Polyaniline Modified CNTs and Graphene Nanocomposite for Removal of Lead and Zinc Metal Ions: Kinetics, Thermodynamics and Desorption Studies.

A novel polyaniline-modified CNT and graphene-based nanocomposite (2.32-7.34 nm) was prepared and characterized by spectroscopic methods. The specific surface area was 176 m2/g with 0.232 cm3/g as the specific pore volume. The nanocomposite was used to remove zinc and lead metal ions from water; showing a high removal capacity of 346 and 581 mg/g at pH 6.5. The data followed pseudo-second-order, intraparticle diffusion and Elovich models. Besides this, the experimental values obeyed Langmuir and Temkin isotherms. The results confirmed that the removal of lead and zinc ions occurred in a mixed mode, that is, diffusion absorption and ion exchange between the heterogeneous surface of the sorbent containing active adsorption centers and the solution containing metal ions. The enthalpy values were 149.9 and 158.6 J.mol-1K-1 for zinc and lead metal ions. The negative values of free energies were in the range of -4.97 to -26.3 kJ/mol. These values indicated an endothermic spontaneous removal of metal ions from water. The reported method is useful to remove the zinc and lead metal ions in any water body due to the high removal capacity of nanocomposite at natural pH of 6.5. Moreover, a low dose of 0.005 g per 30 mL made this method economical. Furthermore, a low contact time of 15 min made this method applicable to the removal of the reported metal ions from water in a short time. Briefly, the reported method is highly economical, nature-friendly and fast and can be used to remove the reported metal ions from any water resource.

Engendering High Energy Density LiFePO4 Electrodes with Morphological and Compositional Tuning.

Improving the energy density of Li-ion batteries is critical to meet the requirements of electric vehicles and energy storage systems. In this work, LiFePO4 active material was combined with single-walled carbon nanotubes as the conductive additive to develop high-energy-density cathodes for rechargeable Li-ion batteries. The effect of the morphology of the active material particles on the cathodes' electrochemical characteristics was investigated. Although providing higher packing density of electrodes, spherical LiFePO4 microparticles had poorer contact with an aluminum current collector and showed lower rate capability than plate-shaped LiFePO4 nanoparticles. A carbon-coated current collector helped enhance the interfacial contact with spherical LiFePO4 particles and was instrumental in combining high electrode packing density (1.8 g cm-3) with excellent rate capability (100 mAh g-1 at 10C). The weight percentages of carbon nanotubes and polyvinylidene fluoride binder in the electrodes were optimized for electrical conductivity, rate capability, adhesion strength, and cyclic stability. The electrodes that were formulated with 0.25 wt.% of carbon nanotubes and 1.75 wt.% of the binder demonstrated the best overall performance. The optimized electrode composition was used to formulate thick free-standing electrodes with high energy and power densities, achieving the areal capacity of 5.9 mAh cm-2 at 1C rate.

Ionomers Based on Addition and Ring Opening Metathesis Polymerized 5-phenyl-2-norbornene as a Membrane Material for Ionic Actuators.

Two types of poly(5-phenyl-2-norbornene) were synthesized via ring opening metathesis and addition polymerization. The polymers sulfonation reaction under homogeneous conditions resulted in ionomer with high sulfonation degree up to 79% (IEC 3.36 meq/g). The prepared ionomer was characterized by DSC, GPC, 1H NMR and FT-IR. Polymers for electromechanical applications soluble in common polar organic solvents were obtained by replacing proton of sulfonic group with imidazolium and 1-methylimidazlium. Membranes were prepared using the above-mentioned polymers and 1-ethyl-3-methylimidazolium tetrafluoroborate (EMImBF4), as well as mixtures with polyvinylidene fluoride (PVDF). Mechanical, morphological, and conductive properties of the membranes were examined by tensile testing, SEM, and impedance spectroscopy, respectively. Dry and air-stable actuators with electrodes based on SWCNT were fabricated via hot-pressing. Actuators with membranes based on methylimidazolium containing ionomers outperformed classical bucky gel actuator and demonstrated high strain (up to 1.14%) and generated stress (up to 1.21 MPa) under low voltage of 2 V.

The Physicochemical Characterization of New "Green" Epoxy-Resin Hardener Made from PET Waste.

"Green" thermally stable hardener was synthesized from a PET waste. The rigid molecular linear structure of the new hardener suggests that it will provide the polymer matrix with the necessary physical and mechanical characteristics. It also allows the expectation that cured matrix based on this hardener can provide increased toughness. New hardener was used as a curing agent for three epoxy resins-tetraglycidyl methylenedianiline (TGDMA, 111-117 EEW), diglycidylether of bisphenol A (DGEBA, 170-192 EEW) and solid epoxy resin (SER)-with a medium molecular weight (860-930 EEW) based on DGEBA. The mixtures were found to have the highest Tg for the DGEBA resin, and high of that for TGDMA and SER. According to the DMA analysis for two cured matrices, the hardener proved to be no worse than the standard ones, and made it possible to obtain cured matrices with excellent mechanical properties, which allows us to hope for further application of new hardener cured epoxy matrices in appropriate composite materials at high temperatures.

Dynamic and Static Mechanical Properties of Crosslinked Polymer Matrices: Multiscale Simulations and Experiments.

We studied the static and dynamic mechanical properties of crosslinked polymer matrices using multiscale simulations and experiments. We continued to develop the multiscale methodology for generating atomistic polymer networks, and applied it to the case of phthalonitrile resin. The mechanical properties of the resulting networks were analyzed using atomistic molecular dynamics (MD) and dissipative particle dynamics (DPD). The Young's and storage moduli increased with conversion, due both to the appearance of a network of covalent bonds, and to freezing of degrees of freedom and lowering of the glass transition temperature during crosslinking. The simulations' data showed good quantitative agreement with experimental dynamic mechanical analysis measurements at temperatures below the glass transition. The data obtained in MD and DPD simulations at elevated temperatures were conformable. This makes it possible to use the suggested approach for the prediction of mechanical properties of a broad range of polymer matrices, including ones with high structural heterogeneity.