The Z-Scheme MIL-88B(Fe)/BiOBr Heterojunction Promotes Fe(III)/Fe(II) Cycling and Photocatalytic-Fenton-Like Synergistically Enhances the Degradation of Ciprofloxacin.

The Z-scheme MIL-88B/BiOBr (referred to as MxBy, whereas x and y are the mass of MIL-88B(Fe) and BiOBr) heterojunction photocatalysts are successfully prepared by a facile ball milling method. By adding low concentration H2O2 under visible light irradiation, the Z-scheme heterojunction and photocatalytic-Fenton-like reaction synergistically enhance the degradation and mineralization of ciprofloxacin (CIP). Among them, M50B150 showed efficient photodegradation efficiency and excellent cycling stability, with 94.6% removal of CIP (10 mg L-1) by M50B150 (0.2 g L-1) under 90 min of visible light. In the MxBy heterojunctions, the rapid transfer of photo-generated electrons not only directly decomposed H2O2 to generate ·OH, but also improved the cycle of Fe3+/Fe2+ pairs, which facilitated the reaction with H2O2 to generate ·OH and ·O2 - radicals. In addition, the effects of photocatalyst dosages, pH of CIP solution, and coexisting substances on CIP removal are systematically investigated. It is found that the photocatalytic- Fenton-like reaction can be carried out at a pH close to neutral conditions. Finally, the charge transfer mechanism of the Z-scheme is verified by electron spin resonance (ESR) signals. The ecotoxicity of CIP degradation products is estimated by the T.E.S.T tool, indicating that the constructed photocatalysis-Fenton-like system is a green wastewater treatment technology.

Defect Engineering of Bi2WO6 for Enhanced Photocatalytic Degradation of Antibiotic Pollutants.

Infiltration of excessive antibiotics into aquatic ecosystems plays a significant role in antibiotic resistance, a major global health challenge. It is therefore critical to develop effective technologies for their removal. Herein, defect-rich Bi2WO6 nanoparticles are solvothermally prepared via epitaxial growth on pristine Bi2WO6 seed nanocrystals, and the efficiency of the photocatalytic degradation of ciprofloxacin, a common antibiotic, is found to increase markedly from 62.51% to 98.27% under visible photoirradiation for 60 min. This is due to the formation of a large number of structural defects, where the synergistic interactions between grain boundaries and adjacent dislocations and oxygen vacancies lead to an improved separation and migration efficiency of photogenerated carriers and facilitate the adsorption and degradation of ciprofloxacin, as confirmed in experimental and theoretical studies. Results from this work demonstrate the unique potential of defect engineering for enhanced photocatalytic performance, a critical step in removing antibiotic contaminants in aquatic ecosystems.

Silver ciprofloxacin (CIPAG): a multitargeted metallodrug in the development of breast cancer therapy.

The anti-proliferative activity of the known metalloantibiotic {[Ag(CIPH)2]NO3∙0.75MeOH∙1.2H2O} (CIPAG) (CIPH = ciprofloxacin) against the human breast adenocarcinoma cancer cells MCF-7 (hormone dependent (HD)) and MDA-MB-231 (hormone independent (HI)) is evaluated. The in vitro toxicity and genotoxicity of the metalloantibiotic were estimated toward fetal lung fibroblast (MRC-5) cells. The molecular mechanism of the CIPAG activity against MCF-7 cells was clarified by the (i) cell morphology, (ii) cell cycle arrest, (iii) mitochondrial membrane permeabilization, and (iv) by the assessment of the possible differential effect of CIPAG on estrogen receptor alpha (ERα) and estrogen receptor beta (ERß) transcriptional activation, applying luciferase reporter gene assay. Moreover, the ex vivo mechanism of CIPAG was clarified by its binding affinity toward calf thymus (CT-DNA).

Monolayer Adsorption of Ciprofloxacin on Magnetic Inulin/Mg-Zn-Al Layered Double Hydroxide: Advanced Interpretation of the Adsorption Process.

In this study, magnetic inulin/Mg-Zn-Al layered double hydroxide (MILDH) was synthesized for the adsorption of ciprofloxacin. The application of various analytical techniques confirmed the successful formation of MILDH. For the optimization of controllable factors, Taguchi design was applied and optimum values were obtained as equilibrium time─100 min, adsorbent dose─20 mg, and ciprofloxacin concentration─30 mg/L. The highest capacity of the material was recorded as 196.19 mg/g at 298 K. Langmuir model (R2 = 0.9669-0.9832) fitted best as compared to the Freundlich model (R2 = 0.9588-0.9657), concluded the monolayer adsorption of ciprofloxacin on MILDH. Statistical physics model M 2 was found to fit best to measured data (R2 = 0.9982-0.9989), indicating that the binding of ciprofloxacin took place on two types of receptor sites (n1 and n2). The multidocking mechanism with horizontal position was suggested on the first receptor site (n1 < 1), while multimolecular adsorption of ciprofloxacin lying vertically on the second receptor site (n2 > 1) at all temperatures. The adsorption energies (E1 = 22.79-27.20 kJ/mol; E2 = 18.00-19.46 kJ/mol) illustrated that the adsorption of ciprofloxacin onto MILDH occurred through physical forces. Best fitting of the fractal-like pseudo-first-order kinetic model (R2 = 0.9982-0.9992) indicated that the adsorption of ciprofloxacin happened on the MILDH surface having different energies. X-ray photoelectron spectroscopy analysis further confirmed the adsorption mechanism of ciprofloxacin onto MILDH.

Injectable Modified Sodium Alginate Microspheres for Enhanced Operative Efficiency and Safety in Endoscopic Submucosal Dissection.

Endoscopic submucosal dissection (ESD) is an effective method for resecting early-stage tumors in the digestive system. To achieve a low injection pressure of the injected fluid and continuous elevation of the mucosa following injection during the ESD technique, we introduced an innovative injectable sodium-alginate-based drug-loaded microsphere (Cipro-ThSA) for ESD surgery, which was generated through an emulsion reaction involving cysteine-modified sodium alginate (ThSA) and ciprofloxacin. Cipro-ThSA microspheres exhibited notable adhesiveness, antioxidant activity, and antimicrobial properties, providing a certain level of postoperative wound protection. In vitro cell assays confirmed the decent biocompatibility of the material. Lastly, according to animal experiments involving submucosal elevation of porcine colons, Cipro-ThSA microspheres ensure surgically removable lift height while maintaining the mucosa for approximately 246% longer than saline, which could effectively reduce surgical risks while providing sufficient time for operation. Consequently, the Cipro-ThSA microsphere holds great promise as a novel submucosal injection material, in terms of enhancing the operational safety and effectiveness of ESD surgery.

Magnetically recoverable Ni-doped iron oxide/graphitic carbon nitride nanocomposites for the improved photocatalytic degradation of ciprofloxacin: Investigation of degradation pathways.

Developing efficient and effective photocatalysts is essential for organic dyes and antibiotic degradation in wastewater. Ni-doped α-Fe2O3/g-C3N4 (NFGCN) photocatalysts were synthesised through a simple co-precipitation technique and used for the ciprofloxacin (CIP) and methylene blue (MB) degradation through photocatalysis. The XRD data indicated the crystallinity of the synthesised iron oxide and its composites with rhombohedral structures with the nature of high purity. The morphology of the NFGCN composite revealed the construction of Ni-doped α-Fe2O3 (NFO) nanoparticles onto the g-C3N4 (GCN) sheet surface along with the close interface that induced a Z-scheme heterojunction. The synthesised photocatalysts showed photocatalytic activity with good degradation efficiency of 82.1 % and 92.0 % for CIP and MB, respectively, within 120 min under solar light exposure. The improved photocatalytic degradation efficiency was attained owing to the synthesised composite's enhanced light absorption in the visible range. The narrow band gap energies and interaction between Ni-doped α-Fe2O3 and g-C3N4 displayed by these materials result in enhanced visible light absorption, effective charge carrier separation and transportation to the pollutants. CIP degradation pathways were investigated utilising the LC-MS analysis. NFGCN composites showed good recyclability (5 cycles), magnetic retrievability, and stability for degrading organic and emerging pollutants from wastewater through photocatalysis.

Highly efficient activation of peroxymonosulfate by ZIF-67 anchored cotton derived for ciprofloxacin degradation.

Metal-organic framework (MOF) and MOF-derived materials have attracted extensive research interest as environmental catalysts. In this study, a composite material (ZIF-67/CCot-8) was successfully prepared using cotton fiber as a substrate and growing ZIF-67 in situ. This material exhibited excellent catalytic performance and significantly improved the efficiency of antibiotics degradation. ZIF-67/CCot-8 at a concentration of 0.05 g/L, combined with 0.2 mM peroxymonosulfate (PMS), removed approximately 97% of ciprofloxacin (CIP) and 99% of tetracycline and sulfamethoxazole within 15 min. The high catalytic efficiency of this catalyst is mainly attributed to the uniform distribution of ZIF-67-derived nanoparticles on the surface of the cotton fibers, providing abundant active sites and thereby significantly enhancing the efficiency of antibiotics degradation. Radical quenching experiments and electron paramagnetic resonance (EPR) analyses revealed that sulfate radicals (SO4•-) and singlet oxygen (1O2) were the main active species. Mass spectrometry (MS) was used to elucidate the CIP degradation pathway. The growth of the roots and stems of soybean sprouts in different water environments (tap water, treated water, and untreated water) was also observed. The results demonstrated a significant improvement in the inhibition of plant growth in the post-degradation CIP solution, indicating a substantial reduction in the toxicity of the degraded aqueous solution. To validate the practicality of the ZIF-67/CCot-8/PMS system, a continuous-flow water-treatment device was designed. This system removed 98% of the CIP solution within 180 min, demonstrating its excellent durability. This study presents a potential pathway for effective antibiotics removal using MOF-derived materials.

Synthesis of surficial-modified green biochar catalyst generated by biogas residue biochar and potential application for catalytic ozonation degradation of ciprofloxacin.

This study synthesized novel, green, and easily recoverable surface-modified economical catalysts via hydrothermal treatment (HT) successfully, utilizing biogas residue biochar (BRB), a food waste product from anaerobic fermentation, pyrolyzed at 500 °C for 50 min. Using autoclaves, a total of six solutions were prepared, each having 1 g fine-grinded BRB, surficial modified by adding glycerol (GL) (10 or 20 mL) and SDI water (70 or 60 mL), and heated in an oven at 240 °C, 180 °C, and 120 °C for 24 h. Afterward, the catalysts showed the potential for degradation of widely used emerging pollutants like ciprofloxacin. Taking advantage of catalytic surface modification, the catalytic ozonation degradation was more effective than that of a single ozonation. However, under similar conditions, catalyst amount 0.20 g, ozone dose 15 mg L-1, and ciprofloxacin 80 mg L-1, the performance of the 10 mL GL-180 °C catalyst was excellent. It showed a 92.45%-94.41% optimum removal rate in the 8-10 min interval. After five continuous cycles, the 10 mL GL-180 °C catalyst exhibited excellent stability and reusability. XPS, FT-IR, BET, XRD, and SEM before and after the reaction confirmed the successful synthesis and degradation mechanism. A possible degradation pathway was unrevealed based on a liquid chromatography-mass spectrometer (LC-MS) and scavenger test, proving the significant roles of superoxide radicals (O2•-), hydroxyl radicals (•OH), and singlet oxygen (1O2). Further, Electron paramagnetic resonance (EPR) analysis confirmed the presence of active oxygen species. Subsequently, 10 mL GL-180 °C showed promising degradation for the actual water environment, such as groundwater (73.55%) and river water (64.74%). This work provides a valuable economic strategy to convert biogas residue biochar into a low-cost catalyst for organic pollutant decomposition.

DFT and experimental studies of the facet-dependent oxygen vacancies modulated WS2/BiOCl-OV S-scheme structure for enhanced photocatalytic removal of ciprofloxacin from wastewater.

The present study explores visible light-assisted photodegradation of ciprofloxacin hydrochloride (CIP) antibiotic as a promising solution to water pollution. The focus is on transforming the optical and electronic properties of BiOCl through the generation of oxygen vacancies (OVs) and the exposure of (110) facets, forming a robust S-scheme heterojunction with WS2. The resultant OVs mediated composite with an optimal ratio of WS2 and BiOCl-OV (4-WS2/BiOCl-OV) demonstrated remarkable efficiency (94.3%) in the visible light-assisted photodegradation of CIP antibiotic within 1.5 h. The CIP degradation using 4-WS2/BiOCl-OV followed pseudo-first-order kinetics with the rate constant of 0.023 min-1, outperforming bare WS2, BiOCl, and BiOCl-OV by 8, 6, and 4 times, respectively. Density functional theory (DFT) analysis aligned well with experimental results, providing insights into the structural arrangement and bandgap analysis of the photocatalysts. Liquid chromatography-mass spectrometry (LC-MS) analysis utilized for identifying potentially degraded products while scavenging experiments and electron paramagnetic resonance (EPR) spin trapping analysis elucidated the S-scheme charge transfer mechanism. This research contributes to advancing the design of oxygen vacancy-mediated S-scheme systems in the realm of photocatalysis, with potential implications for addressing water pollution concerns.

From wastewater to clean water: Recent advances on the removal of metronidazole, ciprofloxacin, and sulfamethoxazole antibiotics from water through adsorption and advanced oxidation processes (AOPs).

Antibiotics released into water sources pose significant risks to both human health and the environment. This comprehensive review meticulously examines the ecotoxicological impacts of three prevalent antibiotics-ciprofloxacin, metronidazole, and sulfamethoxazole-on the ecosystems. Within this framework, our primary focus revolves around the key remediation technologies: adsorption and advanced oxidation processes (AOPs). In this context, an array of adsorbents is explored, spanning diverse classes such as biomass-derived biosorbents, graphene-based adsorbents, MXene-based adsorbents, silica gels, carbon nanotubes, carbon-based adsorbents, metal-organic frameworks (MOFs), carbon nanofibers, biochar, metal oxides, and nanocomposites. On the flip side, the review meticulously examines the main AOPs widely employed in water treatment. This includes a thorough analysis of ozonation (O3), the photo-Fenton process, UV/hydrogen peroxide (UV/H2O2), TiO2 photocatalysis, ozone/UV (O3/UV), radiation-induced AOPs, and sonolysis. Furthermore, the review provides in-depth insights into equilibrium isotherm and kinetic models as well as prospects and challenges inherent in these cutting-edge processes. By doing so, this review aims to empower readers with a profound understanding, enabling them to determine research gaps and pioneer innovative treatment methodologies for water contaminated with antibiotics.

Highly adsorptive removal of ciprofloxacin and E. coli inactivation using amino acid tryptophan modified nano-gibbsite.

Adsorption of essential amino acid, Tryptophan (Tryp) on synthesized gibbsite nanoparticles and their applications in eliminating of antibiotic ciprofloxacin (CFX) and bacteria Escherichia coli (E. coli) in aqueous solution. Nano-gibbsite which was successfully fabricated, was characterized by XRD, TEM-SAED, FT-IR, SEM-EDX and zeta potential measurements. The selected parameters for Tryp adsorption on nano-gibbsite to form biomaterial, Tryp/gibbsite were pH 11, gibbsite dosage 20 mg/mL and 1400 mg/L Tryp. The optimum conditions for CFX removal using Tryp/gibbsite were adsorption time 60 min, pH 5, and 20 mg/mL Tryp/gibbsite dosage. The CFX removal significantly raised from 63 to 90% when using Tryp/gibbsite. The Freundlich and pseudo-second-order models achieved the best fits for CFX adsorption isotherm and kinetic on Tryp/gibbsite, respectively. The amount of CFX increased with increasing ionic strength, suggesting that both electrostatic and non-electrostatic interactions were important. After four reused time, CFX removal was greater than 66%, demonstrating that Tryp/gibbsite is reusable with high performance in removing CFX. The application in bacterial activity in term of E. coli reached greater than 98% that was the best material for bacteria inactivation. The present study reveals that Tryp/gibbsite is an excellent bio-material for removing CFX and E. coli.

Construction of carbon quantum dots/riboflavin fluorescent probe and its application in the detection of ciprofloxacin.

The research outlined a novel approach for creating a sensitive and efficient ratio fluorescent probe for ciprofloxacin (CIP) detection. The method used the biomass materials passionfruit shell and diethylenetriamine as carbon and nitrogen sources, respectively, to prepare blue fluorescent carbon quantum dots (b-CQDs) with an average size of 3.29 nm and a quantum yield of 19.6% by a hydrothermal method. The newly designed b-CQDs/riboflavin ratio fluorescent probe demonstrates a distinct advantage for CIP monitoring, exhibiting a marked increase in fluorescence intensity at 445 nm upon interaction with CIP, while maintaining a stable intensity at 510 nm. In the water system, the I445 nm/I510 nm ratio of the fluorescent probe showed a significant linear relationship with CIP at the concentrations of 0-250 µmol·L-1, and the probe boasts a low detection limit of 0.86 µmol·L-1. The outstanding selectivity, broad detection range, low detection limits, and high quantum yield of the b-CQDs highlight their significant potential in the development of advanced sensing probes for efficient detection of ciprofloxacin, offering promising insights for future sensor technology advancements.

Synergistic Inhibitions of Gram-Negative Bacteria by Combination Treatment with Ciprofloxacin and a Novel Glucolipid.

Psychrophilic fungus Pseudogymnoascus sp. OUCMDZ-4032 derived from Antarctica was cultivated under 16 °C to produce a new glucolipid compound (1). Its structure was elucidated by analysis of detailed spectroscopic data, acid hydrolysis and 1-phenyl-3-methyl-5-pyrazolone precolumn derivatization, and 13C NMR quantum chemical calculations. Though compound 1 did not show inhibitory activity against bacteria, it can reduce the minimum inhibitory concentration (MIC) of ciprofloxacin against Gram-negative bacteria Pseudomonas aeruginosa, Escherichia coli, and Salmonella paratyphi by 1024, 256 and 256-fold. Compound 1 showed potential as a synergistically inhibiting adjuvant in co-administration with antibiotic to enhance antibacterial activities.

Enhanced bactericidal, antibiofilm and antioxidative response of Lawsonia inermis leaf extract synthesized ZnO NPs loaded with commercial antibiotic.

Globally, antibiotic resistance is a challenging issue in healthcare sector. The emergence of multiple drug-resistant bacteria has forced us to modify existing medicines and or formulate newer medicines that are effective and inexpensive. In this perspective, this study involves the formation of zinc oxide nanoparticles (ZnO NPs) by utilizing the Lawsonia inermis (Li) leaf extract. The prepared L. inermis leaf extract mediated ZnO NPs (Li-ZnO NPs) were bio-physically characterized. The antibacterial and radical scavenging effects of Li-ZnO NPs were evaluated. In addition, ZnO NPs were conjugated with standard antibiotic (ciprofloxacin) and its drug loading efficiency, drug release and antibacterial efficacy were tested and compared with non-drug loaded ZnO NPs. An absorbance peak at 340 nm was noted for Li-ZnO NPs. After conjugation with the drug, two absorbance peaks- one at 242 nm characteristic of ciprofloxacin and the other at 350 nm characteristics of ZnO NPs were observed. The crystallite size was 18.7 nm as determined by XRD. The antibacterial effect was higher on Gram-positive (S. aureus and S. pyogenes) than the Gram-negative pathogens (E. coli and K. pneumoniae). Inhibition of S. aureus and S. pyogenes biofilm at 100 µg mL-1were, respectively, 97.5 and 92.6%. H2O2 free radicals was inhibited to 90% compared to the standard ascorbic acid at 100 µg mL-1. After drug loading, the FTIR spectrum confirmed the existence of ciprofloxacin peaks at 965 cm-1 and Zn-O bond at 492 cm-1. The drug loading capacity of 15 nm sized ZnO NPs was higher (58, 75, 90 and 95% at 1, 2.5, 5 and 10% drug concentrations, respectively) compared to 20 nm. Similarly, the percentage of drug (ciprofloxacin) released from 15 nm ZnO NPs were increased to 90% at 10% drug-loaded samples, respectively. Also, the antibiotic loaded ZnO NPs had significant antibacterial effects against tested bacteria compared to Li-ZnO NPs and ciprofloxacin alone. This revealed that the antibiotic loaded ZnO NPs offer a sustainable route to treat multi-drug-resistant bacterial infections.

Advancements in Synthetic Strategies and Biological Effects of Ciprofloxacin Derivatives: A Review.

Ciprofloxacin is a widely used antibiotic in the fluoroquinolone class. It is widely acknowledged by various researchers worldwide, and it has been documented to have a broad range of other pharmacological activities, such as anticancer, antiviral, antimalarial activities, etc. Researchers have been exploring the synthesis of ciprofloxacin derivatives with enhanced biological activities or tailored capability to target specific pathogens. The various biological activities of some of the most potent and promising ciprofloxacin derivatives, as well as the synthetic strategies used to develop them, are thoroughly reviewed in this paper. Modification of ciprofloxacin via 4-oxo-3-carboxylic acid resulted in derivatives with reduced efficacy against bacterial strains. Hybrid molecules containing ciprofloxacin scaffolds displayed promising biological effects. The current review paper provides reported findings on the development of novel ciprofloxacin-based molecules with enhanced potency and intended therapeutic activities which will be of great interest to medicinal chemists.

Preparation of mesoporous biogas residue biochar via a self-template strategy for efficient removal of ciprofloxacin: Effect of pyrolysis temperature.

Biochar preparation and application is an anticipated pathway for the resource utilization of biogas residue. In this study, biochars were prepared by the pyrolysis of biogas residue from food waste anaerobic digestion (named as BRBCs) under various pyrolysis temperatures (300, 500, 700, and 900 °C), and the effect of pyrolysis temperatures on the physicochemical characteristics of BRBCs was examined. The adsorption performance toward ciprofloxacin (CIP), a typical antibiotic in waterbodies, was also investigated. The results showed that pyrolysis temperature significantly changed the physicochemical properties of BRBCs. In addition, the minerals in the biogas residue, especially SiO2, were rearranged to form a mesoporous structure in biochar through a self-template strategy (without activator). BRBC prepared at 900 °C exhibited a high specific surface area and pore volume, well-developed mesopore structure, and more carbon structure defects, and exhibited the largest CIP adsorption capacity with 70.29 mg g-1, which was ascribed to the combined interaction of pore diffusion, π-π interactions, hydrogen bonding, complexation, and electrostatic forces. Furthermore, the adsorption of CIP by BRBC900 was well described by two-compartment kinetic and Langmuir isotherm models. BRBC900 showed good adsorption performance toward CIP at pH 7-9. The adsorption of CIP by BRBC is a spontaneous, exothermic, entropy-increasing process. Moreover, BRBC also presented a good recycling potential. Therefore, the preparation of mesoporous biochar based on a self-template strategy not only provides an option for the resource utilization of biogas residue but also offers a new option for the treatment of antibiotic wastewater.

Sorption of ciprofloxacin and enrofloxacin on alkaline cropland soil in semiarid regions: Roles of pH, ionic strength, and ion type.

Animals manure and chemical fertilizers are widely applied to agricultural soils to mitigate soil fertility decline resulting from intensive farming practices. However, the use of antibiotics such as ciprofloxacin (CIP) and enrofloxacin (ENR) in these manures introduces certain environmental risks. The sorption of CIP and ENR in soil is influenced by various factors. Soil cations (i.e., Na+, K+, Mg2+, and Ca2+) and artificially introduced ions (NH4+) can affect the sorption behavior of CIP and ENR in alkaline agricultural soils through mechanisms such as ion exchange and competitive sorption. To investigate the effects of ionic strength and ion type on the sorption of antibiotics in alkaline agricultural soil, batch equilibrium experiments were conducted in this study. The results showed that the affinity of alkaline farmland soil to CIP and ENR was poor, and Kd was only 159 L/kg and 89 L/kg, respectively. Increases in temperature and pH inhibited CIP and ENR sorption on soil. Mineral elements in the soil strongly inhibited CIP and ENR sorption. Conversely, NH4+ promoted the Kd values of CIP and ENR by 46% and 221%, respectively. Additionally, under different influencing factors, both the sorption affinity (Kd) and sorption amount of ENR were lower than those of CIP. These findings indicate that ENR has a greater migration potential and poses a greater environmental risk in agricultural soils. Alkaline soil and mineral elements increase the migration potential of CIP, ENR, but the introduction of NH4+ in agricultural production can weaken the migration potential of them.

Micropollutants (ciprofloxacin and norfloxacin) remediation from wastewater through laccase derived from spent mushroom waste: Fate, toxicity, and degradation.

Fluoroquinolone antibiotics frequently found in environmental matrices (wastewater treatment plants, hospital wastewater, industrial wastewater and surface wastewater) causes potential threat to the environment. Enzymatic treatment for degradation of antibiotics from environmental matrices is a green and sustainable approach. Focusing on this, this study aimed to degrade two frequently found fluroquinolone emergent pollutants, ciprofloxacin and norfloxacin from wastewater. The trinuclear cluster of copper ions present in laccase has the ability to effectively remove organic micropollutants (OMPs). The uniqueness of this study is that it utilizes laccase enzyme extracted from spent mushroom waste (SMW) of P. florida for degradation of ciprofloxacin and norfloxacin and to achieve highest degradation efficiency various parameters were tweaked such as pH (3-6), temperature (30 °C and 50 °C), and ABTS (0.05, 0.6, and 1 mM) concentration. The results showed that the most effective degradation of ciprofloxacin (86.12-75.94%) and norfloxacin (83.27-65.94%) was achieved in 3 h at pH 4.5, temperature 30 °C, and 2,2'-azino-bis 3-ethylbenzothiazoline-6-sulfonic acid (ABTS), 0.05 mM concentration. Nevertheless, achieving degradation at 50 °C for both antibiotics, indicates thermostability nature of laccase (P. florida). Further, the fate of transformed products obtained from laccase mediated degradation was confirmed by liquid chromatography (LC-MS). Both the antibiotics undergo decarboxylation, depiperylyzation, dealkylation and defluorination as a result of laccase-mediated bond breakage. Anti-microbial activity of the biodegraded products was monitored by residual anti-bacterial toxicity test (E. coli and Staphylococcus aureus). The biodegraded products were found to be non-toxic and resulted in the growth of E. coli and Staphylococcus aureus, as determined by the agar-diffusion method. Moreover, the storage stability of laccase was determined for 28-day duration at varying pH (3-10) and temperature (4-50 °C). The maximum storage stability was obtained at pH 4.5 and temperature 30 °C. Therefore, utilizing SMW for the degradation of OMPs from wastewater not only benefits in degradation but also reuses SMW agro waste, shedding light on agro waste management. Thus, SMW is a one-pot solution for both OMPs biodegradation and circularity in the economy.

Ciprofloxacin Removal via Acid-Modified Red Mud: Optimizing the Process, Analyzing the Adsorption Features, and Exploring the Underlying Mechanism.

In this study, RM (red mud) was acidified with sulfuric acid, and the acidified ARM (acidified red mud) was utilized as an innovative adsorption material for treating antibiotic-containing wastewater. The adsorption conditions, kinetics, isotherms, thermodynamics, and mechanism of ARM for CIP (ciprofloxacin) were investigated. The characterization of the ARM involved techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), X-ray fluorescence (XRF), thermogravimetric analysis (TGA), and NH3-TPD analysis. Adsorption studies employed a response surface methodology (RSM) for the experimental design. The results showed that ARM can absorb CIP effectively. The RSM optimal experiment indicated that the most significant model terms influencing adsorption capacity were solution pH, CIP initial concentration, and ARM dosage, under which the predicted maximum adsorption capacity achieved 7.30 mg/g. The adsorption kinetics adhered to a pseudo-second-order model, while equilibrium data fitted the Langmuir-Freundlich isotherm, yielding maximum capacity values of 7.35 mg/g. The adsorption process occurred spontaneously and absorbed heat, evidenced by ΔGθ values between -83.05 and -91.50 kJ/mol, ΔSθ at 281.6 J/mol/K, and ΔHθ at 0.86 kJ/mol. Analysis using attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) indicated a complex reaction between the Al-O in the ARM and the ester group -COO in CIP. The C=O bond in CIP was likely to undergo a slight electrostatic interaction or be bound to the internal spherical surface of the ARM. The findings indicate that ARM is a promising and efficient adsorbent for CIP removal from wastewater.

Synthesis of 2-Ethylhexyl 5-Bromothiophene-2-Carboxylates; Antibacterial Activities against Salmonella Typhi, Validation via Docking Studies, Pharmacokinetics, and Structural Features Determination through DFT.

A new class of thiophene-based molecules of 5-bromothiophene-2-carboxylic acid (1) have been synthesized in current research work. All analogs 4A-4G were synthesized with optimized conditions by coupling reactions of 2-ethylhexyl 5-bromothiophene-2-carboxylate (3) with various arylboronic acids. The results indicated that the majority of compounds showed promising effective in vitro antibacterial activity. Herein, 2-ethylhexyl-5-(p-tolyl)thiophene-2-carboxylate (4F), in particular among the synthesized analogs, showed outstanding antibacterial action (MIC value 3.125 mg/mL) against XDR Salmonella Typhi compared to ciprofloxacin and ceftriaxone. The intermolecular interaction was investigated by using a molecular docking study of thiophene derivatives 4A-4G against XDR S. Typhi. The values of the binding affinity of functionalized thiophene molecules and ciprofloxacin were compared against bacterial enzyme PDB ID: 5ztj. Therefore, 4F appears to be a promising antibacterial agent and showed the highest potential value. Density functional theory (DFT) calculations were executed to examine the electronic, structural, and spectroscopic features of the newly synthesized molecules 4A-4G.