Patient Satisfaction and Accuracy of Partial Denture Frameworks Fabricated using Conventional and Digital Techniques.

This case report compares a conventional and a digital workflow for manufacturing metal frameworks for maxillary and mandibular removable partial dentures (RPDs). Two sets of maxillary and mandible RPDs were produced. The metal framework of one set of RPDs was produced conventionally using the lost wax casting technique. Intraoralscanning and computer-aided designing (CAD) were used to fabricate the metal frameworks of the other set of RPDs using direct metal laser sintering (DMLS) technology. The accuracy of fit of the two sets of RPDs was evaluated after 3 months using replica models. Patient satisfaction was assessed. Two years later, the fit accuracy of the DMLS prosthesis and patient satisfaction were re-evaluated. The accuracy of fit in the maxillary RPD with the DLMS manufactured metal framework showed better results in all areas except areas of rests (457 vs. 421 µm) and the major connector (850 vs. 512 µm). The mandibular RPD with DLMS manufactured metal framework showed only in the areas of the reciprocal arm and major connector better fit accuracy compared to the conventional RPD. The patient satisfaction with the DLMS manufactured RPDs was rated equally to the conventional one. The use of digital technologies in manufacturing RPDs seems promising regarding accuracy and patient satisfaction.

Evaluation of oxidative stress cycle in healthy and inflamed dental pulp tissue: a laboratory investigation.

OBJECTIVES: The purpose of this study was to investigate the oxidative stress cycle consisting of reactive oxygen molecules (ROS), glutathione (GSH) and glutathione S-transferase (GST) in caries-related pulp inflammation. METHODOLOGY: Fifty-four pulp tissue samples were collected from healthy donors with the diagnosis of reversible pulpitis, symptomatic irreversible pulpitis, and healthy pulp. Twelve pulp samples from each group were homogenized and total protein, ROS, GSH, and GST were measured by spectrophotometer. The remaining 6 samples from each group were prepared for paraffin block and used for the histopathologic and immunohistochemical evaluation of oxidative stress parameters and TUNEL labeling. Data were analyzed statistically. RESULTS: The results revealed that total protein levels significantly decreased; however, ROS levels increased in both reversible and irreversible pulpitis compared to the healthy pulp (p < 0.01). Also, as inflammation increases, GST enzyme levels decrease while GSH levels increase significantly (p < 0.05). It was found that the number of TUNEL (+) cells was increased in irreversible pulpitis samples compared to healthy and reversible pulpitis groups (p < 0.05). GSTP1 and GSH immunoreactivity were also observed in irreversible pulpitis samples. CONCLUSIONS: It has been revealed that caries-related inflammation alters the oxidative stress cycle in dental pulp tissue. The increase in GSH levels in the inflamed dental pulp due to the increase in ROS levels may improve the defensive ability of the dental pulp. CLINICAL RELEVANCE: There is a relationship between oxidative stress and inflammation. Control of excessive oxidative stress in pulpitis can stimulate reparative and regenerative processes. The present findings may provide an overview of the management of oxidative stress in cases with pulpitis during regenerative treatments.

Clinical longevity of intracoronal restorations made of gold, lithium disilicate, leucite, and indirect resin composite: a systematic review and meta-analysis.

OBJECTIVES: The aim of this systematic review and meta-analysis is to assess the comparative clinical success and survival of intracoronal indirect restorations using gold, lithium disilicate, leucite, and indirect composite materials. MATERIAL AND METHODS: This systematic review and meta-analysis were conducted following the Cochrane Handbook for Systematic Reviews of Interventions and PRISMA guidelines. The protocol for this study was registered in PROSPERO (registration number: CRD42021233185). A comprehensive literature search was conducted across various databases and sources, including PubMed/Medline, Embase, Cochrane Library, Web of Science, ClinicalTrials.gov, and gray literature. A total of 7826 articles were screened on title and abstract. Articles were not excluded based on the vitality of teeth, the language of the study, or the observation period. The risk difference was utilized for the analyses, and a random-effects model was applied. All analyses were conducted with a 95% confidence interval (95% CI). The calculated risk differences were derived from the combined data on restoration survival and failures obtained from each individual article. The presence of heterogeneity was assessed using the I2 statistic, and if present, the heterogeneity of the data in the articles was evaluated using the non-parametric chi-squared statistic (p < 0.05). RESULTS: A total of 12 eligible studies were selected, which included 946 restorations evaluated over a minimum observation period of 1 year and a maximum observation period of 7 years. Results of the meta-analysis indicated that intracoronal indirect resin composite restorations have an 18% higher rate of failure when compared to intracoronal gold restorations over 5-7 years of clinical service (risk difference = - 0.18 [95% CI: - 0.27, - 0.09]; p = .0002; I2 = 0%). The meta-analysis examining the disparity in survival rates between intracoronal gold and leucite restorations could not be carried out due to methodological differences in the studies. CONCLUSIONS: According to the currently available evidence, medium-quality data indicates that lithium disilicate and indirect composite materials demonstrate comparable survival rates in short-term follow-up. Furthermore, intracoronal gold restorations showed significantly higher survival rates, making them a preferred option over intracoronal indirect resin-composite restorations. Besides that, the analysis revealed no statistically significant difference in survival rates between leucite and indirect composite restorations. The short observation period, limited number of eligible articles, and low sample size of the included studies were significant limitations. CLINICAL SIGNIFICANCE: Bearing in mind the limitations of the reviewed literature, this systematic review and meta-analysis help clinicians make evidence-based decisions on how to restore biomechanically compromised posterior teeth.

Immediate and Late Repair of Microhybrid Resin Composites: Effect of Silane Coupling Agent, Universal Adhesives and Photo Polymerization.

This study investigated the effect of silane coupling agent and universal adhesive application on repair bond strength of resin-based composite after bur grinding. Microhybrid resin composite (Charisma Smart) blocks (N=80; 8x8x4 mm3) were prepared, aged (37°C; 1 month), roughened, etched and randomly divided into two groups. Silane was applied to half of the groups (Porcelain Primer, Bisco), before one of the following universal primers/adhesives was applied: a) Scotchbond Universal (3M), b) All-Bond Universal (Bisco), c) G-Premio Bond (GC), and d) Clearfil SE Bond (Kuraray). In each adhesive group half of the group was photo-polymerized. The blocks were repaired with the same size resin composite and segmented into beams. Half of the beams were subjected to micro-tensile bond test (1 mm/min), while the other half was aged (37°C; 6 months) prior to testing. Failure modes were analyzed using Scanning Electron Microscopy (SEM). Data were analyzed using repeated measures of ANOVA, Tukey's post-hoc, and paired t-tests (alpha=0.05). The silane application did not affect the repair bond strength regardless of photo-polymerization of the adhesive resin. The repair bond strength decreased significantly after 6 months when adhesive resin was not photopolymerized (p⟨0.05). Photo-polymerizing universal adhesives might ensure higher repair bond strength and its maintenance after aging.

Effect of Thickness and Translucency on Color Change and Masking Ability of Ceramic Materials used for Laminate Veneers.

This study evaluated the effect of the thickness and translucency of lithium disilicatebased glass ceramics on resin composite substrates on color change and masking effect. Laminate veneers were fabricated using IPS e.max CAD (A1) blocks with two different light transmittance values (High translucent [HT], Low translucent [LT]). Slices of two different thicknesses (0.3 mm, 0.5 mm) were obtained (n=10) and laminate veneers were cemented on the resin composite substrates of two different shades (A2, A3.5). The color change (ΔE values) was evaluated with the CIELab color system using a spectrophotometer, while the masking effect was calculated. The data were analyzed using independent-samples t-test and two-way analysis of variance. The ceramic thickness and translucency had a significant effect on final color and masking. When HT was used, and the laminate veneer thickness decreased (0.3 mm), the masking effect in ΔE values were lower (p⟨0.05). The ΔE values (⟩3.7) were clinically unacceptable. With the increase in thickness, translucency of porcelain laminate veneers decreases showing better color masking ability. Veneer thickness seems to be more effective on the restoration's masking ability than the shade of the substrate and translucency. Cinically, in case a 0.5-mm or thinner laminate veneer is planned, tooth color, resin cement and ceramic type should be considered.

Evaluation of New Alkasite Based Restorative Material for Restoring Non- Carious Cervical Lesions- Randomized Controlled Clinical Trial.

Two different restoration materials, an alkasite-based resin composite and a resinmodified glass ionomer cement were used to assess restoration of non-carious cervical dental lesions. This split mouth randomized controlled trial included 40 patients. After randomization both sides of the dental arch were restored with either an alkasite-based (Cention N, Ivoclar Vivadent) or a resin-modified glass ionomer cement (Voco GmbH) restoration. The placed fillings were evaluated by blinded additional operators 1, 6 months and 1 year after to the USPHS criteria (retention, marginal integrity and discoloration, anatomical form and secondary caries). Data were analyzed using Kendall's Coefficient of Concordance test and Chi-square tests using SPSS software (SPSS Inc., Version 20) (P=0.05). As for retention and anatomic form both materials performed similar after one month. However, the retention and anatomic form for alkasite based restorative Cention showed significantly better results after 6 months (p=0.013/p=0.003) and one year (p=0.026/p=0.008). The resin modified glass ionomer restoration showed higher discoloration after 6 months (p=0.025) and one year (p=0.018), while Cention performed better regarding marginal integrity at all time intervals. No secondary caries occurred. Alkasite based restorative materials displayed superior technical, mechanical and aesthetical performance in a follow-up period of one year and can therefore be recommended as an alternative to resin-modified glass ionomer cements.

EPA Consensus Project Paper: Anterior Full or Partial Coverage Single Tooth Restorations - A Systematic Review of Survival and Complication Rates.

INTRODUCTION: The aim of this systematic review was to assess the literature reporting on the failure rates, survival rates and complication rates and patient reported outcome measures (PROMs) of anterior full (FC) or partial (PC) coverage single tooth restorations after a mean observation period of at least 3 years. METHODS: Systematic search was conducted using the electronic databases: MEDLINE, EMBASE and Cochrane library. Data regarding survival (restoration failure) and complication rates and PROMs were extracted and presented descriptively. RESULTS: Altogether 42 studies were included in the analysis (28 with FC, 12 with PC and 2 with both types of restorations). For FC restorations the estimated annual failure rate was 0.72 (95%CI: 0.33-1.57), resulting in a 5-year survival rate of 96.4% (95%CI: 92.4-98.3). For PC restorations, the estimated annual failure rate was 0.62 (95%CI: 0.27-1.46), resulting in a 5-year survival rate of 96.9% (95%CI: 93.0-98.7). There was no significant difference between the groups regarding survival or technical complications, while significantly fewer biological complications were observed with PC compared to FC restorations (test for subgroup differences, p=0.01). CONCLUSIONS: FC and PC restorations showed high 5-year survival rates but the teeth restored with FC restorations may be more prone to biological complications.

Evaluation of Clinical Periodontal Parameters of Abutment Teeth Supporting Distal-Extension Base Removable Partial Dentures: A Cross-sectional Study.

To assess the clinical periodontal status of abutment teeth in regards of different design components of distal-extension removable partial dentures. Subjects (N=100) with acrylic or cobalt-chromium distal-extension removable partial dentures were enrolled and their periodontal parameters plaque and gingival indices [PI, GI], probing depths [PD], clinical attachment loss [CAL] and a mobility index [MI] evaluated. Denture base type, major connector, occlusal rests position, design of direct retainers, retention, stability and denture wearing habits were further evaluated. Acrylic RPDs were associated with higher mean±SE PI [1.70±0.74], GI [1.76±0.55], PD scores [2.47±1.02 mm] and CAL values [4.46±2.11 mm] compared to CO-CR RPDs [p⟨0.05]. For abutments, the PI [1.6±0.83], GI [1.72±0.57], PD [2.32±1.03] and CAL [4.26±2.08] were higher than their non-abutments counterparts [p⟨0.05]. CAL scores were found to be significantly higher for mandibular abutments compared to maxillary ones [P=0.002]. The highest PI [1.83±1.10] and GI [2.00±0.00] scores were associated with lingual bars and horse-shoe connectors, respectively. Full palatal coverage and lingual plates were associated with the highest PD [2.80±0.48] and CAL [4.70±0.37] scores. Acrylic RPDs, type of major connector, wrought wire clasps and distal occlusal rests may be considered as risk factors for periodontal disease progression in distal-extension removable partial denture wearers.

Comparative Evaluation of Apically Extruded Debris During Root Canal Preparation Using Three Different File Systems Applied Under 2.5% Sodium Hypochlorite or 2% CHX Irrigation.

The chemomechanical cleaning of the root canal system is performed using manual and rotary files. This study aimed to compare the effect of ProTaper, Reciproc and HyFlex rotary files considering 2.5% sodium hypochlorite and 2% chlorhexidine (CHX) as irrigating solutions on apical extrusion of intracanal debris. Single-canal mandibular premolars (N=165) were evaluated. The teeth were divided into 6 experimental groups (N=25) for root canal instrumentation using 3 file systems, (Reciproc, HyFlex and ProTaper) and two irrigation solutions, namely 2.5% sodium hypochlorite or 2% CHX. Fifteen teeth were also assigned into three control groups (n=5) with saline as irrigation solution. Eppendorf tubes were weighed and the teeth were placed inside. The canals were instrumented and the tubes weighed to determine the dry weight of extruded debris. Data were analyzed using one-way ANOVA and Bonferroni test (α=0.05). The mean amount of extruded debris using the sodium hypochlorite solution was significantly higher than other irrigating solutions (p⟨0.001). The mean amount of extruded debris using the Reciproc file system was significantly higher compared to ProTaper and HyFlex (p⟨0.001). The use of the sodium hypochlorite solution, single-file systems and reciprocal movement are associated with higher debris extrusion and might be associated with higher risk of postoperative pain.

THE PREVALENCE OF POLYNEUROPATHY IN THE PRE-DIABETES PERIOD.

Objective: This study aims to determine the prevalence of neuropathy in the prediabetic period. Design Subjects and Method: Informed consent was attained from the patients who volunteered to participate in the study after ethics committee approval was obtained. Patients under the age of 18, having vitamin B12 or folic acid deficiency, history of collagen tissue-rheumatological disease, chronic kidney failure, cirrhosis, ethylism, thyroid disease, autoimmune disease, malignancy, tuberculosis, type 1 or 2 diabetes mellitus and pregnant women were excluded from the study. Patients diagnosed with prediabetes were evaluated by the DN4 neuropathy complaint questionnaire. Neuropathy was diagnosed in patients having a score of four or more. For the statistical analyses Student t-test, Pearson chi-square test, and Fisher's exact test were performed using the NCSS program. Results: A total of 224 volunteers, 167 women and 57 men, were included in the study. The mean age of the participants was 51 and the mean level of hemoglobin A1C was 5.9. Neuropathy was detected in 45% of the cases. Especially in women, there was a significant increase in the frequency of neuropathy compared to men. The most common complaints found in our study were burning sensation and numbness in the extremities. Conclusions: Similar to diabetic patients, prediabetic patients also have a high rate of neuropathy. For the early diagnosis of neuropathy and to be treated promptly, screening tests such as DN4 should be performed for all prediabetic patients. According to the test results, advanced examinations such as EMG or biopsy should be performed earlier.

Implant-Supported Extra-Orally Cemented Monolithic Zirconia Crowns: A Prospective Controlled Clinical Study up to 18 Months in Function.

This study evaluated the clinical performance of implant supported, extra-orally cemented, monolithic zirconia crowns after a follow-up to 18 months. Thirty-one patients with 50 posterior dental implants were consecutively selected for this study. A total of 50 crowns were cemented onto titanium abutments extra-orally and then screwed to the implants with the required torque intra-orally. The patients were followed at 12 months and 18 months after placement of restorations. During the follow-up period, all restorations were evaluated according to following technical parameters: implant failure, crown fracture, screw loosening, loss of retention due to decementation, fracture of antagonist tooth or restoration. Data were analyzed using Kaplan Meier method. One implant and its corresponding crown was lost during the follow-up period, yielding a 18 months survival rate of 98%. During the study, 2 complication events were observed, including one screw loosening and one veneering porcelain chipping in an antagonist bilayered zirconia restoration. The overall success rate of the observed prosthesis was 96%. According to the results of this study, the extra-orally cemented, monolithic zirconia crowns resulted in a favorable short-term outcome for posterior implant supported restorations within this short observation time.

Accuracy of Removable Partial Denture Frameworks Fabricated Using Conventional and Digital Technologies.

This study analyzed the fit accuracy of the removable partial denture (RPD) metal frameworks produced using digital and conventional manufacturing technologies. Mandibular RPD metal frameworks (N=15, n=3 per group) were fabricated on a representative clinical case. RPDs were fabricated using one of the following manufacturing procedures: a) conventional lost-wax casting technique (C-LW), b) conventional casting of milled sacrificial patterns (C-M), c) conventional casting of printed sacrificial patterns (C-P), d) selective laser melting (SLM), e) direct metal laser sintering (DMLS) technologies. The fit accuracy of RPD frameworks was analyzed by fabricating replicas with silicone registration material and measuring with a digital microscope. A total of 11 sites and 29 areas in the RPD metal frameworks were considered for the accuracy measurements (µm). Data were statistically analyzed using Wilcoxon signed rank and Friedman test (α=0.05). Before finishing and polishing, C-M method presented overall significantly better (P⟨.001) fit accuracy (118 µm) than those of other methods (195-265 µm). After finishing and polishing, C-M method showed overall significantly better (P⟨.033) fit accuracy (205.7 µm) than C-LW and SLM methods (285.7 µm; 249 µm) and comparable fit accuracy to that of C-P and DMLS methods. Accuracy at the minor and major connector areas of RPDs were affected from the manufacturing technologies. Clinical Implications: When accuracy of RPDs are considered, digital technologies tested presented similar results to those of conventional manufacturing method except for minor and major connector areas which necessitates further improvement.

Clinical Performance of Complete-Arch Implant- Supported Rehabilitations Using Monolithic Lithium Disilicate Restorations Bonded to CAD/CAM Titanium and Zirconia Frameworks up to 5 Years.

This clinical study evaluated the survival of monolithic lithium disilicate (ML) (IPS Emax, Ivoclar Vivadent) restorations bonded to complete-arch CAD/CAM made titanium or zirconia frameworks. Between August 2007 and December 2009, 15 patients (7 female, 8 male; mean age: 56.8 years old) received 30 implant-supported screw-retained rehabilitations with ML restorations cemented to CAD/CAM made titanium (T) (n=6) or zirconia (Z) frameworks (n=24) adhesively (Multilink Automix, RelyX Unicem) and followed up until December 2015. The evaluation protocol involved technical failures (chipping, debonding or fracture of crown/framework, screw loosening), Californian Dental Association (CDA) quality criteria (Romeo: Excellent; Sierra: Acceptable; Tango: Retrievable; Victor: Not acceptable) and biological failures (mucositis, peri-implantitis). Mean observation time was 60.3 months. No implants were lost, and all the prostheses were in situ. Four mechanical failures occurred in the form of minor chipping (n=3 in ML-Z, n=1 in ML-T) and major fracture in ML crown (n=1 in ML-Z). Romeo scores (N=370) decreased until final observation (N=347) and 23 Sierra scores were given to the restorations. Mucositis was observed in 3 patients and peri-implantitis in one patient. Complete-arch implant-borne FDPs made of monolithic lithium disilicate bonded to titanium or zirconia frameworks could be a promising alternative.

Assessment of Biomechanical Behavior of Endodontically Treated Premolar Teeth Restored with Novel Endocrown System.

OBJECTIVE: Despite the increased popularity of endocrowns, there is no clear consensus considering their effectiveness to restore severely-destructed endodontically treated premolars. This study aimed to assess the biomechanical behavior of endodontically treated maxillary first premolars restored with a novel endocrown system compared to the conventional one. MATERIALS AND METHODS: Twenty sound human maxillary first premolars were collected. After endodontic treatment, they were divided into 2 groups (n=10) according to the system used for endocrown fabrication. Group C (Control): conventional monolithic IPS e.max CAD endocrowns. Group P: novel bi-layered endocrowns (Pekkton ivory coping veneered with cemented IPS e.max CAD). All specimens were subjected to 10000 thermal cycles followed by 240000 dynamic load cycles. Surviving specimens were subjected to fracture resistance test followed by qualitative analysis using Stereomicroscopy and Scanning Electron Microscopy. RESULTS: A significantly higher load was observed for Group P (1831.37 ± 240.69 N) than Group C (1433.47 ± 174.39 N) (p ⟨ 0.001). A statistically significant difference was observed considering the failure mode (p = 0.036), with more favorable fractures detected with Group P. CONCLUSIONS: The tested novel endocrown system improved the biomechanical behavior of the tooth/ restoration complex in the restored endodontically treated maxillary first premolars. CLINICAL SIGNIFICANCE: The tested novel endocrown system with a PEKK coping veneered with cemented IPS e.max CAD can be considered a promising option for restoration of severely-destructed endodontically treated premolar teeth. It can be considered as a conservative alternative option to the conventional treatment modalities.

Evaluating the Bond Strength of a Polymer Infiltrated Ceramic Network to Zirconia Using the Crossbeam Push-Off Method.

Porcelains and glass-ceramics have been used to produce CAD-milled veneers and crowns for zirconia copings and implant-abutments. This study evaluated the bondstrength of a polymer-infiltrated-ceramic-network to zirconia using two adhesive cement systems: Panavia 21 and Multilink Automix. Lithium disilicate and feldspathic porcelain were also tested as reference CAD-On materials. Long beams (3x6x40 mm³) of zirconia and short beams (3x6x15 mm³) of the CAD-On materials were prepared. Zirconia and each CAD-On material were bonded in a crossbeam arrangement and subjected to a modified tensile bond-strength test. Half of the samples in each group (n=10) were tested 5 days after bonding (baseline) and the remaining (n=10) underwent aging (50,000 thermocycles at 5°C and 55°C) prior to bond-strength testing. The effects of material, cement, and aging on the tensile bond-strength were tested using a three-way ANOVA. The reference lithium disilicate/Multilink system showed no significant differences in bond strength compared to polymer-infiltrated-ceramic-network and porcelain. The long-term retention of polymer-infiltrated-ceramic-network was not statistically different compared to the baseline values and the two reference materials. With comparable bond strength between all materials, polymer-infiltrated-ceramic-network is the favorable choice for CAD-On to zirconia copings and implant-abutments due to its superior resistance to fatigue fracture relative to porcelain.

Two-Year Survival of Ceramic Endocrowns and Partial Coverage Ceramic Restorations with Fiber Post: A 2-Year Double-Blind Randomized Clinical Trial.

PURPOSE: This double-blind randomized clinical trial (RCT) aimed to evaluate the 2-year survival rates of endocrowns and partial coverage ceramic restorations (PCCR) with fiber posts. MATERIAL AND METHODS: Forty (40) participants fulfilled the elegibility criteria, and they were randomly allocated in 2 groups: Endocrown or PCCR+post. The survival rates were assessed based on USPHS modified and radiographic examinations. A Chi-square test was used to assess the distribution of characteristics between groups. Kaplan-Meier and Log-rank tests were used to estimate the survival rate. To evaluate the association between survival of the restorations and the explanatory variables, the Multivariate Cox regression model was used. Only variables presenting p⟨0.20 were maintained in final model (α= 0.05). RESULTS: The highest 2-year survival rates were recorded for the Endocrown group (100%), whereas the PCCR+post group exhibited the lowest performance (66.7%). Most of the restoration failures was due to lack of marginal adaption, fracture, and recurrent caries. Cox Regression unadjusted analysis showed that only type of restoration presented a significant effect (p⟨0.20). Thus, adjusted analysis was not performed. CONCLUSIONS: Endocrowns appear to be a promising conservative restorative option and to be feasible and reliable approach restoring endodontically.

Water as Veneering Modeling Liquid Affects Microhardness of Glassy Matrix Veneering Ceramic.

PURPOSE/AIM: To evaluate the effect of different veneering liquids used for modeling on microhardness, fracture toughness and biaxial flexural strength of a glass-veneering ceramic. MATERIAL AND METHODS: The manufacturer recommended modeling liquid (ML), distilled water (DW), isopropyl alcohol (IA), 0.5% (P05), 1% (P1), and 2% (P2) polyethylene glycol solutions were mixed with feldspathic ceramic powder to form disc-shaped samples (n=20, 15 mm × 1.2 mm). After sintering, samples were mirror-polished and subjected to Vickers indentation (n=5) for measurement of microhardness and fracture toughness. The remaining 15 samples from each group were subjected to biaxial flexural strength. Data were subjected to one-way ANOVA and Weibull analysis. RESULTS: The microhardness was affected by veneering liquid (p=0.002): DW promoted higher microhardness values than ML and IA. Fracture toughness (p=0.301) and flexural strength (p=0.930) were not affected by the veneering liquid but Weibull parameters were affected. All groups presented surface pores under high magnification. CONCLUSION: Even though the use of DW led to higher values of surface microhardness than the ML, all obtained values are inside the range of enamel microhardness values reported in the literature. Such parameters may affect antagonist wear and should be reported in clinical trials.

Arthroscopic versus Mini-Open Rotator Cuff Repair: Should We Ignore the Mini-Open Surgery?

PURPOSE OF THE STUDY To compare the functional and radiological results of the total arthroscopic treatment (TAT) performed due to the rotator cuff (RC) tear problem with the results of the arthroscopically assisted mini-open surgery (AAMOS). MATERIAL AND METHODS This study conducted over a two-year period included all had TAT or AAMOS. Patients were included in the study if they had undergone arthroscopic or mini-open rotator cuff repair, with a minimum of 2 years' follow-up. Patients were divided into two groups in terms of the surgical technique performed. Patients who had TAT was included into the group 1 and, AAMOS group 2. Exclusion criteria included other significant intra-articular pathology such as SLAP lesions or glenohumeral arthrosis, previous rotator cuff surgery, massive rotator cuff tears (>5 cm), and neurologic disorders such as brachial plexopathy or suprascapular neuropathy. Every patient underwent magnetic resonance imaging evaluation before surgery and at last follow-up after surgery. Acromion typed of patients were recorded. Patients were questioned for ASES and Constant score. RESULTS Fifty-eight shoulders were included in the study. Twenty-eight patients were female and 30 were male. The mean age was 55.63 ± 8.06 years. Both groups had 29 patients per each. Mean follow-up period was 26.26 ± 11.46 months. There was no statistically significant difference between the mean age and gender distribution of the groups (p > 0.05). No statistically significant difference in the follow-up period between two groups (p > 0.05). No statistically significant difference was found between the postoperative ASES measurements between the two groups (p > 0.05). There was no statistically significant difference in postoperative Constant measurements between the two groups (p > 0.05). There was no statistically significant difference between the Acromion types between the two groups (p > 0.05). No statistically significant difference was found between the both groups in terms of accompanying shoulder pathology and AC joint degeneration (p > 0.05). In the postoperative MRIs of the patients, 7 patients in the Group 2 and 6 patients in the Group 1 were found to have recurrent tears. No statistically significant difference was found (p > 0.05). DISCUSSION When compared their patients who underwent RC repair by AAMOS intervention with those treated with TAT intervention and stated that the results were satisfactory for both groups and close to each other during their 2-year follow-up regardless of the tear diameter. Rotator cuff repairing with TAT is becoming a popular method of shoulder surgery. Initial reports of outcomes with this technique have indicated similar results when compared with open techniques, with less perioperative morbidity. Patients with RC tears treated by TAR, the shoulder range of motion was achieved in a shorter time and the rate of development of fibrous ankylosis was found to be lower. We performed the same configuration for the repair technique that may avoid to differ the results. Additionlay, all patients in study had the same rehabilitation protocol not to differ the results. Our study demonstrated similar results, with no differences noted in clinical outcomes between the TAT and the AAMOS for all scoring scales evaluated. Our experience with TAT notes a steep learning curve for proper technique. Certainly, surgeons may attempt a TAT, knowing that the patient's long-term outcome will not differ if the AAMOS is needed. CONCLUSIONS It must be kept in mind that both surgical methods may provide satisfactory results; the decision regarding which method should be used must be based on the skills, experience and technical oppurtunities of the orthopedic surgeon. However, any of the surgical technique is chosen, smilar excellent clinical results can be achieved. Key words: rotator cuff, mini-open surgery, total arthroscopic repair, cuff tear, Constant score, ASES score.

Accuracy, Reliability and Clinical Implications of Static Compared to Quantifiable Occlusal Indicators.

OBJECTIVE: This literature review summarizes the properties, advantages, limitations, and clinical implications of employing static occlusal indicators compared to quantifiable digital occlusal indicators during occlusal adjustments. METHOD: An electronic database search of dental literature was carried out in PubMed/MEDLINE using the key words Occlusal Indicators, Occlusal Assessment, Static, Reliability, Dynamic, Repeatability, Validity and Clinical Accuracy. A total of 231 papers were isolated, with 129 papers considered for review. RESULTS: The included papers were grouped by Static and Dynamic Occlusal indicators. The numbers of papers in the Static Group was extremely low (only 20 papers) compared to The Dynamic group (T-Scan: 89; Dental Prescale: 28; Intraoral Scanners:17). CONCLUSION: Little evidence supports the use of static occlusal indicators due to their high degree of subjectivity required during implementation. However, much scientific evidence supports the use of T-Scan, as it measures relative occlusal forces and timing objectively, accurately, and repeatedly. For the improvement of Occlusal Practice, Subjective Interpretation using Static occlusal indicators should be replaced with digital ones for objective measurements. CLINICAL RELEVANCE: The computerized occlusal analysis system is well studied and has the capacity to provide precise time and force sequencing information to objectively evaluate occlusal contacts for improved treatment outcome.

Effect of Thickness and Shade of Resin and Ceramic- Based Hybrid Materials on Color Masking Abilities and Optical Performance of CAD/CAM Materials.

Scientific data analysing color masking abilities of chairside CAD/CAM materials is lacking. The purpose of this in-vitro study was to evaluate the thickness and shade influence of three materials on their optical behaviour. Three materials: a) LD: Lithium disilicate glass ceramic (Emax, Ivoclar Vivadent), b) LDS: Lithium-disilicate-strengthened aluminosilicate glass ceramic (N!ce, Straumann) and c) RNC: Resin Nanoceramic (Lava Ultimate, 3M ESPE) were polished in different shades (A1,A2,A3) and thicknesses (0.1- 1.2mm). Specimens (N=108; n=36 per group) (12x12x1mm3) were positioned on resin composite base (Clearfil AP-X, Kuraray) in shade A3. Spectrophotometric measurements were performed and the parameters thickness, shade and material were analysed using three-way ANOVA, and pairwise T-tests (P-values ⟨ 0.05). Both the shade (p⟨0.001) and the interaction of material in correlation to thickness (p⟨0.001) were significant. Shade value A1-A3 comparisons were significant A1 vs. A2 (p=0.045); A2 vs. A3 (p=0.002); A1 vs. A3 (p⟨0.001)). A significant correlation of the material and thickness was observed when comparing LD and LDS (p=0.007) at the thickness of 0.1-0.4 mm. Masking abilities were influenced by material and thickness choice. Reinforced glass ceramics showed the best results in the smallest thickness tested (0.1-0.4 mm). LDS could be considered as an advantageous alternative in minimal-invasive cases.