Synthesis of Cs3Cu2I5 Nanocrystals in a Continuous Flow System.

Achieving the goal of generating all of the world's energy via renewable sources and significantly reducing the energy usage will require the development of novel, abundant, nontoxic energy conversion materials. Here, a cost-efficient and scalable continuous flow synthesis of Cs3Cu2I5 nanocrystals is developed as a basis for the rapid advancement of novel nanomaterials. Ideal precursor solutions are obtained through a novel batch synthesis, whose product served as a benchmark for the subsequent flow synthesis. Realizing this setup enabled a reproducible fabrication of Cs3Cu2I5 nanocrystals. The effect of volumetric flow rate and temperature on the final product's morphology and optical properties are determined, obtaining 21% quantum yield with the optimal configuration. Consequently, the size and morphology of the nanocrystals can be tuned with far more precision and in a much broader range than previously achievable. The flow setup is readily applicable to other relevant nanomaterials. It should enable a rapid determination of a material's potential and subsequently optimize its desired properties for renewable energy generation or efficient optoelectronics.

Balancing Flexible Side Chains on 2D Conjugated Acceptors Enables High-Performance Organic Solar Cell.

Balancing the rigid backbones and flexible side chains of light-harvesting materials is crucially important to reach optimized intermolecular packing, micromorphology, and thus photovoltaic performance of organic solar cells (OSCs). Herein, based on a distinctive CH-series acceptor platform with 2D conjugation extended backbones, a series of nonfullerene acceptors (CH-6F-Cn) are synthesized by delicately tuning the lengths of flexible side chains from n-octyl to n-amyl. A systemic investigation has revealed that the variation of the side chain's length can not only modulate intermolecular packing modes and crystallinity but also dramatically improve the micromorphology of the active layer and eventual photovoltaic parameters of OSCs. Consequently, the highest PCE of 18.73% can be achieved by OSCs employing D18:PM6:CH-6F-C8 as light-harvesting materials.

Application of the Electrospinning Technique in Electrochemical Biosensors: An Overview.

Electrospinning is a cost-effective and flexible technology for producing nanofibers with large specific surface areas, functionalized surfaces, and stable structures. In recent years, electrospun nanofibers have attracted more and more attention in electrochemical biosensors due to their excellent morphological and structural properties. This review outlines the principle of electrospinning technology. The strategies of producing nanofibers with different diameters, morphologies, and structures are discussed to understand the regulation rules of nanofiber morphology and structure. The application of electrospun nanofibers in electrochemical biosensors is reviewed in detail. In addition, we look towards the future prospects of electrospinning technology and the challenge of scale production.

Layer-by-Layer-Processed All-Polymer Solar Cells with Enhanced Performance Enabled by Regulating the Microstructure of Upper Layer.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, the polymers D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the cells' crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via the LBL fabrication method in regulating the microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

Layer-by-Layer Organic Solar Cells Enabled by 1,3,4-Selenadiazole-Containing Crystalline Small Molecule with Double-Fibril Network Morphology.

A double-fibril network of the photoactive layer morphology is recognized as an ideal structure facilitating exciton diffusion and charge carrier transport for high-performance organic solar cells (OSCs). However, in the layer-by-layer processed OSCs (LbL-OSCs), polymer donors and small molecule acceptors (SMAs) are separately deposited, and it is challenging to realize a fibril network of pure SMAs with the absence of tight interchain entanglement as polymers. In this work, crystalline small molecule donors (SMDs), named TDZ-3TR and SeDZ-3TR, were designed and introduced into the L8-BO acceptor solution, forcing the phase separation and molecular fibrilization. SeDZ-3TR showed higher crystallinity and lower miscibility with L8-BO acceptor than TDZ-3TR, enabling more driving force to favor the phase separation and better molecular fibrilization of L8-BO. On the other hand, two donor polymers of PM6 and D18 with different fibril widths and lengths were put together to optimize the fibril network of the donor layer. The simultaneously optimization of the acceptor and donor layers resulted in a more ideal double-fibril network of the photoactive layer and an impressive power conversion efficiency (PCE) of 19.38 % in LbL-OSCs.

Rare Earth Doping Engineering Tailoring Advanced Oxygen-Vacancy Co3 O4 with Tunable Structures for High-Efficiency Energy Storage.

Co3 O4  with high theoretical capacitance is a promising electrode material for high-end energy applications, yet the unexcited bulk electrochemical activity, low conductivity, and poor kinetics of Co3 O4  lead to unsatisfactory charge storage capacity. For boosting its energy storage capability, rare earth (RE)-doped Co3 O4  nanostructures with abundant oxygen vacancies are constructed by simple, economical, and universal chemical precipitation. By changing different types of RE (RE = La, Yb, Y, Ce, Er, Ho, Nd, Eu) as dopants, the RE-doped Co3 O4  nanostructures can be well transformed from large nanosheets to coiled tiny nanosheets and finally to ultrafine nanoparticles, meanwhile, their specific surface area, pore distribution, the ratio of Co2+ /Co3+ , oxygen vacancy content, crystalline phase, microstrain parameter, and the capacitance performance are regularly affected. Notably, Eu-doped Co3 O4  nanoparticles with good cycle stability show a maximum specific capacitance of 1021.3 F g-1 (90.78 mAh g-1 ) at 2 A g-1 , higher than 388 F g-1 (34.49 mAh g-1 ) of pristine Co3 O4  nanosheets. The assembling asymmetric supercapacitor delivers a high energy density of 48.23 Wh kg-1  at high power density of 1.2 kW kg-1 . These findings denote the significance and great potential of RE-doped Co3 O4  in the development of high-efficiency energy storage.

Meniscus-Guided Deposition of Organic Semiconductor Thin Films: Materials, Mechanism, and Application in Organic Field-Effect Transistors.

Solution-processable organic semiconductors are one of the promising materials for the next generation of organic electronic products, which call for high-performance materials and mature processing technologies. Among many solution processing methods, meniscus-guided coating (MGC) techniques have the advantages of large-area, low-cost, adjustable film aggregation, and good compatibility with the roll-to-roll process, showing good research results in the preparation of high-performance organic field-effect transistors. In this review, the types of MGC techniques are first listed and the relevant mechanisms (wetting mechanism, fluid mechanism, and deposition mechanism) are introduced. The MGC processes are focused and the effect of the key coating parameters on the thin film morphology and performance with examples is illustrated. Then, the performance of transistors based on small molecule semiconductors and polymer semiconductor thin films prepared by various MGC techniques is summarized. In the third section, various recent thin film morphology control strategies combined with the MGCs are introduced. Finally, the advanced progress of large-area transistor arrays and the challenges for roll-to-roll processes are presented using MGCs. Nowadays, the application of MGCs is still in the exploration stage, its mechanism is still unclear, and the precise control of film deposition still needs experience accumulation.

Enhancing Resistance to Chloride Corrosion by Controlling the Morphologies of PtNi Electrocatalysts for Alkaline Seawater Hydrogen Evolution.

A solvothermal method to prepare PtNi alloys that have differing morphologies is described. By adjusting the feed ratio of Pt and Ni precursors in this process, PtNi alloys with different compositions (Pt : Ni atomic ratio from 1 : 3 to 3 : 1) and morphologies (evolution from nanobranches to nanoparticles) are generated. The prepared Pt48 Ni52 alloy, which has a composite morphology comprised of nanobranches and nanoparticles, exhibits superior activity and durability towards the hydrogen evolution reaction (HER) in seawater compared to those of commercial Pt/C catalyst and other PtNi alloys that have different compositions and morphologies. The excellent seawater HER performance of Pt48 Ni52 is ascribed to its nanobranch/nanoparticle morphology that optimally facilitates electron accumulation on Pt, which enhances resistance to chloride corrosion in seawater.

Green synthesis of rectangular hollow tubular carbon nitride via in-situ self-assembly strategy to enhance the degradation of tetracycline hydrochloride under visible light irradiation.

It has been an urgent requirement for materials with remarkable performance in the photocatalytic degradation of organic contaminants by photocatalytic technology. Limited surface area and speedy recombination rate of photogenerated charge carriers seriously restrain the application of g-C3N4. Morphology control is a powerful approach to enhance the photocatalytic efficiency of g-C3N4. Herein, we reported a method to attain graphitic carbon nitride with rectangular hollow tubular morphology and asperous surface (TUM-CN-2) which is prepared from urea-melamine hydrothermal products and trithiocyanuric acid by self-assembling without using organic solvents or template agents. The specific surface area, photocatalytic activity, and photo-generated carriers migration and separation rate of the obtained photocatalyst TUM-CN-2 are vastly improved. Contrasted with pure g-C3N4, the degradation rate of tetracycline hydrochloride (TCH) and Rhodamine B (RhB) was enhanced about 3.04 and 13.96 times in visible light irradiation, respectively. Moreover, the interference parameters, active free radicals, potential degradation mechanism, and degradation paths of TCH were researched systematically. This work provides a green way to acquire the modified g-C3N4 with splendid catalytic activity through the self-assembly method.

Solvent-Controlled Morphology of Zinc-Cobalt Bimetallic Sulfides for Supercapacitors.

Bimetallic sulfides offer high theoretical specific capacitance and good stability as electrode materials due to their diverse redox reactions, larger specific surface areas, and better conductivity. The morphology of the electrode material is an important influencing factor for the electrochemical properties. Herein, a series of ZnCoS electrode materials with different morphologies were prepared by varying the solvent in the solvothermal reaction, and the effects of different microstructures on the electrochemical properties of ZnCoS were investigated. The ratio of water and ethanol in the solvent was controlled to modulate the microstructure of the as-prepared ZnCoS materials. XRD and XPS revealed the physical and chemical structure of the ZnCoS materials. SEM and TEM observations showed that the microstructure of ZnCoS transformed from one-dimensional wires to two-dimensional sheets with increasing amounts of ethanol. The maximum specific capacitance of the as-prepared ZnCoS materials is 6.22 F cm-2 at a current density of 5 mA cm-2, which is superior to that of most previously reported bimetallic sulfides. The enhanced electrochemical performance could be ascribed to its sheet-assembled spherical structure, which not only shortens the path of ion diffusion but also increases the contact between surface active sites and the electrolyte. Moreover, the spherical structure provides numerous void spaces for buffering the volume expansion and penetration of the electrolyte, which would be favorable for electrochemical reactions. Furthermore, the ZnCoS electrodes were coupled with activated carbon (AC) electrodes to build asymmetric supercapacitors (ASCs). The ASC device exhibits a maximum energy density of 0.124 mWh cm-2 under a power density of 2.1 mW cm-2. Moreover, even under a high-power density of 21 mW cm-2, the energy density can still reach 0.055 mWh cm-2.

Influence of Co3O4 Nanostructure Morphology on the Catalytic Degradation of p-Nitrophenol.

The design and fabrication of nanomaterials with controllable morphology and size is of critical importance to achieve excellent catalytic performance in heterogeneous catalysis. In this work, cobalt oxide (Co3O4) nanostructures with different morphologies (nanoplates, microflowers, nanorods and nanocubes) were successfully constructed in order to establish the morphology-property-performance relationship of the catalysts. The morphology and structure of the nanostructured Co3O4 were characterized by various techniques, and the catalytic performance of the as-prepared nanostructures was studied by monitoring the reduction of p-nitrophenol to p-aminophenol in the presence of excess NaBH4. The catalytic performance was found to be strongly dependent on their morphologies. The experimental results show that the pseudo-first-order reaction rate constants for Co3O4 nanostructures with various shapes are, respectively, 1.49 min-1 (nanoplates), 1.40 min-1 (microflowers), 0.78 min-1 (nanorods) and 0.23 min-1 (nanocubes). The Co3O4 nanoplates exhibited the highest catalytic activity among the four nanostructures, due to their largest specific surface area, relatively high total pore volume, best redox properties and abundance of defect sites. The established correlation between morphology, property and catalytic performance in this work will offer valuable insight into the design and application of nanostructured Co3O4 as a potential non-noble metal catalyst for p-nitrophenol reduction.

Recent Progress in Photocatalytic Degradation of Water Pollution by Bismuth Tungstate.

Photocatalysis has emerged as a highly promising, green, and efficient technology for degrading pollutants in wastewater. Among the various photocatalysts, Bismuth tungstate (Bi2WO6) has gained significant attention in the research community due to its potential in environmental remediation and photocatalytic energy conversion. However, the limited light absorption ability and rapid recombination of photogenerated carriers hinder the further improvement of Bi2WO6's photocatalytic performance. This review aims to present recent advancements in the development of Bi2WO6-based photocatalysts. It delves into the photocatalytic mechanism of Bi2WO6 and summarizes the achieved photocatalytic characteristics by controlling its morphology, employing metal and non-metal doping, constructing semiconductor heterojunctions, and implementing defective engineering. Additionally, this review explores the practical applications of these modified Bi2WO6 photocatalysts in wastewater purification. Furthermore, this review addresses existing challenges and suggests prospects for the development of efficient Bi2WO6 photocatalysts. It is hoped that this comprehensive review will serve as a valuable reference and guide for researchers seeking to advance the field of Bi2WO6 photocatalysis.

Engineered Aptamer-Organic Amphiphile Self-Assemblies for Biomedical Applications: Progress and Challenges.

Currently, nucleic acid aptamers are exploited as robust targeting ligands in the biomedical field, due to their specific molecular recognition, little immunogenicity, low cost, ect. Thanks to the facile chemical modification and high hydrophilicity, aptamers can be site-specifically linked with hydrophobic moieties to prepare aptamer-organic amphiphiles (AOAs), which spontaneously assemble into aptamer-organic amphiphile self-assemblies (AOASs). These polyvalent self-assemblies feature with enhanced target-binding ability, increased resistance to nuclease, and efficient cargo-loading, making them powerful platforms for bioapplications, including targeted drug delivery, cell-based cancer therapy, biosensing, and bioimaging. Besides, the morphology of AOASs can be elaborately manipulated for smarter biomedical functions, by regulating the hydrophilicity/hydrophobicity ratio of AOAs. Benefiting from the boom in DNA synthesis technology and nanotechnology, various types of AOASs, including aptamer-polymer amphiphile self-assemblies, aptamer-lipid amphiphile self-assemblies, aptamer-cell self-assemblies, ect, have been constructed with great biomedical potential. Particularly, stimuli-responsive AOASs with transformable structure can realize site-specific drug release, enhanced tumor penetration, and specific target molecule detection. Herein, the general synthesis methods of oligonucleotide-organic amphiphiles are firstly summarized. Then recent progress in different types of AOASs for bioapplications and strategies for morphology control are systematically reviewed. The present challenges and future perspectives of this field are also discussed.

Metallopolymer Particle Engineering via Etching of Boronate Polymers toward High-Performance Overall Water Splitting Catalysts.

Metallopolymers combine the property features of both metallic compounds and organic polymers, representing a typical direction for the design of high-performance hybrid materials. Here, a highly adaptive etching method to create pores and cavities in the metallopolymer particles is established. Starting from boronate polymer (BP) and inorganic@BP core-shell particles, porous, hollow, and yolk-shell metallopolymer particles can be fabricated, respectively. By taking advantage of the easy control over composition and pore/cavity structure, these metallopolymer particles provide a universal platform for the fabrication of nitrogen, boron co-doped carbon nanocomposites loaded with metals (M-NBCs). The as-prepared M-NBCs exhibit remarkable catalytic activities toward oxygen evolution reaction and hydrogen evolution reaction. An alkaline overall water splitting cell assembled by using M-NBCs as the anode and cathode can be driven by a single AAA battery. The proposed strategy for the construction of metallopolymer composites may enlighten for the design of complex hybrid nanomaterials.

Biomimetic DNA Nanotechnology to Understand and Control Cellular Responses.

At the cellular level, numerous nanocues guide the cells to adhere, interact, proliferate, differentiate, etc. Understanding and manipulating the cellular functions in vitro, necessitates the elucidation of these nanocues provided to the cells by the extracellular matrix (ECM), neighbouring cells or in the form of ligands. DNA nanotechnology is a biocompatible, flexible and a promising molecular level toolkit for mimicking cell-cell and cell-matrix interactions. In this review, we summarize various advances in cell-matrix, cell-cell and cell receptor-ligand interactions using DNA nanotechnology as a tool. We also provide a brief outlook on the current challenges and the future potentials of these DNA-based nanostructures so as to inspire novel innovations in the field.

Modulated Synthesis of Self-Standing Covalent Organic Framework Films.

The weak interaction of covalent organic framework (COF) nanoparticles makes the preparation of self-standing COF films difficult. Herein, a modulated strategy for the facile synthesis of self-standing COF films with good crystallinity and tunable thickness is reported. As compared with the non-modulated approach, the modulated strategy changes the COF morphology from nanoparticles to nanofibers, enabling the facile preparation of self-standing COF films with improved mechanical properties. The Young's modulus of the self-standing COF film obtained via the modulated strategy could increase by 26 times. Moreover, self-standing LZU-8 film can be used as a membrane for efficient removal of 99 % mercury ions from aqueous solution. Our results open up a new approach to prepare self-standing COF thin films for practical applications.

Synthesis of Lead-Free Cs2AgBiX6 (X = Cl, Br, I) Double Perovskite Nanoplatelets and Their Application in CO2 Photocatalytic Reduction.

Morphology control represents an important strategy for the development of functional nanomaterials and has yet to be achieved in the case of promising lead-free double perovskite materials so far. In this work, high-quality Cs2AgBiX6 (X = Cl, Br, I) two-dimensional nanoplatelets were synthesized through a newly developed synthetic procedure. By analyzing the optical, morphological, and structural evolutions of the samples during synthesis, we elucidated that the growth mechanism of lead-free double perovskite nanoplatelets followed a lateral growth process from mono-octahedral-layer (half-unit-cell in thickness) cluster-based nanosheets to multilayer (three to four unit cells in thickness) nanoplatelets. Furthermore, we demonstrated that Cs2AgBiBr6 nanoplatelets possess a better performance in photocatalytic CO2 reduction compared with their nanocube counterpart. Our work demonstrates the first example with two-dimensional morphology of this important class of lead-free perovskite materials, shedding light on the synthetic manipulation and the application integration of such promising materials.

Synergy Effect of High-Stability of VS4 Nanorods for Sodium Ion Battery.

Sodium-ion batteries (SIBs) have attracted increasing interest as promising candidates for large-scale energy storage due to their low cost, natural abundance and similar chemical intercalation mechanism with lithium-ion batteries. However, achieving superior rate capability and long-life for SIBs remains a major challenge owing to the limitation of favorable anode materials selection. Herein, an elegant one-step solvothermal method was used to synthesize VS4 nanorods and VS4 nanorods/reduced graphene oxide (RGO) nanocomposites. The effects of ethylene carbonate/diethyl carbonate(EC/DEC), ethylene carbonate/dimethyl carbonate(EC/DMC), and tetraethylene glycol dimethyl ether (TEGDME) electrolytes on the electrochemical properties of VS4 nanorods were investigated. The VS4 nanorods electrodes exhibit high specific capacity in EC/DMC electrolytes. A theoretical calculation confirms the advance of EC/DMC electrolytes for VS4 nanorods. Significantly, the discharge capacity of VS4/RGO nanocomposites remains 100 mAh/g after 2000 cycles at a large current density of 2 A/g, indicating their excellent cycling stability. The nanocomposites can improve the electronic conductivity and reduce the Na+ diffusion energy barrier, thereby effectively improving the sodium storage performance of the hybrid material. This work offers great potential for exploring promising anode materials for electrochemical applications.

Sequential Passivation for Lead-Free Tin Perovskite Solar Cells with High Efficiency.

Lead-free tin perovskite solar cells (PKSCs) have attracted tremendous interest as a replacement for toxic lead-based PKSCs. Nevertheless, the efficiency is significantly low due to the rough surface morphology and high number of defects, which are caused by the fast crystallization and easy oxidization. In this study, a facile and universal posttreatment strategy of sequential passivation with acetylacetone (ACAC) and ethylenediamine (EDA) is proposed. The results show that ACAC can reduce the trap density and enlarge the grain size (short-circuit current (Jsc ) enhancement), while EDA can bond the undercoordinated tin and regulate the energy level (open-circuit voltage (Voc ) enhancement). A promising 13 % efficiency is achieved with better stability. In addition, other combinations of diketones or amines are selected, with similar effects. This study provides a universal strategy to enhance the crystallinity and passivate defects while fabricating stable PKSCs with high efficiency.

Single-Step Expeditious Synthesis of Diblock Copolymers with Different Morphologies by Lewis Pair Polymerization-Induced Self-Assembly.

Lewis pair polymerization has demonstrated its unique advantages and powerful capability in polymer synthesis. Here we employ strong nucleophilic N-heterocyclic olefin (NHO) and bulky organoaluminum to construct a frustrated Lewis pair, which can realize the compounded sequence control (CSC) copolymerization and self-assembly the mixture of dimethylaminoethyl acrylate and fluoride-functionalized methacrylate into diblock copolymers (di-BCPs) nano-assemblies through polymerization-induced self-assembly in one-pot, single-step manner within minutes. These di-BCPs were characterized by 1 H and 13 C NMR, GPC, DSC, and TEM. By utilizing appropriate solvophilic block and solvophobic block, such Lewis pair polymerization-induced self-assembly strategy enables the expeditious, room-temperature synthesis of di-BCP nanoparticles with different morphologies, including spheres, worms, vesicles, and even fibers, thus suggesting the great application potential of such method in the future.