First Report on a Solvent-Free Preparation of Polymer Inclusion Membranes with an Ionic Liquid.

A novel and environmentally-friendly procedure for the preparation of polymer inclusion membranes (PIMs) containing an ionic liquid is presented for the first time. Traditionally, PIMs are prepared by a solvent casting method with the use of harmful organic solvents. Here we report a new solvent-free procedure based on a thermal-compression technique which involve the melting of the components of the PIM and the application of a high pressure to the melted specimen to form a flat-sheet film. In our study, we have tested different polymers, such as two cellulose derivatives as well as two thermoplastic polymers, polyurethane (TPU) and poli ε-caprolactone (PCL). The ionic liquid (IL) trioctylmethylammonium chloride (Aliquat 336) has been used to produce PIMs with a fixed composition of 70% polymer-30% IL (w/w). Both TPU and PCL polymers provide successful membranes, which have been thoroughly characterized. PIMs based on the polymer PCL showed a high stability. To test whether the properties of the IL were affected by the preparation conditions, the extraction ability of Aliquat 336 was investigated for both PCL and TPU membranes in terms of Cr(VI) extraction. Satisfactory values (90% extraction) were obtained for both membranes tested, showing this novel procedure as a green alternative for the preparation of PIMs with ILs.

Silencing of the potato StNAC103 gene enhances the accumulation of suberin polyester and associated wax in tuber skin.

Suberin and wax deposited in the cork (phellem) layer of the periderm form the lipophilic barrier that protects mature plant organs. Periderm lipids have been widely studied for their protective function with regards to dehydration and for how they respond to environmental stresses and wounding. However, despite advances in the biosynthetic pathways of suberin and associated wax, little is known about the regulation of their deposition. Here, we report on a potato NAC transcription factor gene, StNAC103, induced in the tuber phellem (skin). The StNAC103 promoter is active in cells undergoing suberization such as in the basal layer of the phellem, but also in the root apical meristem. Gene silencing in potato periderm correlates with an increase in the suberin and wax load, and specifically in alkanes, ω-hydroxyacids, diacids, ferulic acid, and primary alcohols. Concomitantly, silenced lines also showed up-regulation of key genes related to the biosynthesis and transport of suberin and wax in the tuber periderm. Taken together, our results suggest that StNAC103 has a role in the tight regulation of the formation of apoplastic barriers and is, to the best of our knowledge, the first candidate gene to be identified as being involved in the repression of suberin and wax deposition.

The Identification and Quantification of Suberin Monomers of Root and Tuber Periderm from Potato (Solanum tuberosum) as Fatty Acyl tert-Butyldimethylsilyl Derivatives.

INTRODUCTION: Protective plant lipophilic barriers such as suberin and cutin, with their associated waxes, are complex fatty acyl derived polyesters. Their precise chemical composition is valuable to understand the specific role of each compound to the physiological function of the barrier. OBJECTIVES: To develop a method for the compositional analysis of suberin and associated waxes by gas chromatography (GC) coupled to ion trap-mass spectrometry (IT-MS) using N-(tert-butyldimethylsilyl)-N-methyl-trifluoroacetamide (MTBSTFA) as sylilating reagent, and apply it to compare the suberin of the root and tuber periderm of potato (Solanum tuberosum). METHODOLOGY: Waxes and suberin monomers from root and periderm were extracted subsequently using organic solvents and by methanolysis, and subjected to MTBSTFA derivatisation. GC analyses of periderm extracts were used to optimise the chromatographic method and the compound identification. Quantitative data was obtained using external calibration curves. The method was fully validated and applied for suberin composition analyses of roots and periderm. RESULTS: Wax and suberin compounds were successfully separated and compound identification was based on the specific (M-57) and non-specific ions in mass spectra. The use of calibration curves built with different external standards provided quantitative accurate data and showed that suberin from root contains shorter chained fatty acyl derivatives and a relative predominance of α,ω-alkanedioic acids compared to that of the periderm. CONCLUSION: We present a method for the analysis of suberin and their associated waxes based on MTBSTFA derivatisation. Moreover, the characteristic root suberin composition may be the adaptive response to its specific regulation of permeability to water and gases. Copyright © 2016 John Wiley & Sons, Ltd.

Biochar-based polymeric film as sustainable and efficient sorptive phase for preconcentration of steroid hormones in environmental waters and wastewaters.

BACKGROUND: The environmental impact of sample preparation should be minimized through simplification of the procedures and the use of natural, renewable and/or reusable materials. In such scenario, thin-film microextraction fulfils the former criteria, as it enables few steps and miniaturization, thus small amount of extraction phase. At the same time, the use of sorbents such as biochars obtained from biomass waste is even more promoted due to their availability at low cost and increased life-cycle in a circular economy vision. However, it is not always easy to combine these criteria in sample preparation. RESULTS: A thin film microextraction was developed for the determination of steroids in aqueous samples, entailing a membrane made of cellulose triacetate and a wood-derived biochar (Nuchar®) as carbon precursor. Different characterization techniques showed the successful preparation, whereas the sorption kinetics experiments demonstrated that biochar is responsible for the extraction with the polymer acting as a smart support. After a study about membranes' composition in terms of biochar amounts (4 %, 10 %, 16 % wt) and type of synthesis set up, the ceramic 3D-mold was selected, achieving reproducible and ready-to-use membranes with composition fixed as 10 %. Different elution conditions, viz. type and time of agitation, type, composition and volume of eluent, were evaluated. The final microextraction followed by HPLC-MS/MS quantification was successfully validated in river and wastewater treatment plant effluent samples in terms of accuracy (R% 64-123 %, RSD<19 % in river; R% 61-118 %, RSD <18 % in effluent, n = 4), sensitivity (MQLs 0.2-8.5 ng L-1) and robustness. SIGNIFICANCE: This novel biochar-based polymeric film proved to be a valid and sustainable sorbent, in terms of extraction capability, ease of preparation and greenness. By comparison with literature and the greenness evaluation with the most recent metric tools, this method expands the potential applicability of the thin-film microextraction and opens up innovative scenarios for sustainable procedures entailing the use of biochars entrapped in bio-polymers.

A Comprehensive Study on the Effect of Plasticizers on the Characteristics of Polymer Inclusion Membranes (PIMs): Exploring Butyl Stearate as a Promising Alternative.

This study investigated the influence of various plasticizers commonly used in the manufacture of polymer inclusion membranes (PIMs), such as 2-nitrophenyl octyl ether (NPOE), phthalates, adipates, and sebacates on the mechanical, thermal, and transport properties of membranes. Additionally, butyl stearate (BTS), chosen for its non-toxic nature compared to phthalates and its cost-effectiveness relative to adipates and sebacates, was evaluated as a plasticizer in PIMs for the first time. All plasticizers were incorporated in PIMs made of either cellulose triacetate (CTA) or poly(vinyl chloride) (PVC) as the base polymers and the task-specific ionic liquid trioctylmethylammonium thiosalicylate (TOMATS) as the carrier. The plasticizers were found to significantly affect the characteristics of membrane hydrophilicity, mechanical flexibility, and thermal stability. Transport experiments using Hg(II) as a model target ion revealed that, for CTA-based PIMs, the plasticizer did not significantly affect transport efficiency. However, for PVC-based PIMs, BTS exhibited better efficiency when compared to NPOE. These findings highlight the potential of BTS as an attractive alternative to currently used plasticizers in PVC-based PIM formulations.

Odour-causing compounds in air samples: gas-liquid partition coefficients and determination using solid-phase microextraction and GC with mass spectrometric detection.

A quantification method based on solid-phase microextraction followed by GC coupled to MS was developed for the determination of gas-liquid partition coefficients and for the air monitoring of a group of odour-causing compounds that had previously been found in wastewater samples including dimethyl disulphide, phenol, indole, skatole, octanal, nonanal, benzothiazole and some terpenes. Using a divinylbenzene/carboxen/polydimethylsiloxane fibre, adsorption kinetics have been studied to define an extraction time that would avoid coating saturation. It was found that for an extraction time of 10 min, external calibration could be performed in the range of 0.4-100 µg/m(3), with detection limits between 0.1 and 20 µg/m(3). Inter-day precision of the developed method was evaluated (n = 5) and RSD values between 12 and 24% were obtained for all compounds. The proposed method has been applied to the analysis of air samples surrounding a wastewater treatment plant in Catalonia (Spain). In all air samples evaluated, dimethyl disulphide, limonene and phenol were detected, and the first two were the compounds that showed the highest partition coefficients.

Development of a method for the monitoring of odor-causing compounds in atmospheres surrounding wastewater treatment plants.

This study describes the development of an analytical method based on active collection in a multisorbent Tenax TA/Carbograph 1TD tube, followed by thermal desorption and GC-MS for the determination of 16 volatile organic compounds in air samples. The analyzed compounds include ozone precursors and odor-causing compounds belonging to different chemical families (sulfur- and nitrogen-containing compounds, aldehydes, and terpenes). Two types of sorbents were tested and desorption conditions (temperature, time, and sampling, and desorption flow) were evaluated. External calibration was carried out using the multisorbent bed. Method detection limits in the range 0.2-2.0 µg m(-3) for 1 L samples were obtained. The method was applied for determining the target compounds in air samples from two different wastewater treatment plants. Most compounds were detected and toluene, limonene, and nonanal were found in particularly high concentrations with maximum values of 438, 233, and 382 µg m(-3), respectively.

Multiwalled Carbon Nanotubes Embedded in a Polymeric Matrix as a New Material for Thin Film Microextraction (TFME) in Organic Pollutant Monitoring.

It is essential to monitor organic pollutants to control contamination levels in environmental water bodies. In this respect, the development of new materials based on functionalised polymeric films for the measurement of toxic compounds is of interest. In this study, we prepare new films based on polymer cellulose triacetate modified with multi-walled carbon nanotubes for the monitoring of selected compounds: a fungicide (chlorpyrifos) and two emerging contaminants, the musk tonalide and the bactericide triclosan, which are used in the formulation of personal care products. The films, upon contact with water samples and following the principles of thin film microextraction, allow the determination of organic pollutants at low concentration levels. The contact time of the film with a predetermined volume of water is fixed at 60 min, and the compounds are eluted with a small volume (1 mL) of organic solvent for GC-MS analysis. Parameters such as repeatability for different films and detection limits are found to be satisfactory. Applying the method to river water demonstrates its suitability and, in the cases of chlorpyrifos and tonalide, the absence of a significant matrix effect.

Determination of elemental bioavailability in soils and sediments by microwave induced plasma optical emission spectrometry (MIP-OES): Matrix effects and calibration strategies.

In the past few years, microwave induced plasma optical emission spectrometry (MIP-OES) has generated great interest as an alternative technique to inductively coupled plasma-based techniques due to its lower operational cost. Since MIP-OES suffers from severe matrix effects due to easily ionizable elements (EIEs) (Na, Ca, etc.), it is unclear whether this technique could be employed for elemental bioavailability studies in soils and sediments since the main extractant solutions employed in such works may contain high levels of these elements. Thus, the aim of this work was to evaluate the feasibility of MIP-OES as a detector for such applications. To this end, the influence of different extractant solutions (0.25 mol L-1 MgCl2, 0.25 mol L-1 CaCl2, 0.10 mol L-1 acetic acid, 0.05 mol L-1 Na2EDTA, 0.25 mol L-1 NaNO3, 0.25 mol L-1 NaOAc/HOAc and 0.10 mol L-1 NH2OH·HCl) on the analyte emission of several elements (As, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, Rh, Se, Sr and Zn) was investigated. Results were compared to those obtained using a reference solution made of 5% w w-1 HNO3 solution. For saline extractant solutions, both the optimum nebulizer gas flow rate (Qg) and analyte emission were modified with regard to the reference solution. In general, the optimum Qg was reduced by between 0.1 and 0.2 L min-1 for both ionic and atomic lines. Under optimum Qg conditions, analyte emission was supressed by saline solutions except for atomic lines with an upper electronic state below 4 eV, which were enhanced. The magnitude of matrix effects was strongly dependent on EIE ionization energy. The lower the ionization energy, the greater the matrix effects were registered. No measurable matrix effects were registered on both Qg and analyte emission within experimental uncertainties for NH2OH·HCl and acetic acid extractant solutions. Experimental data suggest that matrix effects were related to changes in plasma characteristics and the analyte excitation/ionization mechanism. To mitigate matrix effects and improve long-term MIP-OES performance, internal standardization using either Rh (343.489 nm and 369.236 nm) or OH molecular emission band (308.958 nm) was required. This calibration methodology was successfully applied to the study of the elemental bioavailability in soil samples from a vineyard affected by copper-based fungicides and sediment samples from an area affected by mining waste.

New Insights on the Effects of Water on Polymer Inclusion Membranes Containing Aliquat 336 Derivatives as Carriers.

Surface characterization of polymer inclusion membranes (PIMs) using the polymers cellulose triacetate and polyvinyl chloride, containing different ionic liquids (ILs) as carriers, has been performed. Three different ILs have been tested: commercial trioctyl methylammonium chloride (Aliquat 336-AlqCl-) and two derivatives bearing the counter anion NO3- or SCN- (AlqNO3 and AlqSCN, respectively). Surface analysis was performed by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) for both dry membranes and PIMs immersed for 4 days in ultrapure water to investigate the effect of the interaction of water with the membrane's morphology and composition. XPS analysis of the PIMs revealed that immersion in ultrapure water causes a decrease in the atomic concentration percentage (A.C.%) of the specific IL atoms (Cl, S, and N) when compared with dry samples. Moreover, SEM images of the PIMs containing the IL AlqNO3 showed an alteration in the morphology of the membrane due to water contact at surface level, whereas no changes were observed at a bulk level. These changes in the surface composition of the water equilibrated PIMs may be associated with the solubilization of the IL in the water solution, which, therefore, may affect the reactivity of the membrane's surface. To better understand this effect, PIMs containing both AlqCl and AlqNO3 as carriers were used for arsenic (V) transport. It was found that AlqCl was the most effective IL and that the effectivity of the PIM on As(V) removal was not affected after five cycles of the membrane's reuse.

Effective concentration signature of Zn in a natural water derived from various speciation techniques.

The uptake of nutrients or toxicants by different organisms in aquatic systems is known to correlate with different fractions of the nutrient's or toxicant's total concentration. These fractions can be provided by different analytical techniques, from which the better correlation is expected to be found for those with a characteristic length comparable to that in the considered organism uptake. An effective concentration signature can be built up with the concentration values associated to the availability (i.e. fluxes in dynamic techniques) of the nutrient or toxicant measured by various analytical techniques with different characteristic lengths. Here, this new representation was obtained for the pool of Zn complexes in the Mediterranean stream Riera d'Osor (Girona, Catalonia, Spain) with a suite of four analytical techniques. Absence of Gradients and Nernstian Equilibrium Stripping (AGNES) and Polymer Inclusion Membrane (PIM) devices provided the free Zn concentration. Linear Anodic Stripping Voltammetry provided a labile fraction (defined here as cLASV, higher than the free concentration), related to the diffusion layer scale. Diffusion Gradients in Thin-films provided higher labile fractions (known as DGT concentrations, cDGT) connected to the different characteristic lengths of different configurations (e.g. one or two resin discs) longer, in any case, than that corresponding to LASV. The combination of the information retrieved by the techniques allowed to quantify lability degrees of the pool of Zn complexes and to build up the effective concentration signature for this water.

Needle microextraction trap for on-site analysis of airborne volatile compounds at ultra-trace levels in gaseous samples.

Different capillary needle trap (NT) configurations are studied and compared to evaluate the suitability of this methodology for screening in the analysis of volatile organic compounds (VOCs) in air samples at ultra-trace levels. Totally, 22 gauge needles with side holes give the best performance and results, resulting in good sampling flow reproducibility as well as fast and complete NT conditioning and cleaning. Two different types of sorbent are evaluated: a graphitized carbon (Carbopack X) and a polymeric sorbent (Tenax TA). Optimized experimental conditions were desorption in the GC injector at 300°C, no make-up gas to help the transport of the desorbed compounds to the GC column, 1 min splitless time for injection/desorption, and leaving the NT in the hot injector for about 20 min. Cross-contamination is avoided when samples containing high VOC levels (above likely breakthrough values) are evaluated. Neither carryover nor contamination is detected for storage times up to 48 h at 4°C. The method developed is applied for the analysis of indoor air, outdoor air and breath samples. The results obtained are equivalent to those obtained with other thermal desorption devices but have the advantage of using small sample volumes, being simpler, more economical and more robust than conventional methodologies used for VOC analysis in air samples.

Multivariate analysis of volatile compounds detected by headspace solid-phase microextraction/gas chromatography: A tool for sensory classification of cork stoppers.

The volatile fraction of aqueous cork macerates of tainted and non-tainted agglomerate cork stoppers was analysed by headspace solid-phase microextraction (HS-SPME)/gas chromatography. Twenty compounds containing terpenoids, aliphatic alcohols, lignin-related compounds and others were selected and analysed in individual corks. Cork stoppers were previously classified in six different classes according to sensory descriptions including, 2,4,6-trichloroanisole taint and other frequent, non-characteristic odours found in cork. A multivariate analysis of the chromatographic data of 20 selected chemical compounds using linear discriminant analysis models helped in the differentiation of the a priori made groups. The discriminant model selected five compounds as the best combination. Selected compounds appear in the model in the following order; 2,4,6 TCA, fenchyl alcohol, 1-octen-3-ol, benzyl alcohol and benzothiazole. Unfortunately, not all six a priori differentiated sensory classes were clearly discriminated in the model, probably indicating that no measurable differences exist in the chromatographic data for some categories. The predictive analyses of a refined model in which two sensory classes were fused together resulted in a good classification. Prediction rates of control (non-tainted), TCA, musty-earthy-vegetative, vegetative and chemical descriptions were 100%, 100%, 85%, 67.3% and 100%, respectively, when the modified model was used. The multivariate analysis of chromatographic data will help in the classification of stoppers and provide a perfect complement to sensory analyses.

Preparation and Characterization of Nanoparticle-Doped Polymer Inclusion Membranes. Application to the Removal of Arsenate and Phosphate from Waters.

Nanoparticle-doped polymer inclusion membranes (NP-PIMs) have been prepared and characterized as new materials for the removal of arsenate and phosphate from waters. PIMs are made of a polymer, cellulose triacetate (CTA), and an extractant, which interacts with the compound of interest. We have used the ionic liquid (IL) trioctylmethylammonium chloride (Aliquat 336) as the extractant and have investigated how the addition of nanoparticles can modify membrane properties. To this end, inorganic nanoparticles, such as ferrite (Fe3O4), SiO2 and TiO2, and multiwalled carbon nanotubes (MWCNTs), were blended with the polymer/extractant mixture. Scanning electron microscopy (SEM), infrared spectroscopy (FT-IR), and contact angle measurements have been used to characterize the material. Moreover, PIM stability was checked by measuring the mass loss during the experiments. Since Aliquat 336 acts as an anion exchanger, the NP-PIMs have been explored in two different applications: (i) as sorbent materials for the extraction of arsenate and phosphate anions; (ii) as an organic phase for the separation of arsenate and phosphate in a three-phase system. The presence of oleate-coated ferrite NP in the PIM formulation represents an improvement in the efficiency of NP-PIMs used as sorbents; nevertheless, a decrease in the transport efficiency for arsenate but not for phosphate was obtained. The ease with which the NP-PIMs are prepared suggests good potential for future applications in the treatment of polluted water. Future work will address three main aspects: firstly, the implementation of the Fe3O4-PIMs for the removal of As(V) in real water containing complex matrices; secondly, the study of phosphate recovery with other cell designs that allow large volumes of contaminated water to be treated; and thirdly, the investigation of the role of MWCNTs in PIM stability.

Assessment of environmental tobacco smoke contamination in public premises: significance of 2,5-dimethylfuran as an effective marker.

Contamination by environmental tobacco smoke (ETS) on premises where smoking is permitted is evaluated. Although all target VOCs evaluated show significant differences between smoking and nonsmoking indoors, the results obtained indicate that 2,5-dimethylfuran is the most appropriate and effective marker of ETS contamination given that this compound is only detected in environments where people have smoked and so the detection of this compound cannot be attributed to other contamination sources such as traffic. Moreover, the air levels of this compound due to coffee aroma are below the detection limits for this methodology. A preliminary study is performed to evaluate whether 2,5-dimethylfuran, a smoking breath biomarker, can be detected in passive smokers working in smoking environments. The compound was continuously detected in the breath of nonsmoking employees after being in direct contact with ETS for just a few hours. The Tedlar gas sampling bags had 5% loss of 2,5-dimethylfuran after 3 h of storage, which we took as the maximum recommended period for air sample storage.

Sorbent-packed needle microextraction trap for benzene, toluene, ethylbenzene, and xylenes determination in aqueous samples.

A needle trap (NT) device filled with Carbopack X as a sorbent material is evaluated for the static headspace analysis of benzene, toluene, ethylbenzene, and xylene (BTEX) compounds in aqueous samples. Injection parameters used with the NT device (e.g. volume of carrier gas and time to open the split valve) are evaluated to determine the mechanism involved during the desorption and transferring of the target compounds into the GC column. Furthermore, different parameters affecting the adsorption capacity of the sorbent are studied (e.g. sampling time and temperature, headspace/sample volume ratio, salting-out, and stirring). The evaluation of the method with aqueous samples shows that repeatability and recoveries with the NT device are equivalent to those obtained using solid-phase microextraction with a carboxen/PDMS (CAR/PDMS) coating. LODs obtained with flame ionization detection are in the range of 10-25 µg/L, and in the range of hundredths of µg/L with MS detection. The method developed is satisfactorily applied to the analysis of aqueous samples obtained from wastewater treatment plants.

Investigation of Volatiles in Cork Samples Using Chromatographic Data and the Superposing Significant Interaction Rules (SSIR) Chemometric Tool.

This study describes a new chemometric tool for the identification of relevant volatile compounds in cork by untargeted headspace solid phase microextraction and gas chromatography mass spectrometry (HS-SPME/GC-MS) analysis. The production process in cork industries commonly includes a washing procedure based on water and temperature cycles in order to reduce off-flavors and decrease the amount of trichloroanisole (TCA) in cork samples. The treatment has been demonstrated to be effective for the designed purpose, but chemical changes in the volatile fraction of the cork sample are produced, which need to be further investigated through the chemometric examination of data obtained from the headspace. Ordinary principal component analysis (PCA) based on the numerical description provided by the chromatographic area of several target compounds was inconclusive. This led us to consider a new tool, which is presented here for the first time for an application in the chromatographic field. The superposing significant interaction rules (SSIR) method is a variable selector which directly analyses the raw internal data coming from the spectrophotometer software and, combined with PCA and discriminant analysis, has been able to separate a group of 56 cork samples into two groups: treated and non-treated. This procedure revealed the presence of two compounds, furfural and 5-methylfurfural, which are increased in the case of treated samples. These compounds explain the sweet notes found in the sensory evaluation of the treated corks. The model that is obtained is robust; the overall sensitivity and specificity are 96% and 100%, respectively. Furthermore, a leave-one-out cross-validation calculation revealed that all of the samples can be correctly classified one at a time if three or more PCA descriptors are considered.

Silencing against the conserved NAC domain of the potato StNAC103 reveals new NAC candidates to repress the suberin associated waxes in phellem.

Both suberin and its associated waxes contribute to the formation of apoplastic barriers that protect plants from the environment. Some transcription factors have emerged as regulators of the suberization process. The potato StNAC103 gene was reported as a repressor of suberin polyester and suberin-associated waxes deposition because its RNAi-mediated downregulation (StNAC103-RNAi) over-accumulated suberin and associated waxes in the tuber phellem concomitantly with the induction of representative biosynthetic genes. Here, to explore if other genes of the large NAC gene family participate to this repressive function, we extended the silencing to other NAC members by targeting the conserved NAC domain of StNAC103 (StNAC103-RNAi-c). Transcript profile of the StNAC103-RNAi-c phellem indicated that StNAC101 gene was an additional potential target. In comparison with StNAC103-RNAi, the silencing with StNAC103-RNAi-c construct resulted in a similar effect in suberin but yielded an increased load of associated waxes in tuber phellem, mainly alkanes and feruloyl esters. Globally, the chemical effects in both silenced lines are supported by the transcript accumulation profile of genes involved in the biosynthesis, transport and regulation of apoplastic lipids. In contrast, the genes of polyamine biosynthesis were downregulated. Altogether these results point out to StNAC101 as a candidate to repress the suberin-associated waxes.

Molecular fingerprinting by PCR-denaturing gradient gel electrophoresis reveals differences in the levels of microbial diversity for musty-earthy tainted corks.

The microbial community structure of cork with marked musty-earthy aromas was analyzed using denaturing gradient gel electrophoresis of amplified ribosomal DNA. Cork stoppers and discs were used for DNA extraction and were analyzed by using selective primers for bacteria and fungi. Stoppers clearly differed from discs harboring a different fungal community. Moreover, musty-earthy samples of both types were shown to have a specific microbiota. The fungi Penicillium glabrum and Neurospora spp. were present in all samples and were assumed to make only a small contribution to off-odor development. In contrast, Penicillium islandicum and Penicillium variabile were found almost exclusively in 2,4,6-trichloroanisole (TCA) tainted discs. Conversely, Rhodotorula minuta and Rhodotorula sloofiae were most common in cork stoppers, where only small amounts of TCA were detected. Alpha- and gammaproteobacteria were the most commonly found bacteria in either control or tainted cork stoppers. Specific Pseudomonas and Actinobacteria were detected in stoppers with low amounts of TCA and 2-methoxy-3,5-dimethylpyrazine. These results are discussed in terms of biological degradation of taint compounds by specific microorganisms. Reliable and straightforward microbial identification methods based on a molecular approach provided useful data to determine and evaluate the risk of taint formation in cork.

Chloroanisoles and Other Chlorinated Compounds in Cork from Different Geographical Areas.

Cork quality is crucial for the fabrication of corks intended to be used to seal wine bottles. This work has focused on the determination of chloroanisoles (CAs)-exogenous compounds with a low perception threshold-in cork. The identification and quantification of these compounds was carried out with Bond Elut-ENV solid phase extraction and gas chromatography with mass spectrometry detection. Cork samples were obtained from oaks from Catalonia, Extremadura and Italy, and the presence of CAs was evaluated. Moreover, cork affected by the presence of yellow stains (a defect present in cork, mainly originated from the growth of the fungus Armillaria mellea) was analysed separately. The results obtained from cork macerates revealed the presence of trichloroanisole (TCA) in Catalan and Italian cork. Furthermore, TCA concentration was not statistically different when comparing cork affected and non-affected by the growth of A. mellea. Other chlorinated compounds were identified by comparison of their mass spectra with the data from the NIST library.