Microleakage of Class II restorations and microtensile bond strength to dentin of low-shrinkage composites.

PURPOSE: To evaluate the microleakage of Class II cavities restored with experimental low-shrinking resin composites proposed for bulk filling and to measure their microtensile bond strength (microTBS) to dentin and compare to those of previously marketed low-shrinkage composites. METHODS: Class II cavities (7 mm occluso-gingival height, 2 mm mesio-distal depth of the box, 4 mm occlusal depth, 4 mm bucco-lingual width) were prepared in 50 molars and randomly divided into five groups (n = 10), according to the material: SureFil SDR flow (SDR), Filtek Silorane (FS) and experimental materials (G-aenial Flo bulk fill, GF; G-aenial Universal Flo bulk fill, GUF; GC Kalore bulk fill, GK). Microleakage was separately assessed at enamel and dentin margins by scoring the depth of silver-nitrate penetration. Twenty teeth divided into five groups (n = 4) were selected for microTBS testing. The same materials as for microleakage assessment were placed in bulk to mid-coronal dentin. Microtensile beams were loaded in tension, and microTBS at failure was calculated in MPa. Microleakage and microTBS data were analyzed by ANOVA on ranks, followed Dunn's post hoc test (P< 0.05). RESULTS: Microleakage was not observed at the enamel interface in any of the groups. At the dentin interface, SDR recorded significantly higher microleakage than the other materials. microTBS of GF, GUF and GK did not differ among each other (33 +/- 12 MPa, 31 +/- 11 MPa, 30 +/- 9 MPa, respectively), while SDR (63 +/- 17 MPa) and FS (55 +/- 17MPa) achieved significantly higher microTBS values. No direct association between the sealing properties and the bond strength values was observed.

Microleakage and penetration of a hydrophilic sealant and a conventional resin-based sealant as a function of preparation techniques: a laboratory study.

BACKGROUND: Optimal pit and fissure sealing is determined by surface preparation techniques and choice of materials. AIM: This study aimed (i) to compare the microleakage and penetration depth of a hydrophilic sealant and a conventional resin-based sealant using one of the following preparation techniques: acid etching (AE) only, a diamond bur + AE, and Er:YAG laser combined with AE, and (ii) to evaluate the microleakage and penetration depth of the hydrophilic pit and fissure sealant on different surface conditions. DESIGN: Eighty recently extracted 3rd molars were randomly assigned to eight groups of ten teeth according to the material, preparation technique, and surface condition. For saliva contamination, 0.1 mL of fresh whole human saliva was used. All samples were submitted to 1000 thermal cycles and immersed in 2% methylene blue dye for 4 h. Sections were examined by a light microscope and analysed using image analysis software (Sigmascan(®)). RESULTS: The combination of Er:YAG + AE + conventional sealant showed the least microleakage. The sealing ability of the hydrophilic sealant was influenced by the surface condition. CONCLUSION: Er:YAG ablation significantly decreased the microleakage at the tooth-sealant interface compared to the non-invasive technique. The hydrophilic sealant applied on different surface conditions showed comparable result to the conventional resin-based sealant.

Effect of prewarming and/or delayed light activation on resin-modified glass ionomer bond strength to tooth structures.

INTRODUCTION: Recent research shows that the acid-base reaction and light-activated polymerization in resin-modified glass ionomers (RMGI) compete with and inhibit one another. In addition, extrinsic energy would improve some properties of RMGI. This in vitro study evaluated the effect of prewarming and/or delayed light activation on bond strength of RMGI to tooth structure. MATERIALS AND METHODS: Ninety-six flat enamel and dentin surfaces of human molars were ground with sequentially finer abrasives to 600-grit silicon carbide paper. Each surface was treated with a cavity conditioner for 10 seconds, rinsed, and gently air-dried (n=12). RMGI was applied to tooth substrates according to the following protocols: group 1) according to manufacturer's instructions; group 2) a delay of two minutes in light activation; group 3) prewarming of the encapsulated material (90 seconds, 40°C); group 4) prewarming plus a delay of two minutes in light activation. After 24 hours of storage at 37°C and 500 rounds of thermocycling, the samples were tested for shear bond strength and analyzed using two-way analysis of variance and Tukey HSD test (α=0.05). RESULTS: Significant differences were observed between study groups (p<0.05). The highest enamel bond strength was recorded in group 2. Regarding dentin groups, the highest bond strength was recorded in group 1. CONCLUSION: Within the limitations of the present study, delaying light activation might improve bond strength of RMGI to enamel; however, the standard procedure recommended by the manufacturer is the best procedure for bonding of RMGI to dentin. More investigations are necessary.

Selective enamel etching: effect on marginal adaptation of self-etch LED-cured bond systems in aged Class I composite restorations.

The aim of this study was to evaluate the influence of previous enamel etch and light emitting diode (LED) curing on gap formation of self-etch adhesive systems in Class I composite restorations after thermomechanical aging (TMA). Thus, on 192 human molars, a box-shaped Class I cavity was prepared maintaining enamel margins. Self-etch adhesives (Clearfil SE and Clearfil S3) were used to restore the preparation with a microhybrid composite. Before application of the adhesives, half of the teeth were enamel etched for 15 seconds with 37% phosphoric acid; the other half were not etched. For the photoactivation of the adhesives and composite, three light-curing units (LCUs) were used: one polywave (Ultra-Lume LED 5, UL) and two single-peak (FlashLite 1401, FL and Radii-cal, RD) LEDs. After this, epoxy resin replicas of the occlusal surface were made, and the specimens were submitted to TMA. New replicas were made from the aged specimens for marginal adaptation analysis by scanning electron microscopy. Data were submitted to Kruskal-Wallis and Wilcoxon tests (α=0.05). Before TMA, when enamel was etched before the application of S3, no gap formation was observed; however, there were gaps at the interface for the other tested conditions, with a statistical difference (p≤0.05). After TMA, the selective enamel etching previous to the S3 application, regardless of the LCU, promoted higher marginal adaptation compared to the other tested groups (p≤0.05). Prior to TMA, higher marginal integrity was observed, in comparison with specimens after TMA (p≤0.05). With regard to Clearfil SE and Clearfil Tri-S cured with FL, no differences of gap formation were found between before and after aging (5.3 ± 3.8 and 7.4 ± 7.5, respectively), especially when the Clearfil Tri-S was used in the conventional protocol. When cured with RD or UL and not etched, Clearfil Tri-S presented the higher gap formation. In conclusion, additional enamel etching promoted better marginal integrity for Clearfil Tri-S, showing it to be an efficient technique for Class I composite restorations. The two-step self-etch adhesive was not influenced by selective enamel etching or by the LED-curing unit.

Real-time enzymatic degradation of human dentin collagen fibrils exposed to exogenous collagenase: an AFM study in situ.

OBJECTIVE: This study was carried out to observe the enzymatic degradation of human dentin collagen fibrils exposed to exogenous collagenase in situ using atomic force microscopy, to understand the characteristics of the enzymatic degradation of collagen fibrils on dentin specimens. METHODS: Polished dentin specimens from caries-free third molars were etched with citric acid, and then treated with an aqueous solution of 6.5% NaOCl for 120 s. The specimen was then put into a fluid cell and treated with a mixed solution of collagenase I (MMP-1) and collagenase II (MMP-8) for 9 h. AFM with contact mode was performed in situ to monitor the enzymatic degradation process of the dentin collagen fibrils. The distinctly topographic changes of the dentin surface were recorded continuously during different stages of the enzymatic degradation process. RESULTS: The mixed solution of exogenous collagenase I and collagenase II could degrade dentin organic matrix (mainly collagen) efficiently, and the structures of dentin substrate were clearly exposed. CONCLUSION: It is possible to carry out real-time observations on the enzymatic biodegradation process of human dentin collagen fibrils on dentin specimens with atomic force microscopy in situ. By this means, the fine structures of the etched dentin substrate were clearly revealed, possibly contributing to the related study of human dentin in vitro.

Characterization of dentine structure in three dimensions using FIB-SEM.

All biological tissues are three dimensional and contain structures that span a range of length scales from nanometres through to hundreds of millimetres. These are not ideally suited to current three-dimensional characterization techniques such as X-ray or transmission electron tomography. Such detailed morphological analysis is critical to understanding the structural features relevant to tissue function and designing therapeutic strategies intended to address structural deficiencies encountered in pathological states. We show that use of focused ion beam milling combined with scanning electron microscopy can provide three-dimensional information at nanometre resolution from biologically relevant volumes of material, in this case dentine.

Effect of erbium:yttrium-aluminum-garnet laser energies on superficial and deep dentin microhardness.

This study evaluated the microhardness of superficial and deep dentin irradiated with different erbium:yttrium-aluminum-garnet (Er:YAG) laser energies. Seventy-two molars were bisected and randomly assigned to two groups (superficial dentin or deep dentin) and into six subgroups (160 mJ, 200 mJ, 260 mJ, 300 mJ, 360 mJ, and control). After irradiation, the cavities were longitudinally bisected. Microhardness was measured at six points (20 microm, 40 microm, 60 microm, 80 microm, 100 microm, and 200 microm) under the cavity floor. Data were submitted to analysis of variance (ANOVA) and Fisher's tests (alpha = 0.05). Superficial dentin presented higher microhardness than deep dentin; energy of 160 mJ resulted in the highest microhardness and 360 mJ the lowest one. Values at all points were different, exhibiting increasing microhardness throughout; superficial dentin microhardness was the highest at 20 microm with 160 mJ energy; for deep dentin, microhardness after irradiation at 160 mJ and 200 mJ was similar to that of the control. The lowest energy increased superficial dentin microhardness at the closest extent under the cavity; deep dentin microhardness was not altered by energies of 160 mJ and 200 mJ.

Remineralising Dentine Caries Using Sodium Fluoride with Silver Nanoparticles: An In Vitro Study.

OBJECTIVE: To investigate the remineralizing and staining effects of sodium fluoride (NaF) solution with polyethylene glycol-coated silver nanoparticles (PEG-AgNPs) on artificial dentine caries. MATERIALS AND METHODS: Demineralized human dentine blocks were allocated to three groups. The blocks in group 1 underwent a topical application of a 12% silver diamine fluoride (SDF, 14,150 ppm fluoride) solution. The blocks in group 2 received a topical application of a 2.5% NaF (11,310 ppm fluoride) with PEG-AgNPs (400 ppm silver). The blocks in group 3 received deionized water. All blocks were subjected to pH cycling for 8 days. The surface morphology and cross-sectional features were investigated using scanning electron microscopy (SEM). The color parameters, crystal characteristics, lesion depth, and collagen degradation of the blocks were assessed using digital spectrophotometry, X-ray diffraction (XRD), micro-computed tomography, and spectrophotometry with a hydroxyproline assay, respectively. RESULTS: The SEM showed that dentine collagen was exposed in group 3 but not in groups 1 and 2. The mean lesion depths in groups 1 to 3 were 118±7 µm, 121±14 µm, and 339±20 µm, respectively (groups1,2<3; p<0.001). The data indicated that fluoridated PEG-AgNPs introduced no significant color effect on dentine, but SDF caused distinct discoloration. The XRD indicated that silver chloride was formed in group 1, and fluorapatite was detected in groups 1 and 2. The concentration of hydroxyproline liberated from collagen was significantly less in groups 1 and 2 than in group 3. CONCLUSION: The use of NaF solution with PEG-AgNPs can remineralize artificial dentine caries and inhibit collagen degradation without causing significant tooth staining.

Comparative cutting effectiveness of an ultrasonic diamond tip and a high-speed diamond bur.

AIM: The aim of this in vitro study was to compare an ultrasonic diamond tip to a high-speed conventional diamond bur regarding the cutting effectiveness in enamel and dentin of human teeth. METHODS: Twenty permanent molars were longitudinally sectioned in the buccal-lingual plane giving 40 specimens, 20 for enamel and 20 for dentin groups. One cavity was performed in each specimen using a spherical diamond tip (83231, CVDentus(R), CVDVale, São José dos Campos, SP, Brazil) coupled with an ultrasound device or a conventional spherical diamond bur (1013, KG Sorensen, São Paulo, Brazil)) coupled with a high-speed turbine. A modified measurement analysis using the Radiocef 4.0 software (Radiocef Memory) was applied to determine the width and the depth of the cavities on scanning electron microscopy (SEM) at x50 magnification micrographs. The features of the cavities and the characteristics of the cutting instruments were also examined under different magnifications by SEM. RESULTS: Statistical analysis by Kruskal-Wallis non-parametric and Dunn post hoc tests (P < or = 0.05) showed that cavities prepared in enamel and dentin with the ultrasonic diamond tip were shallower and narrower than those prepared with conventional diamond bur. The internal walls of cavities prepared in dentin by the ultrasonic diamond tip reproduced the superficial aspect of the diamond, however, scratches were observed in the internal walls of the dentin cut by high-speed conventional diamond bur. CONCLUSIONS: Both instruments were effective in enamel and dentin cutting; however, cavities prepared with a high-speed conventional diamond bur showed more invasive characteristics.

The hidden structure of human enamel.

Enamel is the hardest and most resilient tissue in the human body. Enamel includes morphologically aligned, parallel, ∼50 nm wide, microns-long nanocrystals, bundled either into 5-µm-wide rods or their space-filling interrod. The orientation of enamel crystals, however, is poorly understood. Here we show that the crystalline c-axes are homogenously oriented in interrod crystals across most of the enamel layer thickness. Within each rod crystals are not co-oriented with one another or with the long axis of the rod, as previously assumed: the c-axes of adjacent nanocrystals are most frequently mis-oriented by 1°-30°, and this orientation within each rod gradually changes, with an overall angle spread that is never zero, but varies between 30°-90° within one rod. Molecular dynamics simulations demonstrate that the observed mis-orientations of adjacent crystals induce crack deflection. This toughening mechanism contributes to the unique resilience of enamel, which lasts a lifetime under extreme physical and chemical challenges.

Three-Dimensional Assessment of Crown Size and Eruption Space for Developing Third Molars: Data Collection Techniques Based on Cone-Beam Computed Tomography (CBCT).

Third molar development and eruption are two related areas of major interest in dental research into the etiology of "wisdom tooth" impaction. Third molars are not only an excellent model for studying dental development but also of fundamental clinical importance because they are very frequently impacted. Because the third molar is located in the distal-most region of the oral cavity, clinical access is relatively challenging. With the increasingly widespread use of cone-beam computed tomography (CBCT) in dentistry, studies and measurements of the third molar and its eruption area have become considerably easier to do. Here we present a novel CBCT-based measurement methodology we developed for our recent investigations that we hope will also be useful for the broader dental research community.

Guided tissue remineralisation of partially demineralised human dentine.

Biomineralisation is a well-regulated process mediated by extracellular matrix proteins. Biomimetic remineralisation strategies should reproduce the dimension and structural hierarchy of apatite deposits within a demineralised collagen matrix. Interfibrillar and intrafibrillar remineralisation of phosphoric acid-etched human dentine was demonstrated in this study using a Portland cement/phosphate-containing fluid system in the presence of polyacrylic acid and polyvinylphosphonic acid as respective calcium phosphate- and collagen-binding matrix protein analogues. Metastable amorphous calcium phosphate nanoprecursors were generated when polyacrylic acid was included in the phosphate-containing fluid. When both polyvinylphosphonic acid and polyacrylic acid were included, these nanoprecursors were attracted to the acid-demineralised collagen matrix and transformed into polyelectrolyte-stabilised apatite nanocrystals that assembled along the microfibrils (intrafibrillar remineralisation) and surface of the collagen fibrils (interfibrillar remineralisation). Transition from nanocrystals to larger apatite platelets probably occurred via the formation of mesocrystal intermediates. Guided tissue remineralisation is potentially useful in the remineralisation of acid-etched dentine that is incompletely infiltrated by dentine adhesives, as well as partially demineralised caries-affected dentine.

SEM analysis of enamel surface treated by Er:YAG laser: influence of irradiation distance.

BACKGROUND: Depending on the distance of laser tip to dental surface a specific morphological pattern should be expected. However, there have been limited reports that correlate the Er:YAG irradiation distance with dental morphology. PURPOSE: To assess the influence of Er:YAG laser irradiation distance on enamel morphology, by means of scanning electron microscopy (SEM). METHODS: Sixty human third molars were employed to obtain discs (approximately =1 mm thick) that were randomly assigned to six groups (n=10). Five groups received Er:YAG laser irradiation (80 mJ/2 Hz) for 20 s, according to the irradiation distance: 11, 12, 14, 16, or 17 mm and the control group was treated with 37% phosphoric acid for 15 s. The laser-irradiated discs were bisected. One hemi-disc was separated for superficial analysis without subsequent acid etching, and the other one, received the phosphoric acid for 15 s. Samples were prepared for SEM. RESULTS: Laser irradiation at 11 and 12 mm provided an evident ablation of enamel, with evident fissures and some fused areas. At 14, 16 and 17 mm the superficial topography was flatter than in the other distances. The subsequent acid etching on the lased-surface partially removed the disorganized tissue. CONCLUSIONS: Er:YAG laser in defocused mode promoted slight morphological alterations and seems more suitable for enamel conditioning than focused irradiation. The application of phosphoric acid on lased-enamel surface, regardless of the irradiation distance, decreased the superficial irregularities.

Sealing ability of occlusal resin composite restoration using four restorative procedures.

The purpose of this work was to investigate fluid flow after restoration using four restorative procedures. Micro-gap, internal dye leakage, and micropermeability of bonded interfaces were also investigated. Each tooth was mounted, connected to a fluid flow-measuring device, and an occlusal cavity was prepared. Fluid flow after cavity preparation was recorded as the baseline measurement, and the cavity was restored using one of four restorative procedures: bonding with total-etch (Single Bond 2) or self-etch (Clearfil SE Bond) adhesives without lining; or lining with resin-modified glass-ionomer cement (GIC) (Fuji Lining LC) or conventional GIC (Fuji IX) and then bonding with the total-etch adhesive. Fluid flow was recorded after restoration and at specific time-points up to 6 months thereafter and recorded as a percentage. Micro-gap formation was analyzed using resin replicas and scanning electron microscopy. Internal leakage of 2% methylene blue dye was observed under a light microscope. In micro-permeability testing, fluorescent-dye penetration was investigated using confocal laser microscopy. None of the restorative procedures provided a perfectly sealed restoration. Glass-ionomer lining did not reduce fluid flow after restoration, and micro-gaps were frequently detected. The self-etch adhesive failed to provide a better seal than the total-etch adhesive, and even initial gap formation was rarely observed for the former. Penetration of methylene blue and fluorescent dyes was detected in most restorations.

High-resolution non-destructive 3D interrogation of dentin using X-ray nanotomography.

OBJECTIVES: Dentin, a calcareous material sandwiched between the pulp and the enamel in the tooth structure contains highly orientated tubules. As a result of enamel erosion, gum recession, physical trauma or caries the dentin tubules can become patent to the oral cavity. It has been demonstrated in vivo that dentinal fluid flows out of the tubule lumen into the oral cavity and it has been postulated that alterations in fluid flow form the basis of dentin hypersensitivity. In order to better understand the mode of action of desensitising occlusion-based agents the ability to interrogate dentin non-destructively is paramount. Destructive analysis of the tooth structure may yield subtle artifacts leading to erroneous conclusions or inhibit the accurate assessment of the relationship between an occluding agent and the internal dentin morphology. This paper describes the use of a novel and accessible, non-invasive, high-focused X-ray computer tomographic technique for analysis of the dentin substructure. METHODS: Dentin slices, ca. 300microm3 in size, were taken from the coronal section of unerupted human third molars and etched in citric acid to reveal the open tubule structure. Samples were analyzed, in their dry state, using the Skyscan 2011 nanoCT system. RESULTS: Numerous, homogeneously dispersed elliptical features, distinguished by their contrast and hence low-mineral density, were observed. These features are observed to be approximately 2-5microm in diameter at a density equivalent to 10(6)cm(-2). 2D CT re-slices demonstrate that these circular features form highly orientated cylindrical manifestations extending throughout the sample. SIGNIFICANCE: Ultra-high-resolution X-ray computed tomography has been shown to be a powerful new technique for interrogating the submicron tubular structure of dentin non-destructively.

Immunohistochemical localization of dentin matrix protein 1 in human dentin.

Dentin matrix protein 1 (DMP1) is a non-collagenous matrix protein with a recognized role in the formation of mineralized tissues such as dentin. The aim of this study was to analyze the distribution of DMP1 in human dentin by means of immunofluorescence and high-resolution immunogold labeling. Fully developed, sound human dentin specimens were submitted to fluorescence labeling and post-embedding immunolabeling techniques with a rabbit polyclonal antihuman DMP1 antibody followed by corresponding fluorochrome-conjugated or gold-conjugated secondary antibodies. Both immunofluorescence and immunogold labeling showed an intense labeling associated with the peritubular dentin. In addition, at the ultrastructural level, there was also a moderate and diffuse immunoreaction over intertubular dentin, and a weak labeling within predentin which increased in density towards the mineralization front. This study suggests that in adult human teeth, like in rodents, DMP1 is prevalently concentrated at the level of peritubular dentin and this feature is preserved also in fully developed-teeth. These data are consistent with what has been observed in rodents and suggest that DMP1 plays a role in maintenance of the dentin tubular space.

Correlations between AFM and SEM imaging of acid-etched tooth enamel.

Enamel bond strength is an important factor in restorative dentistry and crucially depends on the enamel roughness. To increase roughness, different etching procedures are employed and profilometric estimations, with probe profilometers, including atomic force microscopy (AFM), have been made. However, no correlation between roughness and bond strength has been found. To search for a possible error source leading to the underestimation of enamel roughness when utilizing probe profilometers, the authors compared scanning electron microscopy and AFM images of acid-etched tooth enamel. The results showed that AFM imaging cannot correctly depict the acid-etched enamel surface, because of the high steepness of the enamel crystallites and the generation of convolute images. This leads to a large underestimation of the profilometric parameters measured with AFM, or other profilometers, on acid-etched tooth enamel surfaces.

Effect of two in-office whitening agents on the enamel surface in vivo: a morphological and non-contact profilometric study.

This study evaluated the morphological effects produced in vivo by two in-office bleaching agents on enamel surface roughness using a noncontact profilometric analysis of epoxy replicas. The null hypothesis tested was that there would be no difference in the micromorphology of the enamel surface during or after bleaching with two different bleaching agents. Eighteen subjects were selected and randomly assigned to two treatment groups (n=9). The tooth whitening materials tested were 38% hydrogen peroxide (HP) (Opalescence Xtra Boost) and 35% carbamide peroxide (CP) (Rembrandt Quik Start). The bleaching agents were applied in accordance with manufacturer protocols. The treatments were repeated four times at one-week intervals. High precision impressions of the upper right incisor were taken at baseline as the control (CTRL) and after each bleaching treatment (T0: first application, T1: second application at one week, T2: third application at two weeks and T3: fourth application at three weeks). Epoxy resin replicas were poured from impressions, and the surface roughness was analyzed by means of a non-contact profilometer (Talysurf CLI 1000). Epoxy replicas were then observed using SEM. All data were statistically analyzed using ANOVA and differences were determined with a t-test. No significant differences in surface roughness were found on enamel replicas using either 38% hydrogen peroxide or 35% carbamide peroxide in vivo. This in vivo study supports the null hypothesis that two in-office bleaching agents, with either a high concentration of hydrogen or carbamide peroxide, do not alter enamel surface roughness, even after multiple applications.

Aspects of the final phase of enamel formation as evidenced by observations of superficial enamel of human third molars using scanning electron microscopy.

OBJECTIVE: Enamel structure reflects ameloblast function. By studying the structure of the superficial enamel, information about ameloblast function toward the end of the secretory stage may be obtained. DESIGN: The superficial enamel in midcoronal areas of acid-etched facio-lingual sections from human third molars was studied in the scanning electron microscope (SEM). RESULTS: A great variation was observed in occurrence of prism-free enamel. Prism-free enamel dominated in 40% (mandibular) and 47% (maxillary) of observed areas and had a mean thickness of about 30µm. Striations in the prism-free enamel had an interstriae distance of about 3.3-3.8µm. The angle between prisms and enamel surface was about 60°, between prisms and Retzius lines about 45° and between Retzius lines and enamel surface about 15°. The distances between regularly occurring Retzius lines and between striations in the prism-free enamel both tended to decrease toward the enamel surface. Prisms could change direction as they approached the enamel surface, mostly in cervical direction. Where Retzius lines curved and converged occlusally, prisms tended to deviate in an occlusal direction. CONCLUSIONS: Judged from the incremental lines and occurrence of prism-free enamel, ameloblasts slow down and tend to lose their Tomes' process as they approach the end of secretion. The crystals of prism-free enamel belong to the same system as the interprism crystals of prismatic enamel. A method, based on the disposition of fine incremental lines, is suggested for evaluation of ameloblast dynamics in the last stage of enamel secretion.

Mapping the mechanical gradient of human dentin-enamel-junction at different intratooth locations.

OBJECTIVES: The local structures and mechanical properties within tooth dentin-enamel-junction (DEJ) regions have been focused for numerous studies. The reported results, however, remain inconsistent particularly on the functional width and gradient architecture of the DEJ. The current study aims at systematically determining the mechanical gradient of the DEJ at different intratooth locations such that a clearer understanding on the tooth properties and the potential correlations with the tooth function could be obtained. METHODS: We re-examined how mechanical properties such as elastic modulus and hardness transitioned from those of dentin to those of enamel using combined static and dynamic nanoindentation mapping techniques. A new mapping method and associated image processing procedures were developed to improve the measurement accuracy and resolution. RESULTS: A thin, sigmoidally-transitioned interphase layer of the DEJ was identified with an accurate functional width of 2-3µm. The DEJ width and gradient architecture were found intratooth location-dependent, with the DEJ at the occlusal sites being wider and transitioning smoother than that at the cervical sites. Such different widths and architectures of the interphase layer at sites subjected to different types and magnitudes of loadings during mastication could promote more efficient stress transferring between enamel and dentin without compromising the overall stiffness of the tooth. SIGNIFICANCE: The presented study not only adds our understanding in the local mechanical properties within tooth DEJ regions, it could also further advance the development of DEJ-mimetic, functional gradient interphase for strong and ultra-durable jointing between dissimilar materials.