Insights into the Mechanism of Selective Removal of Heavy Metal Ions by the Pulsed/Direct Current Electrochemical Method.

Heavy metal pollution treatment in industrial wastewater is crucial for protecting biological and environmental safety. However, the highly efficient and selective removal of heavy metal ions from multiple cations in wastewater is a significant challenge. This work proposed a pulse electrochemical method with a low-/high-voltage periodic appearance to selectively recover heavy metal ions from complex wastewater. It exhibited a higher recovery efficiency for heavy metal ions (100% for Pb2+ and Cd2+, >98% for Mn2+) than other alkali and alkaline earth metal ions (Na+, Ca2+, and Mg2+ were kept below 3.6, 1.3, and 2.6%, respectively) in the multicomponent solution. The energy consumption was only 34-77% of that of the direct current electrodeposition method. The results of characterization and experiment unveil the mechanism that the low-/high-voltage periodic appearance can significantly suppress the water-splitting reaction and break the mass-transfer limitation between heavy metal ions and electrodes. In addition, the plant study demonstrates the feasibility of treated wastewater for agricultural use, further proving the high sustainability of the method. Therefore, it provides new insights into the selective recovery of heavy metals from industrial wastewater.

Nanoscale Insights into the Interaction Mechanism Underlying the Adsorption and Retention of Heavy Metal Ions by Humic Acid.

The mobility and distribution of heavy metal ions (HMs) in aquatic environments are significantly influenced by humic acid (HA), which is ubiquitous. A quantitative understanding of the interaction mechanism underlying the adsorption and retention of HMs by HA is of vital significance but remains elusive. Herein, the interaction mechanism between HA and different types of HMs (i.e., Cd(II), Pb(II), arsenate, and chromate) was quantitatively investigated at the nanoscale. Based on quartz crystal microbalance with dissipation tests, the adsorption capacities of Pb(II), Cd(II), As(V), and Cr(VI) ionic species on the HA surface were measured as ∼0.40, ∼0.25, ∼0.12, and ∼0.02 nmol cm-2, respectively. Atomic force microscopy force results showed that the presence of Pb(II)/Cd(II) cations suppressed the electrostatic double-layer repulsion during the approach of two HA surfaces and the adhesion energy during separation was considerably enhanced from ∼2.18 to ∼5.05/∼4.18 mJ m-2. Such strong adhesion stems from the synergistic metal-HA complexation and cation-π interaction, as evidenced by spectroscopic analysis and theoretical simulation. In contrast, As(V)/Cr(VI) oxo-anions could form only weak hydrogen bonds with HA, resulting in similar adhesion energies for HA-HA (∼2.18 mJ m-2) and HA-As(V)/Cr(VI)-HA systems (∼2.26/∼1.96 mJ m-2). This work provides nanoscale insights into quantitative HM-HA interactions, improving the understanding of HMs biogeochemical cycling.

Heavy metal ion sensing strategies using fluorophores for environmental remediation.

The main aim of this review is to provide a holistic summary of the latest advances within the research area focusing on the detection of heavy metal ion pollution, particularly the sensing strategies. The review explores various heavy metal ion detection approaches, encompassing spectrometry, electrochemical methods, and optical techniques. Numerous initiatives have been undertaken in recent times in response to the increasing demand for fast, sensitive, and selective sensors. Notably, fluorescent sensors have acquired prominence owing to the numerous advantages such as good specificity, reversibility, and sensitivity. Further, this review also explores the advantages of various nanomaterials employed in sensing heavy metal ions. In this regard, exclusive emphasis is placed on fluorescent nanomaterials based on organic dyes, quantum dots, and fluorescent aptasensors for metal ion removal from aqueous systems, and to identify the fate of heavy metal ions in the natural environment.

In situ biosynthesized polyphosphate nanoparticles/reduced graphene oxide composite electrode for highly sensitive detection of heavy metal ions.

The development of an effective sensing platform is critical for the electrochemical detection of heavy metal ions (HMIs) in water. In this study, we fabricated a newly designed sensor through the in situ assembly of reduced graphene oxide (rGO) and polyphosphate nanoparticles (polyP NPs) on a carbon cloth electrode via microorganism-mediated green biochemical processes. The characterization results revealed that the rGO produced via microbial reduction had a three-dimensional porous structure, serving as an exceptional scaffold for hosting polyP NPs, and the polyP NPs were evenly distributed on the rGO network. In terms of detecting HMIs, the numerous functional groups of polyP NPs play a major role in the coordination with the cations. This electrochemical sensor, based on polyP NPs/rGO, enabled the individual and simultaneous determination of lead ion (Pb2+) and copper ion (Cu2+) with detection limits of 1.6 nM and 0.9 nM, respectively. Additionally, the electrode exhibited outstanding selectivity for the target analytes in the presence of multiple interfering metal ions. The fabricated sensor was successfully used to determine Pb2+/Cu2+ in water samples with satisfactory recovery rates ranging from 92.16% to 104.89%. This study establishes a facile, cost-effective, and environmentally friendly microbial approach for the synthesis of electrode materials and the detection of environmental pollutants.

Ultrafast and highly efficient Cd(II) and Pb(II) removal by magnetic adsorbents derived from gypsum and corncob: Performances and mechanisms.

The utilization of gypsum and biomass in environmental remediation has become a novel approach to promote waste recycling. Generally, raw waste materials exhibit limited adsorption capacity for heavy metal ions (HMIs) and often result in poor solid-liquid separation. In this study, through co-pyrolysis with corncob waste, titanium gypsum (TiG) was transformed into magnetic adsorbents (GCx, where x denotes the proportion of corncob in the gypsum-corncob mixture) for the removal of Cd(II) and Pb(II). GC10, the optimal adsorbent, which was composed primarily of anhydrite, calcium sulfide, and magnetic Fe3O4, exhibited significantly faster adsorption kinetics (rate constant k1 was 218 times and 9 times of raw TiG for Cd(II) and Pb(II)) and higher adsorption capacity (Qe exceeded 200 mg/g for Cd(II) and 400 mg/g for Pb(II)) than raw TiG and previous adsorbents. Cd(II) removal was more profoundly inhibited in a Cd(II) + Pb(II) binary system, suggesting that GC10 showed better selectivity for Pb(II). Moreover, GC10 could be easily separated from purified water for further recovery, due to its high saturation magnetization value (6.3 emu/g). The superior removal capabilities of GC10 were due to adsorption and surface precipitation of metal sulfides and metal sulfates on the adsorbent surface. Overall, these waste-derived magnetic adsorbents provide a novel and sustainable approach to waste recycling and the deep purification of multiple HMIs.

Electrochemical sensing platform for detection of heavy metal ions without electrochemical signal.

Heavy metal pollution has attracted global attention because of its high toxicity, non-biodegradability, and carcinogenicity. Electrochemical sensors are extensively employed for the detection of low concentrations of heavy metal ions (HMIs). However, their applicability is often limited to the detection of ions that exhibit electrochemical signals exclusively in aqueous solutions. In this study, we proposed a multi-responsive detection platform based on the modification of horseradish peroxidase@zeolitic imidazolate frameworks-8/thionine/gold/ionic liquid-reduced graphene oxide (HRP@ZIF-8/THI/Au/IL-rGO). This platform demonstrated its capability to detect various metal ions, including those without conventional electrochemical signals. The Au/IL-rGO composite structure enhanced the specific surface area available for the reaction. Furthermore, the in situ growth of HRP@ZIF-8 not only shielded the THI signal prior to detection but also protected the electrode material. It was important to note that the introduced edetate disodium dihydrate (EDTA) had the ability to complex with various HMIs. When excess EDTA was present, it could cleave ZIF-8 and release HRP. In the presence of hydrogen peroxide (H2O2), HRP promoted the oxidation of THI previously reduced by the electrode and thus showed excellent sensitivity for HMIs detection. The proposed method overcame the limitation of traditional electrochemical sensors, which solely relied on electrochemical signals for detecting metal ions. This offers a novel approach to enhance electrochemical ion sensing detection.

Fluorescent multichannel sensor array based on three carbon dots derived from Tibetan medicine waste for the quantification and discrimination of multiple heavy metal ions in water.

A fluorescent multichannel sensor array has been established based on three carbon dots derived from Tibetan medicine waste for rapid quantification and discrimination of six heavy metal ions. Due to the chelation between metal ions and carbon dots (CDs), this fluorescence "turn off" mode sensing array can quantify six metal ions as low as "µM" level. Moreover, the six heavy metal ions display varying quenching effects on these three CDs owing to diverse chelating abilities between each other, producing differential fluorescent signals for three sensing channels, which can be plotted as specific fingerprints and converted into intuitive identification profiles via principal component analysis (PCA) and hierarchical cluster analysis (HCA) technologies to accurately distinguish Cu2+, Fe3+, Mn2+, Ag+, Ce4+, and Ni2+ with the minimum differentiated concentration of 5 µM. Valuably, this sensing array unveils good sensitivity, exceptional selectivity, ideal stability, and excellent anti-interference ability for both mixed standards and actual samples. Our contribution provides a novel approach for simultaneous determination of multiple heavy metal ions in environmental samples, and it will inspire the development of other advanced optical sensing array for simultaneous quantification and discrimination of multiple targets.

Development of MOF-derived Co3O4 microspheres composed of fiber stacks for simultaneous electrochemical detection of Pb2+ and Cu2.

As an ideal transition metal oxide, Co3O4 is a P-type semiconductor with excellent electrical conductivity, non-toxicity and low cost. This work reports the successful construction of Co3O4 materials derived from metal-organic frameworks (MOFs) using a surfactant micelle template-solvothermal method. The modified electrodes are investigated for their ability to electrochemically detect Pb2+ and Cu2+ in aqueous environments. By adjusting the mass ratios of alkaline modifiers, the morphological microstructures of Co3O4-X exhibit a transition from distinctive microspheres composed of fiber stacks to rods. The results indicate that Co3O4-1(NH4F/CO(NH2)2 = 1:0) has a distinctive microsphere structure composed of stacked fibers, unlike the other two materials. Co3O4-1/GCE is used as the active material of the modified electrode, it shows the largest peak response currents to Pb2+ and Cu2+, and efficiently detects Pb2+ and Cu2+ in the aqueous environment individually and simultaneously. The linear response range of Co3O4-1/GCE for the simultaneous detection of Pb2+ and Cu2+ is 0.5-1.5 µM, with the limits of detection (LOD, S/N = 3) are 9.77 nM and 14.97 nM, respectively. The material exhibits a favorable electrochemical response, via a distinctive Co3O4-1 microsphere structure composed of stacked fibers. This structure enhances the number of active adsorption sites on the material, thereby facilitating the adsorption of heavy metal ions (HMIs). The presence of oxygen vacancies (OV) can also facilitate the adsorption of ions. The Co3O4-1/GCE electrode also exhibits excellent anti-interference ability, stability, and repeatability. This is of great practical significance for detecting Pb2+ and Cu2+ in real water samples and provides a new approach for developing high-performance metal oxide electrochemical sensors derived from MOFs.

Tungsten Oxide Coated Liquid Metal Electrodes via Galvanic Replacement as Heavy Metal Ion Sensors.

Gallium liquid metals (LMs) like Galinstan and eutectic Gallium-Indium (EGaIn) have seen increasing applications in heavy metal ion (HMI) sensing, because of their ability to amalgamate with HMIs like lead, their high hydrogen potential, and their stable electrochemical window. Furthermore, coating LM droplets with nanopowders of tungsten oxide (WO) has shown enhancement in HMI sensing owing to intense electrical fields at the nanopowder-liquid-metal interface. However, most LM HMI sensors are droplet based, which show limitations in scalability and the homogeneity of the surface. A scalable approach that can be extended to LM electrodes is therefore highly desirable. In this work, we present, for the first time, WO-Galinstan HMI sensors fabricated via photolithography of a negative cavity, Galinstan brushing inside the cavity, lift-off, and galvanic replacement (GR) in a tungsten salt solution. Successful GR of Galinstan was verified using optical microscopy, SEM, EDX, XPS, and surface roughness measurements of the Galinstan electrodes. The fabricated WO-Galinstan electrodes demonstrated enhanced sensitivity in comparison with electrodes structured from pure Galinstan and detected lead at concentrations down to 0.1 mmol·L-1. This work paves the way for a new class of HMI sensors using GR of WO-Galinstan electrodes, with applications in microfluidics and MEMS for a toxic-free environment.

Layer-by-Layer Immobilization of DNA Aptamers on Ag-Incorporated Co-Succinate Metal-Organic Framework for Hg(II) Detection.

Layer-by-layer (LbL) immobilization of DNA aptamers in the realm of electrochemical detection of heavy metal ions (HMIs) offers an enhancement in specificity, sensitivity, and low detection limits by leveraging the cross-reactivity obtained from multiple interactions between immobilized aptamers and developed material surfaces. In this research, we present a LbL approach for the immobilization of thiol- and amino-modified DNA aptamers on a Ag-incorporated cobalt-succinate metal-organic framework (MOF) (Ag@Co-Succinate) to achieve a cross-reactive effect on the electrochemical behavior of the sensor. The solvothermal method was utilized to synthesize Ag@Co-Succinate, which was also characterized through various techniques to elucidate its structure, morphology, and presence of functional groups, confirming its suitability as a host matrix for immobilizing both aptamers. The Ag@Co-Succinate aptasensor exhibited extraordinary sensitivity and selectivity towards Hg(II) ions in electrochemical detection, attributed to the unique binding properties of the immobilized aptamers. The exceptional limit of detection of 0.3 nM ensures the sensor's suitability for trace-level Hg(II) detection in various environmental and analytical applications. Furthermore, the developed sensor demonstrated outstanding repeatability, highlighting its potential for long-term and reliable monitoring of Hg(II).

Novel modified semi-carbonized fiber prepared using discarded clothes for derisking Cu(II) and Pb(II) contaminated water.

We report a novel modified semi-carbonized fiber (CF) prepared using cotton and acrylic clothes for derisking contaminated water to realize the resource utilization of discarded clothes in wastewater treatment. In this study, amphoteric and auxiliary modifiers were used to modify CFs for preparing amphoteric and amphoteric-auxiliary CFs. The basic physicochemical properties of different modified CFs were determined, and the microscopic morphology of modified CFs was detected. The isothermal adsorption characteristics of Cu(II) and Pb(II) on different modified CFs were investigated by the batch method, and the effect mechanisms of temperature, pH, ionic strength, and material dose were compared. Physicochemical properties and microscopic morphology results proved that amphoteric and auxiliary modifiers were modified on the CF surface and changed the surface properties of CF. The adsorption capacities of Cu(II) and Pb(II) on modified CFs increased with the increase in equilibrium concentration of Cu(II) and Pb(II), and the isotherm was more suitable for Freundlich model fitting than that of the Langmuir model. The maximum adsorption capacities (qm) of Cu(II) and Pb(II) on different modified CFs were 60.72-81.26 mg/g and 102.58-161.72 mg/g, respectively, and presented the trend of amphoteric-auxiliary CFs > amphoteric CFs > CFs. Increasing pH and temperature and decreasing ionic strength and material dose were beneficial to Cu(II) and Pb(II) adsorption. The Cu(II) and Pb(II) adsorption process was a spontaneous, endothermic, and entropy-increasing reaction, and the adsorption rate was controlled by chemisorption. The adsorption amount of amphoteric-auxiliary CFs maintained about 65% of original materials after 3 times of regeneration. Electrostatic attraction, precipitation, complexation, and ion exchange were the main adsorption mechanisms. The cation exchange capacity and total pore volume of modified CFs were key to determining qm of Cu(II) and Pb(II).

A novel composite electrode with multiple pore structures for efficient treatment of heavy metal ions in capacitive deionization.

Multiple porous carbon materials have great promise and potential in the capacitive deionization (CDI) field. Specific surface area (SSA), pore size distribution, and preparation method of CDI electrode materials are essential for the treatment of heavy metal ions. In this work, PPy composited porous carbon electrodes (hypercrosslinked polymers/polypyrrole, HCPs/PPy) were obtained by one-step crosslinked carbonization preparation and electro-deposition. The diverse pore structure gives the composite electrode a large SSA and excellent adsorption performance. HCPs/PPy-4 gives a high SSA of 251.26 m2/g. In the CDI process, the adsorption capacity of HCPs/PPy-4 for Fe3+, Cu2+, Pb2+, and Ag+ is 20.69 mg/g, 37.81 mg/g, 26.86 mg/g, and 40.95 mg/g. The negative electrode recoveries for the adsorption of the four ions were reached 81.2%, 89.2%, 85.5%, and 100%, respectively. It indicates that HCPs/PPy is a novel and potentially porous carbon electrode for high-performance CDI.

Application Prospect of Ion-Imprinted Polymers in Harmless Treatment of Heavy Metal Wastewater.

With the rapid development of industry, the discharge of heavy metal-containing wastewater poses a significant threat to aquatic and terrestrial environments as well as human health. This paper provides a brief introduction to the basic principles of ion-imprinted polymer preparation and focuses on the interaction between template ions and functional monomers. We summarized the current research status on typical heavy metal ions, such as Cu(II), Ni(II), Cd(II), Hg(II), Pb(II), and Cr(VI), as well as metalloid metal ions of the As and Sb classes. Furthermore, it discusses recent advances in multi-ion-imprinted polymers. Finally, the paper addresses the challenges faced by ion-imprinted technology and explores its prospects for application.

Recent advances and trends in innovative biosensor-based devices for heavy metal ion detection in food.

Low-cost, reliable, and efficient biosensors are crucial in detecting residual heavy metal ions (HMIs) in food products. At present, based on distance-induced localized surface plasmon resonance of noble metal nanoparticles, enzyme-mimetic reaction of nanozymes, and chelation reaction of metal chelators, the constructed optical sensors have attracted wide attention in HMIs detection. Besides, based on the enrichment and signal amplification strategy of nanomaterials on HMIs and the construction of electrochemical aptamer sensing platforms, the developed electrochemical biosensors have overcome the plague of low sensitivity, poor selectivity, and the inability of multiplexed detection in the optical strategy. Moreover, along with an in-depth discussion of these different types of biosensors, a detailed overview of the design and application of innovative devices based on these sensing principles was provided, including microfluidic systems, hydrogel-based platforms, and test strip technologies. Finally, the challenges that hinder commercial application have also been mentioned. Overall, this review aims to establish a theoretical foundation for developing accurate and reliable sensing technologies and devices for HMIs, thereby promoting the widespread application of biosensors in the detection of HMIs in food.

Adsorption efficiency of chitosan/clinoptilolite (CS/CZ) composite for effective removal of Cd+2 and Cr+6 ions from wastewater effluents of dairy cattle farms.

The wastewater effluent is responsible for the major ecological impact of the dairy sectors. To avoid the negative consequences of heavy metal pollution on the ecosystem, creative, affordable, and efficient treatment methods are now required before the effluent flows into the surrounding area. This study was aimed at assessing the effectiveness of three different adsorbents for Cd+2 and Cr+6 ions from wastewater effluents of dairy farms, including chitosan (CS), clinoptilolite zeolite (CZ), and chitosan/clinoptilolite zeolite (CS/CZ) composite. The adsorption kinetics of the CS/CZ composite were established using the effects of the key variables (pH, agitation speed, adsorbent concentrations, and contact durations). The removal (%) and adsorption capacities, qe (mg/g), were calculated using the data from the adsorption kinetics. Wastewater samples (n = 60) were collected from the wastewater effluents of five farms. Cd+2 and Cr+6 ion concentrations in all collected samples were determined. Following the CS/CZ composite creation, it was characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (X-RD), and Fourier-transform infrared spectrum (FT-IR). The CS/CZ composite had an adsorption capacity of 92.4 and 96.5 mg/g for both Cd+2 and Cr+6 ions at a concentration of 2.0 g/100 ml, respectively, while the CZ adsorption capacities for the two ions were 87.5 mg/g and 61.0 mg/g, respectively, at 4.0 g/100 ml concentration. The CS was achieved at 55.56 mg/g and 33.3 mg/g, respectively, at the same concentration. The efficiency of heavy metal removal was enhanced by increasing adsorbent concentration, agitation speed, and contact duration. Using CS/CZ composite at 2.0 g/100 ml concentration, 180 min of contact time, and 300 rpm agitation speed, the greatest removal efficiencies for Cd+2 and Cr+6 ions (96.43 and 98.75%, respectively) were demonstrated.

Enhanced removal of iron (Fe) and manganese (Mn) ions from contaminated water using graphene oxide-decorated polyethersulphone membranes: Synthesis and characterization.

This study addresses the urgent issue of water pollution caused by iron (Fe) and manganese (Mn) ions. It introduces an innovative approach using graphene oxide (GO) and GO-decorated polyethersulphone (PES) membranes to efficiently remove these ions from contaminated water. The process involves integrating GO into PES membranes to enhance their adsorption capacity. Characterization techniques, including scanning electron microscopy, Fourier-transform infrared, and contact angle measurements, were used to assess structural and surface properties. The modified membranes demonstrated significantly improved adsorption compared to pristine PES. Notably, they achieved over 94% removal of Mn2+ and 93.6% of Fe2+ in the first filtration cycle for water with an initial concentration of 100 ppm. Continuous filtration for up to five cycles maintained removal rates above 60%. This research advances water purification materials, offering a promising solution for heavy metal ion removal. GO-decorated PES membranes may find application in large-scale water treatment, addressing environmental and public health concerns.

Recent advances in chitosan-based nanocomposites for adsorption and removal of heavy metal ions.

Due to the high concentration of various toxic and dangerous pollutants, industrial effluents have imposed increasing threats. Among the various processes for wastewater treatment, adsorption is widely used due to its simplicity, good treatment efficiency, availability of a wide range of adsorbents, and cost-effectiveness. Chitosan (CS) has received great attention as a pollutant adsorbent due to its low cost and many -OH and -NH2 functional groups that can bind heavy metal ions. However, weaknesses such as sensitivity to pH, low thermal stability and low mechanical strength, limit the application of CS in wastewater treatment. The modification of these functional groups can improve its performance via cross-linking and grafting agents. The porosity and specific surface area of CS in powder form are not ideal, so physical modification of CS via integration with other materials (e.g., metal oxide, zeolite, clay, etc.) leads to the creation of composite materials with improved absorption performance. This review provides reports on the application of CS and its nanocomposites (NCs) for the removal of various heavy metal ions. Synthesis strategy, adsorption mechanism and influencing factors on sorbents for heavy metals are discussed in detail.

Research progress in the detection of trace heavy metal ions in food samples.

Food safety is the basis for ensuring human survival and development. The threat of heavy metal ions to food safety has become a social concern with the rapid growth of the economy and the accompanying environmental pollution. Some heavy metal ions are highly toxic even at trace levels and pose significant health risks to humans. Therefore, ultrasensitive detection of heavy metal ions in food samples is important. In this mini-review, recent advances in the analytical methods based on nanomaterials for detecting trace heavy metal ions in food samples are summarized in three categories: electrochemical, colorimetric, and fluorescent methods. We present the features and sensing mechanisms of these three methods, along with typical examples to illustrate their application in the detection of heavy metal ions in foods. This mini-review ends with a discussion of current challenges and future prospects of these approaches for sensing heavy metal ions. The review will help readers understand the principles of these methods, thereby promoting the development of new analytical methods for the detection of heavy metal ions in food samples.

Recent advances in alginate-based composite gel spheres for removal of heavy metals.

The discharge of heavy metal ions from industrial wastewater into natural water bodies is a consequence of global industrialisation. Due to their high toxicity and resistance to degradation, these heavy metal ions pose a substantial threat to human health as they accumulate and amplify. Alginate-based composite gels exhibit good adsorption and mechanical properties, excellent biodegradability, and non-toxicity, making them environmentally friendly heavy metal ion adsorbents for water with promising development prospects. This paper introduces the basic properties, cross-linking methods, synthetic approaches, modification methods, and manufacturing techniques of alginate-based composite gels. The adsorption properties and mechanical strength of these gels can be enhanced through surface modification, multi-component mixing, and embedding. The main production processes involved are sol-gel and cross-linking methods. Additionally, this paper reviews various applications of alginate composite gels for common heavy metals, rare earth elements, and radionuclides and elucidates the adsorption mechanism of alginate composite gels. This study aimed to provide a reference for synthesising new, efficient, and environmentally friendly alginate-based adsorbents and to contribute new ideas and directions for addressing the issue of heavy metal pollution.

Highly stable mesoporous Co/Ni mixed metal-organic framework [Co/Ni(µ3-tp)2(µ2-pyz)2] for Co (II) heavy metal ions (HMIs) remediation.

A bimetallic cobalt/nickel-based metal-organic framework (MOF), [Co/Ni(µ3-tp)2(µ2-pyz)2], denoted as Co/Ni-MOF, has been successfully prepared by a hydrothermal method. The MOF was prepared by incorporating mixed O- and N- donor ligands, specifically terephthalic acid (tp) and pyrazine (pyz). The Mesoporous Co/Ni-MOF was comprehensively characterized using various analytical methods such as XRD, BET, FT-IR, TGA (23 % char yields), SEM, and EDS analyses. The synthesized mesoporous Co/Ni-MOF was then used to absorb Co (II) from aquatic areas efficiently. Several critical parameters, such as the beginning Co (II) concentration (25-150 mg/L), the effect of pH (2-10), the duration of time (5-30 min), and the amount of adsorbent (0.003-0.02 g), were systematically investigated. Remarkably, the Mesoporous Co/Ni MOF displayed a significant adsorption capacity of 372.66 mg g-1 in the optimum conditions, including pH = 6, amount of adsorbent = 0.003 g, duration of time = 25 min, and beginning Co (II) concentration = 150 mg/L. Adsorption data from the experimental studies of the mesoporous Co/Ni MOF are matched based on the non-linear pseudo-first-order (PSO) kinetic model (R2 = 0.9999), and a chemical process is suggested for chemisorption. Furthermore, the adsorption isotherms of Co (II) heavy metal ions (HMIs) are an excellent fit with the non-linear Temkin, indicating that they explain the sorbent/sorbate interactions concerning the heat of adsorption. It is evident from the thermodynamic parameters that adsorption is a spontaneous and favorable exothermic process. These results highlight the promising adsorption performance and potential applications of the mesoporous Co/Ni-MOF as an effective adsorbent for Co (II) elimination from aquatic areas. Four-cycle regeneration studies were the most effective for the Co (II) under study.