A kit to prepare (111)In-DTPA-trastuzumab (Herceptin) Fab fragments injection under GMP conditions for imaging or radioimmunoguided surgery of HER2-positive breast cancer.
Nucl Med Biol
; 38(1): 129-36, 2011 Jan.
Article
em En
| MEDLINE
| ID: mdl-21220136
ABSTRACT
INTRODUCTION:
The human epidermal growth factor receptor-2 (HER2) gene is amplified in 25% of invasive breast cancers, and receptor overexpression has been noted in up to 60% of early stages of the disease [ductal carcinoma in situ (DCIS)]. Preclinical studies have revealed high tumor/blood ratios (>271) for (111)In-labeled Fab fragments of the HER2 monoclonal antibody, trastuzumab (Herceptin) ((111)In-DTPA-trastuzumab Fab) at 72 h pi in athymic mice bearing subcutaneous human breast cancer xenografts. Our aim in this study was to formulate a kit for preparation of (111)In-DTPA-trastuzumab Fab injection under good manufacturing practice (GMP) conditions suitable for human administration in a Phase I clinical trial of imaging and radioimmunoguided surgery (RIGS) of HER2-positive breast cancer.METHODS:
Fab fragments were produced by digestion of trastuzumab IgG (Herceptin) with immobilized papain for 20 h at 37°C. Fab fragments were purified by ultrafiltration, then reacted with a 10-fold molar excess of diethylenetriaminepentaacetic acid (DTPA) dianhydride. DTPA-Fab fragments were purified, then sterilized by filtration into unit dose glass vials (kits). Kits were tested against specifications for volume (0.9-1.1 ml), protein concentration (0.45-0.55 mg/ml), pH (5.5-6.5), DTPA substitution (0.5-4.0 mol DTPA/mol Fab), appearance (clear, colorless and particle free), labeling efficiency (≥ 85%), and sterility and apyrogenicity (USP XXXII). Immunoreactivity of (111)In-DTPA-trastuzumab Fab towards HER2 was measured by saturation radioligand binding assays using SKBR-3 human breast cancer cells (specifications K(a) = 0.6-9.6 × 10(7) L/mol; B(max) = 0.6-10.4 × 10(6) sites/cell). (111)In-DTPA-trastuzumab Fab injection was prepared by adding 80-100 MBq of (111)InCl(3) to a single kit vial and incubating for 30 min at room temperature. (111)In-DTPA-trastuzumab Fab was assayed for the amount of radioactivity and tested for pH, radiochemical purity (RCP), appearance and sterility.RESULTS:
Pure and homogeneous Fab fragments were produced. Eleven lots of kits met established quality specifications. The labeling efficiency with (111)In was 90.6 ± 2.2%. (111)In-DTPA-trastuzumab Fab bound specifically to HER2 on SKBR-3 cells (K(a) = 4.8 ± 2.5 × 10(7) L/mol and B(max) = 1.6 ± 0.8 × 10(6) sites/cell). Thirteen lots of (111)In-DTPA-trastuzumab injection met all established specifications. Kits were stable for 90 days and (111)In-DTPA-trastuzumab Fab injection was stable for 24 h stored at 4 °C.CONCLUSIONS:
A kit was formulated under GMP conditions for the preparation of (111)In-DTPA-trastuzumab Fab injection suitable for human administration. The kits were approved by Health Canada.
Texto completo:
1
Base de dados:
MEDLINE
Assunto principal:
Neoplasias da Mama
/
Fragmentos Fab das Imunoglobulinas
/
Receptor ErbB-2
/
Cirurgia Assistida por Computador
/
Ácido Pentético
/
Imagem Molecular
/
Anticorpos Monoclonais
Tipo de estudo:
Clinical_trials
/
Diagnostic_studies
Limite:
Humans
Idioma:
En
Ano de publicação:
2011
Tipo de documento:
Article