Investigation of water and salt flux performances of polyamide coated tubular electrospun nanofiber membrane under pressure.

In this study, a novel osmotic membrane was developed by polyamide (PA) coating on the tubular electrospun nanofiber (TuEN) support membrane. Water and reverse salt flux properties of the obtained membrane were investigated by applying pressure in addition to the osmotic forces. Surface characterization of the membrane was carried out by Fourier-transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM) analyses and flux performance tests were performed in both cross flow and submerged membrane setups. Applying pressure from the feed to the concentrate side had significant effects on the water and salt fluxes. Higher pressure differences between the feed and concentrate sides resulted in unexpected high water fluxes up to 500 Lm-2h-1 (LMH). Besides, the pressure helps to transfer the salt content of feed water into the concentrate side, differently from the osmotic process preventing the salinity build-up at the feed side. PA coated TuEN membrane operated under pressure will exhibit a favorable solution in water/wastewater treatment applications, especially for membrane bioreactors (MBR) in terms of preventing salt accumulation in the bioreactor, decreasing the membrane fouling, increasing the volume of product water, and enabling the concentrate management.

A comparison of different thicknesses of mouthguards according to the groove shape of sheets.

BACKGROUND/AIMS: Previous studies have compared the thickness of the device with and without grooves. The result was a difference in thickness of the device along the groove. The aim of this study was to assess the differences in thickness of mouthguards that result from different groove shapes of ethylene vinyl acetate sheets used to make these appliances. MATERIALS AND METHOD: Mouthguards were made using a 3-dimensional printer, and produced by softening 4 mm transparent circular sheets. Four different shapes of sheets were evaluated: normal sheets, sheets with anterior V-shaped grooves, sheets with anterior A-shaped grooves, and sheets with posterior A-shaped grooves. The groove was 3 mm deep and 5 mm wide. The thickness of the appliance was assessed with respect to the anterior incisal edge, labial surface, palatal surface, posterior cusp, buccal surface, and palatal surface. The Kruskal-Wallis test was used to analyze differences in thickness among the different groove shapes. RESULTS: No significant difference was detected between the thickness of mouthguards made using sheets with grooves and that of mouthguards made using sheets without grooves (P > .05). CONCLUSION: The presence of grooves on the sheets did not influence mouthguard thickness.

Optimal heating condition of mouthguard sheet in vacuum-pressure formation: part 2 Olefin-based thermoplastic elastomer.

The purposes of this study were to clarify the suitable heating conditions during vacuum-pressure formation of olefin copolymer sheets and to examine the sheet temperature at molding and the thickness of the molded mouthguard. Mouthguards were fabricated using 4.0-mm-thick olefin copolymer sheets utilizing a vacuum-pressure forming device, and then, 10 s of vacuum forming and 2 min of compression molding were applied. Three heating conditions were investigated. They were, defined by the degree of sagging observed at the center of the softened sheet (10, 15, or 20 mm lower than the clamp (H-10, H-15, or H-20, respectively)). The working model was trimmed to the height of 20 mm at the maxillary central incisor and 15 mm at the mesiobuccal cusp of the maxillary first molar. The temperature on both the directly heated and the non-heated surfaces of the mouthguard sheet was measured by the radiation thermometer for each condition. The thickness of mouthguard sheets after fabrication was determined for the incisal portion (incisal edge and labial surface) and molar portion (cusp and buccal surface), and dimensional measurements were obtained using a measuring device. Differences in the thickness due to the heating condition of the sheets were analyzed by one-way analysis of variance and Bonferroni's multiple comparison tests. The temperature difference between the heated and non-heated surfaces was highest under H-10. Sheet temperature under H-15 and H-20 was almost the same. The thickness differences were noted at incisal edge, cusp, and buccal surface, and H-15 was the greatest. This study demonstrated that heating of the sheet resulting in sag of 15 mm or more was necessary for sufficient softening of the sheet and that the mouthguard thickness decreased with increased sag. In conclusion, sag of 15 mm can be recommended as a good indicator of appropriate molding timing for this material.

Heating methods for reducing unevenness softening of mouthguard sheets in vacuum-pressure formation.

BACKGROUND: Unevenness in softening of the plastic sheet leads to a decrease in the mouthguard thickness during thermoforming. In this study, we examined the heating methods for reducing unevenness when softening mouthguard sheets during vacuum-pressure formation. MATERIALS AND METHODS: Ethylene vinyl acetate mouthguard sheets and olefin copolymer sheets (thickness: 4.0 mm) were used. The following three heating conditions were compared: condition A-the sheet was molded when it sagged 15 mm from the sheet frame (under normal condition); condition B-the heater was turned off when the sheet sagged by 10 mm from the frame, followed by the sheet molding when the sagging reached 15 mm below the frame; and condition C-the sheet was inverted after heating when the sheet sagged 10 mm and was molded when the sagging reached 15 mm below the frame. The sheet was heated and pressed over the model using a vacuum-pressure machine; then, 10 s of vacuum forming and 2 min of pressure molding were applied. The sheet temperatures were measured using a radiation thermometer. Thickness of the fabricated sheets was determined for the incisal and the molar portion using a measuring device. Thickness data for each condition were analyzed by one-way anova followed by Bonferroni's multiple comparison tests. RESULTS: On both sheets, condition B was smallest for temperature difference between the heated and the non-heated surface, and thicknesses after molding were greatest at all measuring portions. CONCLUSION: By comparing changes in sheet temperatures at molding and variation in thicknesses when applying the heating method using a vacuum-pressure molding machine, we found that reduced unevenness in sheet softening occurred when the heater was turned off when the sag distance of the sheet was 5 mm less than the conventional molding, and then, the sheet was pressed when the conventional sag distance was reached.

Optimal heating condition of mouthguard sheet in vacuum-pressure formation: part 3 styrene-based thermoplastic elastomer.

BACKGROUND: The aim of this study was to identify suitable heating conditions of polyolefin-polystyrene co-polymer sheets in vacuum-pressure formation, monitor the sheet temperature during molding, and examine the thickness of the fabricated mouthguard. MATERIALS AND METHODS: Mouthguards were fabricated with polyolefin-polystyrene co-polymer sheets (4.0-mm thick) utilizing a vacuum/pressure-forming device, which was subjected to vacuum forming for 10 s and pressure molding for 2 min. Four heating conditions were compared, defined by the amount of sag distance of 5, 10, 15, or 20 mm from the center of the softened sheet below the clamp. The working model was trimmed to a height of 20 mm at the cutting edge of the maxillary central incisor and to a height of 15 mm at the mesiobuccal cusp of the maxillary first molar. The radiation thermometer was used to measure the sheet temperatures of the center of the heated and non-heated surfaces under each condition. The sheet thickness after fabrication was determined for the incisal and the molar portions, and dimensional measurements were obtained using a measuring device. The differences in the sheet thickness produced by the different heating conditions were analyzed by Games-Howell's multiple comparison tests. RESULTS: For condition of 5 mm sagged, the temperature on the non-heated surface did not reach a sufficient softening temperature and the thickness was smallest. Mouthguard thickness was largest in the order of 15 mm sagged condition, followed by 20 mm sagged condition and then by 10 mm sagged condition, but a statistical difference was not observed in the labial and the buccal surface among the three conditions. CONCLUSION: This study demonstrated that for sufficient softening, it was necessary to heat the sheet to obtain a sag of 10 mm or more, and that the mouthguard thickness decreased as the sag increased.

Optimal heating condition of ethylene-vinyl acetate co-polymer mouthguard sheet in vacuum-pressure formation.

BACKGROUND: The goal of the present study was to examine the thickness of mouthguards molded under a variety of heating conditions to clarify suitable conditions during vacuum-pressure forming of ethylene vinyl acetate sheets. MATERIALS AND METHODS: Mouthguards were fabricated using ethylene vinyl acetate (EVA) sheets (thickness: 4.0 mm) using a vacuum-pressure forming machine. The sheet was pressed against the working model, followed by vacuum forming for 10 s and compression molding for 2 min. Three heating conditions were investigated in which the sheet was molded when the center of the softened sheet sagged 10 mm, 15 mm, or 20 mm below the clamp (H-10, H-15, or H-20 respectively). The temperature of the sheet surface was measured using a radiation thermometer under each heating condition. The thickness of the mouthguard sheets after fabrication was determined for the incisal portion (incisal edge and labial surface) and molar portion (cusp and buccal surface), and dimensional measurements were obtained using a measuring device. Differences in thickness due to the heating condition of the sheets were analyzed by one-way analysis of variance and Bonferroni's multiple comparison tests. RESULTS: The temperature difference between the heated and non-heated surfaces was lowest under H-15. The thickness differences at incisal edge, labial surface, and cusp were determined. The thicknesses for H-10 and H-15 were greater than that for H-20, and the thicknesses for H-10 and H-15 were equivalent at all measurement points. No differences in thickness at the buccal surface were observed for the various heating conditions. CONCLUSION: The present study demonstrated that a sagging distance of 15 mm provided the most suitable forming process. The results of the present study provide a standard heating condition for EVA sheet forming.

Thickness of mouthguard sheets after vacuum-pressure formation: influence of mouthguard sheet material.

The aim of this study was to investigate the thickness of mouthguard sheet after vacuum-pressure formation based on the mouthguard sheet material. Three mouthguard sheet materials (4.0 mm thick) were compared: ethylene-vinyl acetate co-polymer (EVA), olefin co-polymer (OL), and polyolefin-polystyrene co-polymer (OS). The working model was made by hard gypsum that was trimmed to the height of 20 mm at the cutting edge of the maxillary central incisor and 15 mm at the mesiobuccal cusp of the maxillary first molar. Where the center of the softened sheet sagged 15 mm lower than the clamp, the sheet was pressed against the working model, followed by vacuum forming for 10 s and compression molding for 2 min. The thickness of mouthguard sheets after fabrication was determined for the incisal portion (incisal edge and labial surface) and molar portion (cusp and buccal surface), and dimensional measurements were obtained using a measuring device. Differences in the change in thickness due to sheet materials were analyzed by one-way analysis of variance (anova) followed by Bonferroni's multiple comparison tests. The OL sheet was thickest at all measurement points. At the incisal edge and cusp, thickness after formation was highest for OL, then EVA and finally OS. At the labial surface and buccal surface, the thickness after formation was highest for OL, then OS and finally EVA. This study suggested that post-fabrication mouthguard thickness differed according to sheet material, with the olefin co-polymer sheet having the smallest thickness reduction.

Fluid dynamics and intraocular pressure using venturi phacoemulsification machine in dogs ex vivo.

OBJECTIVE: To optimize fluid dynamics through measuring intraocular pressure (IOP) in a venturi phacoemulsification machine in dogs. PROCEDURES: In step I, flow and IOP of the test chamber were measured using a pressure transducer with the bottle height (BH) set at 50, 70, 100, and 120 cm and the vacuum from 30 to 450 mmHg. A 19-gauge phaco and a 0.3-mm irrigation/aspiration (I/A) handpiece were used. In step II, flow and IOP were measured in an enucleated canine eye with a 3.0- and a 3.2-mm clear corneal incision (CCI), respectively. IOP was measured using the pressure transducer at a 30-mmHg vacuum to allow corneal deformation, to define the fluidic parameters for preventing surge. RESULTS: Flow was directly proportional to the BH and vacuum, whereas IOP was directly proportional to the BH and inversely to the vacuum. Flow with an I/A handpiece was significantly less than with a phaco handpiece, explaining why IOP with an I/A handpiece was significantly higher than with a phaco handpiece. With the I/A handpiece, vacuum parameters less than 450 mmHg did not result in corneal deformation. IOP with a 3.2-mm CCI was significantly lower than with a 3.0-mm CCI, with the 3.2-mm flow being greater than the 3.0-mm flow. CONCLUSIONS: BH during the I/A stage could be reduced to avoid unnecessary stress on the canine eye when using a venturi system. Although phacoemulsification with a 3.2-mm CCI could induce lower IOP, a 3.0-mm CCI might lessen the irrigation flow stress on the eye.

Variations in mouthguard thickness according to fabrication method.

AIM: The purpose of this study was to examine differences in mouthguard thickness according to the method used to form the mouthguard sheet in a combination vacuum-pressure former. MATERIALS AND METHODS: The material used in this study was a mouthguard sheet of 3.8-mm ethylene vinyl acetate. Three forming methods were used: vacuum-forming, vacuum-pressure-forming, and pressure-forming. The sheets were formed when heating causing them to displace 15 mm from baseline. We measured mouthguard thickness at the labial surface of the central incisor, the buccal surface of the first molar, and the occlusal surface of the first molar. Differences in thickness in different regions of mouthguards formed under different conditions were analyzed by two-way analysis of variance and the Bonferroni method. RESULTS: We found that mouthguard thickness differed in different regions of the central incisors and the first molars (P < 0.01). The incisal (cusp) region was thinner than the cervical region. There were significant differences in the thicknesses of vacuum-formed mouthguards and vacuum-pressure-formed mouthguards (P < 0.05), with the vacuum-forming method resulting in thinner guards than the vacuum-pressure-forming method. Mouthguard thickness at the first molar did not differ according to the forming method. CONCLUSIONS: Our results suggest that mouthguard thickness at the anterior teeth varies with different forming methods. This information is important when selecting a mouthguard-forming method.

Impact of Extraction Methods and Transportation Conditions on Lipid Profiles of Bovine Oocytes.

Lipids play numerous pivotal physiological roles in mammalian reproduction, being indispensable for oocyte competence acquisition and post-fertilization embryonic development. Profiling lipids in minute samples, such as oocytes, presents challenges but has been accomplished through mass spectrometry technologies like Multiple Reaction Monitoring (MRM) profiling. With the dual objectives of simplifying workflow and examining the influence of preanalytical conditions, we assessed whether transportation at room temperature affects the lipid profile of bovine oocytes. To this end, samples were prepared using either monophasic (methanol only) or biphasic liquid extraction protocols (Bligh & Dyer method) and transported either on dry ice or at room temperature inside sealed-vacuum packages to prevent lipid oxidation. Subsequently, employing a comprehensive method, we screened a list of 316 MRMs from 10 different lipid subclasses in oocyte lipid extracts. Principal Component Analysis (PCA) revealed similar lipid profiles concerning temperature during transportation, whereas clear differentiation among samples was observed based on the lipid extraction method. Univariate analysis indicated that the one-phase methanol extraction resulted in higher relative abundances of phospholipids, except for phosphatidylserines. Conversely, the Bligh & Dyer extraction favored the detection of neutral intracellular lipids (triacylglycerols, free fatty acids, cholesteryl esters, and acyl-carnitines). Consequently, lipid recovery was directly correlated with the polarity of lipid class and the extraction method. Regarding transportation temperature, phosphatidylethanolamine, triacylglycerol, and free fatty acids exhibited lower abundances when samples were transported at room temperature. Based on multivariate and univariate analyses, we conclude that if samples undergo the same lipid extraction protocol and are transported in the same batch at room temperature inside vacuum-sealed bags, it is feasible to analyze lipid extracts of bovine oocytes and still obtain informative lipid profiling results.

Experimental Investigation on the Energy and Exergy Efficiency of the Vacuum Membrane Distillation System with Its Various Configurations.

This paper addresses a retrofitting vacuum membrane distillation (VMD) setup to reduce the accumulated pressure inside the permeated side. This modification is necessary to extend the operation of the VMD to extreme operation conditions of higher hot water temperatures. This modification, denoted as a hybrid configuration, proposes the injection of a cold water stream into the VMD cell without mixing it with the permeate. Energy and exergy efficiency analyses were performed to assess the effectiveness of the hybrid configuration. The performance of the modified system indicated an improvement in terms of permeate flux (J), the gain output ratio (GOR), and the utilitarian exergetic efficiency (ηex,u), which reach up to two and three times that of the base configuration of the VMD system. However, the exergetic efficiency (ηex) of the hybrid system showed marginal improvement compared to the base case over the tested range of hot water temperatures. This is because the enhanced vapor production is penalized by excess energy consumption. Moreover, the highest exergy destruction percentages occurred in the operational components (e.g., heater and chillers) which fall in the range of 19.0-68.9%. The exergy destruction percentage in the original components (e.g., the VMD cell and condenser) did not exceed 8.3%. Furthermore, this study indicated that the hybrid configuration requires additional tuning and optimization to perform efficiently over wide operating conditions.

Updated review of wet pack complications in pulse vacuum pressure steam sterilisation processes in central sterile supply departments.

The quality of sterilisation and disinfection in a central sterile supply department is directly related to the quality of the hospital services and the patients' safety. Wet packs occasionally occur following the process of pressure steam sterilisation; reducing this occurrence is an important issue. Therefore, the causes of wet pack following sterilisation were analysed to identify the influencing factors and suggest improvements to prevent its occurrence. Understanding the sterilisation process and possible causes of exposure helps with risk assessment and identifying necessary corrective measures.

Comparative analysis of syringes versus pump devices in benchtop aspiration thrombectomy models: A systematic review and meta-analysis.

BACKGROUND: Although direct contact aspiration has emerged as one of the leading techniques for mechanical thrombectomy (MT), there is still ongoing debate about the aspiration/suction pump devices that can optimize recanalization rates. To address this gap, we conducted a meta-analysis comparing the aspiration efficacy of 60 ml syringe and pump devices in benchtop MT models. METHODS: Systematic literature review was conducted using Medline, Embase, Web of Science, and Scopus in accordance with Preferred Reporting Items for Systematic Reviews and Meta-Analysis guidelines. Outcomes of interest included flow rate and vacuum pressure delivered by a 60 ml syringe and several aspiration pumps. We used a random effects model to calculate the mean difference (MD) with 95% confidence intervals (CIs) and a statistically significant difference was considered as a two-sided p-value of less than 0.05. RESULTS: We included six benchtop studies comparing 60 ml syringes and vacuum pumps. Our meta-analysis showed that there were no significant differences in vacuum pressure (MD:0.71inHg, 95% CI: [-0.81;2.23], p = 0.359) and flow rate (MD:0.27 mL/s, 95% CI: [-3,07; 3.61], p = 0.873) between 60 ml syringes and vacuum pumps groups. CONCLUSIONS: Our study demonstrated comparable performance in terms of vacuum pressure and flow rates between a 60 ml syringe and a heterogeneous combination of commercially available aspiration pumps.

Multimodal steerable earthworm-inspired soft robot based on vacuum and positive pressure powered pneumatic actuators.

This article presents a multimodal steerable earthworm-inspired soft robot based on vacuum and positive pressure powered pneumatic actuators capable of crawling both inside pipelines and on planar surfaces. The optimized modular vacuum pressure-driven actuator can generate deformation and anchoring motion through a unified structure under low vacuum pressure, giving it significant speed advantages and multi-modal locomotion capabilities. Meanwhile, the positive pressure powered actuator (PPPA) enables the robot to achieve controlled multi-directional and multi-degrees-of-freedom steering, moreover, enhances the consistency of the driving mechanism. The incorporation of front-end pressure sensing enables the robot to autonomously detect and evaluate pressure, facilitating automatic obstacle avoidance through the activation of corresponding turning units of PPPA. In the process of optimizing motion parameters, the overall motion efficiency has been improved by 16.7% by improving the control law. Through adjustments and optimizations of the interval time (cycle time), the robot is able to achieve a speed of 7.16 mm s-1during planar locomotion and 1.94 mm s-1during in-pipe locomotion. Using the developed robot, we conducted a series of turning experiments, including surface obstacle avoidance and cross-plane crawling, which demonstrated its enhanced capability in cross-plane steering and locomotion. Its related speed indicators showcase superior overall performance compared to other developed robots of the same type.

Investigation on the effect of recasting palladium-silver alloy by argon arc vacuum pressure casting process.

Background/purpose: Palladium-silver (Pd-Ag) alloys are important as an alternative to gold-based alloys. The purpose of this study was to investigate the effect of an argon-arc vacuum pressure casting process on the recasting of the Pd-Ag alloy. Materials and methods: The recasting Pd-Ag alloys were compared with conventional horizontal centrifugal (HC) casting to an argon (Ar)-arc vacuum pressure (Ar-arc/VP) casting. The first-generation castings were made from a Pd-Ag alloy purchased from a supplier. Next-generation castings were made from 50 wt% Pd-Ag alloy before casting and 50 wt% from previous castings. This sequence was repeated over three generations to form the 2nd, 3rd and 4th recasting ingots. The ingots were then measured for marginal accuracy, interfacial oxidation, hardness and phase identification. Results: The recasting success rate of recastibility reached 100%. Compared with the HC group, the Ar-arc/VP group had better edge precision, smaller oxide layer thickness and lower hardness. The comparison of X-ray diffraction intensity showed that the relative intensities of Pd and Ag in the first, second and third generations recasting of the Ar-arc/VP group were significantly higher than those of the HC group. Phase analysis showed that the trace elements of indium and tin contents in the Pd-Ag recasting ingots of the Ar-arc/VP group were higher than those of the HC group. Conclusion: The results showed that the casting process used for recasting affected the quality of the Pd-Ag alloy. Therefore, Ar-arc/VP casting process could improve the effect of Pd-Ag recasting and maintain the alloy properties in comparison with HC casting.

Thermal and Electrical Characterization of Polyester Resins Suitable for Electric Motor Insulation.

This paper undertakes the thermal and electrical characterization of three commercial unsaturated polyester imide resins (UPIR) to identify which among them could better perform the insulation function of electric motors (high-power induction motors fed by pulse-wide modulation (PWM) inverters). The process foreseen for the motor insulation using these resins is Vacuum Pressure Impregnation (VPI). The resin formulations were specially selected because they are one-component systems; hence, before the VPI process, they do not require mixing steps with external hardeners to activate the curing process. Furthermore, they are characterized by low viscosity and a thermal class higher than 180 °C and are Volatile Organic Compound (VOC)-free. Thermal investigations using Thermogravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC) techniques prove their excellent thermal resistance up to 320 °C. Moreover, impedance spectroscopy in the frequency range of 100 Hz-1 MHz was analyzed to compare the electromagnetic performance of the considered formulations. They manifest an electrical conductivity starting from 10-10 S/m, a relative permittivity around 3, and a loss tangent value lower than 0.02, which appears almost stable in the analyzed frequency range. These values confirm their usefulness as impregnating resins in secondary insulation material applications.

Comparison of vacuum pressures and suction forces generated by different pump systems for aspiration thrombectomy.

Objective: Aspiration thrombectomy is used to treat endovascular stroke treatment by clot removal through vacuum and suction forces. We aimed to investigate the pressures and suction forces generated by different pump systems for aspiration. Methods: Vacuum pressure was measured using a vacuum gauge with a closed tip for a 60cc syringe and aspiration pumps. Using an artificial thrombus made from polyvinyl alcohol hydrogel and latex membrane, we assessed the catheter tip force generated on an artificial thrombus using 5Fr Sofia and 6Fr Sofia PLUS intermediate catheters combined with Penumbra Jet Engine or Stryker Medela AXS Universal Aspiration Set. Subsequently, we calculated the catheter tip forces based on the pressure [catheter tip size (force = area × pressure)], and compared with the measured catheter tip force. Results: The 60cc syringe generated the highest vacuum pressure. Among the automatic pumps, the Penumbra jet engine generated the highest vacuum pressure. The catheter tip forces on the artificial thrombus and latex membrane were 18.5 ± 1.70 and 8.0 ± 1.23 gf, respectively, and 13.9 ± 1.37 and 5.6 ± 0.83 gf, respectively using the 5 Fr Sofia with the Penumbra Jet Engine and the Stryker Medela AXS Universal Aspiration Set, respectively. The corresponding values for the 6 Fr Sofia PLUS with the Penumbra Jet Engine and Stryker Medela AXS Universal Aspiration Set were 39.7 ± 3.88 and 20.7 ± 0.92 gf and 25.4 ± 4.96 and 18.0 ± 0.84 gf. For a constant catheter diameter and the automatic pump, the catheter tip force was significantly larger in the artificial thrombus than latex membrane (p < 0.001, ANOVA). Conclusion: The catheter diameter, vacuum pressure, and clot softness are positively correlated with the catheter tip force.

Measurement of Phacoemulsification Vacuum Pressure in the Oertli CataRhex3.

Purpose: To determine the actual vacuum pressure generated by the Oertli CataRhex 3® (Oertli), using an external measuring system. Methods: The effective vacuum pressure created by the Oertli was measured with a pressure device that was continuous with the vacuum tubing system while closed to the external environment. Measurements were taken with the machine set to 300 and 500 mmHg at flow rates of 20, 35, and 50 mL/min and at bottle heights of 60, 80, and 100 cm. Pressures were recorded after the foot pedal was depressed to vacuum setting (second position), and the pressure was allowed to stabilize. Subsequently, it was compared to the pressure value displayed by the machine. Results: Externally measured vacuum pressure was on average 13.02% greater (39.05 mmHg) than displayed vacuum pressure at 300 mmHg (P < 0.005) and 8.60% greater (42.98 mmHg) than displayed vacuum at 500 mmHg (P < 0.005). The average difference between displayed and measured pressure increased with increasing bottle heights. Conclusion: On average, the vacuum pressure generated in the Oertli was found to be significantly higher than the machine's reading when the machine was set at 300 mmHg and 500 mmHg. Adjusting vacuum had variable effects on the measured versus displayed pressure readings.

Enhanced mass transfer of pulsed vacuum pressure pickling and changes in quality of sour bamboo shoots.

Sour bamboo shoot is a traditional Chinese fermented vegetable food. The traditional pickling method of sour bamboo shoots has the disadvantages of being time-consuming, inhomogeneous, and difficult to control. Pulsed vacuum pressure pickling (PVPP) technology uses pulsed vacuum pressure to enhance the pickling efficiency significantly. To demonstrate the effects of salt content and PVPP technical parameters on the fermentation of bamboo shoots, the sample salinity, pH value, color, crunchiness and chewiness, nitrite content, and lactic acid bacteria content during the pickling process were investigated. The salt content inside the bamboo shoots gradually increased to the equilibrium point during the pickling process. The pickling efficiency of bamboo shoots under PVPP technology increased by 34.1% compared to the traditional control groups. Meanwhile, the uniform salt distribution under PVPP technology also obtained better performance in comparison with the traditional groups. The pH value declined slowly from 5.96 to 3.70 with the extension of pickling time and sour flavor accumulated progressively. No significant differences were found in the color values (L *, a *, and b *) and the crunchiness of the bamboo shoot under different salt solution concentrations, vacuum pressure, and pulsation frequency ratio conditions. Colony-forming unit of lactic acid bacteria (CFU of LAB) decreased, to begin with, and then increased until the 6th day, followed by a declining trend in volatility. The nitrate content of bamboo shoots samples under PVPP treatments did not exceed the safety standard (<20 mg/kg) during the whole fermentation process, which proves the safety of PVPP technology. In conclusion, PVPP technology can safely replace the traditional method with better quality performance. The optimal PVPP processing conditions (vacuum pressure 60 kPa, 10 min vacuum pressure time vs. 4 min atmospheric pressure time, salt solution concentration 6%) have been recommended for pickling bamboo shoots with high product quality.

Production and Potential Application of Pyroligneous Acids from Rubberwood and Oil Palm Trunk as Wood Preservatives through Vacuum-Pressure Impregnation Treatment.

The development of low-environmental-impact technologies for the elimination of biological damage is one of the vital goals of the wood protection industry. The possibility of utilizing pyroligneous acid as a wood preservative can be a great solution to extend the application of the currently fast-growing timber species, which has lower natural durability against biological damage. In this study, the effectiveness of pyroligneous acid as a wood preservative was evaluated by impregnating rubberwood with pyroligneous acid using vacuum-pressure treatment, and the treated woods were exposed to mould fungi, wood-decay fungi and termite attacks under laboratory conditions. Pyroligneous acids produced from rubberwood (RWPA) and oil palm trunk (OPTPA) at different pyrolysis temperatures were evaluated. To fully understand the effectiveness of pyroligneous acids as wood preservatives, different concentrations of pyroligneous acids were impregnated into rubberwood. Concentrations of 50% RWPA and 30% OPTPA were sufficient against mould and decay fungi on rubberwood. Rubberwood impregnated with pyroligneous acid acted as a slow-acting toxic bait to cause a high termite mortality rate due to toxic feeding and does not serve as a good repellent to prevent termites from feeding on the wood. In general, OPTPA has better biological durability compared to RWPA.