Effect of preparation design on fracture strength of compromised molars restored with direct composite resin restorations: An in vitro and finite element analysis study.

STATEMENT OF PROBLEM: More data are needed on the influence of preparation design on the fracture strength, failure type, repairability, and polymerization-induced cracks of molar teeth restored with direct composite resin restorations. PURPOSE: This in vitro and finite element analysis study investigated the effect of different preparation designs on fracture strength, failure type, repairability, tooth deformation, and the formation of polymerization-induced cracks of compromised molars restored with direct composite resin restorations. MATERIAL AND METHODS: Human molars (n=64) were randomly assigned to 4 different preparation designs: undermined inlay (UI), extended inlay (EI), restricted overlay (RO), and extended overlay (EO). The teeth were restored using direct composite resin and subjected to artificial thermomechanical aging in a mastication simulator, followed by load-to-failure testing. Three-dimensional (3D) finite element analysis was conducted to assess tooth deformation. Polymerization-induced cracks were evaluated using optical microscopy and transillumination. The fracture strength data were analyzed using a Kruskal-Wallis test, while the failure mode, repairability, and polymerization cracks were analyzed using the Fisher exact test (α=.05). RESULTS: All specimens withstood thermomechanical aging, and no statistically significant difference in fracture strength was observed among the 4 preparation designs (P>.05). The finite element analysis showed differences in tooth deformation, but no correlation was observed with in vitro fracture resistance. The RO and EO groups presented significantly more destructive failures compared with the UI and EI groups (P<.01). The RO group had significantly fewer repairable failures than the UI and EI groups (P=.024). A correlation was found between higher frequencies of repairability and higher tooth deformation. A significant correlation between the increase in microfractures and preparation design was observed (P<.01), with the UI group exhibiting a higher increase in microfracture size compared with the EO group (P<.05). CONCLUSIONS: No influence of preparation design on the fracture strength of compromised molars restored with direct composite resin restorations was evident in this study, but the failure mode of cusp coverage restorations was more destructive and often less repairable. The finite element analysis showed more tooth deformation in inlay preparations, with lower stresses within the root, leading to more reparable fractures. Since cusp coverage direct composite resin restorations fractured in a more destructive manner, this study suggests that even a tooth with undermined cusps should be restored without cusp coverage.

Wear at the implant-framework interface between titanium implant platform and the additively manufactured titanium and cobalt-chromium frameworks.

PURPOSE: To measure the wear at the implant interface between the Grade 4 titanium (Ti) of the implant and frameworks fabricated using two additively manufactured alloys (Ti alloy and cobalt-chromium [Co-Cr]) pre- and post-artificial aging. MATERIAL AND METHODS: Three-unit frameworks supported by two implants were additively manufactured (Atlantis; Dentsply Sirona) using Ti and Co-Cr dental alloys. Two implants (OsseoSpeed EV, Astra Tech; Dentsply Sirona) were torqued on each non-engaging framework. The assembled implant-frameworks were secured into polyurethane foam blocks. Groups were created based on the material and surface assessed: framework (Ti-framework and Co-Cr-framework groups) and implant (Ti-implant group). Two subgroups were created depending on the location: premolar (PM) and molar (M). Computed tomography images were obtained pre- (as manufactured) and post-simulated mastication procedures. The pre- and post-simulated mastication files of each specimen were aligned using the best-fit algorithm using a metrology program. Wear was measured by calculating the volumetric discrepancies at the implant interface on 64 measurement points per area analyzed. Three-way ANOVA and Tukey tests were used to analyze the data (α = 0.05). RESULTS: The mean volumetric discrepancy values ranged from 0.8 to 3.1 µm among all the subgroups tested. The group (framework vs. implant) (p < 0.001) and tooth location (p < 0.001) were significant factors of the mean volumetric discrepancy values obtained. The framework group presented with significantly lower volumetric discrepancy mean values (1 µm) compared with the implant group (3 µm), whereas the premolar area obtained significantly lower mean volumetric discrepancy values (1.9 µm) compared with the molar location (2.3 µm). CONCLUSIONS: Volumetric discrepancies were found at the implant-framework interface tested between the pre- and post-artificial aging measurements ranging from 1 to 3 µm after 1,200,000 cyclic loading that simulated approximately 12 months of function.

Influence of different printing orientations and post-polymerization time on the translucency of three-dimensional (3D) printed denture base resins.

PURPOSE: To evaluate the effect of different printing orientations and post-polymerization time with thermal cycling on the translucency of 3D-printed denture base resins. METHODS: Heat-polymerized (HP) acrylic resin specimens were fabricated and 3D-printed denture base materials (NextDent, ASIGA, FormLabs) were printed with different printing orientations (0, 45, 90 degrees) and subjected to different post-polymerization times (15-, 30-, 60-, and 90-min). All specimens were polished and immersed in distilled water for 1 day at 37°C. CIEDE2000 was used to measure the translucency parameters (TP00) before and after thermal cycling (5000 cycles) recording the color parameters (L*, a*, b*) against a black and white background using a spectrophotometer. k-factors ANOVA followed by post hoc Tukey's test (α = .05) was performed for statistical analysis. RESULTS: The k-factors ANOVA test showed a significant effect of resin material, post-polymerization time, and printing orientation on translucency (p < 0.001). In comparison to HP, all 3D-printed resins showed lower translucency with all post-polymerization times and printing orientation (p < 0.001) except FormLabs resin (p > 0.05). For all 3D-printed resins, the translucency increased, with increasing the post-polymerization time (p < 0.001) and 60- and 90-min showed the highest translucency. For printing orientation, 90 and 45 degrees significantly showed high translucency in comparison to 0 degrees (p < 0.001). FormLabs showed significantly higher translucency when compared with NextDent and ASIGA per respective printing orientation and post-polymerization time. The translucency significantly decreased after thermal cycling for all tested resins (p < 0.001). CONCLUSION: The findings of this study demonstrated that the translucency of 3D-printed resins is influenced by the printing orientation, post-polymerization time, and resin type. As a result, choosing a resin type, and printing orientation, with a longer post-polymerization time should be considered since it may improve the esthetic appearance of the 3D-printed resins.

Adhesion of tooth fragment after trauma: effect of adhesion strategy and storage in the rescue box.

This study aims to investigate the impact of storage conditions for crown fragments (specifically, whether they were stored within a tooth rescue box or in tap water) on their adhesion to fractured teeth when subjected to two different adhesive systems (namely, total etch and self etch). Sixty maxillary premolars were sectioned to obtain tooth fragments. These fragments were stored briefly (2 hours) and reattached in the following groups: Group 1 (fragments stored in tooth rescue box and reattached with etch and rinse (E&R) technique), Group 2 (fragments stored in tap water and reattached with E&R technique), Group 3 (fragments stored in tooth rescue box and reattached with self-etch (SE) technique), and Group 4 (fragments stored in tap water and reattached SE technique). After reattachment, the bonded tooth fragments underwent thermal cycling (500 cycles, 5-55 °C) and bond strength testing using a universal testing machine. Two-way Analysis of Variance (ANOVA) and Tukey's tests were used for bond strength comparison (p ≤ 0.05). A two-parameter Weibull distribution was conducted to evaluate the reliability of the storage medium and adhesion modality on bond strength. The results showed that measured shear bond values (MPa ± Standard deviation (SD); arranged in descending order) for each group were: Group 2 (Tap water/E&R = 6.5 ± 2.1), Group 1 (Rescue box/E&R = 6.0 ± 2.5), Group 4 (Tap water/E&R = 5.1 ± 2.8), and Group 3 (Rescue box/SE = 3.6 ± 3.2). Significant differences were found only between Groups 2 and 3 (p = 0.002). In conclusion, storing crown fragments in a tooth rescue box did not significantly affect the shear bond strength of the restored tooth. However, fragments reattached using the self-etch technique showed comparable shear bond strength but a higher rate of adhesive failures compared to the E&R technique.

Short-term effect of material type and thickness of occlusal splints on maximum bite force and sleep quality in patients with sleep bruxism: a randomized controlled clinical trial.

OBJECTIVE: To evaluate the short-term effects of hard and soft splints of different thicknesses on maximum bite force (MBF) and sleep quality (SQ) in participants with sleep bruxism (SB). METHODS: One-hundred-fifteen patients were randomly allocated to five groups: Groups H2(Hard splint-2 mm), H3(Hard splint-3 mm), S2(Soft splint-2 mm), S3(Soft splint-3 mm), and C (control). Outcomes were MBF (assessed with a digital gnathodynamometer) and SQ (assessed with the Pittsburgh Sleep Quality Index). Measurements were performed at T0 (before the splints), T1 (1-month follow-up), and T2 (2-months follow-up). Data were analyzed using one-way analysis of variance(ANOVA), Tukey's HSD, and chi-square tests (alpha = 0.05). RESULTS: At T1, the highest MBF values were observed in group H3 (658.01 ± 22.6 N), while the lowest in group S2 (585.45 ± 8.68 N). For T2, the highest values were obtained in H3 group (676.85 ± 21.9 N), and the lowest in group S2 (565.65 ± 10.9 N) (p < 0.05).For SQ, groups S2 and S3 revealed the lowest PSQI values at T1 (9.1; 9.6) and T2 (9; 9.5) (p < 0.001). CONCLUSIONS: The short-term use of both 2 and 3-mm thick soft splints resulted in a decrease in MBF. Improvement in SQ in patients using soft splints was observed in the 1st month and was maintained in the 2nd month. CLINICAL RELEVANCE: This study provides insights on short-term clinical effects as regards to increased sleep quality and regulated maximum bite force as a function of splint material type and the thickness of the splint.

Evaluation of biochemical changes and treatment efficacy in patients with bruxism following botulinum toxin or splint therapy: a randomized clinical trial.

OBJECTIVES: This clinical study aims to analyze the levels of cortisol, dehydroepiandrosterone (DHEA), and tumor necrosis factor alpha (TNF-α) in the gingival crevicular fluid (GCF) of persons with bruxism and to compare the efficacy of botulinum toxin (botox) and occlusal splint treatments through biomarkers. MATERIALS AND METHODS: A total of 40 patients with bruxism were selected according to the clinical examination and anamnesis of which 20 received occlusal splint treatment and 20 botox treatment. GCF samples were taken from the patients before and after treatment. Cortisol, DHEA, and TNF-α levels were measured by enzyme-linked immunosorbent assay test. The change in measurements between time and groups and the time-group interaction were tested by repeated measures ANOVA. RESULTS: There was a statistically significant difference between the cortisol levels before and after treatment in both groups (p = 0.001). In individuals with bruxism, a statistically significant decrease in cortisol levels was observed after both treatments (p < 0.05), while DHEA levels increased after treatment but were not statistically significant (p > 0.05). There was no statistically significant difference between TNF-α intra-group measurements (p > 0.05). CONCLUSIONS: Stress and inflammatory biomarkers were found to be associated with bruxism. Cortisol levels decreased in people with bruxism after treatment with both occlusal splint and botox. CLINICAL RELEVANCE: Both splint and botox treatments were effective for bruxism by reducing the stress levels.

Mechanical and chemical characterization of contemporary occlusal splint materials fabricated with different methods: a systematic review.

OBJECTIVE: To systematically review studies on various occlusal splint materials and describe their mechanical and chemical properties. METHODS: MEDLINE (PubMed), Scopus, and Web of Science searches were conducted for in vitro studies focusing on occlusal splint materials. Two reviewers performed an assessment of the identified studies and data abstraction independently, and this was complimented by an additional hand search. The articles were limited to those in the English language that were published between January 1st, 2012, and December 1st, 2022. RESULTS: The initial search yielded 405 search results of which 274 were selected for full-text review following abstract evaluation. 250 articles that did not meet the inclusion criteria were excluded, and the remaining 25 articles (with 1 article identified from the reference lists of included articles) providing mechanical and chemical values were used in this review. Poly methyl methacrylate (PMMA) -based occlusal splint materials showed the highest values in terms of hardness, wear resistance, flexural strength, flexural modulus, e-modulus, and fracture toughness. The material group with the highest water sorption and water solubility was 3D printed (PR) splint materials. In addition, the lowest degree of double bond conversion was also observed in this group of materials. CONCLUSIONS: The outcome of this review suggests that mechanically and chemically acceptable properties can be attained with PMMA-based occlusal splint materials using both conventional and digital production methods. PR splint materials should not be considered as the primary choice for long-term treatments due to their low mechanical and chemical properties. CLINICAL RELEVANCE: This review provides clinical recommendations for selecting the appropriate material and fabrication method for occlusal splints while taking the patients' needs and the materials´ mechanical and chemical properties into account.

Three-year clinical evaluation of zirconia and zirconia-reinforced lithium silicate crowns with minimally invasive vertical preparation technique.

OBJECTIVES: Large part of the tooth is required to be removed during crown preparation. A minimally invasive method for preparing single crowns is required to increase the durability of teeth. The aim of this study was to evaluate the clinical performance of two ceramic systems fabricated with minimally invasive vertical preparation. MATERIALS AND METHODS: Forty endodontically treated maxillary premolars were prepared with vertical preparation and received temporary crowns for a period of 21 days. Twenty zirconia-reinforced lithium silicate (Celtra Duo HT, Dentsply Sirona, Germany) and 20 monolithic high translucency zirconia (Katana HT, Kuarary Noritake, Japan) crowns were fabricated by CAD/CAM and cemented with dual-polymerizing luting resin. The crowns were evaluated clinically and radiographically for 36 months following modified FDI criteria. Statistical analysis was conducted with t Student test (Cochran Q). RESULTS: Over the follow-up period, there was no need to replace any of the study's crowns. The overall survival rate of the 40 crowns was 100% according to the Kaplan-Meier survival method. The clinical quality of all crowns and the patient's satisfaction were high. No caries was detected and no adverse soft tissue reactions around the crowns were observed. Periodontal probing depth was reported to be increased at mesial and distal sites more than the facial one in the 36-month follow-up with no statistically significant difference between both materials (P = 0.186). CONCLUSIONS: Zirconia and zirconia-reinforced lithium silicate could be used as a material for restoration of teeth prepared with vertical preparation technique. Both ceramic materials achieved good esthetic results, promotes healthy and stable soft tissues with no mechanical complications after 3 years of clinical evaluation. CLINICAL RELEVANCE: Monolithic high translucency zirconia and zirconia-reinforced lithium silicate ceramics can be used for the restorations of minimal invasive vertical preparation in premolar area with 0.5 mm margin thickness.

Selective removal to soft dentine or selective removal to firm dentine for deep caries lesions in permanent posterior teeth: a randomized controlled clinical trial up to 2 years.

OBJECTIVES: The aim of this randomized clinical trial was to compare selective removal to soft dentin (SRSD) and selective removal to firm dentin (SRFD) in permanent teeth. The primary outcome of the study was to compare the success rates of the two caries removal techniques. The secondary outcome of the study was to investigate whether or not calcium silicate-based material (CS) had an effect on the success rate of the treatment. MATERIALS AND METHODS: Between November 2018 and March 2020, patients with deep caries lesions were invited to participate in the study. Posterior teeth (N = 165) with primary caries lesion radiographically extending ¾ of dentin and positive response to cold test were randomly selected. A total of 134 participants meeting the inclusion criteria were randomized to SRSD and SRFD (control) groups. After the caries removal procedure, teeth with exposed pulps were assigned to the pulp exposure (PE) group, and the SRSD group was further divided into test 1 (with CS) and test 2 groups (without CS). Success was defined as a positive response to the cold test, a negative response to percussion, the absence of pain, an abscess, a fistula, and periapical alterations. Fisher-Freeman-Halton exact tests, Kaplan-Meier survival analysis, and the log-rank tests were performed for comparisons between groups. RESULTS: No statistically significant difference was found between the success rates of test 1 (100%) and test 2 (93.5%) groups, whereas the proportion of success in control (82.4%) and PE (84%) groups were significantly lower when compared with test groups (p = 0.024; p < 0.05) at the end of 2-year follow-up. CONCLUSIONS: SRSD had a higher success rate when compared to SRFD to treat deep carious lesions after 2 years of follow-up. The use of CS material after SRSD as a liner had no effect on the treatment outcome. CLINICAL RELEVANCE: SRSD with good coronal sealing might be recommended without CS application for the treatment of deep caries lesions in permanent teeth. TRIAL REGISTRATION: Clinical trial registration number NCT04052685 (08/09/2019).

An investigation on fatigue, fracture resistance, and color properties of aesthetic CAD/CAM monolithic ceramics.

OBJECTIVES: To evaluate and compare fracture resistance, translucency, and color reproducibility, as well as the effect of aging on the fracture load and color stability of novel monolithic CAD/CAM ceramics. MATERIALS AND METHODS: One hundred crowns of uniform thickness were milled from five ceramic blocks (n = 20): partially crystallized lithium disilicate (PLD) and fully crystallized lithium disilicate (FLD), lithium metasilicate (LMS), 4Y-TZP (SMZ), and 5Y-TZP (UMZ) monolithic zirconia. PLD crowns were glazed, LMS was fired, and FLD was polished. SMZ and UMZ crowns were sintered and polished. Crowns were adhesively cemented to epoxy dies. Half of the crowns (n = 10) were subjected to 1.200.000 load cycles with thermal cycling. Color space values L, a, b defined by the Commission Internationale de l´Eclairage (CIELAB) were measured before and after aging, and (∆E) was calculated. Both aged and non-aged specimens were loaded until fracture in a universal testing machine and the fracture load was recorded. X-ray diffraction (XRD) and scanning electron microscope (SEM) fractographic analysis were carried out on fractured fragments of representative samples. For translucency and color reproducibility, 50 rectangular-shaped specimens were fabricated and processed as described previously. Color values were measured over black and white backgrounds, and the translucency parameter (TP) was computed. Using the shade verification mode, (∆E) to shade A3 was calculated. Data were statistically analyzed using one-way and two-way ANOVA, and t-test. RESULTS: Aging did not affect fracture resistance significantly (p > 0.05). The highest mean fracture load was obtained for the SMZ and UMZ. A significant color change was observed after aging in all groups. The highest TP was noted for FLD. SMZ and UMZ had the best shade match. CONCLUSIONS: Zirconia showed higher fracture resistance and color stability than lithium silicate ceramics. Lithium silicate ceramics were more translucent. The experimental FLD demonstrated high translucency. CLINICAL RELEVANCE: Tested ceramics showed sufficient stability to withstand masticatory forces. Characterization of final restorations might be mandatory for better color match.

Surface modification of zirconia or lithium disilicate-reinforced glass ceramic by laser texturing to increase the adhesion of prosthetic surfaces to resin cements: an integrative review.

OBJECTIVE: The purpose of this study was to perform an integrative review on laser texturing the inner surface of lithium disilicate-reinforced glass ceramic or zirconia to increase their bond strength to resin-matrix cements. MATERIALS AND METHOD: A bibliographic review was performed on PubMed using the following search terms: "zirconia" OR "lithium disilicate" AND "laser" AND "surface" OR "roughness" AND "bond strength" AND "luting agent" OR "resin cement." Studies published in English language until March 15, 2023, were selected regarding the purpose of this study. RESULTS: A total of fifty-six studies were identified althoug thirteen studies were selected. The findings revealed that zirconia surfaces were significantly modified after laser irradiation resulting in macro-scale aligned retentive regions with depth values ranging from 50 to 120 µm. Average roughness values of laser-textured zirconia by Er,Cr:YSGG laser (~ 0.83 µm) were quite similar when compared to grit-blasted zirconia surfaces (~ 0.9 µm) although roughness increased up to 2.4 µm depending on the laser type and parameters. Lithium disilicate-reinforced glass ceramics textured with Er:YAG revealed an average roughness of around 3.5 µm while surfaces textured using Nd:YAG laser revealed an average roughness of 2.69 µm; that was quite similar to the roughness values recorded for etched surfaces (2.64 µm). The shear bond strength (SBS) values of zirconia surfaces textured on Nd:YVO4 laser irradiation were slightly higher (~ 33.5 MPa) than those recorded for grit-blasted zirconia surfaces (28 MPa). Laser-textured zirconia surfaces on CO2 laser revealed higher SBS values (18.1 ±0.8 MPa) than those (9.1 ± 0.56 MPa) recorded for untreated zirconia surfaces. On lithium disilicate-reinforced glass ceramics, higher SBS values to resin-matrix cements were recorded for specimens textured with a combination of fractional CO2 laser irradiation and HF acid etching (~ 22-24 MPa) when compared with grit-blasted specimens (12.2 MPa). Another study revealed SBS values at around 27.5 MPa for Er:YAG-textured lithium disilicate-reinforced glass ceramics to resin-matrix cements. CONCLUSIONS: The laser irradiation at high power increases the roughness of the inner surface of lithium disilicate-reinforced glass ceramic or zirconia leading to an enhanced bond strength to resin-matrix cements. Thus, the laser type and irradiation parameters can be adjusted to enhance the macro- and micro-scale retention of zirconia and glass ceramic surfaces to resin-matrix cements. CLINICAL RELEVANCE: Alternative methods for surface modification of lithium disilicate-reinforced glass ceramic and zirconia surfaces have been assessed to provide proper morphological aspects for enhanced adhesion to resin-matrix cements. An increase in the bond strength of glass ceramics or zirconia to resin-matrix cements can improve the long-term performance of cemented prosthetic structures in the oral cavity.

Root canal disinfection and maintenance of the remnant tooth tissues by using grape seed and cranberry extracts.

The purpose of this study was to perform an integrative review on the effects of cranberry and grape seed extracts concerning the disinfection of root canals maintaining the strength of the remnant tooth tissues' structure. A bibliographical search was carried out on the PubMed electronic platform using the following key terms: cranberry, grape seed, vaccinium macrocarpon, proanthocyanidin, antibacterial, antimicrobial, decontamination, disinfection, bacteria removal, bacteria eradication, bacteria elimination, endodontic, root canal, faecalis, and strength. The inclusion criteria involved articles published in the English language, until March, 2022, reporting the antibacterial effect of grape seed and cranberry extracts. Of 185 studies identified, 13 studies were selected for the present review. The grape seed extract (GSE), composed of proanthocyanidins, showed an antioxidant activity against the main bacteria found in endodontic secondary infection. The percentage of bacteria removal was recorded at around 96.97% by using GSE. Studies on cranberry extracts, which are composed of proanthocyanidins, revealed antimicrobial effects against bacteria related to periodontitis and dental caries. Additionally, GSE or cranberry allowed the dentin collagen cross-linking that preserved the 3D collagen network leading to the maintenance of the strength of the remnant tooth structure. However, the contaminated smear layer could not be removed by using only GSE or cranberry. Cranberry extracts and GSE revealed a significant antimicrobial activity in endodontic disinfection without changing the mechanical properties of the remnant dentin tissues. Furthermore, those components can be associated with traditional compounds to enhance their antimicrobial effects and eliminate the smear layer.

Toxicity of resin-matrix cements in contact with fibroblast or mesenchymal cells.

The main aim of this study was to perform an integrative review on the toxic effects of resin-matrix cements and their products in contact with fibroblasts or mesenchymal cells. A bibliographic search was performed on PubMed using the following search terms: "cytotoxicity" AND "fibroblast" OR "epithelial" OR "mesenchymal" AND "polymerization" OR "degree of conversion" OR "methacrylate" OR "monomer" AND "resin cement" OR "resin-based cement". The initial search in the available database yielded a total of 277 articles of which 21 articles were included in this review. A decrease in the viability of mouse fibroblasts ranged between 13 and 15% that was recorded for different resin-matrix cements after light curing exposure for 20 s. The viability of human fibroblasts was recorded at 83.11% after light curing for 20 s that increased up to 90.9% after light curing exposure for 40 s. Most of the studies linked the highest toxicity levels when the cells were in contact with Bis-GMA followed by UDMA, TEGDMA and HEMA. Resin-matrix cements cause a cytotoxic reaction when in contact with fibroblasts or mesenchymal cells due to the release of monomers from the polymeric matrix. The amount of monomers released from the resin matrix and their cytotoxicity depends on the polymerization parameters.

Fracture strength and energy-dispersive spectroscopy analysis of 3-unit fixed partial dentures fabricated from different monolithic zirconia materials.

STATEMENT OF PROBLEM: Mastication forces in different regions affect the survival of multiunit posterior restorations. The fracture strength of 3-unit posterior monolithic zirconia fixed partial dentures (FPDs) and their fracture patterns require investigation. PURPOSE: The purpose of this in vitro study was to evaluate and compare the fracture strength and fracture pattern of 3-unit posterior FPDs fabricated from different monolithic zirconia materials. MATERIAL AND METHODS: Thirty 3-unit FPDs were fabricated from BruxZir, FireZr, and Upcera (n=10 per group). Energy-dispersive spectroscopy analysis was performed on 2 selected specimens from each group. All specimens were exposed to a mastication simulator for 1.2×106 cycles and then monotonically loaded to fracture at a crosshead speed of 1 mm/min. The surfaces of a selected fractured specimen were examined at magnifications of ×25 and ×500 with scanning electron microscopy. Conformity to normal distribution was evaluated with the Shapiro-Wilk test. One-way analysis of variance was used to compare the normally distributed initial crack formation load F initial (Fi) and catastrophic failure strength F maximum (Fm) means by group. Weibull statistics were calculated by using the maximum likelihood estimation method. The chi-square test was used to compare shape and scale parameters (α=.05). RESULTS: The mean Fm values were fail1878.9 N for Upcera, 2177.8 N for BruxZir, and 2229.4 N for FireZr. Upcera and BruxZir showed statistically significant differences for the Fm mean values (P=.039). The differences between the fracture type distributions according to the groups were statistically similar (P>.05). For Fi, Upcera presented the highest Weibull modulus value (2.199), FireZr had the lowest (1.594), while for Fm, BruxZir had the highest Weibull modulus value (9.267) and FireZr the lowest (6.572). CONCLUSIONS: Using the zirconia materials BruxZir, FireZr, and Upcera resulted in high Fm values after aging procedures. With all materials, the fractures were most commonly found in the connector areas in the tested FPDs.

Effect of prerestorative short-term clear aligner therapy in restorative treatment planning.

STATEMENT OF PROBLEM: One of the major challenges in restorative dentistry is to provide optimal esthetics in a minimally invasive way. The optimization of dental esthetics and function is directly related to the position and alignment of the anterior teeth, but whether prerestorative clear aligner therapy will enhance esthetics and minimize restorative needs is unclear. PURPOSE: The purpose of this clinical study was to evaluate the effect of prerestorative maxillary and mandibular second premolar to second premolar clear aligner therapy in minimizing the need for restorative treatment. MATERIAL AND METHODS: Fifty adult patients treated with clear aligners (Invisalign Go; Align Technology) were included in this study. Previously generated 3-dimensional orthodontic simulations and clinical photographs in the ClinCheck/6.0 software program were used. Three restorative treatment plans for each participant were generated for initial (no aligners), Express (after using 7 aligners), and Lite Packages (after using 20 aligners) by 2 blinded restorative dentistry instructors. The maxillary and mandibular teeth in the smile-line (to the second premolars) were included. Assessment criteria were the estimated number of restorations, restoration surfaces and preparations and incisal edge inclusion, and the need for gingival leveling. The Friedman test and Cochran Q test were used for statistical analyses (α=.05). RESULTS: A strong positive correlation was found between the 2 instructors (P<.001). Estimated number of restorations (10 [3 to 16]a) decreased significantly for Express (6 [0 to 14]b) and Lite Packages (4 [0 to 8]c) (P<.001). The estimated number of restoration surfaces (28.5 [9 to 48]a) decreased significantly for Express (15 [0 to 42]b) and Lite Packages (9.5 [0 to 24]c) (P<.001). While the estimated number of teeth to be prepared for recontouring (7 [0 to 16]a) was significantly less for Express (3 [0 to 10]b) and Lite Packages (0 [0 to 4]c) (P<.001), the incisal edge inclusion (10 [3 to 16]a) was significantly less for Express (6 [0 to 14]b) and Lite Packages (4 [0 to 8]c) (P<.001). The need for gingival leveling (26 [52%]a) decreased significantly for Express (20 [40%]a) and Lite Packages (7 [14%]b) (P<.001). CONCLUSIONS: Prerestorative short-term clear aligner therapy might conserve tooth structure and reduce the number of restorations. The application of the Invisalign Lite Package was more effective than the Invisalign Express Package for second premolar to second premolar alignment.

Effect of additional reference objects on accuracy of five intraoral scanners in partially and completely edentulous jaws: An in vitro study.

STATEMENT OF PROBLEM: The effect of additional reference objects on the accuracy of different intraoral scanners for partially and completely edentulous patients has not been investigated sufficiently. PURPOSE: The purpose of this in vitro study was to evaluate the effect of an additional reference object in the form of additional artificial landmarks on the trueness and precision of different intraoral scanners in partially and completely edentulous areas. MATERIAL AND METHODS: Partially and completely edentulous models with 2 and 4 implants (BLT, RC, Institut Straumann AG), respectively, were used in the study. For the digital scan, scan bodies (CARES Mono Scanbody) were attached, and reference data obtained by using industrial scanners. Ten digital scans of the same model were made with each intraoral scanner: PRIMESCAN, TRIOS 3, TRIOS 4, Carestream 3600, and Medit. Then, additional artificial landmarks were attached, and 10 more intraoral scans were made with each device. Computer-aided design files of the scan bodies were aligned to obtain 3-dimensional surfaces with reference and test scanners. Trueness and precision of distance, angulations, and vertical shift between scan bodies were estimated. The Mann-Whitney Wilcoxon or Student 2-sample t test was applied to estimate statistically significant differences between groups (α=.05). RESULTS: In the partially edentulous model, distance trueness mean ±standard deviation values ranged from -46.7 ±15.4 µm (TRIOS 3) to 392.1 ±314.3 µm (Medit) in models without additional artificial landmarks. When additional artificial landmarks were applied, trueness of distance mean ±standard deviation values ranged between -35 ±13 µm (TRIOS 4) and 117.7 ±232.3 µm (CARESTREAM). Trueness mean ±standard deviation values of angulation varied from -0.0 ±0.5 degrees (CARESTREAM) to 0.2 ±0.0 degrees (PRIMESCAN) without additional artificial landmarks and from 0.0 ±0.2 degrees (TRIOS 3) to 0.4 ±0.5 degrees (CARESTREAM) with additional artificial landmarks. Vertical shift trueness measurements varied from -108 ±47.1 µm (TRIOS 4) to 107.2 ±103.5 µm (Medit) without additional artificial landmarks and from -15.0 ±45.0 µm (CARESTREAM) to -86.9 ±42.1 µm (TRIOS 4) with additional artificial landmarks. The additional artificial landmark technique improved the trueness of all measured parameters for the 5 tested intraoral scanners. No statistically significant differences were found among models with or without additional artificial landmarks, except for Medit in all parameters and PRIMESCAN in angle measurements (P<.05). The best precision for distance was found with TRIOS 3 and with PRIMESCAN for angulation and vertical shift. Larger deviations were observed in the completely edentulous situation. The effect of additional artificial landmarks was limited when the accuracy parameters of digital scans were considered. CONCLUSIONS: Scans with and without additional artificial landmarks of partially edentulous conditions scanned by any of the intraoral scanners tested did not influence precision and trueness, except for Medit i500 in the distance and vertical shift parameters and CARESTREAM3600 in vertical shift. Precision and trueness of digital scans of completely edentulous areas were affected, except for Medit i500 for distance, PRIMESCAN and TRIOS 4 for angle, and all systems except TRIOS 4 for vertical shift precision.

Trueness and precision of complete-arch photogrammetry implant scanning assessed with a coordinate-measuring machine.

STATEMENT OF PROBLEM: Photogrammetry technology has been used for the digitalization of multiple dental implants, but its trueness and precision remain uncertain. PURPOSE: The purpose of this in vitro investigation was to compare the accuracy (trueness and precision) of multisite implant recordings between the conventional method and a photogrammetry dental system. MATERIAL AND METHODS: A definitive cast of an edentulous maxilla with 6 implant abutment replicas was tested. Two different recording methods were compared, the conventional technique and a photogrammetry digital scan (n=10). For the conventional group, the impression copings were splinted to an additively manufactured cobalt-chromium metal with autopolymerizing acrylic resin, followed by recording the maxillary edentulous arch with an elastomeric impression using an additively manufactured open custom tray. For the photogrammetry group, a scan body was placed on each implant abutment replica, followed by the photogrammetry digital scan. A coordinate-measuring machine was selected to assess the linear, angular, and 3-dimensional discrepancies between the implant abutment replica positions of the reference cast and the specimens by using a computer-aided design program. The Shapiro-Wilk test showed that the data were not normally distributed. The Mann-Whitney U test was used to analyze the data (α=.05). RESULTS: The conventional group obtained an overall accuracy (trueness ±precision) value of 18.40 ±6.81 µm, whereas the photogrammetry group showed an overall scanning accuracy value of 20.15 ±25.41 µm. Significant differences on the discrepancies on the x axis (U=1380.00, P=.027), z axis (U=601.00, P<.001), XZ angle (U=869.00, P<.001), and YZ angle (U=788.00, P<.001) were observed when the measurements of the 2 groups were compared. Furthermore, significant 3-dimensional discrepancy for implant 1 (U=0.00, P<.001), implant 2 (U=0.00, P<.001), implant 3 (U=6.00, P<.001), and implant 6 (U=9.00, P<.001) were computed between the groups. CONCLUSIONS: The conventional method obtained statistically significant higher overall accuracy values compared with the photogrammetry system tested, with a trueness difference of 1.8 µm and a precision difference of 18.6 µm between the systems. The conventional method transferred the implant abutment positions with a uniform 3-dimensional discrepancy, but the photogrammetry system obtained an uneven overall discrepancy among the implant abutment positions.

Clinical performance of direct composite resin versus indirect restorations on endodontically treated posterior teeth: A systematic review and meta-analysis.

STATEMENT OF PROBLEM: High-level evidence concerning the restoration of endodontically treated posterior teeth by means of direct composite resin or indirect restorations is lacking. PURPOSE: The purpose of this systematic review and meta-analysis was to analyze the current literature on the direct and indirect restoration of endodontically treated posterior teeth. MATERIAL AND METHODS: Databases MEDLINE, CENTRAL, and EMBASE were screened. Risk of bias was assessed by using the ROB2 tool for RCTs and the ROBINS-I tool for prospective and retrospective clinical studies. Randomized clinical trials (RCTs) and prospective and retrospective studies comparing direct composite resin and indirect restorations on endodontically treated posterior teeth were included. Outcomes were tooth and restoration survival. A meta-analysis was conducted for tooth retention and restorative success. RESULTS: Twenty-two studies were included (2 RCTs, 3 prospective, and 17 retrospective). Over the short term (2.5 to 3 years), low-quality evidence suggested no difference in tooth survival. For the prospective and retrospective clinical trials, the overall risk of bias was serious to critical from the risk of confounding because of a difference in restorative indication: Direct restorations were fabricated when one marginal ridge remained or when tooth prognosis was unfavorable. For short-term restorative success, low-quality evidence suggested no difference between the direct and indirect restorations. CONCLUSIONS: For the short term (2.5 to 3 years), low-quality evidence suggests no difference in tooth survival or restoration quality. To assess the influence of the type of restoration on the survival and restorative success of endodontically treated posterior teeth, clinical trials that control for the amount of coronal tooth tissue and other baseline characteristics are needed.

Comparison of wear and fracture resistance of additively and subtractively manufactured screw-retained, implant-supported crowns.

STATEMENT OF PROBLEM: Additively manufactured resins indicated for fixed definitive prostheses have been recently marketed. However, knowledge on their wear and fracture resistance when fabricated as screw-retained, implant-supported crowns and subjected to artificial aging is limited. PURPOSE: The purpose of this in vitro study was to evaluate the volume loss, maximum wear depth, and fracture resistance of screw-retained implant-supported crowns after thermomechanical aging when fabricated using additively and subtractively manufactured materials. MATERIAL AND METHODS: Two additively manufactured composite resins (Crowntec [CT] and VarseoSmile Crown Plus [VS]) and 2 subtractively manufactured materials (1 reinforced composite resin, Brilliant Crios [BC] and 1 polymer-infiltrated ceramic network, Vita Enamic [EN]) were used to fabricate standardized screw-retained, implant-supported crowns. After fabrication, the crowns were cemented on titanium base abutments and then tightened to implants embedded in acrylic resin. A laser scanner with a triangular displacement sensor (LAS-20) was used to digitize the preaging state of the crowns. Then, all crowns were subjected to thermomechanical aging (1.2 million cycles under 50 N) and rescanned. A metrology-grade analysis software program (Geomagic Control X 2020.1) was used to superimpose postaging scans over preaging scans to calculate the volume loss (mm3) and maximum wear depth (mm). Finally, all crowns were subjected to a fracture resistance test. Fracture resistance and volume loss were evaluated by using 1-way analysis of variance and Tukey Honestly significant difference (HSD) tests, whereas the Kruskal-Wallis and Dunn tests were used to analyze maximum wear depth. Chi-square tests were used to evaluate the Weibull modulus and characteristic strength data (α=.05). RESULTS: Material type affected the tested parameters (P<.001). CT and VS had higher volume loss and maximum wear depth than BC and EN (P<.001). EN had the highest fracture resistance among tested materials (P<.001), whereas BC had higher fracture resistance than CT (P=.011). The differences among tested materials were not significant when the Weibull modulus was considered (P=.199); however, VE had the highest characteristic strength (P<.001). CONCLUSIONS: Additively manufactured screw-retained, implant-supported crowns had higher volume loss and maximum wear depth. All materials had fracture resistance values higher than the previously reported masticatory forces of the premolar region; however, the higher characteristic strength of the subtractively manufactured polymer-infiltrated ceramic network may indicate its resistance to mechanical complications.

Artificial intelligence models for tooth-supported fixed and removable prosthodontics: A systematic review.

STATEMENT OF PROBLEM: Artificial intelligence applications are increasing in prosthodontics. Still, the current development and performance of artificial intelligence in prosthodontic applications has not yet been systematically documented and analyzed. PURPOSE: The purpose of this systematic review was to assess the performance of the artificial intelligence models in prosthodontics for tooth shade selection, automation of restoration design, mapping the tooth preparation finishing line, optimizing the manufacturing casting, predicting facial changes in patients with removable prostheses, and designing removable partial dentures. MATERIAL AND METHODS: An electronic systematic review was performed in MEDLINE/PubMed, EMBASE, Web of Science, Cochrane, and Scopus. A manual search was also conducted. Studies with artificial intelligence models were selected based on 6 criteria: tooth shade selection, automated fabrication of dental restorations, mapping the finishing line of tooth preparations, optimizing the manufacturing casting process, predicting facial changes in patients with removable prostheses, and designing removable partial dentures. Two investigators independently evaluated the quality assessment of the studies by applying the Joanna Briggs Institute Critical Appraisal Checklist for Quasi-Experimental Studies (nonrandomized experimental studies). A third investigator was consulted to resolve lack of consensus. RESULTS: A total of 36 articles were reviewed and classified into 6 groups based on the application of the artificial intelligence model. One article reported on the development of an artificial intelligence model for tooth shade selection, reporting better shade matching than with conventional visual selection; 14 articles reported on the feasibility of automated design of dental restorations using different artificial intelligence models; 1 artificial intelligence model was able to mark the margin line without manual interaction with an average accuracy ranging from 90.6% to 97.4%; 2 investigations developed artificial intelligence algorithms for optimizing the manufacturing casting process, reporting an improvement of the design process, minimizing the porosity on the cast metal, and reducing the overall manufacturing time; 1 study proposed an artificial intelligence model that was able to predict facial changes in patients using removable prostheses; and 17 investigations that developed clinical decision support, expert systems for designing removable partial dentures for clinicians and educational purposes, computer-aided learning with video interactive programs for student learning, and automated removable partial denture design. CONCLUSIONS: Artificial intelligence models have shown the potential for providing a reliable diagnostic tool for tooth shade selection, automated restoration design, mapping the preparation finishing line, optimizing the manufacturing casting, predicting facial changes in patients with removable prostheses, and designing removable partial dentures, but they are still in development. Additional studies are needed to further develop and assess their clinical performance.