Measurement of Soot Concentration in Burner Diffusion Flames through Emission Spectroscopy with Particle Swarm Optimization.

Measuring soot concentration in a burner flame is essential for an in-depth understanding of the formation mechanism and to abate its generation. This paper presents an improved emission spectroscopy (ES) method that uses an adaptive particle swarm optimization (APSO) algorithm for measuring the concentration of soot in methane burner flames. Experimental tests were conducted on a laboratory-scale facility under a methane flowrate ranging between 0.6 and 0.9 L/min. A comparison analysis of the soot concentration measured by the ES method, the improved emission spectroscopy (IES) method, and the thermocouple particle density (TPD) method (as a reference) was conducted. The ES method obtained a maximum absolute deviation of 0.84 ppm from the average soot concentration at the three measurement points compared to the TPD method, while that of the IES was only 0.09 ppm. The experimental results demonstrate that the proposed IES method can obtain a more accurate soot concentration of diffusion flames.

Mechanistic Observation of Interactions between Macrophages and Inorganic Particles with Different Densities.

Many different types of inorganic materials are processed into nano/microparticles for medical utilization. The impact of selected key characteristics of these particles, including size, shape, and surface chemistries, on biological systems, is frequently studied in clinical contexts. However, one of the most important basic characteristics of these particles, their density, is yet to be investigated. When the particles are designed for drug delivery, highly mobile macrophages are the major participants in cellular levels that process them in vivo. As such, it is essential to understand the impact of particles' densities on the mobility of macrophages. Here, inorganic particles with different densities are applied, and their interactions with macrophages studied. A set of these particles are incubated with the macrophages and the outcomes are explored by optical microscopy. This microscopic view provides the understanding of the mechanistic interactions between particles of different densities and macrophages to conclude that the particles' density can affect the migratory behaviors of macrophages: the higher the density of particles engulfed inside the macrophages, the less mobile the macrophages become. This work is a strong reminder that the density of particles cannot be neglected when they are designed to be utilized in biological applications.

Densely Packed, Ultra Small SnO Nanoparticles for Enhanced Activity and Selectivity in Electrochemical CO2 Reduction.

Controlling the selectivity in electrochemical CO2 reduction is an unsolved challenge. While tin (Sn) has emerged as a promising non-precious catalyst for CO2 electroreduction, most Sn-based catalysts produce formate as the major product, which is less desirable than CO in terms of separation and further use. Tin monoxide (SnO) nanoparticles supported on carbon black were synthesized and assembled and their application in CO2 reduction was studied. Remarkably high selectivity and partial current densities for CO formation were obtained using these SnO nanoparticles compared to other Sn catalysts. The high activity is attributed to the ultra-small size of the nanoparticles (2.6 nm), while the high selectivity is attributed to a local pH effect arising from the dense packing of nanoparticles in the conductive carbon black matrix.

Association of novel metrics of particulate matter with vascular markers of inflammation and coagulation in susceptible populations -results from a panel study.

BACKGROUND AND AIMS: Epidemiological studies have shown adverse effects of ambient air pollutants on health with inflammation and oxidative stress playing an important role. We examine the association between blood biomarkers of inflammation and coagulation and physical attributes of particulate matter which are not routinely measured such as particle length or surface area concentration and apparent density of PM. METHODS: Between 3/2007 and 12/2008 187 non-smoking individuals with type 2 diabetes mellitus (T2D) or impaired glucose tolerance (IGT) were examined within the framework of the KORA Study in Augsburg, Germany. In addition, we selected 87 participants with a potential genetic predisposition on detoxifying and inflammatory pathways. This was defined by the null polymorphism for glutathione S-transferase M1 in combination with a certain single nucleotide polymorphism on the C-reactive protein (CRP) gene (rs1205) or the fibrinogen gene (rs1800790). Participants had blood drawn up to seven different times, resulting in 1765 blood samples. Air pollutants were collected at a central measurement station and individual 24-h averages calculated. Associations between air pollutants and high sensitivity CRP, myeloperoxidase (MPO), interleukin (IL)-6 and fibrinogen were analysed using additive mixed models. RESULTS: For the panel with genetic susceptibility, increases were seen for CRP and MPO with most attributes, specifically particle length and active surface concentration. The %change of geometric mean and 95% confidence intervals for the 5-day average exposure for CRP and MPO were 34.6% [21.8;48.8] and 8.3% [3.2;13.6] per interquartile range increase of particle length concentration and 29.8% [15.9;45.3] and 10.4 [4.4;16.7] for active surface area. Results for the panel of T2D and IGT and the other blood biomarkers were less conclusive. CONCLUSIONS: Particle length concentration and active surface concentration showed strong positive associations with blood biomarkers reflecting inflammation. These air pollution metrics might reflect harmful aerosol properties better than particulate mass or number concentration. They might therefore be important for epidemiological studies.

Size- and concentration-dependent effects of microplastics on soil aggregate formation and properties.

Plastics fragment and threaten soil ecosystems. Degradation of soil structure is one of the risks. Despite this, data on impacts of different sized microplastics (MPs) on soil aggregates is lacking. This study systematically investigated the effects of pristine polyethylene powders of different sizes (< 35, < 125, < 500 µm) and concentrations (0, 0.1, 1.0, 10 wt%) on aggregate formation and their properties for two contrasting soils (woodland soil, WS; agricultural soil, AS). 75 day wet-dry cycles produced newly-formed aggregates in all treatments. MP size and concentration impacted the incorporation of MPs in aggregates and this varied with aggregate size; the size distribution of aggregates also varied with MP size and concentration. Aggregates produced in soil containing 10 wt% < 35 µm MPs had significantly lower MWDs (mean weight diameters) than controls. The wettability of aggregates (> 4 mm) reduced with increasing MP exposure concentration and decreasing MP exposure size. MP incorporation decreased the water stability of aggregates (1-2 mm) in WS but increased it in AS. The particle density of aggregates (> 4 mm) significantly decreased with increasing MP concentration, whereas MP size had no effect. As MPs breakdown, fragment and become smaller over time, their potential risk to the aggregated structure of soil increases.

Biodrying of municipal solid waste-correlations between moisture content, organic content, and end of the biodrying process time.

Biodrying refers to the decomposition of organic municipal solid waste (MSW) under aerobic conditions. This process usually lasts 14 days and requires large amounts of air to be injected into the waste matrix. The efficiency of the biodrying process depends on several geotechnical parameters, including initial moisture content, initial organic content, bulk density, dry density, solid particle density, and porosity. To examine the potential influence of these parameters on the biodrying process, we analyzed 13 biodried MSW samples. The results revealed a strong positive linear relationship between the initial moisture content and the mass loss percentage. In the first three days of the biodrying process, the waste mass rapidly decreased; afterwards, the daily mass loss occurred at a less rapid, more constant rate. The established average mass removal ratio between the volatile solids and water was 1:6.38 with a standard deviation of 1.06. Dry and solid particle densities were preserved in all 13 experiments; thus, the corresponding void ratio remained unchanged. This finding suggests that the settlement and degradation of MSW that occur during the biodrying process did not significantly influence the airflow rate.

Evaluation of alternative methods to derive particle density from compression data.

The determination of particle density is a critical part of material characterization regarding compression analyses. Helium pycnometry as the most commonly used method is criticized for different aspects. Most prominent is the susceptibility to errors when measuring water-containing powders. Alternative methods for determining particle density using compression data have already been described. However, a systematic investigation and evaluation is still missing. In this study, the methods by Sun and Krumme were investigated in detail regarding their robustness against variations in tableting settings. Twelve pharmaceutical excipients were tableted at five different settings to verify the applicability and sensitivity to changes in the experimental set-up. Both methods were found to be robust against influencing parameters from the experiments. A sufficiently high compression pressure to approach a constant density value of the corresponding material during tableting was considered to be an essential requirement for the performance of the methods. Brittle materials with high yield pressure were found to be unsuitable for the application of both methods. The method of Krumme gave small deviations to measurements of helium pycnometry for water-free materials. By using the tablet density after in-die elastic recovery, Krumme's method could be used for water-containing materials as well. The method of Sun was found to give significantly smaller values for particle density due to inclusion of slow elastic recovery.

Generating a Sustained Oxygen-Stable Atomic Concentration in a High-Temperature Gas Effect Investigation.

Modulated laser absorption spectroscopy is an ideal technique for evaluating flow-field parameters and determining flow-field quality by measuring the atoms dissociated in high-temperature environments. However, to obtain the absolute number density of atoms in the flow field, it is necessary to compare the measured modulated absorption spectroscopy signal with a known atomic concentration and establish a quantitative relationship through concentration calibration. Nevertheless, it remains a challenging task to prepare transient atomic samples with known concentrations that meet the calibration requirements. This study utilized the alternating-current glow discharge technique to dissociate oxygen in the air flow, resulting in the continuous generation of oxygen atoms. The absolute number densities of the generated oxygen atoms were determined by measuring the direct absorption spectra of centered on 777 nm for oxygen atoms. The number densities of the generated atoms were finely tuned by adjusting the discharge parameters. Throughout the 120-min continuous operation of the discharge system, the concentration of excited-state oxygen atoms remained stable within the range of (2.51 ± 0.02) × 108 cm-3, demonstrating the remarkable stability of the transient atomic concentration generated by the glow discharge plasma. This observation suggests that the generated atoms can be utilized as a standardized atomic sample of known concentration for absolute concentration calibration purposes.

Sample Size Effects on Petrophysical Characterization and Fluid-to-Pore Accessibility of Natural Rocks.

Laboratory-scale analysis of natural rocks provides petrophysical properties such as density, porosity, pore diameter/pore-throat diameter distribution, and fluid accessibility, in addition to the size and shape of framework grains and their contact relationship with the rock matrix. Different types of laboratory approaches for petrophysical characterization involve the use of a range of sample sizes. While the sample sizes selected should aim to be representative of the rock body, there are inherent limitations imposed by the analytical principles and holding capacities of the different experimental apparatuses, with many instruments only able to accept samples at the µm-mm scale. Therefore, a total of nine (three limestones, three shales, two sandstones, and one dolomite) samples were collected from Texas to fill the knowledge gap of the sample size effect on the resultant petrophysical characteristics. The sample sizes ranged from 3 cm cubes to <75 µm particles. Using a combination of petrographic microscopy, helium expansion pycnometry, water immersion porosimetry, mercury intrusion porosimetry, and (ultra-) small-angle X-ray scattering, the impact of sample size on the petrophysical properties of these samples was systematically investigated here. The results suggest that the sample size effect is influenced by both pore structure changes during crushing and sample size-dependent fluid-to-pore connectivity.

Determination of physical properties of undisturbed soil samples according to V. Novák.

The methodology described here presents the procedures for determining physical soil properties of undisturbed soil samples. Besides describing the methods for determining bulk and particle density, moisture content and porosity of the soil in detail, it also offers a way of determining soil's water holding properties when there is no pressure membrane apparatus available. This method is based on a capillary water saturation experiment and gravimetric measurements performed in different time intervals after the saturation (30 minutes, 2 hours, and 24 hours). With a few, simple to follow steps, and not using complicated and space-consuming equipment, it can be replicated in almost any laboratory, and the results are easily interpreted. The method was, and still is, widely used in the Czech Republic, and some parts of it are used as standard soil testing methods. To a lesser or greater detail, this method is described in Rejsek (1999), Valla et al. (2011), Pospísilová et al. (2016) and ÚKZÚZ (2016), and this methodology is compiled from those publications, mainly focusing (and using the same abbreviations) on the procedures described by Valla et al. (2011). The methodology described does not essentially differ from the original, but the steps here have been described to a greater detail, based on the practical experiences obtained over the years, in order to make some common mistakes less likely to happen. The methodology is further complemented with graphical illustrations for each step described in the process, making it clearer, more easily understood, and easier to replicate. Since this methodology has not been available in English so far, this guide offers a great opportunity of its replication on an international level.•Simple, cost-effective and environmentally friendly method for determining physical soil properties•Easy replication and results interpretation•Results can be obtained even in non-highly specialized soil laboratories.

Measuring TiO2N and AgHEC Airborne Particle Density during a Spray Coating Process.

Effective particle density is a key parameter for assessing inhalation exposure of engineered NPs in occupational environments. In this paper, particle density measurements were carried out using two different techniques: one based on the ratio between mass and volumetric particle concentrations; the other one based on the ratio between aerodynamic and geometric particle diameter. These different approaches were applied to both field- and laboratory-scale atomization processes where the two target NPs (N-doped TiO2, TiO2N and AgNPs capped with a quaternized hydroxyethylcellulose, AgHEC) were generated. Spray tests using TiO2N were observed to release more and bigger particles than tests with AgHEC, as indicated by the measured particle mass concentrations and volumes. Our findings give an effective density of TiO2N particle to be in a similar range between field and laboratory measurements (1.8 ± 0.5 g/cm3); while AgHEC particle density showed wide variations (3.0 ± 0.5 g/cm3 and 1.2 + 0.1 g/cm3 for field and laboratory campaigns, respectively). This finding leads to speculation regarding the composition of particles emitted because atomized particle fragments may contain different Ag-to-HEC ratios, leading to different density values. A further uncertainty factor is probably related to low process emissions, making the subtraction of background concentrations from AgHEC process emissions unreliable.

Sustainable Use of Sludge from Industrial Park Wastewater Treatment Plants in Manufacturing Lightweight Aggregates.

The aim of this study was to investigate the development of a process for manufacturing lightweight aggregates (LWAs) by incorporating sludge from wastewater treatment plants in industrial parks with reservoir sediments. The research was divided into two stages: laboratory-scale firing and large-scale firing. In the laboratory-scale stage, a high-temperature furnace was used for trial firing. In the large-scale stage, a commercial rotary kiln was used for trial firing for mass production. The test results showed that the water absorption, dry loose bulk density, and crushing strength of the sintered LWAs were 14.2-26.9%, 634-753 kg/m3, and 1.29-2.90 MPa, respectively. Moreover, the water absorption of the sintered LWAs increased as the percentage of added sludge increased. In addition, the dry loose bulk density of the sintered LWAs gradually decreased as the percentage of added sludge increased. Moreover, the results of the heavy metal toxicity characteristic leaching procedure (TCLP) dissolution test for the LWAs produced by blending 30-50% sludge were all lower than the standard value required by the Taiwan Environmental Protection Agency for general industrial waste. The strength grade of the sintered LWAs was 20 MPa. From this point of view, the sintered LWAs that were studied under the test conditions could be used as aggregates for lightweight concrete and would allow it to have a reasonable strength of greater than 20 MPa.

Photogrammetry-Based Volume Measurement Framework for the Particle Density Estimation of LECA.

This paper presents a photogrammetry-based volume measurement framework for the particle density estimation of Lightweight expanded clay aggregate (LECA). The results are compared with computed tomography (CT) and Archimedes' method measurements. All of the steps required in order to apply the proposed approach are explained. Next, we discuss how the interpretation of open pores affects the results of volume measurements. We propose to process the shapes obtained from different methods by applying an Ambient Occlusion algorithm with the same threshold, t = 0.175. The difference between the CT and SfM methods is less than 0.006 g/cm3, proving that the photogrammetry-based approach is accurate enough. The Archimedes' method significantly overestimates the density of the particles. Nevertheless, its accuracy is acceptable for most engineering purposes. Additionally, we evaluate the accuracy of shape reconstruction (in terms of the Hausdorff distance). For 95% of the grain's surface, the maximum error is between 0.073 mm and 0.129 mm (depending on the grain shape). The presented approach is helpful for measuring the particle density of porous aggregates. The proposed methodology can be utilized in order to estimate intergranular porosity, which is valuable information for the calibration of DEM models.

Compression Modulus and Apparent Density of Polymeric Excipients during Compression-Impact on Tabletability.

The present study focuses on the compaction behavior of polymeric excipients during compression in comparison to nonpolymeric excipients and its consequences on commonly used Heckel analysis. Compression analysis at compaction pressures (CPs) from 50 to 500 MPa was performed using a compaction simulator. This study demonstrates that the particle density, measured via helium pycnometer (ρpar), of polymeric excipients (Kollidon®VA64, Soluplus®, AQOAT®AS-MMP, Starch1500®, Avicel®PH101) was already exceeded at low CPs (<200 MPa), whereas the ρpar was either never reached for brittle fillers such as DI-CAFOS®A60 and tricalcium citrate or exceeded at CPs above 350 MPa (FlowLac®100, Pearlitol®100SD). We hypothesized that the threshold for exceeding ρpar is linked with predominantly elastic deformation. This was confirmed by the start of linear increase in elastic recovery in-die (ERin-die) with exceeding particle density, and in addition, by the applicability in calculating the elastic modulus via the equation of the linear increase in ERin-die. Last, the evaluation of "density under pressure" as an alternative to the ρpar for Heckel analysis showed comparable conclusions for compression behavior based on the calculated yield pressures. However, the applicability of Heckel analysis for polymeric excipients was questioned in principle. In conclusion, the knowledge of the threshold provides guidance for the selection of suitable excipients in the formulation development to mitigate the risk of tablet defects related to stored elastic energy, such as capping and lamination.

Characterization, Density and In Vitro Controlled Release Properties of Mimosa (Acacia mearnsii) Tannin Encapsulated in Palm and Sunflower Oils.

Tannin has gained wider acceptance as a dietary supplement in contemporary animal nutrition investigations because of its potential to reduce enteric methane emission. However, a major drawback to dietary tannin intake is the bitter taste and instability in the gastrointestinal tract (GIT). The utilization of fats as coating materials will ensure appropriate masking of the tannin's aversive taste and its delivery to the target site. The aims of this study were to encapsulate mimosa tannin with palm oil or sunflower oil, and to assess the microcapsules in terms of encapsulation efficiency, morphology, density, and in vitro release of tannin in media simulating the rumen (pH 5.6), abomasum (pH 2.9) and small intestine (pH 7.4). The microencapsulation of mimosa tannin in palm or sunflower oils was accomplished using a double emulsion technique. The results revealed that encapsulated mimosa tannins in palm oil (EMTP) and sunflower oil (EMTS) had high yields (59% vs. 58%) and encapsulation efficiencies (70% vs. 68%), respectively. Compared to unencapsulated mimosa tannin (UMT), the morphology showed that the encapsulated tannins were smaller in size and spherical in shape. The UMT had (p < 0.01) higher particle density (1.44 g/cm3) compared to 1.22 g/cm3 and 1.21 g/cm3 for the EMTS and EMTP, respectively. The proportion of tannins released by the UMT after 24 h in the rumen (94%), abomasum (92%) and small intestine (96%) simulated buffers, reduced (p < 0.01) to 24%, 21% and 19% for the EMTS and 18%, 20% and 16% for the EMTP in similar media and timeframe. The release kinetics for the encapsulated tannins was slow and steady, thus, best fitted by the Higuchi model while the UMT dissolved quickly, hence, only fitted to a First order model. Sequential tannin release also indicated that the EMTS and EMTP were stable across the GIT. It was concluded that the microencapsulation of mimosa tannin in palm or sunflower oils stabilized tannins release in the GIT simulated buffers with the potential to modify rumen fermentation. Further studies should be conducted on the palm and sunflower oils microcapsules' lipid stability, fatty acid transfer rate in the GIT and antioxidant properties of the encapsulated tannins.

The Influence of Dry Hydrated Limes on the Fresh and Hardened Properties of Architectural Injection Grout.

Dry hydrated lime is an air binder often used in architectural injection grouts. This study compared the influences of three commercially available dry hydrated limes on the injection grouts' workability and mechanical properties. The main differences between the limes were in their chemical and mineralogical composition and Blaine specific surface area. The grouts were composed of dry hydrated lime, finely ground limestone filler, water, and super plasticiser. Subsequent results obtained revealed that the Blaine specific surface area is not directly related to the fresh grout properties. Grain size distribution and shape of lime particles and their aggregates in the water suspension are key parameters influencing the following fresh grout properties: fluidity, injectability, the mixture's stability, and water retention capacity. However, the lime injection grouts' mechanical strengths were higher in relation to an increase in the content of portlandite and the Blaine specific surface area of the dry hydrate.

Smash ridge tillage strongly influence soil functionality, physiology and rice yield.

The practice of smash-ridging on dry land crop cultivation has shown much promise. However, the mechanism how does soil functionality and root traits can affect rice yield under smash ridge tillage with reduced nitrogen fertilization have not yet been explored. To fill this knowledge gap, we used three tillage methods-smash-ridging 40 cm (S40), smash-ridging 20 cm (S20), and traditional turn-over plowing 20 cm (T)-and two rice varieties (hybrid rice and conventional rice) and measured soil quality, root traits, rice yield and their correlation analysis at different growth stages. Soil physical and chemical properties were significantly improved by smash-ridging, including improvements in root morphological and physiological traits during three growth stages compared with T. S40 had the highest leaf area index (LAI), plant height (PH), and biomass accumulation (BA). Increment in biomass and panicle number (PN) resulted in higher grain yield (GY) of 6.9-9.4% compared with T. Correlation analysis revealed that root total absorption area (RTAA), root active absorption area (RAA), and root area ratio (RAR) were strongly correlated with soil quality. Root injury flow (RIF) and root biomass accumulation (RBA) were strongly correlated with LAI and above-ground plant biomass accumulation (AGBA). Conclusively, S40 is a promising option for improving soil quality, root traits, and consequently GY.

Imaging Method for Measurements of Particle Density and Solid Holdup of Entangled MWCNTs in a Fluidized Bed.

A measurement method of the apparent particle density of the carbon nanotube (CNT) particles, characterized by enveloped volume formed by loosely entangled nanotubes, has been proposed for the CNT fluidized bed application. The method is characterized by obtaining the enveloped volume from the CNTs imaging under the free falling condition similar to the fluidized bed. The shape of the falling CNT particles in a column (0.1 m long × 0.012 m wide × 0.60 m high) was photographed using a high-speed camera under the sedimentation condition, and the apparent CNT particle density was calculated from the enveloped volume obtained by image-processing for the particles images. The apparent densities and solid holdups by the imaging method at various conditions were compared with those by the previous Hg-porosimetry method for the two types of CNTs (a vertically aligned CNT and two entangle CNTs) and the nonporous polycarbonate particle (a reference particle). The imaging method reflects well the packed bed and fluidized bed phenomena observed in the experiments with reasonable solid holdups, compared with the Hg-porosimetry method showing high densities and low holdups. The sizes of CNT particles predicted with the density by the imaging method were in good agreement with the measured mean particle sizes when calculated based on the Richardson-Zaki equation, indicating the imaging method represented well the enveloped volume and shape formed by entangled nanotubes on the CNTs.

The effects of particle size, shape, density and flow characteristics on particle margination to vascular walls in cardiovascular diseases.

INTRODUCTION: Vascular-targeted drug delivery is a promising approach for the treatment of atherosclerosis, due to the vast involvement of endothelium in the initiation and growth of plaque, a characteristic of atherosclerosis. One of the major challenges in carrier design for targeting cardiovascular diseases (CVD) is that carriers must be able to navigate the circulation system and efficiently marginate to the endothelium in order to interact with the target receptors. AREAS COVERED: This review draws on studies that have focused on the role of particle size, shape, and density (along with flow hemodynamics and hemorheology) on the localization of the particles to activated endothelial cell surfaces and vascular walls under different flow conditions, especially those relevant to atherosclerosis. EXPERT OPINION: Generally, the size, shape, and density of a particle affect its adhesion to vascular walls synergistically, and these three factors should be considered simultaneously when designing an optimal carrier for targeting CVD. Available preliminary data should encourage more studies to be conducted to investigate the use of nano-constructs, characterized by a sub-micrometer size, a non-spherical shape, and a high material density to maximize vascular wall margination and minimize capillary entrapment, as carriers for targeting CVD.

Catalyst Particle Density Controls Hydrocarbon Product Selectivity in CO2 Electroreduction on CuOx.

A key challenge of the carbon dioxide electroreduction (CO2RR) on Cu-based nanoparticles is its low faradic selectivity toward higher-value products such as ethylene. Here, we demonstrate a facile method for tuning the hydrocarbon selectivities on CuOx nanoparticle ensembles by varying the nanoparticle areal density. The sensitive dependence of the experimental ethylene selectivity on catalyst particle areal density is attributed to a diffusional interparticle coupling that controls the de- and re-adsorption of CO and thus the effective coverage of COad intermediates. Thus, higher areal density constitutes dynamically favored conditions for CO re-adsorption and *CO dimerization leading to ethylene formation independent of pH and applied overpotential.