Synthesis and characterization of Y3+-doped TiO2 nanocomposites for photocatalytic applications.

The TiO(2).[Y(2)O(3)](x) (x = 0.1-0.4) nanocomposites (NCs) with an average particle size of 74 nm were prepared by the method of chemical co-precipitation followed by hydrolysis (CPH). Their visible light photocatalytic activity was investigated for the degradation of congo red (CR) dye. All NCs showed improved degradation as compared to the polycrystalline samples of similar compositions prepared by the solid-state reaction (SSR) route (average particle size of a few micrometers), as well as to the pure TiO(2). The better photocatalytic activity of the NCs was attributed to their smaller particle size. Another comparison of the results with those obtained with Zn(2+)/Fe(3+) ions co-doped TiO(2) NCs, under similar experimental conditions, revealed that in the Y(3+)-doped NCs, particle size might not be the only factor responsible for the improved photocatalytic properties. It was concluded that the Y(3+) ion-mediated suppression of the unwanted e(-)/h(+) recombination could be the possible factor leading to additional enhancement.

Electrochemical Characterization and Determination of Phenol and Chlorophenols by Voltammetry at Single Wall Carbon Nanotube/Poly(3,4-ethylenedioxythiophene) Modified Screen Printed Carbon Electrode.

Screen printed carbon electrode (SPCE) has been modified with single wall carbon nanotube/poly(3,4-ethylenedioxythiophene) (SWCNT/PEDOT) composites for the determination of phenol and chlorophenols (phenol, 4-chlorophenol, 2,4-dichlorophenol, and 2,4,6-trichlorophenol). The effect of the modifiers on the electrode characteristics was evaluated and the responses were optimized for the voltammetric determination of phenol and chlorophenols. The parameters affecting the responses such as pH, scan rate, and stability were studied. The analytical performance of the SWCNT/PEDOT/SPCE using cyclic voltammetry was tested and found to be impressive. Under these conditions, the designed electrode showed a good performance for the voltammetric measurements of the phenolic compounds. The modified SPCE, when it is compared with other enzymatic and nonenzymatic sensors, showed a wider dynamic range for the detection of the phenolic compounds. The modified SPCE was used for the quantification of phenol in water samples. The results suggest that the method is quite useful for analyzing and monitoring phenols and chlorophenols.

Modelling of the impedimetric responses of an aflatoxin B(1) immunosensor prepared on an electrosynthetic polyaniline platform.

Aflatoxins are a group of mycotoxins that have deleterious effects on humans and are produced during fungal infection of plants or plant products. An electrochemical immunosensor for the determination of aflatoxin B(1) (AFB(1)) was developed with AFB(1)antibody (AFB(1)-Ab) immobilized on Pt electrodes modified with polyaniline (PANi) and polystyrene sulphonic acid (PSSA). Impedimetric analysis shows that the electron transfer resistances of the Pt/PANi-PSSA electrode, the Pt/PANi-PSSA/AFB(1)-Ab immunosensor and Pt/PANi-PSSA/AFB(1)-Ab incubated in bovine serum albumin (BSA) were 0.458, 720 and 1,066 kOmega, respectively. These results indicate that electrochemical impedance spectroscopy (EIS) is a suitable method for monitoring the change in electron transfer resistance associated with the immobilization of the antibody. Modelling of EIS data gave equivalent circuits which showed that the electron transfer resistance increased from 0.458 kOmega for the Pt/PANi-PSSA electrode to 1,066 kOmega for the Pt/PANi-PSSA/AFB(1)-Ab immunosensor, indicating that immobilization of the antibody and incubation in BSA introduced an electron transfer barrier. The AFB(1) immunosensor had a detection limit of 0.1 mg/L and a sensitivity of 869.6 kOmega L/mg.

Voltammetric determination of niclosamide at a glassy carbon electrode.

A very sensitive and selective procedure was developed for the determination of niclosamide based on square-wave voltammetry at a glassy carbon electrode. Cyclic voltammetry was used to investigate the electrochemical reduction of niclosamide at a glassy carbon electrode. Niclosamide was first irreversibly reduced from NO2 to NHOH at -0.659 V in aqueous buffer solution of pH 8.5. Reversible and well defined peaks at -0.164 V and -0.195 V (vs. Ag/AgCl) were obtained that are responsible for two electron peaks between NHOH and NO. Following optimisation of the voltammetric parameters, pH and reproducibility, a linear calibration curve over the range 5 x 10(-8)-1 x 10(-6) mol dm(-3) was achieved. The detection limit was found to be 2.05 x 10(-8) mol dm(-3) niclosamide. For eight successive determinations of 5 x 10(-7) mol dm(-3) niclosamide, a relative standard deviation of 2.4% was obtained. This voltammetric method was applied to the direct determination of niclosamide in tablets. The results of the analysis suggest that the proposed method has promise for the routine determination of niclosamide in the products examined.

(Bio)sensors based on manganese dioxide-modified carbon substrates: retrospections, further improvements and applications.

An overview is presented which summarizes our accomplishment in the development of sensors and biosensors based on heterogenous carbon electrodes modified with manganese dioxide. Brief account of each sensor and biosensor has been given and example of real sample applications provided where appropriate.