Regulating Lewis Acidic Sites of 1T-2H MoS2 Catalysts for Solar-Driven Photothermal Catalytic H2 Production from Lignocellulosic Biomass.

Solar-driven photothermal catalytic H2 production from lignocellulosic biomass was achieved by using 1T-2H MoS2 with tunable Lewis acidic sites as catalysts in an alkaline aqueous solution, in which the number of Lewis acidic sites derived from the exposed Mo edges of MoS2 was successfully regulated by both the formation of an edge-terminated 1T-2H phase structure and tunable layer number. Owing to the abundant Lewis acidic sites for the oxygenolysis of lignocellulosic biomass, the 1T-2H MoS2 catalyst shows high photothermal catalytic lignocellulosic biomass-to-H2 transformation performance in polar wood chips, bamboo, rice straw corncobs, and rice hull aqueous solutions, and the highest H2 generation rate and solar-to-H2 (STH) efficiency respectively achieves 3661 µmol·h-1·g-1 and 0.18% in the polar wood chip system under 300 W Xe lamp illumination. This study provides a sustainable and cost-effective method for the direct transformation of renewable lignocellulosic biomass to H2 fuel driven by solar energy.

Guiding the Driving Factors on Plasma Super-Photothermal S-Scheme Core-Shell Nanoreactor to Enhance Photothermal Catalytic H2 Evolution and Selective CO2 Reduction.

Light-induced heat has a non-negligible role in photocatalytic reactions. However, it is still challenging to design highly efficient catalysts that can make use of light and thermal energy synergistically. Herein, the study proposes a plasma super-photothermal S-scheme heterojunction core-shell nanoreactor based on manipulation of the driving factors, which consists of α-Fe2 O3 encapsulated by g-C3 N4 modified with gold quantum dots. α-Fe2 O3 can promote carrier spatial separation while also acting as a thermal core to radiate heat to the shell, while Au quantum dots transfer energetic electrons and heat to g-C3 N4 via surface plasmon resonance. Consequently, the catalytic activity of Au/α-Fe2 O3 @g-C3 N4 is significantly improved by internal and external double hot spots, and it shows an H2 evolution rate of 5762.35 µmol h-1 g-1 , and the selectivity of CO2 conversion to CH4 is 91.2%. This work provides an effective strategy to design new plasma photothermal catalysts for the solar-to-fuel transition.

Hollow g-C3N4@Ag3PO4 Core-Shell Nanoreactor Loaded with Au Nanoparticles: Boosting Photothermal Catalysis in Confined Space.

Low solar energy utilization efficiency and serious charge recombination remain major challenges for photocatalytic systems. Herein, a hollow core-shell Au/g-C3N4@Ag3PO4 photothermal nanoreactor is successfully prepared by a two-step deposition method. Benefit from efficient spectral utilization and fast charge separation induced by the unique hollow core-shell heterostructure, the H2 evolution rate of Au/g-C3N4@Ag3PO4 is 16.9 times that of the pristine g-C3N4, and the degradation efficiency of tetracycline is increased by 88.1%. The enhanced catalytic performance can be attributed to the ordered charge movement on the hollow core-shell structure and a local high-temperature environment, which effectively accelerates the carrier separation and chemical reaction kinetics. This work highlights the important role of the space confinement effect in photothermal catalysis and provides a promising strategy for the development of the next generation of highly efficient photothermal catalysts.

Structural Heredity in Catalysis: CO2 Self-Selective CeO2 Nanocrystals for Efficient Photothermal CO2 Hydrogenation to Methane.

The chemical inertness of CO2 molecules makes their adsorption and activation on a catalyst surface one of the key challenges in recycling CO2 into chemical fuels. However, the traditional template synthesis and chemical modification strategies used to tackle this problem face severe structural collapse and modifier deactivation issues during the often-needed post-processing procedure. Herein, a CO2 self-selective hydrothermal growth strategy is proposed for the synthesis of CeO2 octahedral nanocrystals that participate in strong physicochemical interactions with CO2 molecules. The intense affinity for CO2 molecules persists during successive high-temperature treatments required for Ni deposition. This demonstrates the excellent structural heredity of the CO2 self-selective CeO2 nanocrystals, which leads to an outstanding photothermal CH4 productivity exceeding 9 mmol h-1 mcat -2 and an impressive selectivity of >99%. The excellent performance is correlated with the abundant oxygen vacancies and hydroxyl species on the CeO2 surface, which create many frustrated Lewis-pair active sites, and the strong interaction between Ni and CeO2 that promotes the dissociation of H2 molecules and the spillover of H atoms, thereby greatly benefitting the photothermal CO2 methanation reaction. This self-selective hydrothermal growth strategy represents a new pathway for the development of effective catalysts for targeted chemical reactions.

Customized Ultrathin Oxygen Vacancy-Rich Bi2W0.2Mo0.8O6 Nanosheets Enabling a Stepwise Charge Separation Relay and Exposure of Lewis Acid Sites toward Broad-Spectrum Photothermal Catalysis.

Designing robust photocatalysts with broad light absorption, effective charge separation, and sufficient reactive sites is critical for achieving efficient solar energy conversion. However, realizing these aims simultaneously through a single material modulation approach poses a challenge. Here, a 2D ultrathin oxygen vacancy (Ov)-rich Bi2W0.2Mo0.8O6 solid solution photocatalyst is designed and fabricated to tackle the dilemma through component and structure optimization. Specifically, the construction of a solid solution with ultrathin structure initially facilitates the separation of photoinduced electron-hole pairs, while the introduction of Ov strengthens such separation. In the meantime, the presence of Ov extends light absorption to the NIR region, triggering a photothermal effect that further enhances the charge separation and accelerates the redox reaction. As such, photoinduced charge carriers in the Ov-Bi2W0.2Mo0.8O6 are separated step by step via the synergistic action of 2D solid solution, OV, and solar heating. Furthermore, the introduction of OV exposes surface metal sites that serve as reactive Lewis acid sites, promoting the adsorption and activation of toluene. Consequently, the designed Ov-Bi2W0.2Mo0.8O6 reveals an enhanced photothermal catalytic toluene oxidation rate of 2445 µmol g-1 h-1 under a wide spectrum without extra heat input. The performance is 9.0 and 3.9 times that of Bi2WO6 and Bi2MoO6 nanosheets, respectively.

Efficient Photothermal Catalytic Oxidation Enabled by Three-Dimensional Nanochannel Substrates.

Photothermal catalysis exhibits promising prospects to overcome the shortcomings of high-energy consumption of traditional thermal catalysis and the low efficiency of photocatalysis. However, there is still a challenge to develop catalysts with outstanding light absorption capability and photothermal conversion efficiency for the degradation of atmospheric pollutants. Herein, we introduced the Co3O4 layer and Pt nanoclusters into the three-dimensional (3D) porous membrane through the atomic layer deposition (ALD) technique, leading to a Pt/Co3O4/AAO monolithic catalyst. The 3D ordered nanochannel structure can significantly enhance the solar absorption capacity through the light-trapping effect. Therefore, the embedded Pt/Co3O4 catalyst can be rapidly heated and the O2 adsorbed on the Pt clusters can be activated to generate sufficient O2- species, exhibiting outstanding activity for the diverse VOCs (toluene, acetone, and formaldehyde) degradation. Optical characterization and simulation calculation confirmed that Pt/Co3O4/AAO exhibited state-of-the-art light absorption and a notable localized surface plasmon resonance (LSPR) effect. In situ diffuse reflectance infrared Fourier transform spectrometry (in situ DRIFTS) studies demonstrated that light irradiation can accelerate the conversion of intermediates during toluene and acetone oxidation, thereby inhibiting byproduct accumulation. Our finding extends the application of AAO's optical properties in photothermal catalytic degradation of air pollutants.

Boosting Photothermocatalytic Oxidation of Toluene Over Pt/N-TiO2: The Gear Effect of Light and Heat.

Photothermal catalysis is extremely promising for the removal of various indoor pollutants owing to its photothermal synergistic effect, while the low light utilization efficiency and unclear catalytic synergistic mechanism hinder its practical applications. Here, nitrogen atoms are introduced, and Pt nanoparticles are loaded on TiO2 to construct Pt/N-TiO2-H2, which exhibits 3.5-fold higher toluene conversion rate than the pure TiO2. Compared to both photocatalytic and thermocatalytic processes, Pt/N-TiO2-H2 exhibited remarkable performance and stability in the photothermocatalytic oxidation of toluene, achieving 98.4% conversion and 98.3% CO2 yield under a light intensity of 260 mW cm-2. Furthermore, Pt/N-TiO2-H2 demonstrated potential practical applicability in the photothermocatalytic elimination of various indoor volatile organic compounds. The synergistic effect occurs as thermocatalysis accelerates the accumulation of carboxylate species and the degradation of aldehyde species, while photocatalysis promotes the generation of aldehyde species and the consumption of carboxylate species. This ultimately enhances the photothermocatalytic process. The photothermal synergistic effect involves the specific conversion of intermediates through the interplay of light and heat, providing novel insights for the design of photothermocatalytic materials and the understanding of photothermal mechanisms.

Generation of oxygen vacancies in CuO/TiO2 heterojunction induced by diatomite for highly efficient UV-Vis-IR driven photothermal catalytic oxidation of HCHO.

Photothermal catalytic oxidation is a promising and sustainable method for the degradation of indoor formaldehyde (HCHO). However, the excessively high surface temperature of existing photothermal catalysts during catalysis hinders the effective adsorption and degradation of formaldehyde under static conditions. Catalyst loading and oxygen vacancies (OVs) modulation are commonly employed strategies to reduce the photothermal catalytic temperature and enhance the efficiency of photothermal catalytic oxidation. In this work, a p-n type CuO/TiO2 heterojunction is successfully loaded onto diatomite using a wet precipitation method. Under the irradiation of a 300W xenon lamp, the prepared composite material achieved a 100% removal rate of HCHO within 2 h, with a 98% conversion rate to CO2, surpassing the performance of both individual photocatalysts and thermocatalysts. Additionally, by adjusting conditions such as light irradiation and temperature, we have demonstrated that this material exhibits synergistic photothermal catalytic properties. Based on HRTEM, XPS, Raman, and EPR analyses, the introduction of diatomite as a catalyst support was shown to effectively increase the number of OVs. Experimental results, along with O2-TPD, photoelectrochemical characterization, and radical detection, demonstrate that the presence of OVs enhances the oxidative efficiency of both photocatalysis and thermocatalysis, as well as the UV-Vis-IR photothermal catalytic performance. The ternary composite material generates weak hydroxyl (•OH) and superoxide (•O2-) radical under high-temperature with dark conditions, indicating its catalytic oxidation activity under this condition. The increase in temperature and the expansion of the spectral range both enhance the generation of these radicals. In summary, this work demonstrates that the use of diatomite as a support increases the material's specific surface area and OVs content, thereby enhancing adsorption and photothermal catalysis. It elucidates the enhanced catalytic degradation mechanism of this mineral-based photothermal catalyst.

Development of Plasmonic Attapulgite/Co(Ti)Ox Nanocomposite Using Spent Batteries toward Photothermal Reduction of CO2.

The rapid development of the battery industry has brought about a large amount of waste battery pollution. How to realize the high-value utilization of waste batteries is an urgent problem to be solved. Herein, cobalt and titanium compounds (LTCO) were firstly recovered from spent lithium-ion batteries (LIBs) using the carbon thermal reduction approach, and plasmonic attapulgite/Co(Ti)Ox (H-ATP/Co(Ti)Ox) nanocomposites were prepared by the microwave hydrothermal technique. H-ATP had a large specific surface area and enough active sites to capture CO2 molecules. The biochar not only reduced the spinel phase of waste LIBs into metal oxides including Co3O4 and TiO2 but also increased the separation and transmission of the carriers, thereby accelerating the adsorption and reduction of CO2. In addition, H-ATP/Co(Ti)Ox exhibited a localized surface plasmon resonance effect (LSPR) in the visible to near-infrared region and released high-energy hot electrons, enhancing the surface temperature of the catalyst and further improving the catalytic reduction of CO2 with a high CO yield of 14.7 µmol·g-1·h-1. The current work demonstrates the potential for CO2 reduction by taking advantage of natural mineral and spent batteries.

Applications of Ni-Based Catalysts in Photothermal CO2 Hydrogenation Reaction.

Heterogeneous CO2 hydrogenation catalytic reactions, as the strategies for CO2 emission reduction and green carbon resource recycling, play important roles in alleviating global warming and energy shortages. Among these strategies, photothermal CO2 hydrogenation technology has become one of the hot catalytic technologies by virtue of the synergistic advantages of thermal catalysis and photocatalysis. And it has attracted more and more researchers' attentions. Various kinds of effective photothermal catalysts have been gradually discovered, and nickel-based catalysts have been widely studied for their advantages of low cost, high catalytic activity, abundant reserves and thermal stability. In this review, the applications of nickel-based catalysts in photothermal CO2 hydrogenation are summarized. Finally, through a good understanding of the above applications, future modification strategies and design directions of nickel-based catalysts for improving their photothermal CO2 hydrogenation activities are proposed.

Regulating the Scaling Relations in Ammonia Synthesis through a Light-Driven Bendable Seesaw Effect on Tailored Iron Catalyst.

Advancing the energy-intensive Haber-Bosch process faces significant challenges due to the intrinsic constraints of scaling relations in heterogeneous catalysis. Herein, we reported an approach of bending the "seesaw effect" to regulate the scaling relations over a tailored α-Fe metallic material (α-Fe-110s), realizing highly efficient light-driven thermal catalytic ammonia synthesis with a rate of 1260 µmol gcatalyst -1 h-1 without additional heating. Specifically, the thermal catalytic activity of α-Fe-110s was significantly enhanced by the novel stepped {110} surface, exhibiting a 3.8-fold increase compared to the commercial fused-iron catalyst with promoters at 350 °C. The photo-induced hot electron transfer further accelerates the dinitrogen dissociation and hydrogenation simultaneously, effectively overcoming the limitation of scaling relation over identical sites. Consequently, the ammonia production rate of α-Fe-110s was further enhanced by 30 times at the same temperature with irradiation. This work designs an efficient and sustainable system for ammonia synthesis and provides a novel approach for regulating the scaling relations in heterogeneous catalysis.

Photothermal Synergistic Effect Induces Bimetallic Cooperation to Modulate Product Selectivity of CO2 Reduction on Different CeO2 Crystal Facets.

Product selectivity of solar-driven CO2 reduction and H2O oxidation reactions has been successfully controlled by tuning the spatial distance between Pt/Au bimetallic active sites on different crystal facets of CeO2 catalysts. The replacement depth of Ce atoms by monatomic Pt determines the distance between bimetallic sites, while Au clusters are deposited on the surface. This space configuration creates a favourable microenvironment for the migration of active hydrogen species (*H). The *H is generated via the activation of H2O on monatomic Pt sites and migrate towards Au clusters with a strong capacity for CO2 adsorption. Under concentrated solar irradiation, selectivity of the (100) facet towards CO is 100 %, and the selectivity of the (110) and (111) facets towards CH4 is 33.5 % and 97.6 %, respectively. Notably, the CH4 yield on the (111) facet is as high as 369.4 µmol/g/h, and the solar-to-chemical energy efficiency of 0.23 % is 33.8 times higher than that under non-concentrated solar irradiation. The impacts of high-density flux photon and thermal effects on carriers and *H migration at the microscale are comprehensively discussed. This study provides a new avenue for tuning the spatial distance between active sites to achieve optimal product selectivity.

Post-synthetic Rhodium (III) Complexes in Covalent Organic Frameworks for Photothermal Heterogeneous C-H Activation.

Although photocatalytic C-H activation has been realized by using heterogeneous catalysts, most of them require high-temperature conditions to provide the energy required for C-H bond breakage. The catalysts with photothermal conversion properties can catalyze this reaction efficiently at room temperature, but so far, these catalysts have been rarely developed. Here, we construct bifunctional catalysts Rh-COF-316 and -318 to combine photosensitive covalent organic frameworks (COFs) and transition-metal catalytic moiety using a post-synthetic approach. The Rh-COF enable the heterogeneous C-H activation reaction by photothermal conversion for the first time, and exhibit excellent yields (up to 98 %) and broad scope of substrates in [4+2] annulation at room temperature, while maintaining the high stability and recyclability. Significantly, this work is the highest yield reported so far in porous materials catalyzing C(sp2)-C(sp2) formation at room temperature. The excellent performances can be attributed to the COF-316, which enhances the photothermal effect (ΔT=50.9 °C), thus accelerating C-H bond activation and the exchange of catalyst with substrates.

Disclosing Support-Size-Dependent Effect on Ambient Light-Driven Photothermal CO2 Hydrogenation over Nickel/Titanium Dioxide.

The size of support in heterogeneous catalysts can strongly affect the catalytic property but is rarely explored in light-driven catalysis. Herein, we demonstrate the size of TiO2 support governs the selectivity in photothermal CO2 hydrogenation by tuning the metal-support interactions (MSI). Small-size TiO2 loading nickel (Ni/TiO2 -25) with enhanced MSI promotes photo-induced electrons of TiO2 migrating to Ni nanoparticles, thus favoring the H2 cleavage and accelerating the CH4 formation (227.7 mmol g-1 h-1 ) under xenon light-induced temperature of 360 °C. Conversely, Ni/TiO2 -100 with large TiO2 prefers yielding CO (94.2 mmol g-1 h-1 ) due to weak MSI, inefficient charge separation, and inadequate supply of activated hydrogen. Under ambient solar irradiation, Ni/TiO2 -25 achieves the optimized CH4 rate (63.0 mmol g-1 h-1 ) with selectivity of 99.8 %, while Ni/TiO2 -100 exhibits the CO selectivity of 90.0 % with rate of 30.0 mmol g-1 h-1 . This work offers a novel approach to tailoring light-driven catalytic properties by support size effect.

Single-Atom Titanium on Mesoporous Nitrogen, Oxygen-Doped Carbon for Efficient Photo-thermal Catalytic CO2 Cycloaddition by a Radical Mechanism.

Developing efficient and earth-abundant catalysts for CO2 fixation to high value-added chemicals is meaningful but challenging. Styrene carbonate has great market value, but the cycloaddition of CO2 to styrene oxide is difficult due to the high steric hindrance and weak electron-withdrawing ability of the phenyl group. To utilize clean energy (such as optical energy) directly and effectively for CO2 value-added process, we introduce earth-abundant Ti single-atom into the mesoporous nitrogen, oxygen-doped carbon nanosheets (Ti-CNO) by a two-step method. The Ti-CNO exhibits excellent photothermal catalytic activities and stability for cycloaddition of CO2 and styrene oxide to styrene carbonate. Under light irradiation and ambient pressure, an optimal Ti-CNO produces styrene carbonate with a yield of 98.3 %, much higher than CN (27.1 %). In addition, it shows remarkable stability during 10 consecutive cycles. Its enhanced catalytic performance stems from the enhanced photothermal effect and improved Lewis acidic/basic sites exposed by the abundant mesopores. The experiments and theoretical simulations demonstrate the styrene oxide⋅+ and CO2⋅- radicals generated at the Lewis acidic (Tiδ+) and basic sites of Ti-CNO under light irradiation, respectively. This work furnishes a strategy for synthesizing advanced single-atom catalysts for photo-thermal synergistic CO2 fixation to high value products via a cycloaddition pathway.

Continuously Flow Photothermal Catalysis Efficiently CO2 Reduction Over S-Scheme 2D/0D Bi5 O7 I-OVs/Cd0.5 Zn0.5 S Heterojunction with Strong Interfacial Electric Field.

Using CO2 , water, and sunlight to produce solar fuel is a very attractive process, which can synchronously reduce carbon and convert solar energy into hydrocarbons. However, photocatalytic CO2 reduction is often limited by the low selectivity of reduction products and poor photocatalytic activity. In this study, S-scheme Bi5 O7 I-OVs/Cd0.5 Zn0.5 S (Bi5 O7 I-OVs/CZS-0.5) heterojunction with strong interfacial electric field (IEF) is prepared by in situ growth method. The performance of reduction CO2 to CO is studied by continuous flow photothermal catalytic (PTC) CO2 reduction platform. 12.5% Bi5 O7 I-OVs/CZS-0.5 shows excellent CO yield of 58.6 µmol g-1  h-1 and selectivity of 98.4%, which are 35.1 times than that of CZS-0.5 under visible light. The charge transfer path of the S-scheme through theoretical calculation (DFT), in situ irradiation Kelvin probe force microscope (ISI-KPFM) and in situ irradiation X-ray photoelectron spectroscopy (ISI-XPS) analysis, is verified. The study can provide useful guidance and reference for improving activity by oxygen vacancy induced strong IEF and the development of a continuous flow PTC CO2 reduction system.

Sunlight-driven CO2utilization over two-dimensional Co-based nanosheets.

Reverse water gas shift (RWGS) reaction is an intriguing strategy to realize carbon neutrality, however, the endothermic process usually needs high temperature that supplied by non-renewable fossil fuels, resulting in secondary energy and environmental issues. Photothermal catalysis are ideal substitutes for the conventional thermal catalysis, providing that high reaction efficiency is achievable. Two-dimensional (2D) materials are highly active as RWGS catalysts, however, their industrial application is restricted by the preparation cost. In this study, a series of 2D Co-based catalysts for photothermal RWGS reaction with tunable selectivity were prepared by self-assembly method based on cheap amylum, by integrating the 2D catalysts with our homemade photothermal device, sunlight driven efficient RWGS reaction was realized. The prepared 2D Co0.5Ce0.5Oxexhibited a full selectivity toward CO (100%) and could be heated to 318 °C under 1 kW m-2irradiation with the CO generation rate of 14.48 mmol g-1h-1, pointing out a cheap and universal method to prepare 2D materials, and zero consumption CO generation from photothermal RWGS reaction.

Superelastic and Photothermal RGO/Zr-Doped TiO2 Nanofibrous Aerogels Enable the Rapid Decomposition of Chemical Warfare Agents.

To date, the reckless use of deadly chemical warfare agents (CWAs) has posed serious risks to humanity, property, and ecological environment. Therefore, necessary materials able to rapidly adsorb and securely decompose these hazardous toxics are in urgent demand. Herein, three-dimensional (3D) reduced graphene oxide/Zr-doped TiO2 nanofibrous aerogels (RGO/ZT NAs) are synthesized by feasibly combining sol-gel electrospinning technology and a unidirectional freeze-drying approach. Benefiting from the synergetic coassembly of flexible ZT nanofibers and pliable RGO nanosheets, the hierarchically entangled fibrous frameworks feature ultralow density, superior elasticity, and robust fatigue resistance over 106 compressive cycles. In particular, the RGO incorporation is attributed to the achieved increased surface area, stronger light absorption, and decreased recombination of charge-carriers for photocatalysis. The highly porous 3D RGO/ZT NAs deliver enhanced photothermal catalytic activity for CWA degradation as well as excellent recyclability and good photostability. This work opens fresh horizons for developing advanced 3D aerogel-based photocatalysts in a controlled fashion.

Strong Metal Support Effect of Pt/g-C3N4 Photocatalysts for Boosting Photothermal Synergistic Degradation of Benzene.

Catalysis is the most efficient and economical method for treating volatile organic pollutants (VOCs). Among the many materials that are used in engineering, platinized carbon nitride (Pt/g-C3N4) is an efficient and multifunctional catalyst which has strong light absorption and mass transfer capabilities, which enable it to be used in photocatalysis, thermal catalysis and photothermal synergistic catalysis for the degradation of benzene. In this work, Pt/g-C3N4 was prepared by four precursors for the photothermal synergistic catalytic degradation of benzene, which show different activities, and many tests were carried out to explore the possible reasons for the discrepancy. Among them, the Pt/g-C3N4 prepared from dicyanamide showed the highest activity and could convert benzene (300 ppm, 20 mL·min-1) completely at 162 °C under solar light and 173 °C under visible light. The reaction temperature was reduced by nearly half compared to the traditional thermal catalytic degradation of benzene at about 300 °C.

Development of Photothermal Catalyst from Biomass Ash (Bagasse) for Hydrogen Production via Dry Reforming of Methane (DRM): An Experimental Study.

Conventional hydrogen production, as an alternative energy resource, has relied on fossil fuels to produce hydrogen, releasing CO2 into the atmosphere. Hydrogen production via the dry forming of methane (DRM) process is a lucrative solution to utilize greenhouse gases, such as carbon dioxide and methane, by using them as raw materials in the DRM process. However, there are a few DRM processing issues, with one being the need to operate at a high temperature to gain high conversion of hydrogen, which is energy intensive. In this study, bagasse ash, which contains a high percentage of silicon dioxide, was designed and modified for catalytic support. Modification of silicon dioxide from bagasse ash was utilized as a waste material, and the performance of bagasse ash-derived catalysts interacting with light irradiation and reducing the amount of energy used in the DRM process was explored. The results showed that the performance of 3%Ni/SiO2 bagasse ash WI was higher than that of 3%Ni/SiO2 commercial SiO2 in terms of the hydrogen product yield, with hydrogen generation initiated in the reaction at 300 °C. Using the same synthesis method, the current results suggested that bagasse ash-derived catalysts had better performance than commercial SiO2-derived catalysts when exposed to an Hg-Xe lamp. This indicated that silicon dioxide from bagasse ash as a catalyst support could help improve the hydrogen yield while lowering the temperature in the DRM reaction, resulting in less energy consumption in hydrogen production.