Highly Flexible and Superelastic Graphene Nanofibrous Aerogels for Intelligent Sign Language.

Highly flexible and superelastic aerogels at large deformation have become urgent mechanical demands in practical uses, but both properties are usually exclusive. Here a trans-scale porosity design is proposed in graphene nanofibrous aerogels (GNFAs) to break the trade-off between high flexibility and superelasticity. The resulting GNFAs can completely recover after 1000 fatigue cycles at 60% folding strain, and notably maintain excellent structural integrity after 10000 cycles at 90% compressive strain, outperforming most of the reported aerogels. The mechanical robustness is demonstrated to be derived from the trans-scale porous structure, which is composed of hyperbolic micropores and porous nanofibers to enable the large elastic deformation capability. It is further revealed that flexible and superelastic GNFAs exhibit high sensitivity and ultrastability as an electrical sensors to detect tension and flexion deformation. As proof, The GNFA sensor is implemented onto a human finger and achieves the intelligent recognition of sign language with high accuracy by multi-layer artificial neural network. This study proposes a highly flexible and elastic graphene aerogel for wearable human-machine interfaces in sensor technology.

A Universal Electronic Structure Modulation Strategy: Is Strong Adsorption Always Correlated with High Catalysis?

Unveiling the inherent link between polysulfide adsorption and catalytic activity is key to achieving optimal performance in Lithium-sulfur (Li-S) batteries. Current research on the sulfur reaction process mainly relies on the strong adsorption of catalysts to confine lithium polysulfides (LiPSs) to the cathode side, effectively suppressing the shuttle effect of polysulfides. However, is strong adsorption always correlated with high catalysis? The inherent relationship between adsorption and catalytic activity remains unclear, limiting the in-depth exploration and rational design of catalysts. Herein, the correlation between "d-band center-adsorption strength-catalytic activity" in porous carbon nanofiber catalysts embedded with different transition metals (M-PCNF-3, M = Fe, Co, Ni, Cu) is systematically investigated, combining the d-band center theory and the Sabatier principle. Theoretical calculations and experimental analysis results indicate that Co-PCNF-3 electrocatalyst with appropriate d-band center positions exhibits moderate adsorption capability and the highest catalytic conversion activity for LiPSs, validating the Sabatier relationship in Li-S battery electrocatalysts. These findings provide indispensable guidelines for the rational design of more durable cathode catalysts for Li-S batteries.

Self-Assembled Preparation of Porous Nickel Phosphide Superparticles with Tunable Phase and Porosity for Efficient Hydrogen Evolution.

Self-assembly of colloidal nanoparticles enables the easy building of assembly units into higher-order structures and the bottom-up preparation of functional materials. Nickel phosphides represent an important group of catalysts for hydrogen evolution reaction (HER) from water splitting. In this paper, the preparation of porous nickel phosphide superparticles and their HER efficiencies are reported. Ni and Ni2P nanoparticles are self-assembled into binary superparticles via an oil-in-water emulsion method. After annealing and acid etching, the as-prepared Ni-Ni2P binary superparticles change into porous nickel phosphide superparticles. The porosity and crystalline phase of the superparticles can be tuned by adjusting the ratio of Ni and Ni2P nanoparticles. The resulting porous superparticles are effective in driving HER under acidic conditions, and the modulation of porosity and phase further optimize the electrochemical performance. The prepared Ni3P porous superparticles not only possess a significantly enhanced specific surface area compared to solid Ni-Ni2P superparticles but also exhibit an excellent HER efficiency. The calculations based on the density functional theories show that the (110) crystal facet exhibits a relatively lower Gibbs free energy of hydrogen adsorption. This work provides a self-assembly approach for the construction of porous metal phosphide nanomaterials with tunable crystalline phase and porosity.

3D Pathways Enabling Highly-Efficient Lithium Reservoir for Fast-Charging Batteries.

Enhancing the mobility of lithium-ions (Li+) through surface engineering is one of major challenges facing fast-charging lithium-ion batteries (LIBs). In case of demanding charging conditions, the use of a conventional artificial graphite (AG) anode leads to an increase in operating temperature and the formation of lithium dendrites on the anode surface. In this study, a biphasic zeolitic imidazolate framework (ZIF)-AG anode, designed strategically and coated with a mesoporous material, is verified to improve the pathways of Li+ and electrons under a high charging current density. In particular, the graphite surface is treated with a coating of a ZIF-8-derived carbon nanoparticles, which addresses sufficient surface porosity, enabling this material to serve as an electrolyte reservoir and facilitate Li+ intercalation. Moreover, the augmentation in specific surface area proves advantageous in reducing the overpotential for interfacial charge transfer reactions. In practical terms, employing a full-cell with the biphasic ZIF-AG anode results in a shorter charging time and improved cycling performance, demonstrating no evidence of Li plating during 300 cycles under 3.0 C-charging and 1.0 C-discharging. The research endeavors to contribute to the progress of anode materials by enhancing their charging capability, aligning with the increasing requirements of the electric vehicle applications.

Layered S-Bridged Covalent Triazine Frameworks via a Bifunctional Template-Catalytic Strategy Enabling High-Performance Zinc-Ion Hybrid Supercapacitors.

Exploring covalent triazine frameworks (CTFs) with high capacitative activity is highly desirable and challenging. Herein, the S-rich CTFs cathode is pioneeringly introduced in Zn-ion hybrid supercapacitors (ZSC), achieving outstanding capacity and energy density, and satisfactory anti-freezing flexibility. Specifically, the S-bridged CTFs are synthesized by a bifunctional template-catalytic strategy, where ZnCl2 serves as both the catalyst/solvent and in situ template to construct triazine frameworks with interconnected pores and layered gaps. The resultant CTFs (CTFS-750) are employed as a reasonable pattern-like system to more deeply scrutinize the synergistic effect of S-bridged triazine and layered porous architecture for polymer-based cathodes in Zn-ion storage. The experimental results indicate that the adsorption barriers of Zn-ions on CTFS-750 are effectively weakened, and accessible Zn2+-absorption sites provided by the C─S─C and C═N bonds have been confirmed via DFT calculations. Consequently, the CTFS-750 cathode-assembled ZSC displays an ultra-high capacity of 211.6 mAh g-1 at 1.0 A g-1, an outstanding energy density of 202.7 Wh kg-1, and attractive cycling performance. Moreover, the resulting flexible ZSC device shows superior capacity, good adaptability, and satisfactory anti-freezing behavior. This approach sheds new light on constructing advanced polymer-based cathodes at the atom level and paves the way for fabricating high-performance ZSC and beyond.

Synergistically Utilizing a Liquid Bridge and Interconnected Porous Superhydrophilic Structures to Achieve a One-Step Fog Collection Mode.

Conventional fog collection efficiency is subject to the inherent inefficiencies of its three constituent steps: fog capture, coalescence, and transportation. This study presents a liquid bridge synergistic fog collection system (LSFCS) by synergistically utilizing a liquid bridge and interconnected porous superhydrophilic structures (IPHS). The results indicate that the introduction of liquid bridge not only greatly accelerates water droplet transportation, but also facilitates the IPHS in maintaining rough structures that realize stable and efficient fog capture. During fog collection, the lower section of the IPHS is covered by a water layer, however due to the effect of the liquid bridge, the upper section protrudes out, while covered by a connective thin water film that does not obscure the microstructures of the upper section. Under these conditions, a one-step fog collection mode is realized. Once captured by the IPHS, fog droplets immediately coalesce with the water film, and are simultaneously transported into a container under the effect of the liquid bridge. The LSFCS achieves a collection efficiency of 6.5 kg m-2 h-1, 2.3 times that of a system without a liquid bridge. This study offers insight on improving fog collection efficiency, and holds promise for condensation water collection or droplet manipulation.

Heat-Localized and Salt-Resistant 3D Hierarchical Porous Ceramic Platform for Efficient Solar-Driven Interfacial Evaporation.

Solar-driven interfacial evaporation (SDIE) is a highly promising approach to achieve sustainable desalination and tackle the global freshwater crisis. Despite advancements in this field, achieving balanced thermal localization and salt resistance remains a challenge. Herein, the study presents a 3D hierarchical porous ceramic platform for SDIE applications. The utilized alumina foam ceramics (AFCs) exhibit remarkable corrosion resistance and chemical stability, ensuring a prolonged operational lifespan in seawater or brines. The millimeter-scale air-filled pores in AFCs prevent thermal losses through conduction with bulk water, resulting in heat-localized interfaces. The hydrophilic nature of macroporous AFC skeletons facilitates rapid water replenishment on the evaporating surface for effective salt-resistant desalination. Benefiting from its self-radiation adsorption and side-assisted evaporation capabilities, the AFC-based evaporators exhibit high indoor evaporation rates of 2.99 and 3.54 kg m-2 h-1 under one-sided and three-sided illumination under 1.0 sun, respectively. The AFC-based evaporator maintains a high evaporation rate of ≈2.77 kg m-2 h-1 throughout the 21-day long-term test. Furthermore, it achieves a daily water productivity of ≈10.44 kg m-2 in outdoor operations. This work demonstrates the potential of 3D hierarchical porous ceramics in addressing the trade-off between heat localization and salt resistance, and contributes to the development of durable solar steam generators.

Modulation of Electronic Synergy to Enhance the Intrinsic Activity of Fe5Ni4S8 Nanosheets in Restricted Space Carbonized Wood Frameworks for Efficient Oxygen Evolution Reaction.

Modulation of electronic structure and composition is widely recognized as an effective strategy to improve electrocatalyst performance. Herein, using a simple simultaneous carbonization and sulfidation strategy, NiFe double hydroxide-derived Fe5Ni4S8 (FNS) nanosheets immobilized on S-doped carbonized wood (SCW) framework by taking benefit of the orientation-constrained cavity and hierarchical porous structure of wood is proposed. Benefiting from the synergistic relationships between bimetal ions, the spatial confinement offered by the wood cavity, and the enhanced structural effects of the nanosheets array, the FNS/SCW exhibit enhanced intrinsic activity, increased accessibility of catalytically active sites, and convection-facilitated mass transport, resulting in an excellent oxygen evolution reaction (OER) activity and durability. Specifically, it takes a low overpotential of 230 mV at 50 mA cm-2 and potential increase is negligible (3.8%) at 50 mA cm-2 for 80 hours. Density functional theory (DFT) calculations further reveal that the synergistic effect of bimetal can optimize the electronic structure and lower the reaction energy barrier. The FNS/SCW used as the cathode of zinc-air battery shows higher power density and excellent durability relative to commercial RuO2, exhibiting a good application prospect. Overall, this research offers proposals for designing and producing effective OER electrocatalysts using sustainable resources.

Lab-on-Device Synthesis of Hierarchical Macro/Mesoporous WO3 Semiconducting Films for High-Performance H2S Sensing.

The performance consistency of the gas sensor is strongly dependent on the interface binding between the sensitive materials and the electrodes. Traditional powder coating methods can inevitably lead to differences in terms of substrate-film interface interaction and device performance, affecting the stability and lifetime. Thus, efficient growth of sensitive materials on device substrates is crucial and essential to enhance the sensing performance, especially for stability. Herein, hierarchically ordered macro/mesoporous WO3 films are in situ synthesized on the electrode via a facile soft/hard dual-template strategy. Orderly arrayed uniform polystyrene (PS) microspheres with tailored size (ca. 1.2 µm) are used as a hard template, and surfactant Pluronic F127 as a soft template can co-assemble with tungsten precursor into ordered mesostructure in the interstitials of PS colloidal crystal induced by solvent evaporation. Benefiting from its rich porosity and high stability, the macro/mesoporous WO3-based sensor shows high sensitivity (Rair/Rgas = 307), fast response/recovery speed (5/9 s), and excellent selectivity (SH2S/Smax > 7) toward 50 ppm H2S gas (a biomarker for halitosis). Significantly, the sensors exhibit an extended service life with a negligible change in sensing performance within 60 days. This lab-on-device synthesis provides a platform method for constructing stable nanodevices with good consistency and high stability, which are highly desired for developing high-performance sensors.

Impact of weak organic acids as coagulants on tailoring the properties of cellulose aerogel beads.

Tailoring the properties of cellulose aerogel beads was investigated in the present study by using weak organic acids as coagulants. Three different weak acids were specifically chosen, acetic acid, lactic acid and citric acid. For comparative studies, a strong acid, hydrochloric acid was examined. The production of aerogel beads by conventional dropping technique was controlled and optimized for weak acids. Aerogels were characterized by density analyses, scanning electron microscopy, nitrogen adsorption-desorption analysis, X-ray powder diffractometry and IR spectroscopy. In common, all the aerogel beads showed interconnected nanofibrillar network, high specific surface area, high pore volume, high porosity and meso- and macroporous structure. In particular, when the weakest acid (acetic acid) was used as coagulant in the regeneration bath, the lowest shrinkage was observed. As a result, the cellulose aerogel beads produced from acetic acid showed the highest values of specific surface area (423 m2·g-1) and pore volume (3.6 cm3·g-1). The porous structure can be tuned by the choice of regeneration bath having either strong acid or high concentration of weak acid. The aerogel beads were pure and showed cellulose II crystallinity. Hence this study paves an alternative path way to tailor the properties of cellulose aerogel beads.

Fabrication of porous poly(L-lactide-co-ε-caprolactone) micropowder for microbubble effect and ultrasound-mediated drug delivery.

Biodegradable elastic poly(L-lactide-co-ε-caprolactone) (PLCL) copolymer (50:50, lactide:caprolactone molar ratio) was synthesized and porous PLCL micropowders was fabricated by a simple method involving rapid cooling of 0.1, 0.5, and 1% (wt/vol) PLCL/dioxane spray into liquid nitrogen. The physicochemical properties of the porous PLCL micropowders were examined by measuring their pore size, pore morphology, and microbead size using a scanning electron microscopy (SEM) and dye and temozolomide (TMZ)-release testing under ultrasound. Human U-87MG, glioblastoma (GBM) cell culture tests were performed to evaluate cell cytotoxicity by released drug from PLCL micropowders. In this study, the porous PLCL micropowders prepared from 1 wt%/vol% PLCL solutions showed a highly porous structure, satisfactory mechanical properties, and optimal drug release efficiency compared with those produced from 0.1 or 0.5 wt%/vol% solutions. The results of the accumulated release test with the results of the absorbance of the dye initially applied, it was confirmed that more than 80% of the added dye was trapped inside the micropowder, and clearly GBM cytotoxicity effect could be observed by the released TMZ. The drug release system using micropowders and ultrasound can be applied as a drug supply system for various diseases such as brain tumors with low drug permeability.

Two-in-one strategy for optimizing chemical and structural properties of carbon felt electrodes for vanadium redox flow batteries.

Vanadium redox flow batteries (VRFBs) have received significant attention for use in large-scale energy storage systems (ESSs) because of their long cycle life, flexible capacity, power design, and safety. However, the poor electrochemical activity of the conventionally used carbon felt electrode results in low energy efficiency of the VRFBs and consequently impedes their commercialization. In this study, a carbon felt (CF) electrode with numerous nanopores and robust oxygen-containing functional groups at its edge sites is designed to improve the electrochemical activity of a carbon felt electrode. To achieve this, Ni metal nanoparticles were initially precipitated on the surface of the CF electrode, followed by etching of the precipitated Ni nanoparticles on the CF electrode using sulfuric acid. The resulting CF electrode had a specific surface area eight times larger than that of the pristine CF electrode. In addition, the oxygen-containing functional groups anchored at the graphite edge sites of the nanopores can act as robust electrocatalysts for VO2+/VO2+ and V2+/V3+ redox reactions. Consequently, the VRFB cell with the resulting carbon felt electrode can deliver a high energy efficiency of 86.2% at the current density of 60 mA cm-2, which is 20% higher than that of the VRFB cell with the conventionally heat-treated CF electrode. Furthermore, the VRFB cell with the resultant carbon felt electrodes showed stable cycling performance with no considerable energy efficiency loss over 200 charge-discharge cycles. In addition, even at a high current density of 160 mA cm-2 , the developed carbon felt electrode can achieve an energy efficiency of 70.1%.

This work reveals the importance of the robust graphite edge-site oxygen functional group and the holey structure of the ET-CF electrode, emphasizing that high VRFB efficiency can be achieved by engineering both the structure and surface properties of the carbon felt electrode.

Enhancing Sensitivity in Gas Detection: Porous Structures in Organic Field-Effect Transistor-Based Sensors.

Gas detection is crucial for detecting environmentally harmful gases. Organic field-effect transistor (OFET)-based gas sensors have attracted attention due to their promising performance and potential for integration into flexible and wearable devices. This review examines the operating mechanisms of OFET-based gas sensors and explores methods for improving sensitivity, with a focus on porous structures. Researchers have achieved significant enhancements in sensor performance by controlling the thickness and free volume of the organic semiconductor layer. Additionally, innovative fabrication techniques like self-assembly and etching have been used to create porous structures, facilitating the diffusion of target gas molecules, and improving sensor response and recovery. These advancements in porous structure fabrication suggest a promising future for OFET-based gas sensors, offering increased sensitivity and selectivity across various applications.

An Ultrasensitive Room-Temperature H2 Sensor Based on a TiO2 Rutile-Anatase Homojunction.

Metal oxide semiconductor hetero- and homojunctions are commonly constructed to improve the performance of hydrogen sensors at room temperature. In this study, a simple two-step hydrothermal method was employed to prepare TiO2 films with homojunctions of rutile and anatase phases (denoted as TiO2-R/A). Then, the microstructure of anatase-phase TiO2 was altered by controlling the amount of hydrochloric acid to realize a more favorable porous structure for charge transport and a larger surface area for contact with H2. The sensor used a Pt interdigital electrode. At an optimal HCl dosage (25 mL), anatase-phase TiO2 uniformly covered rutile-phase TiO2 nanorods, resulting in a greater response to H2 at 2500 ppm compared with that of a rutile TiO2 nanorod sensor by a factor of 1153. The response time was 21 s, mainly because the homojunction formed by the TiO2 rutile and anatase phases increased the synergistic effect of the charge transfer and potential barrier between the two phases, resulting in the formation of more superoxide (O2-) free radicals on the surface. Furthermore, the porous structure increased the surface area for H2 adsorption. The TiO2-R/A-based sensor exhibited high selectivity, long-term stability, and a fast response. This study provides new insights into the design of commercially competitive hydrogen sensors.

Structural Characterization and Physicochemical Properties of Functionally Porous Proton-Exchange Membrane Based on PVDF-SPA Graft Copolymers.

Fluorinated proton-exchange membranes (PEMs) based on graft copolymers of dehydrofluorinated polyvinylidene fluoride (D-PVDF), 3-sulfopropyl acrylate (SPA), and 1H, 1H, 2H-perfluoro-1-hexene (PFH) were prepared via free radical copolymerization and characterized for fuel cell application. The membrane morphology and physical properties were studied via small-(SAXS) and wide-angle X-ray scattering (WAXS), SEM, and DSC. It was found that the crystallinity degree is 17% for PEM-RCF (co-polymer with SPA) and 16% for PEM-RCF-2 (copolymer with SPA and PFH). The designed membranes possess crystallite grains of 5-6 nm in diameter. SEM images reveal a structure with open pores on the surface of diameters from 20 to 140 nm. Their transport and electrochemical characterization shows that the lowest membrane area resistance (0.9 Ωcm2) is comparable to perfluorosulfonic acid PEMs (such as Nafion®) and polyvinylidene fluoride (PVDF) based CJMC cation-exchange membranes (ChemJoy Polymer Materials, China). Key transport and physicochemical properties of new and commercial membranes were compared. The PEM-RCF permeability to NaCl diffusion is rather high, which is due to a relatively low concentration of fixed sulfonate groups. Voltammetry confers that the electrochemical behavior of new PEM correlates to that of commercial cation-exchange membranes, while the ionic conductivity reveals an impact of the extended pores, as in track-etched membranes.

A novel composite electrode with multiple pore structures for efficient treatment of heavy metal ions in capacitive deionization.

Multiple porous carbon materials have great promise and potential in the capacitive deionization (CDI) field. Specific surface area (SSA), pore size distribution, and preparation method of CDI electrode materials are essential for the treatment of heavy metal ions. In this work, PPy composited porous carbon electrodes (hypercrosslinked polymers/polypyrrole, HCPs/PPy) were obtained by one-step crosslinked carbonization preparation and electro-deposition. The diverse pore structure gives the composite electrode a large SSA and excellent adsorption performance. HCPs/PPy-4 gives a high SSA of 251.26 m2/g. In the CDI process, the adsorption capacity of HCPs/PPy-4 for Fe3+, Cu2+, Pb2+, and Ag+ is 20.69 mg/g, 37.81 mg/g, 26.86 mg/g, and 40.95 mg/g. The negative electrode recoveries for the adsorption of the four ions were reached 81.2%, 89.2%, 85.5%, and 100%, respectively. It indicates that HCPs/PPy is a novel and potentially porous carbon electrode for high-performance CDI.

Control of Pore Sizes in Epoxy Monoliths and Applications as Sheet-Type Adhesives in Combination with Conventional Epoxy and Acrylic Adhesives.

Materials with monolithic structures, such as epoxy monoliths, are used for a variety of applications, such as for column fillers in gas chromatography and HPLC, for separators in lithium-ion batteries, and for precursor polymers for monolith adhesion. In this study, we investigated the fabrication of epoxy monoliths using 1,3-bis(N,N-diglycidylaminomethyl)cyclohexane (TETRAD-C) as the tetrafunctional epoxy and 4,4'-methylenebis(cyclohexylamine) (BACM) as the amine curing agent to control pore diameters using polyethylene glycols (PEGs) of differing molecular weights as the porogenic agents. We fabricated an epoxy monolith with micron-order pores and high strength levels, and which is suitable for the precursors of composite materials in cases where smaller PEGs are used. We discussed the effects of the porous structures of monoliths on their physical properties, such as tensile strength, elongation, elastic modulus, and glass transition temperatures. For example, epoxy monoliths prepared in the presence of PEGs exhibited an elastic modulus less than 1 GPa at room temperature and Tg values of 175-187 °C, while the epoxy bulk thermoset produced without any porogenic solvent showed a high elastic modulus as 1.8 GPa, which was maintained at high temperatures, and a high Tg of 223 °C. In addition, the unique adhesion characteristics of epoxy monolith sheets are revealed as a result of the combinations made with commercial epoxy and acrylic adhesives. Epoxy monoliths that are combined with conventional adhesives can function as sheet-type adhesives purposed with avoiding problems when only liquid-type adhesives are used.

Enhanced Adsorption of Trace Ethylene on Ag/NZ5 Modified with Ammonia: Hierarchical Structure and Metal Dispersion Effects.

Trace ethylene poses a significant challenge during the storage and transportation of agricultural products, causing over-ripening, reducing shelf life, and leading to food waste. Zeolite-supported silver adsorbents show promise for efficiently removing trace ethylene. Herein, hierarchical Ag/NZ5(X) adsorbents were prepared via different ammonia modifications, which featured enhanced ethylene adsorption ability. Ag/NZ5(2.5) exhibited the largest capacity and achieved near-complete removal at room temperature with prolonged efficacy. Characterization results indicated that the ammonia modification led to the formation of a hierarchical structure in the zeolite framework, reducing diffusion resistance and increasing the accessibility of the active sites. Additionally, desilication effects increased the defectiveness, generating a stronger metal-support interaction and resulting in a higher metal dispersion rate. These findings provide valuable insights into the development of efficient adsorbents for removing trace ethylene, thereby reducing food waste and extending the shelf life of agricultural products.

Solar-Light-Driven Photocatalytic Oxidative Coupling of Phenol Derivatives over Bismuth-Based Porous Metal Halide Perovskites.

The selective oxidative coupling of phenol derivatives, involving carbon-carbon (C-C) and carbon-oxygen (C-O) bond formation, has emerged as a critical approach in the synthesis of natural products. However, achieving precise control over the selectivity in coupling reactions of unsubstituted phenols utilizing solar light as the driving force remains a big challenge. In this study, we report a series of porous Cs3Bi2X9 (X=Cl, Br, I) photocatalysts with tailored band gaps and compositions engineered for efficient solar-light-driven oxidative phenol coupling. Notably, p-Cs3Bi2Br9 exhibited about 73 % selectivity for C-C coupling, displaying a high formation rate of 47.3 µmol gcat -1 h-1 under solar radiation. Furthermore, this approach enables control of the site-selectivity for phenol derivatives on Cs3Bi2X9, enhancing C-C coupling. The distinctive porous structure and appropriate band-edge positions of Cs3Bi2Br9 facilitated efficient charge separation, and surface interaction/activation of phenolic hydroxyl groups, resulting in the kinetically preferred formation of C-C over C-O bond. Mechanistic insights into the reaction pathway, supported by comprehensive control experiments, unveiled the crucial role of interfacial charge transfers and Lewis acid Bi sites in stabilizing phenolic intermediates, thereby directing the regioselectivity of diradical couplings and resulting in the formation of unsymmetrical biphenols.

[Design and Fabrication of Porous Implants Manufactured by 3D Printing].

Different porous structures were studied through finite element analysis and then optimal porous structure was selected for the orthopedic applications. The optimal Voronoi structure was designed and fabricated using 3D printing. The mechanical properties and osseointegration ability were both investigated. The mechanical tests showed that the tensile strength, compressive strength and bending strength of Voronoi structures were obviously higher than that of the human bone, and the modulus of Voronoi structures were similar to human bone. In addition, the animal experimental results exhibited that obvious bone ingrowth was found from Month 1 to Month 6. This study provides some theoretical references for the orthopedic application of porous structures.