A comparative study of the risk assessment and heavy metal contamination of coastal sediments in the Red sea, Egypt, between the cities of El-Quseir and Safaga.

This study aimed to assess the influence of pollution on the quality of sediments and the risks associated with El-Qusier and Safaga Cities, Red Sea, Egypt, during 2021, divided into four sectors, using multiple pollution indices. To achieve that, we evaluated the metal pollution index (MPI), contamination factor (Cf), pollution load index (PLI), contamination security index (CSI), and anthropogenicity (Anp%). Moreover, carcinogenic and non-carcinogenic risks are used for human health hazards. Results indicated that Mn and Fe recorded the highest concentrations, whereas Cd had the lowest. El-Quseir City sediments were found the following metal ions: Fe > Mn > Ni > Zn > Cu > Co > Pb > Cd, where the order in the Safaga City was: Fe > Mn > Zn > Ni > Cu > Pb > Co > Cd. MPI > 1, this is alarming in the study area due to heavy metal pollution. In addition, Cf < 1 in all metals except Cd with contamination degree CD ranged from low to considerable contamination in El-Qusier city. In contrast, contamination ranged from significant to very high in Safaga city. PLI < 1 is lower than the reference at all monitored stations. CSI values ranged from relatively low to moderate. Besides Cd, data reflect each element's low environmental danger (EriMe40). This study's risk index (RI) is low to moderate in Sector 1 and high to extremely high in Sector 2. HQ and HI index < 1 means it is safe for human health in order: HI ingestion > HI dermal. CSR for different pathways was recorded as dermal > ingestion, in which total CSR for all paths is considered harmful, and the cancer risk is troublesome and higher than the reference ranges of 1 × 10-6-1 × 10-4. In conclusion, the examined heavy metals provide environmental hazards across the assessed locations.

Utilization of aquatic biomass as biosorbent for sustainable production of high surface area, nano- microporous, for removing two dyes from wastewater.

The majority of environmental researchers are becoming increasingly concerned with the manufacture of inexpensive adsorbents for the detoxification of industrial effluents. To address one of the significant and well-known pollution issues with certain drains that act as hotspots and contribute to coastal pollution in Alexandria, this study aims to develop an economical, ecologically friendly sorbent. This study assessed the efficacy of a biomass-coated magnetic composite and a magnetic active adsorbent for the removal of two dyes from an industrially contaminated sewer using a wetland plant (Phragmites australis). Using magnetic biosorbent, the biosorption of Xylenol orange and Congo red ions from polluted drain discharge in Abu Qir Bay was evaluated in the current study. Using scanning electron microscopy imaging and Fourier transform infra-red analysis; the surface function and morphology of the nano-biosorbent were examined. At room temperature, the effects of initial dye concentration, pH, contact time, and nano-biosorbent concentration have all been investigated. The greatest percentages that nano-biosorbent can remove from Congo red and Xylenol orange are 97% and 47%, respectively. The removal of the initial Congo red concentration varied from 42 to 97%, while the removal of the initial Xylenol orange concentration varied from 30 to 47%. The adsorption capacity was shown to be strongly pH-dependent; capacity dose as pH value increased, with pH 10 being the ideal pH for Congo red and pH 6 being the ideal pH value for Xylenol orange. The adsorption capacity for Congo red varied between 0.96 and 3.36 and the adsorption capacity for Xylenol orange varied between 0.18 and 17.58. The removal capacity decreased from 3.36 to 0.96 mg/g when the biosorbent dosage was increased from 0.05 to 0.5 g/L for Congo red, in case of Xylenol orange, the removal capacity increased from 0.18 to 17.58 mg/g when the biosorbent dosage was increased from 0.05 to 0.5 g/L. The removal capacity of Congo red increases quickly with time and varied from 1.66 to 1.88 of contact time; while the removal capacity of Xylenol orange varied between 3.08 and 4.62 of contact time. For the dyes under study, kinetics and adsorption equilibrium were examined. Within 180 min, the equilibrium was attained because to the quick adsorption process. For Congo red and Xylenol orange, the highest adsorption capacities were 3.36 and 17.58 mg g-1, respectively. The equilibrium data were assessed using a number of isotherm models, including Langmuir, Freundlich, BET, and Tempkin, while the kinetic data were examined using a variety of kinetic models, including pseudo-first- and pseudo-second-order equations. The pseudo-second-order equation provides the greatest accuracy for the kinetic data and Langmuir model is the closest fit for the equilibrium data.

Algal Extracts for Green Synthesis of Zinc Oxide Nanoparticles: Promising Approach for Algae Bioremediation.

Zinc oxide nanoparticles (ZnO-NPs) possess unique properties, making them a popular material across various industries. However, traditional methods of synthesizing ZnO-NPs are associated with environmental and health risks due to the use of harmful chemicals. As a result, the development of eco-friendly manufacturing practices, such as green-synthesis methodologies, has gained momentum. Green synthesis of ZnO-NPs using biological substrates offers several advantages over conventional approaches, such as cost-effectiveness, simplicity of scaling up, and reduced environmental impact. While both dried dead and living biomasses can be used for synthesis, the extracellular mode is more commonly employed. Although several biological substrates have been successfully utilized for the green production of ZnO-NPs, large-scale production remains challenging due to the complexity of biological extracts. In addition, ZnO-NPs have significant potential for photocatalysis and adsorption in the remediation of industrial effluents. The ease of use, efficacy, quick oxidation, cost-effectiveness, and reduced synthesis of harmful byproducts make them a promising tool in this field. This review aims to describe the different biological substrate sources and technologies used in the green synthesis of ZnO-NPs and their impact on properties. Traditional synthesis methods using harmful chemicals limit their clinical field of use. However, the emergence of algae as a promising substrate for creating safe, biocompatible, non-toxic, economic, and ecological synthesis techniques is gaining momentum. Future research is required to explore the potential of other algae species for biogenic synthesis. Moreover, this review focuses on how green synthesis of ZnO-NPs using biological substrates offers a viable alternative to traditional methods. Moreover, the use of these nanoparticles for industrial-effluent remediation is a promising field for future research.

Equilibrium and Kinetic Modeling of Crystal Violet Dye Adsorption by a Marine Diatom, Skeletonema costatum.

Significant efforts have been made to improve adsorbents capable of eliminating pollutants from aqueous solutions, making it simple and quick to separate from the treated solution. In the current study, the removal of Crystal Violet Dye (CVD) from an aqueous synthetic solution onto a marine diatom alga, Skeletonema costatum, was investigated. Different experiments were conducted as a function of different pH, contact time, adsorbent dosage, temperature, and initial CVD concentration. The highest adsorption efficiency (98%) was obtained at 0.4 g of S. costatum, pH 3, and a contact time of 120 min, at 25 °C. Furthermore, Fourier-transform infrared spectroscopy (FTIR) results display that binding of CVD on S. costatum may occur by electrostatic and complexation reactions. Moreover, the Brunauer-Emmett-Teller surface area analysis (BET) obtained was 87.17 m2 g-1, which, in addition to a scanning electron microscope (SEM), reveals large pores that could enhance the uptake of large molecules. However, the equilibrium adsorption models were conducted by Halsey, Langmuir, Freundlich, Henderson, and Tempkin isotherm. In addition, multilayer adsorption isotherm best described the uptake of CVD onto S. costatum. The maximum monolayer adsorption capacity (qmax) was 6.410 mg g-1. Moreover, thermodynamic parameters of the adsorption studies suggested that the uptake of CVD onto S. costatum was endothermic and spontaneous. The pseudo-first-order, pseudo-second-order, and intra-particle diffusion kinetic equations were applied to model the adsorption kinetic data. It was seen that the kinetics of the adsorption may be described using pseudo-second-order kinetic equations. Finally, the present work concluded that the marine diatom alga S. costatum is suitable as a natural material for the adsorption of CVD.

The Using of Nanoparticles of Microalgae in Remediation of Toxic Dye from Industrial Wastewater: Kinetic and Isotherm Studies.

Batch adsorption experiments were carried out to study the removal of the toxic Methylene Blue Dye (MBD) from synthetic aqueous solutions using the nanoparticles form of Arthrospira platensis NIOF17/003. The adsorption capacity of the adsorbent for MBD was investigated using different amounts of A. platensis nanoparticles at different contact times, temperatures, pH, and MBD initial concentrations in the synthetic aqueous solution. In addition, A. platensis nanoparticles were characterized using Electron Microscopy (SEM), Brunauer-Emmett-Teller (BET), Fourier Transform Infrared (FTIR), and Ultraviolet spectra (UV) techniques. The optimum removal of MBD was found at a concentration of 0.4 g A. platensis nanoparticles. A. platensis nanoparticles remove 93% of MBD in 5 min (under agitation conditions at 150 rpm). The highest adsorption capacity was found by the Langmuir model to be 58.8 mg g-1. It is an endothermic process with spontaneity increasing with temperature. The probable mechanism for the adsorption is chemisorption via surface-active charges in the initial phase, which is followed by physical sorption by occupying pores of A. platensis. MBD adsorption by A. platensis follows pseudo-second-order kinetics. The Freundlich and Langmuir models fit well with the experimental data. The adsorption experiments suggested that the regeneration of the adsorbents was possible for repeated use, especially regarding MBD up to 65.8% after three cycles, which proves it can be easily recycled. In conclusion, the nanoparticles of A. platensis have a significant adsorption potential in the removal of MBD from effluent wastewater.

Do Red Seaweed Nanoparticles Enhance Bioremediation Capacity of Toxic Dyes from Aqueous Solution?

Based on their functional groups, the use of various seaweed forms in phytoremediation has recently gained significant eco-friendly importance. The objective of this study was to determine whether a novel, sustainable, and ecologically acceptable adsorbent could be employed to remove toxic textile dye (Ismate Violet 2R (IV2R)) from an aqueous solution. The low-cost adsorbent was prepared from the nanoparticles form of the native red seaweed species, Pterocladia capillacea. Before and after the adsorption procedure, comprehensive characterization experiments on the bio-adsorbent were carried out, including BET, SEM, FTIR, UV, and dynamic light scattering (DLS) examination. The adsorption performance of the prepared nano-Pterocladia capillacea was optimized by adjusting operating parameters such as the initial dye concentration of 60 mg L-1, pH of 2, and contact time of 15 min, all of which were obtained by batch experiments in the lab. At the optimum conditions, the prepared adsorbent had maximum removal effectiveness of 87.2%. Most typical kinetics and isotherm models were used to test the experimental results. The equilibrium data fit well with the Langmuir isotherm model, with comparatively higher R2 values and fewer standard errors, while the pseudo-second-order kinetic model fits better with a decent correlation coefficient. Thermodynamic parameters revealed that the sorption process on nano-alga was exothermic and spontaneous.

Green Synthesis of Zinc Oxide Nanoparticles Using Red Seaweed for the Elimination of Organic Toxic Dye from an Aqueous Solution.

This study aims to produce green zinc oxide nanoparticles (ZnO-NPs) derived from red seaweed (Pterocladia Capillacea) and evaluate their potential to absorb Ismate violet 2R (IV2R) ions from an aqueous solution. UV-vis spectrophotometry, Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and a Brunauer-Emmett-Teller surface area analysis (BET) were used to analyze the structural, morphological, and optical features of the synthesized nanoparticles. The change in color of the chemical solution revealed the formation of zinc oxide nanoparticles. The FTIR examination confirmed the synthesis of both Zn and ZnO nanoparticle powder, with a BET surface area of 113.751 m2 g-1 and an average pore size of 2.527 nm for the synthesized adsorbent. Furthermore, the maximum removal effectiveness of IV2R was 99% when 0.08 g ZnO-NPs was applied at a pH of 6, a temperature of 55 °C, and a contact time of 120 min. The dye adsorption capacity of the ZnO-NPs was 72.24 mg g-1. The adsorption process was also controlled by the Freundlich adsorption model and pseudo-second-order reaction kinetics. The adsorption of IV2R ions onto the ZnO-NPs could be represented as a nonideal and reversible sorption process of a nonuniform surface, according to Freundlich adsorption isotherms. In addition, the constant values of the model parameters were determined using various nonlinear regression error functions. Moreover, thermodynamic parameters such as entropy change, enthalpy change, and free energy change were investigated; the adsorption process was spontaneous and endothermic. The high capacity of the ZnO-NPs synthesized by red seaweed promotes them as promising substances for applications in water treatment for the removal of IV2R dye from aqueous systems.

Dried Brown Seaweed's Phytoremediation Potential for Methylene Blue Dye Removal from Aquatic Environments.

The dried form of the brown seaweed Sargassum latifolium was tested for its ability to remove toxic Methylene Blue Dye (MBD) ions from aqueous synthetic solutions and industrial wastewater effluents. In a batch adsorption experiment, different initial concentrations of MBD (5, 10, 20, 30, and 40 mg L-1), sorbent dosages (0.025, 0.05, 0.1, 0.2, 0.3, 0.4, and 0.5 g L-1), contact time (5, 10, 15, 30, 60, 120 min), pH (3, 5, 8, 10, and 12), and temperature (30, 40, 50, 60 °C) were observed. Dried powder of S. latifolium was characterized before and after adsorption of MBD using different techniques, such as FTIR, SEM, UV visible spectral examination, and BET techniques. The BET surface area suggests the formation of S. latifolium was 111.65 m2 g-1, and the average pore size was 2.19 nm. The obtained results showed that at an MBD concentration of 40 mg L-1, the adsorption was rapid in the first 5, 10, and 15 min of contact time, and an equilibrium was reached in about 60 and 120 min for the adsorption. At the optimum temperature of 30 °C and the adsorbent dose of 0.1 g L-1, approximately 94.88% of MBD were removed. To find the best-fit isotherm model, the error function equations are applied to the isotherm model findings. Both Tempkin and Freundlich isotherm models could appropriate the equilibrium data, as well as the pseudo 2nd order kinetics model due to high correlation coefficients (R2). Thermodynamic and Freundlich model parameters were assessed and showed that the mechanism of the sorption process occurs by an endothermic and physical process. According to the results of the experiments, S. latifolium is a promising environmentally friendly approach for eliminating MBD from the aqueous solution that is also cost-effective. This technology could be useful in addressing the rising demand for adsorbents employed in environmental protection processes.

Studying the Adsorptive Behavior of Poly(Acrylonitrile-co-Styrene) and Carbon Nanotubes (Nanocomposites) Impregnated with Adsorbent Materials towards Methyl Orange Dye.

In this study, a polymeric (acrylonitrile-co-styrene) P(AN-co-St) composite was impregnated with adsorbents, such as sulfonated and multiwall carbon nanotubes (MWCNTs), to increase the adsorptive characteristics of the nanocomposite upon the removal of methyl orange (MO) dye under different conditions. A novel nanocomposite copolymer mixture of P(AN-co-St) and SP(AN-co-St) was used. MWCNTs were prepared by a low-cost chemical vapor deposition (CVD) process. Variation in MO adsorption onto the three nanocomposites was examined in an aqueous solution via the batch technique with respect to contact time, initial MO concentration, adsorbent dosage, pH, and temperature. The surface of the nanocomposites was characterized by a scanning electron microscope (SEM), particle size distribution (PSD), Fourier transform infrared (FTIR), and Raman analysis. The experimental data showed that the efficiency of P(AN-co-St)/ MWCNT removal increased under the conditions of an acidic pH (3 and 5) with an agitation speed of 140 rpm, a sorbent weight of 0.01 g, and 20 mg of initial dye. The maximum sorption capacities were 121.95, 48.78, and 47.84 mg g-1 for the P(AN-co-St)/ MWCNTs, SP(AN-co-St), and P(AN-co-St) composites, respectively, as assessed by the Langmuir model. Additional isotherm models, such as the Freundlich, Temkin, and Halsey models, were used to examine the experimental data. A pseudo-second-order model was found to be more fitting for describing the sorption.

Ammonia Bioremediation from Aquaculture Wastewater Effluents Using Arthrospira platensis NIOF17/003: Impact of Biodiesel Residue and Potential of Ammonia-Loaded Biomass as Rotifer Feed.

The present work evaluated the capability of Arthrospira platensis complete biomass (ACDW) and the lipid-free biomass (LFB) to remove ammonium ions (NH4+) from aquaculture wastewater discharge. Under controlled conditions in flasks filled with 100 mL of distilled water (synthetic aqueous solution), a batch process ion-exchange was conducted by changing the main parameters including contact times (15, 30, 45, 60, 120, and 180 min), initial ammonium ion concentrations (10, 20, 30, 40, 50, and 100 mg·L-1), and initial pH levels (2, 4, 6, 8, and 10) at various dosages of ACDW and LFB as adsorbents (0.02, 0.04, 0.06, 0.08, and 0.1 g). After lab optimization, ammonia removal from real aquaculture wastewater was also examined. The removal of ammonium using ACDW and LFB in the synthetic aqueous solution (64.24% and 89.68%, respectively) was higher than that of the real aquaculture effluents (25.70% and 37.80%, respectively). The data of IR and Raman spectroscopy confirmed the existence of various functional groups in the biomass of ACDW and LFB. The adsorption equilibrium isotherms were estimated using Freundlich, Langmuir, and Halsey models, providing an initial description of the ammonia elimination capacity of A. platensis. The experimental kinetic study was suitably fit by a pseudo-second-order equation. On the other hand, as a result of the treatment of real aquaculture wastewater (RAW) using LFB and ACDW, the bacterial counts of the LFB, ACDW, ACDW-RAW, and RAW groups were high (higher than 300 CFU), while the LFB-RAW group showed lower than 100 CFU. The current study is the first work reporting the potential of ammonia-loaded microalgae biomass as a feed source for the rotifer (Brachionus plicatilis). In general, our findings concluded that B. plicatilis was sensitive to A. platensis biomass loaded with ammonia concentrations. Overall, the results in this work showed that the biomass of A. platensis is a promising candidate for removing ammonia from aquaculture wastewater.

Potential Applications of Arthrospira platensis Lipid-Free Biomass in Bioremediation of Organic Dye from Industrial Textile Effluents and Its Influence on Marine Rotifer (Brachionus plicatilis).

Arthrospira platensis is one of the most important cultured microalgal species in the world. Arthrospira complete dry biomass (ACDB) has been reported as an interesting feedstock for many industries, including biodiesel production. The A. platensis by-product of biodiesel production (lipid-free biomass; LFB) is a source of proteins, functional molecules, and carbohydrates, and can also be reused in several applications. The current study investigated the efficiency of ACDB and LFB in bioremediation of dye (Ismate violet 2R, IV2R) from textile effluents. In addition, the potential of ACDB and LFB loaded by IV2R as a feed for Rotifer, Brachionus plicatilis, was examined. The surface of the adsorbents was characterized by SEM, FTIR, and Raman analysis to understand the adsorption mechanism. The batch sorption method was examined as a function of adsorbent dose (0.02-0.01 g L-1), solution initial concentration (10-100 mg L-1), pH (2-10), and contact time (15-180 min). The kinetic studies and adsorption isotherm models (Freundlich, Langmuir, Tempkin, and Halsey) were used to describe the interaction between dye and adsorbents. The results concluded that the adsorption process increased with increasing ACDB and LFB dose, contact time (120 min), initial IV2R concentration (10 mg L-1), and acidity pH (2 and 6, respectively). For the elimination of industrial textile wastewater, the ACDB and LFB sorbents have good elimination ability of a dye solution by 75.7% and 61.11%, respectively. The kinetic interaction between dye and adsorbents fitted well to Langmuir, Freundlish, and Halsey models for LFB, and Langmuir for ACDB at optimum conditions with R2 > 0.9. In addition, based on the bioassay study, the ACDB and LFB loaded by IV2R up to 0.02 g L-1 may be used as feed for the marine Rotifer B. plicatilis.