Influence of Iron Substitution and Solution Composition on Brucite Carbonation.

Carbon neutral or negative mining can potentially be achieved by integrating carbon mineralization processes into the mine design, operations, and closure plans. Brucite [Mg(OH)2] is a highly reactive mineral present in some ultramafic mine tailings with the potential to be rapidly carbonated and can contain significant amounts of ferrous iron [Fe(II)] substituted for Mg; however, the influence of this substitution on carbon mineralization reaction products and efficiency has not been thoroughly constrained. To better assess the efficiency of carbon storage in brucite-bearing tailings, we performed carbonation experiments using synthetic Fe(II)-substituted brucite (0, 6, 23, and 44 mol % Fe) slurries in oxic and anoxic conditions with 10% CO2. Additionally, the carbonation process was evaluated using different background electrolytes (NaCl, Na2SO4, and Na4SiO4). Our results indicate that carbonation efficiency decreases with increasing Fe(II) substitution. In oxic conditions, precipitation of ferrihydrite [Fe10IIIO14(OH)2] and layered double hydroxides {e.g., pyroaurite [Mg6Fe2III(OH)16CO3·4H2O]} limited carbonation efficiency. Carbonation in anoxic environments led to the formation of Fe(II)-substituted nesquehonite (MgCO3·3H2O) and dypingite [Mg5(CO3)4(OH)2·âˆ¼5H2O], as well as chukanovite [Fe2IICO3(OH)2] in the case of 23 and 44 mol % Fe(II)-brucite carbonation. Carbonation efficiencies were consistent between chloride- and sulfate-rich solutions but declined in the presence of dissolved Si due to the formation of amorphous SiO2·nH2O and Fe-Mg silicates. Overall, our results indicate that carbonation efficiency and the long-term fate of stored CO2 may depend on the amount of substituted Fe(II) in both feedstock minerals and carbonate products.

Scaling-Free Cathodes: Enabling Electrochemical Extraction of High-Purity Nano-CaCO3 and -Mg(OH)2 in Seawater.

For electrochemical application in seawater or brine, continuous scaling on cathodes will form insulation layers, making it nearly impossible to run an electrochemical reaction continuously. Herein, we report our discovery that a cathode consisting of conical nanobundle arrays with hydrophobic surfaces exhibits a unique scaling-free function. The hydrophobic surfaces will be covered with microbubbles created by electrolytic water splitting, which limits scale crystals from standing only on nanotips of conical nanobundles, and the bursting of large bubbles formed by the accumulation of microbubbles will cause a violent disturbance, removing scale crystals automatically from nanotips. Benefiting from the scaling-free properties of the cathode, high-purity nano-CaCO3 (98.9%) and nano-Mg(OH)2 (99.5%) were extracted from seawater. This novel scaling-free cathode is expected to eliminate the inherent limitations of electrochemical technology and open up a new route to seawater mining.

Optimizing alkali-pretreatment dosage for waste-activated sludge disintegration and enhanced biogas production yield.

The rapid transition towards modernization and industrialization led to an increase in urban population, resulting in paramount challenge to municipal sewage sludge management. Anaerobic digestion (AD) serves as a promising venue for energy recovery from waste-activated sludge (WAS). Addressing the challenge of breaking down floc structures and microbial cells is crucial for releasing extracellular polymeric substances and cytoplasmic macromolecules to facilitate hydrolysis and fermentation process. The present study aims to introduce a combined process of alkaline/acid pre-treatments and AD to enhance sludge digestion and biogas production. The study investigates the influence of alkali pretreatment at ambient temperature using four alkali reagents (NaOH, Ca(OH)2, Mg(OH)2, and KOH). The primary goal is to provide insights into the intricate interplay of alkali dosages (0.04-0.12 g/gTS) on key physic-chemical parameters crucial for optimizing the pre-treatment dosage. Under the optimized alkaline/acid pre-treatment condition, the TSS reduction of 18%-30% was achieved. An increase in sCOD concentration (24%-50%) signifies the enhanced hydrolysis and solubilization rate of organic substrate in WAS. Finally, the biomethane potential test (BMPT) was performed for pre-treated WAS samples. The maximum methane (CH4) yield was observed in combination A1 (244 mL/g) and D1 (253 mL/g), demonstrating the pivotal role of alkali optimization in enhancing AD efficiency. This study serves as a valuable resource to policymakers, researchers, and technocrats in addressing challenges associated to sludge management.

In situ imaging of amorphous intermediates during brucite carbonation in supercritical CO2.

Progress in understanding crystallization pathways depends on the ability to unravel relationships between intermediates and final crystalline products at the nanoscale, which is a particular challenge at elevated pressure and temperature. Here we exploit a high-pressure atomic force microscope to directly visualize brucite carbonation in water-bearing supercritical carbon dioxide (scCO2) at 90 bar and 50 °C. On introduction of water-saturated scCO2, in situ visualization revealed initial dissolution followed by nanoparticle nucleation consistent with amorphous magnesium carbonate (AMC) on the surface. This is followed by growth of nesquehonite (MgCO3·3H2O) crystallites. In situ imaging provided direct evidence that the AMC intermediate acts as a seed for crystallization of nesquehonite. In situ infrared and thermogravimetric-mass spectrometry indicate that the stoichiometry of AMC is MgCO3·xH2O (x = 0.5-1.0), while its structure is indicated to be hydromagnesite-like according to density functional theory and X-ray pair distribution function analysis. Our findings thus provide insight for understanding the stability, lifetime and role of amorphous intermediates in natural and synthetic systems.

Cooperative Chemotaxis of Magnesium Microswimmers for Corrosion Spotting.

Numerous artificial micro- and nanomotors, as well as various swimmers have been inspired by living organisms that are able to move in a coordinated manner. Their cooperation has also gained a lot of attention because the resulting clusters are able to adapt to changes in their environment and to perform complex tasks. However, mimicking such a collective behavior remains a challenge. In the present work, magnesium microparticles are used as chemotactic swimmers with pronounced collective features, allowing the gradual formation of macroscopic agglomerates. The formed clusters act like a single swimmer able to follow pH gradients. This dynamic behavior can be used to spot localized corrosion events in a straightforward way. The autonomous docking of the swimmers to the corrosion site leads to the formation of a local protection layer, thus increasing corrosion resistance and triggering partial self-healing.

Zn Promoted Mg-Al Mixed Oxides-Supported Gold Nanoclusters for Direct Oxidative Esterification of Aldehyde to Ester.

The synthesis of ester compounds is one of the most important chemical processes. In this work, Zn-Mg-Al mixed oxides with different Zn2+/Mg2+ molar ratios were prepared via co-precipitation method and supported gold nanoclusters to study the direct oxidative esterification of aldehyde and alcohol in the presence of molecular oxygen. Various characterization techniques such as N2-physical adsorption, X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and CO2 temperature programmed desorption (TPD) were utilized to analyze the structural and electronic properties. Based on the results, the presence of small amounts of Zn2+ ions (~5 wt.%) provoked a remarkable modification of the binary Mg-Al system, which enhanced the interaction between gold with the support and reduced the particle size of gold. For oxidative esterification reaction, the Au25/Zn0.05MgAl-400 catalyst showed the best performance, with the highest turnover frequency (TOF) of 1933 h-1. The active center was believed to be located at the interface between metallic gold with the support, where basic sites contribute a lot to transformation of the substrate.

Evaluation of Optimized Procedures for High-Precision Lead Isotope Analyses of Seawater by Multiple Collector Inductively Coupled Plasma Mass Spectrometry.

The application of Pb isotopes to marine geochemistry is currently hindered by challenges associated with the analysis of Pb isotopes in seawater. The current study evaluates the performance of multiple collector inductively coupled plasma mass spectrometry (MC-ICP-MS) measurements of seawater Pb isotope compositions following Pb separation by either solid-phase extraction with Nobias Chelate PA-1 resin or coprecipitation with Mg(OH)2 and using either a Pb double spike or external normalization to Tl for mass bias correction. The four analytical combinations achieve results of similar quality when measuring 1-7 ng of seawater Pb, with reproducibilities (two standard deviations, 2SD) of 100-1200 ppm for 206Pb/207Pb and 208Pb/207Pb and 300-1700 ppm for ratios involving the minor 204Pb isotope. All four procedures enable significantly improved sample throughput compared to an established thermal ionization mass spectrometry (TIMS) double-spike method and produce unbiased seawater Pb isotope compositions with similar or improved precision. Nobias extraction is preferable to coprecipitation due to its greater analytical throughput and suitability for analyses of large seawater samples with high Si(OH)4 contents. The most accurate Pb isotope data are produced following Nobias extraction and double-spike correction as such analyses are least susceptible to matrix effects. However, Nobias extraction with Tl normalization constitutes an attractive alternative as, unlike the double-spike procedure, only a single mass spectrometric measurement is required, which improves analytical throughput and optimizes Pb consumption for analysis. Despite the advantages of solid-phase extraction, coprecipitation represents a useful Pb separation technique for samples with low to moderate Si contents as it is inexpensive, simple to implement, and the data are only marginally less accurate, especially when combined with a Pb double spike for mass bias correction.

Formation and loss of metastable brucite: does Fe(II)-bearing brucite support microbial activity in serpentinizing ecosystems?

Ultramafic rocks undergo successive stages of hydration and oxidation during water/rock interaction, giving rise to secondary minerals such as brucite, serpentine, magnetite and the production of H2(g). Ferroan brucite (MgxFe(1-x)2+(OH)2) often forms under low water/rock ratios early during the 'serpentinization' process. The formation of ferroan brucite sequesters Fe(II) and suppresses the production of H2, thereby limiting the flux of reductants suitable for sustaining microbial metabolism. Yet ferroan brucite is a relatively soluble mineral 'reservoir' for reactive Fe(II). Brucite is often metastable and can be lost at later stages of peridotite hydration when there is a significant increase in the water/rock ratio or the activity of SiO2 or CO2. The Fe(OH)2 component of brucite has the thermodynamic potential to reduce most aqueous oxidants. Therefore, ferroan brucite may reduce water and/or dissolved carbon, nitrogen and sulfur species, while the Fe(II) is converted into more stable secondary minerals such as Fe(II/III)-oxides and hydroxides (e.g. green-rust, magnetite, iowaite and pyroaurite) and ferric serpentine. The reactivity of ferroan brucite, and the associated rate of Fe solubilization and oxidation in subsurface fluids, could be a key regulator on the rate of electron transfer from serpentinites to the rock-hosted biosphere. Aqueous alteration of ferroan brucite may significantly modulate the H2 activity in fluids circulating within partially serpentinized rocks, and buffer H2 as it is lost by advection or in situ consumption by a hydrogenotrophic microbial community. Moreover, there may be microbial organisms that specifically colonize and use ferroan brucite as an electron donor for their metabolism. The energy fluxes sustained by localized brucite oxidation may often be sufficiently large to sustain abundant microbial communities; water/rock reaction zones where brucite is consumed could serve as environments to search for extant or fossil serpentinite-hosted life. This article is part of a discussion meeting issue 'Serpentinite in the Earth System'.

Differential Precipitation of Mg(OH)2 from CaSO4·2H2O Using Citrate as Inhibitor-A Promising Concept for Reagent Recovery from MgSO4 Waste Streams.

In hydrometallurgical processing and acidic wastewater treatment, one of the neutralizing agents employed is MgO or Mg(OH)2. At the end of this process, the resulting solution, which is rich in SO42- and Mg2+ is treated with lime to remove (or minimize the amount) of these ions via the precipitation of Mg(OH)2 and CaSO4·2H2O (gypsum). In our work, an attempt was made to separate the two solids by increasing the induction time of the gypsum precipitation, thus regenerating relatively pure Mg(OH)2 which could be reused in wastewater treatments or hydrometallurgical processing circuits, and in this way, significantly enhancing the economic viability of the process. During our experiments, the reaction of an MgSO4 solution with milk of lime prepared from quicklime was studied. The effects of a range of organic additives, which can slow down the precipitation of gypsum have been assessed. The process was optimized for the most promising inhibiting agent-that is, the citrate ion. The reactions were continuously monitored in situ by conductometric measurements with parallel monitoring of solution pH and temperature. ICP-OES measurements were also carried out on samples taken from the reaction slurry. The composition of the precipitating solids at different reaction times was established by powder XRD and their morphology by SEM. Finally, experiments were carried out to locate the additive after the completion of the precipitation reaction to get information about its potential reuse.

Synthesis of Hydrotalcites from Waste Steel Slag with [Bmim]OH Intercalated for the Transesterification of Glycerol Carbonate.

Ca-Mg-Al hydrotalcites were prepared by coprecipitation from Type S95 steel slag of Shanghai Baosteel Group as supports of ionic liquid in this paper. Five basic ionic liquids [Bmim][CH3COO], [Bmim][HCOO], [Bmim]OH, [Bmim]Br and ChOH were prepared and their catalytic performance on the synthesis of glycerol carbonate by transesterification between dimethyl carbonate and glycerol was investigated. The characterization results indicated that [Bmim]OH is the best ionic liquid (IL) for the transesterification reaction of glycerol carbonate. The hydrotalcites before and after intercalation by ionic liquid were characterized by XRD, FTIR, SEM, EDS and the IL were characterized by FT-IR, 13C-NMR and basicity determination via the Hammett method. The analysis results implied that the dispersion of [Bmim]OH in hydrotalcites reduced the alkali density appropriately and facilitated the generation of glycerol carbonate. The yield of glycerol carbonate and the conversion rate of glycerol reached 95.0% and 96.1%, respectively, when the molar ratio of dimethyl carbonate and glycerol was 3:1, the catalyst dosage was 3 wt%, the reaction temperature was 75 °C and the reaction time was 120 min. The layered structure of hydrotalcites increased the stability of ionic liquid intercalated in carriers, thus the glycerol conversion and the GC yield still remained 91.9% and 90.5% in the fifth reaction cycle.

Arsenic removal from groundwater in Kütahya, Turkey, by novel calcined modified hydrotalcite.

Since arsenic is highly toxic and carcinogenic, it now causes serious health problems all over the world. Therefore, there is an urgent need to develop new techniques that are cost-effective and easily applicable to remove arsenic from contaminated waters. Layer double hydroxides have the potential to be a good adsorbent to remove arsenic from contaminated waters due to high surface area and high anion exchange capacity. In this paper, arsenic removal from water by calcined Fe-hydrotalcite (CFeHT) known as layered double hydroxide and prepared synthetically with coprecipitation method was researched. The study brings out that the effect of initial solution pH values was limited for the adsorption. The experimental study indicates that the adsorption of arsenic rapidly occured in comparison with other studies. It was determined that the pseudo-second-order kinetic model was more suitable than the first order. In isotherm studies, it was seen that the experimental data were compatible with Langmuir model. In this study was determined that CFeHT has a high arsenic removal potential. And also the concentration of the arsenic solution (600 µg/L) has been reduced below the allowable value by the World Health Organization (< 10 µg/L). The desorption test indicates that the desorption ratio of As(V) was obtained as 72.7.

Detoxification of sugarcane bagasse hydrolysate with different adsorbents to improve the fermentative process.

Second generation ethanol has the prospect of becoming an important bioenergy alternative. The development of this technology is associated with the lignocellulosic materials' use, with emphasis on agricultural and agroindustrial by-products from which fermentable sugar can be produced. The acid hydrolysis depolymerizes the hemicellulose releasing mainly xylose. Subsequently, the cellulose can be converted into glucose by enzymatic hydrolysis. However, the acid hydrolysis produces toxic compounds, such as furan derivatives, phenolics, and organic acids, which are harmful to fermentative microorganisms. This study investigated different acid concentrations in the sulfuric acid hydrolysis of sugarcane bagasse (1- 5% m/v) and the use of adsorbents with the prerogative to improve the acid hydrolysate (AH) quality for microbial ethanolic fermentation. Cell growth and fermentative yield of Saccharomyces cerevisiae (PE-2) and Scheffersomyces stipitis (NRRL Y-7124) were evaluated. AH was used as a source of pentoses (17.7 g L-1) and molasses (ME) sugarcane as source of hexoses (47 g L-1). The following adsorbents were used: activated charcoal, clay, hydrotalcite and active and inactive cells of PE-2 and NRRL Y-7124, at concentrations ranging (1 - 8% m/v). Results of cell growth and chemical characterization allowed to select the most effective adsorbents with emphasis for active cells that removed 66% furfural and 51% 5-(hydroxymethyl) furfural) (5-HMF) and alcoholic productivity of 23.5 g L-1 in AH and ME substrates, in the presence of mixed culture. These results indicate the application of active yeast cells in the detoxification of acid hydrolysates of the sugarcane bagasse previously to the fermentation.

Dynamics of Clay-Intercalated Ibuprofen Studied by Solid State Nuclear Magnetic Resonance.

In designing drug delivery systems with improved release properties and bioavailability, the dynamic features of the active pharmaceutical ingredient can be crucial for the final product properties. In this work, we aimed at obtaining the first characterization of the molecular dynamic properties of one of the most common nonsteroidal anti-inflammatory drug, ibuprofen, intercalated in hydrotalcite, an interesting inorganic carrier. By exploiting a variety of solid state NMR techniques, including 1H and 13C MAS spectra and T1 relaxation measurements, performed at variable temperature and carrying out a synergic analysis of all results, it has been possible to ascertain that the mobility of ibuprofen within the carrier is remarkably increased. In particular, strong indications have been obtained that ibuprofen molecules, in addition to internal interconformational dynamics, experience an overall molecular motion. Also considering that ibuprofen is "anchored" to the charged surface of the hydrotalcite layers through its carboxylate moiety, such motion could be a wobbling-in-a-cone. Activation energies and correlation times of all the motions of intercalated ibuprofen have been determined.

Adsorption Capability of Fe-HT3.0 for Nitrite and Nitrate Ions in a Binary Solution System.

In this study, the adsorption capability of Fe-HT3.0 for nitrite and nitrate ions in a binary solution system was evaluated. It was found that the amount of nitrite and nitrate ions adsorbed in a single solution (1.19 and 1.27 mmol/g, respectively) was higher than that in a binary solution (0.36 and 0.90 mmol/g, respectively). Equilibrium adsorption was attained within 6-24 h. The adsorption data were fitted to a pseudo-second-order model (correlation coefficient: 0.999), and indicated that the adsorption of both nitrite and nitrate ions is controlled by chemical sorption. Additionally, the binding energies before and after the adsorption of nitrite and nitrate ions in the binary solution system were measured. After adsorption, new nitrogen peaks (approx. 399 and 403 eV) were detected. The results of this study show the potential of Fe-HT3.0 for the removal of nitrite and nitrate ions from aqueous solution systems.

The Impact of Magnesium-Aluminum-Layered Double Hydroxide-Based Polyvinyl Alcohol Coated on Magnetite on the Preparation of Core-Shell Nanoparticles as a Drug Delivery Agent.

One of the current developments in drug research is the controlled release formulation of drugs, which can be released in a controlled manner at a specific target in the body. Due to the diverse physical and chemical properties of various drugs, a smart drug delivery system is highly sought after. The present study aimed to develop a novel drug delivery system using magnetite nanoparticles as the core and coated with polyvinyl alcohol (PVA), a drug 5-fluorouracil (5FU) and Mg-Al-layered double hydroxide (MLDH) for the formation of FPVA-FU-MLDH nanoparticles. The existence of the coated nanoparticles was supported by various physico-chemical analyses. In addition, the drug content, kinetics, and mechanism of drug release also were studied. 5-fluorouracil (5FU) was found to be released in a controlled manner from the nanoparticles at pH = 4.8 (representing the cancerous cellular environment) and pH = 7.4 (representing the blood environment), governed by pseudo-second-order kinetics. The cytotoxicity study revealed that the anticancer delivery system of FPVA-FU-MLDH nanoparticles showed much better anticancer activity than the free drug, 5FU, against liver cancer and HepG2 cells, and at the same time, it was found to be less toxic to the normal fibroblast 3T3 cells.

Carminic Acid Stabilized with Aluminum-Magnesium Hydroxycarbonate as New Colorant Reducing Flammability of Polymer Composites.

In this study, hybrid pigments based on carminic acid (CA) were synthesized and applied in polymer materials. Modification of aluminum-magnesium hydroxycarbonate (LH) with CA transformed the soluble chromophore into an organic-inorganic hybrid colorant. Secondary ion mass spectroscopy (TOF-SIMS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and UV-Vis spectroscopy were used to study the structure, composition, and morphology of the insoluble LH/CA colorant. Successful modification of the LH was confirmed by the presence of interactions between the LH matrix and molecules of CA. XPS analysis corroborated the presence of CA complexes with Mg2+ ions in the LH host. The batochromic shift in UV-Vis spectra of the organic-inorganic hybrid colorant was attributed to metal-dye interactions in the organic-inorganic hybrid colorants. Strong metal-dye interactions may also be responsible for the improved solvent resistance and chromostability of the modified LH. In comparison to uncolored ethylene-norbornene copolymer (EN), a modified EN sample containing LH/CA pigment showed lower heat release rate (HRR) and reduced total heat release (THR), providing the material with enhanced flame retardancy.

Characterization and Structure⁻Property Relationships of Organic⁻Inorganic Hybrid Composites Based on Aluminum⁻Magnesium Hydroxycarbonate and Azo Chromophore.

In this study, novel organic⁻inorganic composites were prepared by the complexation of dicarboxylic azo dye (AD) with aluminum⁻magnesium hydroxycarbonate (AlMg⁻LH). This procedure provides an effective method for the stabilization of dicarboxylic organic chromophores on an AlMg-LH host. The structures of the hybrid composites were examined by X-ray diffraction (XRD), secondary ion mass spectrometry (TOF-SIMS), 27-Al solid-state nuclear magnetic resonance (NMR) spectroscopy, thermogravimetric analysis (TGA) and scanning transmission electron microscopy (STEM). The TOF-SIMS method was applied to investigate the metal⁻dye interactions and to monitor the thermal stability of the organic⁻inorganic complexes. Secondary ion mass spectrometry confirmed the presence of a characteristic peak for C18H10O5N2Mg22+, indicating that both carboxylic groups interacted with AlMg-LH by forming complexes with two Mg2+ ions. Modification with hybrid pigments affected the crystal structure of the AlMg-LH mineral, as shown by the appearance of new peaks on the X-ray diffraction patterns. Adsorption of the dicarboxylic chromophore not only led to significantly enhanced solvent resistance but also improved the thermal and photostability of the hybrid pigments. We propose a possible arrangement of the azo dye in the inorganic matrix, as well as the presumed mechanism of stabilization.

Dentifrice Based on Fluoride-Hydrotalcite Compounds: Characterization and Release Capacity Evaluation by Novel In Vitro Methods.

Anti-caries activity of fluoride ions is due to the protection against demineralization and the enhancement of remineralization of tooth enamel. Dentifrices available on the market contain sodium fluoride, sodium monofluorophosphate, stannous fluoride, and amine fluoride as source of these ions. A new compound working both as fluoride ion source and as abrasive was projected. Hybrids based on F- ions intercalated between the lamellae of hydrotalcite-like compounds (HTlc-F), namely MgAl-HTlc-F and ZnAl-HTlc-F, were prepared and characterized. Then, three different percentages (2, 3, and 4%) of both HTlc-F compounds were assayed. After the rheological characterization, the dentifrices containing 3 and 4% of MgAl-HTlc-F and ZnAl-HTlc-F, respectively, resulted to be the most suitable ones. Two novel in vitro methods, "rotary toothbrush method" and "manual brushing method," were developed and used in order to study the F- ions release from the prepared dentifrices. The obtained results showed that the dentifrice containing ZnAl-HTlc-F (4%) was the most effective in releasing fluoride ions. The "rotary toothbrush method" resulted to be the most suitable as the simulation of the brushing movements is standardizable and reproducible.

Fluid mixing and the deep biosphere of a fossil Lost City-type hydrothermal system at the Iberia Margin.

Subseafloor mixing of reduced hydrothermal fluids with seawater is believed to provide the energy and substrates needed to support deep chemolithoautotrophic life in the hydrated oceanic mantle (i.e., serpentinite). However, geosphere-biosphere interactions in serpentinite-hosted subseafloor mixing zones remain poorly constrained. Here we examine fossil microbial communities and fluid mixing processes in the subseafloor of a Cretaceous Lost City-type hydrothermal system at the magma-poor passive Iberia Margin (Ocean Drilling Program Leg 149, Hole 897D). Brucite-calcite mineral assemblages precipitated from mixed fluids ca. 65 m below the Cretaceous paleo-seafloor at temperatures of 31.7 ± 4.3 °C within steep chemical gradients between weathered, carbonate-rich serpentinite breccia and serpentinite. Mixing of oxidized seawater and strongly reducing hydrothermal fluid at moderate temperatures created conditions capable of supporting microbial activity. Dense microbial colonies are fossilized in brucite-calcite veins that are strongly enriched in organic carbon (up to 0.5 wt.% of the total carbon) but depleted in (13)C (δ(13)C(TOC) = -19.4‰). We detected a combination of bacterial diether lipid biomarkers, archaeol, and archaeal tetraethers analogous to those found in carbonate chimneys at the active Lost City hydrothermal field. The exposure of mantle rocks to seawater during the breakup of Pangaea fueled chemolithoautotrophic microbial communities at the Iberia Margin, possibly before the onset of seafloor spreading. Lost City-type serpentinization systems have been discovered at midocean ridges, in forearc settings of subduction zones, and at continental margins. It appears that, wherever they occur, they can support microbial life, even in deep subseafloor environments.

Adsorption of Nitrite and Nitrate Ions from an Aqueous Solution by Fe-Mg-Type Hydrotalcites at Different Molar Ratios.

In this study, we prepared Fe-Mg-type hydrotalcites (Fe-HT3.0 and Fe-HT5.0) with different molar ratios and evaluated their adsorption capability for nitrite and nitrate ions from aqueous solution. Fe-HT is a typical hydrotalcite-like layered double hydroxide. Adsorption isotherms, as well as the effects of contact time and pH were investigated, and it was found that Fe-HT can adsorb larger amounts of nitrite and nitrate ions than Al-HT (normal-type hydrotalcite). Adsorption isotherm data were fitted to both Freundlich (correlation coefficient: 0.970-1.000) and Langmuir (correlation coefficient: 0.974-0.999) equations. Elemental analysis and binding energy of Fe-HT surface before and after adsorption indicated that the adsorption mechanism was related to the interaction between the adsorbent surface and anions. In addition, the ion exchange process is related to the adsorption mechanism. The adsorption amount increased with increasing temperature (7-25°C). The experimental data fit the pseudo-second-order model better than the pseudo-first-order model. The effect of pH on adsorption was not significant, which suggested that Fe-HT could be used over a wide pH range (4-12). These results indicate that Fe-HT is a good adsorbent for the removal of nitrite and nitrate ions from aqueous solution.