used in building and construction applications for thermal and acoustic insulation. This material is nearly transparent for X-rays, making it difficult to characterize its pore structure in 3D with X-ray tomography. Because of this difficulty, the pore network is often not investigated and is, thus, poorly known. Since this network controls different physical properties, such as the sound absorption, it is crucial to understand its overall structure. In this manuscript, we show how to reveal the pore network of EPS foams through the combination of high resolution X-ray tomography (micro-CT) and saturation techniques. The foams were saturated with CsCl-brine, which acts as a contrasting agent in X-ray micro-CT imaging. This allowed us to separate the beads, making up the foam, from the pore network. Based on the 3D micro-CT results, we were able to assess a representative elementary volume for the polystyrene, which allows for calculating the acoustical parameters from the Johnson-Champoux-Allard (JCA) model, the pore and bead size distribution. The 3D data was also used as input to simulate sound absorption curves. The parametric study showed that an increase in the bead size influenced the sound absorption of the material. We showed that, by doubling the diameter of beads, the absorption coefficient was doubled in certain ranges of frequency.

Study on the Fatigue and Durability Behavior of Structural Expanded Polystyrene Concretes.

The fatigue and durability characteristics of structural expanded polystyrene concrete (EPS) are especially important when it was applied for structural elements in long-term service. In order to study the fatigue and durability behavior of structural EPS concrete, the long-term cyclic loading experiments and wetting-drying (W-D) cyclic experiments were conducted, respectively. The structural EPS concrete was found to have a relatively large damping and a fairly low dynamic elastic modulus under long-term cyclic load, which illustrated that it had a better energy absorption effect and toughness than plain concrete of the same strength level. Even if fine cracks appeared during the cyclic loading process, the relevant dynamic performance remained stable, which indicated that the structural EPS concrete had superior fatigue stability. In W-D cyclic experiments, the structural EPS concrete exhibited superior sulfate resistance. During the erosion test process, there was a positive correlation between the mass change and the evolution of the compressive strength of the structural EPS concrete, which indicated that ΔmB could be substituted for Δf to evaluate the degree of the structural EPS concrete eroded by sulfate attack. The study focuses on the fatigue performance and sulfate resistance of structural EPS concrete and is of important engineering value for promoting practical long-term operations.