Ru-P pair sites boost charge transport in hematite photoanodes for exceeding 1% efficient solar water splitting.

Fast transport of charge carriers in semiconductor photoelectrodes are a major determinant of the solar-to-hydrogen efficiency for photoelectrochemical (PEC) water slitting. While doping metal ions as single atoms/clusters in photoelectrodes has been popularly used to regulate their charge transport, PEC performances are often low due to the limited charge mobility and severe charge recombination. Here, we disperse Ru and P diatomic sites onto hematite (DASs Ru-P:Fe2O3) to construct an efficient photoelectrode inspired by the concept of correlated single-atom engineering. The resultant photoanode shows superior photocurrent densities of 4.55 and 6.5 mA cm-2 at 1.23 and 1.50 VRHE, a low-onset potential of 0.58 VRHE, and a high applied bias photon-to-current conversion efficiency of 1.00% under one sun illumination, which are much better than the pristine Fe2O3. A detailed dynamic analysis reveals that a remarkable synergetic ineraction of the reduced recombination by a low Ru doping concentration with substitution of Fe site as well as the construction of Ru-P bonds in the material increases the carrier separation and fast charge transportation dynamics. A systematic simulation study further proves the superiority of the Ru-P bonds compared to the Ru-O bonds, which allows more long-lived carriers to participate in the water oxidation reaction. This work offers an effective strategy for enhancing charge carrier transportation dynamics by constructing pair sites into semiconductors, which may be extended to other photoelectrodes for solar water splitting.

Origin of Enhanced Photoelectrochemical Activity of the n-CdS/p-type Semiconductor Interface: Homojunction or Heterojunction?

Surface engineering of photoelectrodes is considered critical for achieving efficient photoelectrochemical (PEC) cells, and various p-type materials have been investigated for use as photoelectrodes. Among these, the p-type semiconductor/n-type CdS heterojunction is the most successful photocathode structure because of its enhanced onset potential and photocurrent. However, it is determined that the main contributor to the enhanced activity is the Cd-doped layer and not the CdS layer. In this study, a Cd-doped n+p-buried homojunction of a CuInS2 photocathode is first demonstrated without a CdS layer. The homojunction exhibited a more active and stable PEC performance than the CdS/CuInS2 heterojunction. Moreover, it is confirmed that Cd doping is effective for other p-type materials. These results strongly suggest that the effects of Cd doping on photocathodes should be carefully investigated when designing CdS/p-semiconductor heterojunction photoelectrodes. They also indicate that the Cd-doped layer has great potential to replace the CdS layer in future photoelectrode designs.

Static Organic p-n Junctions in Photoelectrodes for Solar Ammonia Production with 86 % Internal Quantum Efficiency.

For photoelectrocatalytic cells, a limitation exists in finding appropriate photoelectrode configurations that couple efficient extraction of high-energy electrons from absorbed photons and selective catalysis. Here we report an organic p-n junction approach to fabricate molecular photoelectrodes for conversion of solar energy and nitrate into valuable ammonia product. Solar irradiation of the photoelectrode generates charge-separated states with electrons and holes spatially separated at the n-type and p-type components, as revealed by surface photovoltage mapping, at a quantum yield of 90 %. The high-flux photogenerated electrons are rapidly transferred to the catalyst for solar ammonia production from nitrate reduction at an external quantum efficiency (EQE) and an internal quantum efficiency (IQE) of 57 % and 86 %, respectively. Time-resolved spectroscopic studies reveal that the large IQE originates from the combined high efficiencies for photoelectron generation, catalyst activation and dark catalysis. In a flow-cell setup coupled with a silicon solar cell, the photoelectrode without bias generates photocurrent of 57 mA cm-2 and ammonia at an EQE of 52 %.

Unbiased Photoelectrochemical H2O2 Coupled to H2 Production via Dual Sb2S3-Based Photoelectrodes with Ultralow Onset Potential.

The productions of hydrogen peroxide (H2O2) and hydrogen (H2) in a photoelectrochemical (PEC) water splitting cell suffer from an onset potential that limits solar conversion efficiencies. Moreover, the formation of H2O2 through two-electron PEC water oxidation reaction competes with four-electron oxidation evolution reaction. Herein, we developed the surface selenium doped antimony trisulfide photoelectrode with the integrated ruthenium cocatalyst (Ru/Sb2(S,Se)3) to achieve the low onset potential and high Faraday efficiency (FE) for selective H2O2 production. The photoanode exhibits an outstanding average FE of 85 % in the potential range of 0.4-1.6 VRHE and the H2O2 yield of 1.01 µmol cm-2 min-1 at 1.6 VRHE, especially at low potentials of 0.1-0.55 VRHE with 80.4 % FE. Impressively, an unassisted PEC system that employs light and electrolyte was constructed to simultaneously produce H2O2 and H2 production on both the Ru/Sb2(S,Se)3 photoanode and the Pt/TiO2/Sb2S3 photocathode. The integrated system enables the average PEC H2O2 production rate of 0.637 µmol cm-2 min-1 without applying any addition bias. To our knowledge, this is the first demonstration that Sb2S3-based photoelectrodes exhibit H2O2/H2 two-side production with a strict key factor of the system, which represents its powerful platform to achieve high efficiency and productivity and the feasibility to facilitate value-added products in neutral conditions.

Solar Energy Storage Using a Cu2 O-TiO2 Photocathode in a Lithium Battery.

A Cu2 O-TiO2 photoelectrode is pr+oposed for simultaneous solar light energy harvesting and storing of electrochemical energy in an adapted lithium coin cell. The p-type Cu2 O semiconductor layer is the light harvester component of the photoelectrode and the TiO2 film performs as the capacitive layer. The rationale of the energy scheme shows that the photocharges generated in the Cu2 O semiconductor induce lithiation/delithiation processes in the TiO2 film as a function of the applied bias voltage and light power. A photorechargeable lithium button cell drilled on one side recharges with visible white light in ≈9 h in open circuit. It provides an energy density of ≈150 mAh g-1 at 0.1 C discharge current in dark, and the overall efficiency is 0.29%. This work draws a new approach for the photoelectrode role to advance in monolithic rechargeable batteries.

Photoelectrochemical Engineering for Light-Assisted Rechargeable Metal Batteries: Mechanism, Development, and Future.

Rechargeable battery devices with high energy density are highly demanded by  our  modern society. The use of metal anodes is extremely attractive for future rechargeable battery devices. However, the notorious metal dendritic and instability of solid electrolyte interface issues pose a series of challenges for metal anodes. Recently, considering the indigestible dynamical behavior of metal anodes, photoelectrochemical engineering of light-assisted metal anodes have been rapidly developed since they efficiently utilize the integration and synergy of oriented crystal engineering and photocatalysis engineering, which provided a potential way to unlock the interface electrochemical mechanism and deposition reaction kinetics of metal anodes. This review starts with the fundamentals of photoelectrochemical engineering and follows with the state-of-art advance of photoelectrochemical engineering for light-assisted rechargeable metal batteries where photoelectrode materials, working principles, types, and practical applications are explained. The last section summarizes the major challenges and some invigorating perspectives for future research on light-assisted rechargeable metal batteries.

Integrated Photovoltaic Charging and Energy Storage Systems: Mechanism, Optimization, and Future.

As an emerging solar energy utilization technology, solar redox batteries (SPRBs) combine the superior advantages of photoelectrochemical (PEC) devices and redox batteries and are considered as alternative candidates for large-scale solar energy capture, conversion, and storage. In this review, a systematic summary from three aspects, including: dye sensitizers, PEC properties, and photoelectronic integrated systems, based on the characteristics of rechargeable batteries and the advantages of photovoltaic technology, is presented. The matching problem of high-performance dye sensitizers, strategies to improve the performance of photoelectrode PEC, and the working mechanism and structure design of multienergy photoelectronic integrated devices are mainly introduced and analyzed. In particular, the devices and improvement strategies of high-performance electrode materials are analyzed from the perspective of different photoelectronic integrated devices (liquid-based and solid-state-based). Finally, future perspectives are provided for further improving the performance of SPRBs. This work will open up new prospects for the development of high-efficiency photoelectronic integrated batteries.

Advanced Nanostructured Conjugated Microporous Polymer Application in a Tandem Photoelectrochemical Cell for Hydrogen Evolution Reaction.

Solar energy conversion through photoelectrochemical cells by organic semiconductors is a hot topic that continues to grow due to the promising optoelectronic properties of this class of materials. In this sense, conjugated polymers have raised the interest of researchers due to their interesting light-harvesting properties. Besides, their extended π-conjugation provides them with an excellent charge conduction along the whole structure. In particular, conjugated porous polymers (CPPs) exhibit an inherent porosity and three-dimensional structure, offering greater surface area, and higher photochemical and mechanical stability than their linear relatives (conjugated polymers, CPs). However, CPP synthesis generally provides large particle powders unsuitable for thin film preparation, limiting its application in optoelectronic devices. Here, a synthetic strategy is presented to prepare nanostructures of a CPP suitable to be used as photoelectrode in a photoelectrochemical (PEC) cell. In this way, electronic and photoelectrochemical properties are measured and, attending to the optoelectronic properties, two hybrid photoelectrodes (photoanode and photocathode) are designed and built to assemble a tandem PEC cell. The final device exhibits photocurrents of 0.5 mA cm-2 at a 0.7 V in the two electrode configuration and the hydrogen evolution reaction is observed and quantified by gas chromatography, achieving 581 µmol of H2 in a one-hour reaction.

Steering the Pathway of Plasmon-Enhanced Photoelectrochemical CO2 Reduction by Bridging Si and Au Nanoparticles through a TiO2 Interlayer.

Photoelectrochemical (PEC) conversion of CO2 in an aqueous medium into high-energy fuels is a creative strategy for storing solar energy and closing the anthropogenic carbon cycle. However, the rational design of catalytic architectures to selectively and efficiently produce a target product such as CO has remained a grand challenge. Herein, an efficient and selective Si photocathode for CO production is reported by utilizing a TiO2 interlayer to bridge the Au nanoparticles and n+ p-Si. The TiO2 interlayer can not only effectively protect and passivate Si surface, but can also exhibit outstanding synergies with Au nanoparticles to greatly promote CO2 reduction kinetics for CO production through stabilizing the key reaction intermediates. Specifically, the TiO2 layer and Au nanoparticles work concertedly to enhance the separation of localized surface plasmon resonance generated hot carriers, contributing to the improved activity and selectivity for CO production by utilizing the hot electrons generated in Au nanoparticles during PEC CO2 reduction. The optimized Au/TiO2 /n+ p-Si photocathode exhibits a Faradaic efficiency of 86% and a partial current density of -5.52 mA cm-2 at -0.8 VRHE for CO production, which represent state-of-the-art performance in this field. Such a plasmon-enhanced strategy may pave the way for the development of high-performance PEC photocathodes for energy-efficient CO2 utilization.

Electron Transfer in a Bio-Photoelectrode Based on Photosystem I Multilayer Immobilized on the Conducting Glass.

A film of ~40 layers of partially oriented photosystem I (PSI) complexes isolated from the red alga Cyanidioschyzon merolae formed on the conducting glass through electrodeposition was investigated by time-resolved absorption spectroscopy and chronoamperometry. The experiments were performed at a range of electric potentials applied to the film and at different compositions of electrolyte solution being in contact with the film. The amount of immobilized proteins supporting light-induced charge separation (active PSI) ranged from ~10%, in the absence of any reducing agents (redox compounds or low potential), to ~20% when ascorbate and 2,6-dichlorophenolindophenol were added, and to ~35% when the high negative potential was additionally applied. The origin of the large fraction of permanently inactive PSI (65-90%) was unclear. Both reducing agents increased the subpopulation of active PSI complexes, with the neutral P700 primary electron donor, by reducing significant fractions of the photo-oxidized P700 species. The efficiencies of light-induced charge separation in the PSI film (10-35%) did not translate into an equally effective generation of photocurrent, whose internal quantum efficiency reached the maximal value of 0.47% at the lowest potentials. This mismatch indicates that the vast majority of the charge-separated states in multilayered PSI complexes underwent charge recombination.

In-situ electrodeposition synthesis of Z-scheme rGO/g-C3N4/TNAs photoelectrodes and its degradation mechanism for oxytetracycline in dual-chamber photoelectrocatalytic system.

The dual-chamber photoelectrocatalytic (PEC) system possess advantages in the degradation efficiency and processing cost of organic contaminants. In this study, TiO2 nanotube arrays modified by rGO and g-C3N4 (rGO/g-C3N4/TNAs) photoelectrodes were successfully prepared. The surface micromorphology, chemical structure, crystal structure, and basic element composition of rGO/g-C3N4/TNAs photoelectrodes were studied by SEM, FTIR, XRD, Raman, and XPS. UV-vis absorption, photoluminescence (PL) spectra, and photoelectrochemical (PECH) tests were used to explore the photoelectrochemical characteristics of rGO/g-C3N4/TNAs photoelectrodes. Under simulated sunlight illumination, the dual-chamber PEC system with external bias voltage was used to investigate the degradation of oxytetracycline (OTC) on rGO/g-C3N4/TNAs photoelectrodes. The results showed that rGO and g-C3N4 were successfully loaded on TNAs, and the separation efficiency of electrons and holes at rGO/g-C3N4/TNAs photoelectrodes was improved. The light absorption range of rGO/g-C3N4/TNAs photoelectrodes extends to the visible light region and has better light absorption performance. Compared with the photocatalytic process, when 1.2 V bias voltage was applied, the degradation efficiency of OTC in anode and cathode chambers in PEC were increased by 3.28% and 44.01% within 60 min, respectively. In addition, the anode and cathode chambers have different degradation effects on OTC. Both the external bias voltage and initial pH have significant effects in cathode chamber, but have little effect in photoanode chamber. The fluorescence excitation-emission matrix spectra and liquid chromatography-tandem mass spectrometry showed that there were different intermediates in the degradation process of OTC. This study indicated that for the dual-chamber PEC system, rGO/g-C3N4/TNAs photoelectrodes exhibited excellent photocatalytic performance and have potential application prospects in water environmental remediation.

Improving Performance of an Integrated Solar Flow Battery by Cr- and Cu-Doped TiO2 Photoelectrodes.

This work reports on the preparation of Cr-doped TiO2 (Cr−TiO2), Cu-doped (Cu-TiO2), and its utilization in the photoanode of a solar redox flow battery (SRFB). A pure TiO2 electrode, Cr-doped TiO2 electrode, and Cu-doped TiO2 electrode coated with different layers are prepared by the sol-gel method. XRD, XPS, and SEM are used to characterize the relevant data of the electrode. All three electrodes show the structure of the anatase phase, but the Cu-TiO2 and Cr-TiO2 electrodes are more crystalline. Using these materials as photoelectrodes to prepare integrated solar flow cells, the semi-cell and full-cell tests show that the doping of Cr and Cu improves the efficiency and charging current of solar cells. The average charging currents of the Cu-TiO2 and Cr-TiO2 electrodes are 384.20 µA and 450.75 µA, respectively, compared with the TiO2 electrode; this increment reaches values of 71.23% and 100.97%.

How to Build Prussian Blue Based Water Oxidation Catalytic Assemblies: Common Trends and Strategies.

Prussian blue (PB) and its analogues (PBAs) have at least a three-century-long history in coordination chemistry. Recently, cobalt-based PBAs have been acknowledged as efficient and robust water oxidation catalysts. Given the flexibility in their synthesis, the structure and morphology of cobalt-based PBAs have been modified for enhanced catalytic activity under electrochemical (EC), photocatalytic (PC), and photoelectrochemical (PEC) conditions. Here, in this review, the work on cobalt-based PBAs is presented in four sections: i) electrocatalytic water oxidation with bare PBAs, ii) photocatalytic processes in the presence of a photosensitizer (PS), iii) photoelectrochemical water oxidation by coupling PBAs to proper semiconductors (SCs), and iv) the utilization of PBA-PS assemblies coated on SCs for the dye-sensitized photoelectrochemical water oxidation. This review will guide readers through the structure and catalytic activity relationship in cobalt-based PBAs by describing the role of each structural component. Furthermore, this review aims to provide insight into common strategies to enhance the catalytic activity of PBAs.

Quantifying Photocurrent Loss of a Single Particle-Particle Interface in Nanostructured Photoelectrodes.

Particle-particle interfaces are ubiquitous in nanostructured photoelectrodes and photovoltaics, which are important devices for solar energy conversion. These interfaces are expected to cause performance losses in these devices, but how much loss they would incur is poorly defined. Here we use a subparticle photoelectrochemical current measurement, in combination with specific photoelectrode configurations, to quantify the current losses from single particle-particle interfaces formed between individual TiO2 nanorods operating as photoanodes in aqueous electrolytes. We find that a single interface leads to ∼20% photocurrent loss (i.e., ∼80% retention of the original current). Such quantitative, first-of-its-kind, information provides a metric for guiding the optimization and design of nanostructured photoelectrodes and photovoltaics.

Synthetic Photoelectrochemistry.

Photoredox catalysis (PRC) and synthetic organic electrochemistry (SOE) are often considered competing technologies in organic synthesis. Their fusion has been largely overlooked. We review state-of-the-art synthetic organic photoelectrochemistry, grouping examples into three categories: 1) electrochemically mediated photoredox catalysis (e-PRC), 2) decoupled photoelectrochemistry (dPEC), and 3) interfacial photoelectrochemistry (iPEC). Such synergies prove beneficial not only for synthetic "greenness" and chemical selectivity, but also in the accumulation of energy for accessing super-oxidizing or -reducing single electron transfer (SET) agents. Opportunities and challenges in this emerging and exciting field are discussed.

Perovskite Oxide Based Electrodes for High-Performance Photoelectrochemical Water Splitting.

Photoelectrochemical (PEC) water splitting is an attractive strategy for the large-scale production of renewable hydrogen from water. Developing cost-effective, active and stable semiconducting photoelectrodes is extremely important for achieving PEC water splitting with high solar-to-hydrogen efficiency. Perovskite oxides as a large family of semiconducting metal oxides are extensively investigated as electrodes in PEC water splitting owing to their abundance, high (photo)electrochemical stability, compositional and structural flexibility allowing the achievement of high electrocatalytic activity, superior sunlight absorption capability and precise control and tuning of band gaps and band edges. In this review, the research progress in the design, development, and application of perovskite oxides in PEC water splitting is summarized, with a special emphasis placed on understanding the relationship between the composition/structure and (photo)electrochemical activity.

Promoted Fixation of Molecular Nitrogen with Surface Oxygen Vacancies on Plasmon-Enhanced TiO2 Photoelectrodes.

A hundred years on, the energy-intensive Haber-Bosch process continues to turn the N2 in air into fertilizer, nourishing billions of people while causing pollution and greenhouse gas emissions. The urgency of mitigating climate change motivates society to progress toward a more sustainable method for fixing N2 that is based on clean energy. Surface oxygen vacancies (surface Ovac ) hold great potential for N2 adsorption and activation, but introducing Ovac on the very surface without affecting bulk properties remains a great challenge. Fine tuning of the surface Ovac by atomic layer deposition is described, forming a thin amorphous TiO2 layer on plasmon-enhanced rutile TiO2 /Au nanorods. Surface Ovac in the outer amorphous TiO2 thin layer promote the adsorption and activation of N2 , which facilitates N2 reduction to ammonia by excited electrons from ultraviolet-light-driven TiO2 and visible-light-driven Au surface plasmons. The findings offer a new approach to N2 photofixation under ambient conditions (that is, room temperature and atmospheric pressure).

Enhanced Photoelectrochemical Performance in Reduced Graphene Oxide/BiFeO3 Heterostructures.

BiFeO3 (BFO)-based ferroelectrics have been proved to be visible-light-driven photoelectrodes for O2 production. However, the hitherto reported photoelectrochemical performances remain inferior to meet the requirements for any applications. Besides, expensive noble metals (Ag, Au) are commonly required to achieve high photoelectric conversion efficiency. Here, the significant enhancements of photoelectrochemical performance is reported by fabricating a noble-metal-free reduced graphene oxide (RGO)/BFO composite film via a simple and cost-effective solution process. The optimized RGO/BFO composite film exhibits a 600% improvement of the short-circuit photocurrent density compared to that of the pristine BFO, and also outperforms the noble-metal/BFO cells under the same reaction conditions. Furthermore, the incident photon-to-current efficiency of the optimized RGO/BFO sample shows threefold enhancement. This study delivers a facile and low-cost approach to preparing 2D materials/ferroelectric heterostructures and offers a promising pathway to boost the performance of semiconducting ferroelectric photoelectrodes.

Ultrafast Flame Annealing of TiO2 Paste for Fabricating Dye-Sensitized and Perovskite Solar Cells with Enhanced Efficiency.

Mesoporous TiO2 nanoparticle (NP) films are broadly used as electrodes in photoelectrochemical cells, dye-sensitized solar cells (DSSCs), and perovskite solar cells (PSCs). State-of-the-art mesoporous TiO2 NP films for these solar cells are fabricated by annealing TiO2 paste-coated fluorine-doped tin oxide glass in a box furnace at 500 °C for ≈30 min. Here, the use of a nontraditional reactor, i.e., flame, is reported for the high throughput and ultrafast annealing of TiO2 paste (≈1 min). This flame-annealing method, compared to conventional furnace annealing, exhibits three distinct benefits. First, flame removes polymeric binders in the initial TiO2 paste more completely because of its high temperature (≈1000 °C). Second, flame induces strong interconnections between TiO2 nanoparticles without affecting the underlying transparent conducting oxide substrate. Third, the flame-induced carbothermic reduction on the TiO2 surface facilitates charge injection from the dye/perovskite to TiO2 . Consequently, when the flame-annealed mesoporous TiO2 film is used to fabricate DSSCs and PSCs, both exhibit enhanced charge transport and higher power conversion efficiencies than those fabricated using furnace-annealed TiO2 films. Finally, when the ultrafast flame-annealing method is combined with a fast dye-coating method to fabricate DSSC devices, its total fabrication time is reduced from over 3 h to ≈10 min.

Computational insights into charge transfer across functionalized semiconductor surfaces.

Photoelectrochemical water-splitting is a promising carbon-free fuel production method for producing H2 and O2 gas from liquid water. These cells are typically composed of at least one semiconductor photoelectrode which is prone to degradation and/or oxidation. Various surface modifications are known for stabilizing semiconductor photoelectrodes, yet stabilization techniques are often accompanied by a decrease in photoelectrode performance. However, the impact of surface modification on charge transport and its consequence on performance is still lacking, creating a roadblock for further improvements. In this review, we discuss how density functional theory and finite-element device simulations are reliable tools for providing insight into charge transport across modified photoelectrodes.