RESUMO
Metal-organic frameworks (MOFs) are believed to be promising precursors for constructing novel and efficient catalysts for glucose sensing. Herein, HKUST-1 precursors are first fabricated using a one-pot hydrothermal approach, and then HKUST-1 is converted into porous Cu2S/CuO octahedrons through conformal sulfidation with the help of OH-ions. The as-obtained Cu2S/CuO composite can provide rich electrochemical active sites and promoted electric transfer kinetics. Benefiting from these combined merits, the as-fabricated Cu2S/CuO composite is confirmed to be a high-performance catalyst, with high sensitivities of 8269.45 and 4140.82µA mM-1cm-2in the corresponding ranges of 0.05 â¼ 0.6 mM and 0.6 â¼ 1.2 mM, respectively. Moreover, the as-prepared electrode materials possess good anti-interference ability, reproducibility and long-term stability. This work opens up new avenues for the design and preparation of transition metal sulfide composites.
RESUMO
WS2 nanotubes present many new technologies under development, including reinforced biocompatible polymers, membranes, photovoltaic-based memories, ferroelectric devices, etc. These technologies depend on the aspect ratio (length/diameter) of the nanotubes, which was limited to 100 or so. A new synthetic technique is presented, resulting in WS2 nanotubes a few hundred micrometers long and diameters below 50 nm (aspect ratios of 2000-5000) in high yields. Preliminary investigation into the mechanistic aspects of the two-step synthesis reveals that W5O14 nanowhisker intermediates are formed in the first step of the reaction instead of the ubiquitous W18O49 nanowhiskers used in the previous syntheses. The electrical and photoluminescence properties of the long nanotubes were studied. WS2 nanotube-based paper-like material was prepared via a wet-laying process, which could not be realized with the 10 µm long WS2 nanotubes. Ultrafiltration of gold nanoparticles using the nanotube-paper membrane was demonstrated.
RESUMO
The Kirazli deposit is located at the center of the Biga Peninsula metallogenic province, in a geological setting characterized by an extensional tectonic environment. A NNW-SSE trending high-sulfidation (HS) orebody with a total reserve of 33.86 Mt @ 0.69 g/t Au and 9.42 g/t Ag lies beneath the Kirazli Main zone. A porphyry Cu orebody hosted by Eocene intrusive and volcanic rocks has been intersected by drilling within its vicinity. The HS epithermal deposit is hosted by a partly silicified and brecciated Oligocene volcanic and volcaniclastic sequence consisting mainly of basaltic andesite lava flow and lithic/crystal tuff. Lithogeochemistry and zircon U-Pb radiometric ages allow us to distinguish three distinct high-K calc-alkaline magmatic events at ca. 41, 38, and 32 Ma, sourced by metasomatized mantle melts, which have interacted with the crust during their ascent. Porphyry Cu mineralization took place at 36.7 ± 0.4 Ma (muscovite 40Ar/39Ar age) with subsequent re-opening and base metal deposition. Crosscutting quartz-pyrite-molybdenite veins were emplaced at 33.6 ± 0.2 Ma (molybdenite Re-Os age), and followed by the HS epithermal Au-Ag event at ca. 31 Ma, based on a previous study. Our radiometric data indicate that the Kirazli deposit has recorded a long-lasting Cenozoic magmatic and metallogenic evolution during about 10 Myr. Our study demonstrates that successive, independent, and overprinting, but genetically unrelated, HS epithermal precious metal, hydrothermal Mo, base metal, and porphyry Cu systems have been active at the same location during protracted extensional tectonics of the Biga Peninsula. Supplementary Information: The online version contains supplementary material available at 10.1007/s00126-023-01235-2.
RESUMO
Thioethers are critical in the fields of pharmaceuticals and organic synthesis, but most of the methods for synthesis alkyl thioethers employ foul-smelling thiols as starting materials or generate them as by-products. Additionally, most thiols are air-sensitive and are easily oxidized to produce disulfides under atmospheric conditions; thus, a novel method for synthesizing thioethers is necessary. This paper reports a simple, effective, green method for synthesizing dialkyl or alkyl aryl thioether derivatives using odorless, stable, low-cost ROCS2K as a thiol surrogate. This transformation offers a broad substrate scope and good functional group tolerance with excellent selectivity. The reaction likely proceeds via xanthate intermediates, which can be readily generated via the nucleophilic substitution of alkyl halides or aryl halides with ROCS2K under transition-metal-free and base-free conditions.
RESUMO
Ultralong nanowires with ultrahigh aspect ratios exhibit high flexibility, and they are promising for applications in various fields. Herein, a cadmium oleate precursor hydrothermal method is developed for the synthesis of ultralong nanowires of cadmium phosphate hydroxide. In this method, water-soluble cadmium salt is used as the cadmium source, water-soluble phosphate is used as the phosphorus source, and sodium oleate is adopted as a reactant to form cadmium oleate precursor and as a structure-directing agent. By using this method, ultralong nanowires of cadmium phosphate hydroxide are successfully synthesized using CdCl2, sodium oleate, and NaH2PO4 as reactants in an aqueous solution by hydrothermal treatment at 180 °C for 24 h. In addition, a new type of flexible fire-resistant inorganic paper with good electrical insulation performance is fabricated using ultralong nanowires of cadmium phosphate hydroxide. As an example of the extended application of this synthetic method, ultralong nanowires of cadmium phosphate hydroxide can be converted to ultralong CdS nanowires through a convenient sulfidation reaction. In this way, ultralong CdS nanowires are successfully synthesized by simple sulfidation of ultralong nanowires of cadmium phosphate hydroxide under mild conditions. The as-prepared ultralong nanowires of cadmium phosphate hydroxide are promising for applications as the precursors and templates for synthesizing other inorganic ultralong nanowires and have wide applications in various fields.
RESUMO
Constructing active heterointerfaces is powerful to enhance the electrochemical performances of transition metal dichalcogenides, but the interface density regulation remains a huge challenge. Herein, MoO2 /MoS2 heterogeneous nanorods are encapsulated in nitrogen and sulfur co-doped carbon matrix (MoO2 /MoS2 @NSC) by controllable sulfidation. MoO2 and MoS2 are coupled intimately at atomic level, forming the MoO2 /MoS2 heterointerfaces with different distribution density. Strong electronic interactions are triggered at these MoO2 /MoS2 heterointerfaces for enhancing electron transfer. In alkaline media, the optimal material exhibits outstanding hydrogen evolution reaction (HER) performances that significantly surpass carbon-covered MoS2 nanorods counterpart (η10 : 156 mV vs 232 mV) and most of the MoS2 -based heterostructures reported recently. First-principles calculation deciphers that MoO2 /MoS2 heterointerfaces greatly promote water dissociation and hydrogen atom adsorption via the O-Mo-S electronic bridges during HER process. Moreover, benefited from the high pseudocapacitance contribution, abundant "ion reservoir"-like channels, and low Na+ diffusion barrier appended by high-density MoO2 /MoS2 heterointerfaces, the material delivers high specific capacity of 888 mAh g-1 , remarkable rate capability and cycling stability of 390 cycles at 0.1 A g-1 as the anode of sodium ion battery. This work will undoubtedly light the way of interface density engineering for high-performance electrochemical energy conversion and storage systems.
RESUMO
Chloroform (CF) is a widely used chemical reagent and disinfectant and a probable human carcinogen. The extensive literature on halocarbon reduction with zerovalent iron (ZVI) shows that transformation of CF is slow, even with nano, bimetallic, sulfidated, and other modified forms of ZVI. In this study, an alternative method of ZVI modificationâinvolving simultaneous sulfidation and nitridation through mechanochemical ball millingâwas developed and shown to give improved degradation of CF (i.e., higher degradation rate and inhibited H2 evolution reaction). The composite material (denoted as S-N(C)-ZVI) gave synergistic effects of nitridation and sulfidation on CF degradation. A complete chemical reaction network (CRN) analysis of CF degradation suggests that O-nucleophile-mediated transformation pathways may be the main route for the formation of the terminal nonchlorinated products (formate, CO, and glycolic polymers) that have been used to explain the undetected products needed for mass balance. Material characterizations of the ZVI recovered after batch experiments showed that sulfidation and nitridation promoted the formation of Fe3O4 on the S-N(C)-ZVI particles, and the effect of aging on CF degradation rates was minor for S-N(C)-ZVI. The synergistic benefits of sulfidation and nitridation on CF degradation were also observed in experiments performed with groundwater.
Assuntos
Água Subterrânea , Poluentes Químicos da Água , Humanos , Ferro/química , Clorofórmio , CinéticaRESUMO
Liquid elemental mercury (Hg0L) pollution can remain in soils for decades and, over time, will undergo corrosion, a process in which the droplet surface oxidizes soil constituents to form more reactive phases, such as mercury oxide (HgO). While these reactive coatings may enhance Hg migration in the subsurface, little is known about the transformation potential of corroded Hg0L in the presence of reduced inorganic sulfur species to form sparingly soluble HgS particles, a process that enables the long-term sequestration of mercury in soils and generally reduces its mobility and bioavailability. In this study, we investigated the dissolution of corroded Hg0L in the presence of sulfide by quantifying rates of aqueous Hg release from corroded Hg0L droplets under different sulfide concentrations (expressed as the S:Hg molar ratio). For droplets corroded in ambient air, no differences in soluble Hg release were observed among all sulfide exposure levels (S:Hg mole ratios ranging from 10-4 to 10). However, for droplets oxidized in the presence of a more reactive oxidant (hydrogen peroxide, H2O2), we observed a 10- to 25-fold increase in dissolved Hg when the oxidized droplets were exposed to low sulfide concentrations (S:Hg ratios from 10-4 to 10-1) relative to droplets exposed to high sulfide concentrations. These results suggest two critical factors that dictate the release of soluble Hg from Hg0L in the presence of sulfide: the extent of surface corrosion of the Hg0L droplet and sufficient sulfide concentration for the formation of HgS solids. The mobilization of Hg0L in porous media, therefore, largely depends on aging conditions in the subsurface and chemical reactivity at the Hg0L droplet interface.
Assuntos
Mercúrio , Mercúrio/análise , Solubilidade , Peróxido de Hidrogênio , Sulfetos , SoloRESUMO
Sulfidation of zerovalent iron (SZVI) can strengthen the decontamination ability by promoting the electron transfer from inner Fe0 to external pollutants by iron sulfide (FeSx). Although FeSx forms easily, the mechanism for the FeSx bonding on the ZVI surface through a liquid precipitation method is elusive. In this work, we demonstrate a key pathway for the sulfidation of ZVI, namely, the in situ formation of FeSx on ZVI surface, which leads to chemical bonding across two domains: the pristine ZVI and the newly formed FeSx phase. The two chemically bridged heterophases display superior activity in electron transportation compared to the physically coated SZVI, eventually bringing about the better performance in reducing Cr(VI) species. It is revealed that the formation of chemically bonded FeSx requires balancing the rates for the two processes of Fe(II) release and sulfidation, which can be achieved by tuning the pH and S(-II) concentration. This study elucidates a mechanism for surface generation of FeSx on ZVI, and it provides new perspectives to design high-quality SZVI for environmental applications.
RESUMO
The effects and mechanisms of zinc oxide nanoparticles (ZnO NPs) and their aging products, sulfidized (s-) ZnO NPs, on the carbon cycling in the legume rhizosphere are still unclear. We observed that, after 30 days of cultivation, in the rhizosphere soil of Medicago truncatula, under ZnO NP and s-ZnO NP treatments, the dissolved organic carbon (DOC) concentrations were significantly increased by 1.8- to 2.4-fold compared to Zn2+ treatments, although the soil organic matter (SOM) contents did not change significantly. Compared to Zn2+ additions, the additions of NPs significantly induced the production of root metabolites such as carboxylic acids and amino acids and also stimulated the growth of microbes involved in the degradations of plant-derived and recalcitrant SOM, such as bacteria genera RB41 and Bryobacter, and fungi genus Conocybe. The bacterial co-occurrence networks indicated that microbes associated with SOM formation and decomposition were significantly increased under NP treatments. The adsorption of NPs by roots, the generation of root metabolites (e.g., carboxylic acid and amino acid), and enrichment of key taxa (e.g., RB41 and Gaiella) were the major mechanisms by which ZnO NPs and s-ZnO NPs drove DOC release and SOM decomposition in the rhizosphere. These results provide new perspectives on the effect of ZnO NPs on agroecosystem functions in soil-plant systems.
Assuntos
Fabaceae , Nanopartículas , Poluentes do Solo , Óxido de Zinco , Fabaceae/metabolismo , Rizosfera , Nanopartículas/química , Plantas/metabolismo , Bactérias/metabolismo , Solo/químicaRESUMO
Iron (oxyhydr)oxides and organic matter (OM) are intimately associated in natural environments, and their fate might be linked to sulfur during sulfidation-reoxidation cycling. However, the coupling of DOM molecular fractionation with Fe and S transformations following a full sulfidation-reoxidation cycle remains poorly understood. Here, we reacted Fh and Fh-OM associations with S(-II) anaerobically and then exposed the sulfidic systems to air. S(-II) preferentially reacted with Fh to form inorganic S (e.g., mackinawite, S0, and S22-) over being incorporated into OM as organic S and therefore indirectly affected OM fate by altering Fe speciation. Fh sulfidation was inhibited by associated OM, and the main secondary Fe species were mackinawite, Fe(II)-OM compounds, and lepidocrocite. Concomitantly, organic molecules high in unsaturation, aromaticity, and molecular weight were detached from solid-phase Fe species due to their lower affinities for secondary Fe species than for Fh. During the reoxidation stage, the previously formed Fe(II) species were reoxidized to Fh with a stronger aggregation, which recaptured formerly released OM with higher selectivity. Additionally, â¢OH was generated from Fe(II) oxygenation and degraded a portion of the DOM molecules. Overall, these results have significant implications for Fe, C, and S cycling in S-rich environments characterized by oscillating redox conditions.
Assuntos
Matéria Orgânica Dissolvida , Ferro , Minerais , Compostos Ferrosos , Compostos Férricos , Enxofre , Oxirredução , SulfetosRESUMO
The association of poorly crystalline iron (hydr)oxides with organic matter (OM), such as extracellular polymeric substances (EPS), exerts a profound effect on Fe and C cycles in soils and sediments, and their behaviors under sulfate-reducing conditions involve complicated mineralogical transformations. However, how different loadings and types of EPS and water chemistry conditions affect the sulfidation still lacks quantitative and systematic investigation. We here synthesized a set of ferrihydrite-organic matter (Fh-OM) coprecipitates with various model compounds for plant and microbial exopolysaccharides (polygalacturonic acids, alginic acid, and xanthan gum) and bacteriogenic EPS (extracted from Bacillus subtilis). Combining wet chemical analysis, X-ray diffraction, and X-ray absorption spectroscopic techniques, we systematically studied the impacts of C and S loadings by tracing the temporal evolution of Fe mineralogy and speciation in aqueous and solid phases. Our results showed that the effect of added OM on sulfidation of Fh-OM coprecipitates is interrelated with the amount of loaded sulfide. Under low sulfide loadings (S(-II)/Fe < 0.5), transformation to goethite and lepidocrocite was the main pathway of ferrihydrite sulfidation, which occurs more strongly at pH 6 compared to that at pH 7.5, and it was promoted and inhibited at low and high C/Fe ratios, respectively. While under high sulfide loadings (S(-II)/Fe > 0.5), the formation of secondary Fe-S minerals such as mackinawite and pyrite dominated ferrihydrite sulfidation, and it was inhibited with increasing C/Fe ratios. Furthermore, all three synthetic EPS proxies unanimously inhibited mineral transformation, while the microbiogenic EPS has a more potent inhibitory effect than synthetic EPS proxies compared at equivalent C/Fe loadings. Collectively, our results suggest that the quantity and chemical characteristics of the associated OM have a strong and nonlinear influence on the extent and pathways of mineralogical transformations of Fh-OM sulfidation.
Assuntos
Carbono , Matriz Extracelular de Substâncias Poliméricas , Oxirredução , Compostos Férricos/química , Minerais/química , Enxofre , ÁguaRESUMO
Chemical sulfidation has been considered as an effective strategy to improve the reactivity of zero-valent iron (S-ZVI). However, sulfidation is a widespread biogeochemical process in nature, which inspired us to explore the biogenetic sulfidation of ZVI (BS-ZVI) with sulfate-reducing bacteria (SRB). BS-ZVI could degrade 96.3% of trichloroethylene (TCE) to acetylene, ethene, ethane, and dichloroethene, comparable to S-ZVI (97.0%) with the same S/Fe ratio (i.e., 0.1). However, S-ZVI (0.21 d-1) exhibited a faster degradation rate than BS-ZVI (0.17 d-1) based on pseudo-first-order kinetic fitting due to extracellular polymeric substances (EPSs) excreted from SRB. Organic components of EPSs, including polysaccharides, humic acid-like substances, and proteins in BS-ZVI, were detected with 3D-EEM spectroscopy and FT-IR analysis. The hemiacetal groups and redox-activated protein in EPS did not affect TCE degradation, while the acetylation degree of EPS increased with the concentration of ZVI and S/Fe, thus inhibiting the TCE degradation. A low concentration of HA-like substances attached to BS-ZVI materials promoted electron transport. However, EPS formed a protective layer on the surface of BS-ZVI materials, reducing its TCE reaction rate. Overall, this study showed a comparable performance enhancement of ZVI toward TCE degradation through biogenetic sulfidation and provided a new alternative method for the sulfidation of ZVI.
Assuntos
Tricloroetileno , Poluentes Químicos da Água , Tricloroetileno/química , Tricloroetileno/metabolismo , Matriz Extracelular de Substâncias Poliméricas/metabolismo , Ferro/química , Espectroscopia de Infravermelho com Transformada de Fourier , Poluentes Químicos da Água/químicaRESUMO
Biogenic sulfidation of zero-valent iron (ZVI) using sulfate reducing bacteria (SRB) has shown enhanced dechlorination rates comparable to those produced by chemical sulfidation. However, controlling and sustaining biogenic sulfidation to enhance in situ dechlorination are poorly understood. Detailed interactions between SRB and ZVI were examined for 4 months in column experiments under enhanced biogenic sulfidation conditions. SRB proliferation and changes in ZVI surface properties were characterized along the flow paths. The results show that ZVI can stimulate SRB activity by removing excessive free sulfide (S2-), in addition to lowering reduction potential. ZVI also hinders downgradient movement of SRB via electrostatic repulsion, restricting SRB presence near the upgradient interface. Dissolved organic carbon (e.g., >2.2 mM) was essential for intense biogenic sulfidation in ZVI columns. The presence of SRB in the upgradient zone appeared to promote the formation of iron polysulfides. Biogenic FeSx deposition increased the S content on ZVI surfaces â¼3-fold, corresponding to 3-fold and 2-fold improvements in the trichloroethylene degradation rate and electron efficiency in batch tests. Elucidation of SRB and ZVI interactions enhances sustained sulfidation in ZVI permeable reactive barrier.
Assuntos
Ferro , Poluentes Químicos da Água , Ferro/química , Poluentes Químicos da Água/química , ElétronsRESUMO
It is of great scientific and practical importance to explore the mechanisms of accelerated degradation of Hexachlorobenzene (HCB) in soil. Both iron oxide and dithionite may promote the reductive dechlorination of HCB, but their effects on the microbial community and the biotic and abiotic mechanisms behind it remain unclear. This study investigated the effects of goethite, dithionite, and their interaction on microbial community composition and structure, and their potential contribution to HCB dechlorination in a paddy soil to reveal the underlying mechanism. The results showed that goethite addition alone did not significantly affect HCB dechlorination because the studied soil lacked iron-reducing bacteria. In contrast, dithionite addition significantly decreased the HCB contents by 44.0-54.9%, while the coexistence of dithionite and goethite further decreased the HCB content by 57.9-69.3%. Random Forest analysis suggested that indicator taxa (Paenibacillus, Acidothermus, Haliagium, G12-WMSP1, and Frankia), Pseudomonas, richness and Shannon's index of microbial community, and immobilized Fe content were dominant driving factors for HCB dechlorination. The dithionite addition, either with or without goethite, accelerated HCB anaerobic dechlorination by increasing microbial diversity and richness as well as the relative abundance of the above specific bacterial genera. When goethite and dithionite coexist, sulfidation of goethite with dithionite could remarkably increase FeS formation and then further promote HCB dechlorination rates. Overall, our results suggested that the combined application of goethite and dithionite could be a practicable strategy for the remediation of HCB contaminated soil.
Assuntos
Poluentes do Solo , Solo , Solo/química , Hexaclorobenzeno , Ditionita/metabolismo , Poluentes do Solo/análise , Bactérias/metabolismoRESUMO
Bismuth telluride-based alloy materials are currently the best performing thermoelectric materials at near room temperature; however, their production and use generate waste (e.g., cutting waste and failed grains). There is also lack of efficient recycling strategies for the generated waste. In this study, a selective sulfidation-vacuum volatilization method is proposed for recovering bismuth telluride waste. The Gibbs free energies of the sulfidation reaction of bismuth telluride are calculated, the saturated vapor pressure of each substance is analyzed, and the composition of the products is predicted. Based on the differences among the sulfidation and volatile properties of bismuth and tellurium, by adding sulfur to bismuth telluride waste, the composition of the substances was regulated, and efficient separation of tellurium and bismuth was achieved. We combined theoretical calculations and experimental studies to investigate the effect of process conditions on the separation and recovery of tellurium and bismuth. The results show that bismuth was thoroughly sulfereted and tellurium was a pure metal when the mass ratio of sulfur to bismuth telluride was 0.168, the sulfidation temperature was 573 K, and the holding time was 60 min. After sulfidation of the bismuth telluride waste, the sulfides were telluride and bismuthous sulfide. The sulfides, that resulted from sulfureted bismuth telluride production, were treated via vacuum volatilization. The optimal vacuum volatilization condition was 873 K for 120 min. The purities of tellurium and bismuth sulfide obtained by the selective sulfidation-vacuum volatilization experiment were >99%. The distribution ratios of tellurium and bismuth were 98.46% and 99.59%, respectively. The method thoroughly separated tellurium and bismuth from bismuth telluride waste, considerably reducing the environmental and economic costs compared with those of the conventional processes.
Assuntos
Bismuto , Telúrio , Vácuo , Volatilização , EnxofreRESUMO
In this study, the biochar (BC) produced from sawdust, sludge, reed and walnut were used to support sulfidation of nano-zero-valent-iron (S-nZVI) to enhance nitrate (NO3--N) removal and investigate the impact on greenhouse gas emissions. Batch experiment results showed the S-nZVI/BCsawdust (2:1, 500), S-nZVI/BCsludge (2:1, 900), S-nZVI/BCreed (2:1, 700), and S-nZVI/BC walnut (2:1, 700) respectively improved NO3--N removal efficiencies by 22%, 20%, 3% and 0.1%, and the selectivity toward N2 by 22%, 25%, 22% and 18%. S-nZVI uniformly loaded on BC provided electrons for the conversion of NO3--N to N2 through Fe0. At the same time, FeSx layer was formed on the outer layer of ZVI in the sulfidation process to prevent iron oxidation, so as to improve the electrons utilization efficiency After adding four kinds of S-nZVI/BC into constructed wetlands (CWs), the NO3--N removal efficiencies could reach 100% and the N2O emission fluxes were reduced by 24.17%-36.63%. And the average removal efficiencies of TN, COD, TP were increased by 21.9%, -16.5%, 44.3%, repectively. The increasing relative abundances of denitrifying bacteria, such as Comamonas and Simplicispira, suggested that S-nZVI/BC could also improve the process of microbial denitrification. In addition, different S-nZVI/BC had different effects on denitrification functional genes (narG, nirk, nirS and nosZ genes), methanotrophs (pmoA) and methanogenesis (mcrA). This research provided an effective method to improve NO3--N removal and reduce N2O emission in CWs.
Assuntos
Gases de Efeito Estufa , Áreas Alagadas , Nitratos , Ferro , Esgotos , Carvão Vegetal , Óxidos de NitrogênioRESUMO
Over 60 years of nuclear activity have resulted in a global legacy of contaminated land and radioactive waste. Uranium (U) is a significant component of this legacy and is present in radioactive wastes and at many contaminated sites. U-incorporated iron (oxyhydr)oxides may provide a long-term barrier to U migration in the environment. However, reductive dissolution of iron (oxyhydr)oxides can occur on reaction with aqueous sulfide (sulfidation), a common environmental species, due to the microbial reduction of sulfate. In this work, U(VI)-goethite was initially reacted with aqueous sulfide, followed by a reoxidation reaction, to further understand the long-term fate of U species under fluctuating environmental conditions. Over the first day of sulfidation, a transient release of aqueous U was observed, likely due to intermediate uranyl(VI)-persulfide species. Despite this, overall U was retained in the solid phase, with the formation of nanocrystalline U(IV)O2 in the sulfidized system along with a persistent U(V) component. On reoxidation, U was associated with an iron (oxyhydr)oxide phase either as an adsorbed uranyl (approximately 65%) or an incorporated U (35%) species. These findings support the overarching concept of iron (oxyhydr)oxides acting as a barrier to U migration in the environment, even under fluctuating redox conditions.
Assuntos
Ferro , Urânio , Ferro/química , Oxirredução , Óxidos , Sulfetos , Urânio/químicaRESUMO
Sulfidation can greatly improve the efficiency of utilization of reducing equivalents for contaminant removal; however, whether this method benefits Fenton-like reactions or not and the possible mechanism are not well understood. In this study, we revealed that surface sulfidation can greatly promote the heterogeneous Fenton activity of ß-FeOOH (Fe3S4@ß-FeOOH) by 40 times, in which not only the â¢OH formation was enhanced but also SO4â¢- as a new oxidation species was generated. Moreover, their contribution to metronidazole (MTZ) degradation was 52.5 and 37.1%, respectively. In comparison, almost no HO2â¢/O2â¢- was detected in the Fe3S4@ß-FeOOH/H2O2 system. These results were different from some previously reported Fenton counterparts. Based on the characterization and probe experiments, sulfur species, including S2-, S0, and Sn2-, as an electron donor and electron shuttle were responsible for efficient conversion of Fe(III) into Fe(II) other than via the Haber-Weiss mechanism, leading to excellent â¢OH generation via a Fenton-like mechanism. Most importantly, HSO5- can be generated from SO32- oxidized by â¢OH, and its scission into SO4â¢- was not dependent on the extra electric potential or Fe-O2-S(IV) intermediate. These findings provided new insight for utilizing sulfidation to improve the activity of iron-based Fenton catalysts.
Assuntos
Compostos Férricos , Peróxido de Hidrogênio , Ferro , Oxirredução , SulfatosRESUMO
2021 marks 10 years since controlled abiotic synthesis of sulfidated nanoscale zerovalent iron (S-nZVI) for use in site remediation and water treatment emerged as an area of active research. It was then expanded to sulfidated microscale ZVI (S-mZVI) and together with S-nZVI, they are collectively referred to as S-(n)ZVI. Heightened interest in S-(n)ZVI stemmed from its significantly higher reactivity to chlorinated solvents and heavy metals. The extremely promising research outcomes during the initial period (2011-2017) led to renewed interest in (n)ZVI-based technologies for water treatment, with an explosion in new research in the last four years (2018-2021) that is building an understanding of the novel and complex role of iron sulfides in enhancing reactivity of (n)ZVI. Numerous studies have focused on exploring different S-(n)ZVI synthesis approaches, and its colloidal, surface, and reactivity (electrochemistry, contaminant selectivity, and corrosion) properties. This review provides a critical overview of the recent milestones in S-(n)ZVI technology development: (i) clear insights into the role of iron sulfides in contaminant transformation and long-term aging, (ii) impact of sulfidation methods and particle characteristics on reactivity, (iii) broader range of treatable contaminants, (iv) synthesis for complete decontamination, (v) ecotoxicity, and (vi) field implementation. In addition, this review discusses major knowledge gaps and future avenues for research opportunities.