Response Surface Modeling of the Steady-State Impedance Responses of Gas Sensor Arrays Comprising Functionalized Carbon Nanotubes to Detect Ozone and Nitrogen Dioxide.

Carbon nanotube (CNT) sensors provide a versatile chemical platform for ambient monitoring of ozone (O3) and nitrogen dioxide (NO2), two important airborne pollutants known to cause acute respiratory and cardiovascular health problems. CNTs have shown great potential for use as sensing layers due to their unique properties, including high surface to volume ratio, numerous active sites and crystal facets with high surface reactivity, and high thermal and electrical conductivity. With operational advantages such as compactness, low-power operation, and easy integration with electronics devices, nanotechnology is expected to have a significant impact on portable low-cost environmental sensors. Enhanced sensitivity is feasible by functionalizing the CNTs with polymers, metals, and metal oxides. This paper focuses on the design and performance of a two-element array of O3 and NO2 sensors comprising single-walled CNTs functionalized by covalent modification with organic functional groups. Unlike the conventional chemiresistor in which the change in DC resistance across the sensor terminals is measured, we characterize the sensor array response by measuring both the magnitude and phase of the AC impedance. Multivariate response provides higher degrees of freedom in sensor array data processing. The complex impedance of each sensor is measured at 5 kHz in a controlled gas-flow chamber using gas mixtures with O3 in the 60-120 ppb range and NO2 between 20 and 80 ppb. The measured data reveal response change in the 26-36% range for the O3 sensor and 5-31% for the NO2 sensor. Multivariate optimization is used to fit the laboratory measurements to a response surface mathematical model, from which sensitivity and selectivity are calculated. The ozone sensor exhibits high sensitivity (e.g., 5 to 6 MΩ/ppb for the impedance magnitude) and high selectivity (0.8 to 0.9) for interferent (NO2) levels below 30 ppb. However, the NO2 sensor is not selective.

Sublimation-assisted graphene transfer technique based on small polyaromatic hydrocarbons.

Advances in the chemical vapor deposition (CVD) growth of graphene have made this material a very attractive candidate for a number of applications including transparent conductors, electronics, optoeletronics, biomedical devices and energy storage. The CVD method requires transfer of graphene on a desired substrate and this is most commonly accomplished with polymers. The removal of polymer carriers is achieved with organic solvents or thermal treatment which makes this approach inappropriate for application to plastic thin films such as polyethylene terephthalate substrates. An ultraclean graphene transfer method under mild conditions is highly desired. In this article, we report a naphthalene-assisted graphene transfer technique which provides a reliable route to residue-free transfer of graphene to both hard and flexible substrates. The quality of the transferred graphene was characterized with atomic force microscopy, scanning electron microscopy, and Raman spectroscopy. Field effect transistors, based on the naphthalene-transfered graphene, were fabricated and characterized. This work has the potential to broaden the applications of CVD graphene in fields where ultraclean graphene and mild graphene transfer conditions are required.

Fast Electrochromic Device Based on Single-Walled Carbon Nanotube Thin Films.

Optical properties of electrochromic materials can be controlled by the application of an electric field allowing recent development of new applications such as smart windows technology for indoor climate control and energy conservation. We report the fabrication of a single-walled nanotube (SWNT) thin film based electro-optical modulator controlled by ionic liquid polarization in which the active electrochromic layer is made of a film of semiconducting (SC-) SWNTs and the counter-electrode is composed of a film of metallic (MT-) SWNTs. Optimization of this electro-optical cell allows the operations with an optical modulation depth of 3.7 dB and a response time in the millisecond range, which is thousands of times faster than typical electrolyte-controlled devices. In addition, a dual electro-optical device was built utilizing electro-optically active SC-SWNT films for each electrode that allowed increasing modulation depth of 6.7 dB while preserving the speed of the response.

Giant Raman Response to the Encapsulation of Sulfur in Narrow Diameter Single-Walled Carbon Nanotubes.

Encapsulation of sulfur in HiPCO-SWNTs leads to large changes in the Raman spectra with the appearance of new peaks at 319, 395, and 715 cm(-1) which originate from the sulfur species within the SWNTs, while the high frequency SWNT bands (ν > 1200 cm(-1)) are decreased in intensity. The encapsulated species also shifts the near-IR interband electronic transitions to lower energy by more than 10%. These effects seem to originate with the van der Waals interaction of the confined sulfur species with the walls of the SWNTs which are not expected to be significant in the case of the previously studied large diameter SWNTs. We suggest that sulfur in the small diameter SWNTs exists as a helical polymeric sulfur chain that enters the SWNT interior in the form of S2 ((3)Σ(g)(-)) molecules which undergo polymerization to linear diradicals.

Networks of semiconducting SWNTs: contribution of midgap electronic states to the electrical transport.

Single-walled carbon nanotube (SWNT) thin films provide a unique platform for the development of electronic and photonic devices because they combine the advantages of the outstanding physical properties of individual SWNTs with the capabilities of large area thin film manufacturing and patterning technologies. Flexible SWNT thin film based field-effect transistors, sensors, detectors, photovoltaic cells, and light emitting diodes have been already demonstrated, and SWNT thin film transparent, conductive coatings for large area displays and smart windows are under development. While chirally pure SWNTs are not yet commercially available, the marketing of semiconducting (SC) and metallic (MT) SWNTs has facilitated progress toward applications by making available materials of consistent electronic structure. Nevertheless the electrical transport properties of networks of separated SWNTs are inferior to those of individual SWNTs. In particular, for semiconducting SWNTs, which are the subject of this Account, the electrical transport drastically differs from the behavior of traditional semiconductors: for example, the bandgap of germanium (E = 0.66 eV) roughly matches that of individual SC-SWNTs of diameter 1.5 nm, but in the range 300-100 K, the intrinsic carrier concentration in Ge decreases by more than 10 orders of magnitude while the conductivity of a typical SC-SWNT network decreases by less than a factor of 4. Clearly this weak modulation of the conductivity hinders the application of SC-SWNT films as field effect transistors and photodetectors, and it is the purpose of this Account to analyze the mechanism of the electrical transport leading to the unusually weak temperature dependence of the electrical conductivity of such networks. Extrinsic factors such as the contribution of residual amounts of MT-SWNTs arising from incomplete separation and doping of SWNTs are evaluated. However, the observed temperature dependence of the conductivity indicates the presence of midgap electronic states in the semiconducting SWNTs, which provide a source of low-energy excitations, which can contribute to hopping conductance along the nanotubes following fluctuation induced tunneling across the internanotube junctions, which together dominate the low temperature transport and limit the resistivity of the films. At high temperatures, the intrinsic carriers thermally activated across the bandgap as in a traditional semiconductor became available for band transport. The midgap states pin the Fermi level to the middle of the bandgap, and their origin is ascribed to defects in the SWNT walls. The presence of such midgap states has been reported in connection with scanning tunneling spectroscopy experiments, Coulomb blockade observations in low temperature electrical measurements, selective electrochemical deposition imaging, tip-enhanced Raman spectroscopy, high resolution photocurrent spectroscopy, and the modeling of the electronic density of states associated with various defects. Midgap states are present in conventional semiconductors, but what is unusual in the present context is the extent of their contribution to the electrical transport in networks of semiconducting SWNTs. In this Account, we sharpen the focus on the midgap states in SC-SWNTs, their effect on the electronic properties of SC-SWNT networks, and the importance of these effects on efforts to develop electronic and photonic applications of SC-SWNTs.

Chemically functionalized single-walled carbon nanotubes enhance the glutamate uptake characteristics of mouse cortical astrocytes.

Using a radioactive glutamate uptake assay and immunolabeling, we report that single-walled carbon nanotubes, chemically functionalized with polyethylene glycol (SWCNT-PEG), delivered as a colloidal solute, cause an increase in the uptake of extracellular glutamate by astrocytes and an increase in the immunoreactivity of the glutamate transporter GLAST on their cell surface, which is likely a consequence of an increase in the immunoreactivity of glial fibrillary acidic protein. Additional corollary is that astrocytes exposed to SWCNT-PEG became larger and stellate, morphological characteristics of maturation and heightened activity of these glial cells. These results imply that SWCNT-PEG could potentially be used as a viable candidate for neural prosthesis applications, perhaps to alleviate the death toll of neurons due to glutamate excitotoxicity, a pathological process observed in brain and spinal cord injuries.

Changes in the morphology and proliferation of astrocytes induced by two modalities of chemically functionalized single-walled carbon nanotubes are differentially mediated by glial fibrillary acidic protein.

Alterations in glial fibrillary acidic protein (GFAP) levels accompany the changes in the morphology and proliferation of astrocytes induced by colloidal solutes and films of carbon nanotubes (CNTs). To determine if GFAP is required for the effects of CNTs on astrocytes, we used astrocytes isolated from GFAP null mice. We find that selected astrocytic changes induced by CNTs are mediated by GFAP, i.e., perimeter, shape, and cell death for solutes, and proliferation for films.

Effect of atomic interconnects on percolation in single-walled carbon nanotube thin film networks.

The formation of covalent bonds to single-walled carbon nanotube (SWNT) or graphene surfaces usually leads to a decrease in the electrical conductivity and mobility as a result of the structural rehybridization of the functionalized carbon atoms from sp(2) to sp(3). In the present study, we explore the effect of metal deposition on semiconducting (SC-) and metallic (MT-) SWNT thin films in the vicinity of the percolation threshold and we are able to clearly delineate the effects of weak physisorption, ionic chemisorption with charge transfer, and covalent hexahapto (η(6)) chemisorption on these percolating networks. The results support the idea that for those metals capable of forming bis-hexahapto-bonds, the generation of covalent (η(6)-SWNT)M(η(6)-SWNT) interconnects provides a conducting pathway in the SWNT films and establishes the transition metal bis-hexahapto organometallic bond as an electronically conjugating linkage between graphene surfaces.

Effect of covalent chemistry on the electronic structure and properties of carbon nanotubes and graphene.

In this Account, we discuss the chemistry of graphitic materials with particular reference to three reactions studied by our research group: (1) aryl radical addition, from diazonium precursors, (2) Diels-Alder pericyclic reactions, and (3) organometallic complexation with transition metals. We provide a unified treatment of these reactions in terms of the degenerate valence and conduction bands of graphene at the Dirac point and the relationship of their orbital coefficients to the HOMO and LUMO of benzene and to the Clar structures of graphene. In the case of the aryl radical addition and the Diels-Alder reactions, there is full rehybridization of the derivatized carbon atoms in graphene from sp(2) to sp(3), which removes these carbon atoms from conjugation and from the electronic band structure of graphene (referred to as destructive rehybridization). The radical addition process requires an electron transfer step followed by the formation of a σ-bond and the creation of a π-radical in the graphene lattice, and thus, there is the potential for unequal degrees of functionalization in the A and B sublattices and the possibility of ferromagnetism and superparamagnetism in the reaction products. With regard to metal functionalization, we distinguish four limiting cases: (a) weak physisorption, (b) ionic chemisorption, in which there is charge transfer to the graphitic structure and preservation of the conjugation and band structure, (c) covalent chemisorption, in which there is strong rehybridization of the graphitic band structure, and (d) covalent chemisorption with formation of an organometallic hexahapto-metal bond that largely preserves the graphitic band structure (constructive rehybridization). The constructive rehybridization that accompanies the formation of bis-hexahapto-metal bonds, such as those in (η(6)-SWNT)Cr(η(6)-SWNT), interconnects adjacent graphitic surfaces and significantly reduces the internanotube junction resistance in single-walled carbon nanotube (SWNT) networks. The conversion of sp(2) hybridized carbon atoms to sp(3) can introduce a band gap into graphene, influence the electronic scattering, and create dielectric regions in a graphene wafer. However, the organometallic hexahapto (η(6)) functionalization of the two-dimensional (2D) graphene π-surface with transition metals provides a new way to modify graphitic structures that does not saturate the functionalized carbon atoms and, by preserving their structural integrity, maintains the delocalization in these extended periodic π-electron systems and offers the possibility of three-dimensional (3D) interconnections between adjacent graphene sheets. These structures may find applications in interconnects, 3D-electronics, organometallic catalysis, atomic spintronics and in the fabrication of new electronic materials.

Chemically functionalized single-walled carbon nanotube films modulate the morpho-functional and proliferative characteristics of astrocytes.

We used single-walled carbon nanotube (CNT) films to modulate the morpho-functional and proliferative characteristics of astrocytes. When plated on the CNT films of various thicknesses, astrocytes grow bigger and rounder in shape with a decrease in the immunoreactivity of glial fibrillary acidic protein along with an increase in their proliferation, changes associated with the dedifferentiation of astrocytes in culture. Thus, CNT films, as a coating material for electrodes used in brain machine interface, could reduce astrogliosis around the site of implantation.

Chemically Functionalized Single-Walled Carbon Nanotubes Prevent the Reduction in Plasmalemmal Glutamate Transporter EAAT1 Expression in, and Increase the Release of Selected Cytokines from, Stretch-Injured Astrocytes in Vitro.

We tested the effects of water-soluble single-walled carbon nanotubes, chemically functionalized with polyethylene glycol (SWCNT-PEG), on primary mouse astrocytes exposed to a severe in vitro simulated traumatic brain injury (TBI). The application of SWCNT-PEG in the culture media of injured astrocytes did not affect cell damage levels, when compared to those obtained from injured, functionalization agent (PEG)-treated cells. Furthermore, SWCNT-PEG did not change the levels of oxidatively damaged proteins in astrocytes. However, this nanomaterial prevented the reduction in plasmalemmal glutamate transporter EAAT1 expression caused by the injury, rendering the level of EAAT1 on par with that of control, uninjured PEG-treated astrocytes; in parallel, there was no significant change in the levels of GFAP. Additionally, SWCNT-PEG increased the release of selected cytokines that are generally considered to be involved in recovery processes following injuries. As a loss of EAATs has been implicated as a culprit in the suffering of human patients from TBI, the application of SWCNT-PEG could have valuable effects at the injury site, by preventing the loss of astrocytic EAAT1 and consequently allowing for a much-needed uptake of glutamate from the extracellular space, the accumulation of which leads to unwanted excitotoxicity. Additional potential therapeutic benefits could be reaped from the fact that SWCNT-PEG stimulated the release of selected cytokines from injured astrocytes, which would promote recovery after injury and thus counteract the excess of proinflammatory cytokines present in TBI.

Chemistry at the Dirac point: Diels-Alder reactivity of graphene.

Most of the interesting physics of graphene results from the singular electronic band structure at the so-called Dirac point, where the conduction and valence bands cross in momentum space. Although graphene is very stable thermodynamically, the electronic structure at the Dirac point facilitates basal plane chemistry including pericyclic reactions such as the Diels-Alder reaction. We have discovered a series of facile Diels-Alder reactions in which graphene can function either as a diene when paired with tetracyanoethylene and maleic anhydride or as a dienophile when paired with 2,3-dimethoxybutadiene and 9-methylanthracene. In this Account, we seek to rationalize these findings using simple arguments based on considerations of orbital symmetry and the frontier molecular orbital theory. The graphene conduction and valence bands (HOMO and LUMO) cross at the Dirac point, which defines the work function (W = 4.6 eV). Thus, the HOMO and LUMO form a degenerate pair of orbitals at this point in momentum space with the same ionization potential (IP) and electron affinity (EA). Based on the importance of the energies of the HOMO (-IP) and LUMO (-EA) in frontier molecular orbital (FMO) theory, graphene should be a reactive partner in Diels-Alder reactions due to the very high-lying HOMO and low-lying LUMO (energies of -4.6 eV). Inspection of the orbital symmetries of the degenerate pair of half-occupied band orbitals at the Dirac point confirms that with the appropriate orbital occupancies, both diene and dienophile reaction partners should undergo concerted Diels-Alder reactions with graphene that are allowed based on the Woodward-Hoffmann principles of orbital symmetry.

Chemically functionalized water-soluble single-walled carbon nanotubes modulate morpho-functional characteristics of astrocytes.

We report the use of chemically functionalized water-soluble single-walled carbon nanotubes (ws-SWCNTs) for the modulation of morpho-functional characteristics of astrocytes. When added to the culturing medium, ws-SWCNTs were able to make astrocytes larger and stellate/mature, changes associated with the increase in glial fibrillary acidic protein immunoreactivity. Thus, ws-SWCNTs could have more beneficial effects at the injury site than previously thought; by affecting astrocytes, they could provide for a more comprehensive re-establishment of the brain computational power.

Impact of 1,8-Diiodooctane (DIO) Additive on the Active Layer Properties of Cu2ZnSnS4 Kesterite Thin Films Prepared by Electrochemical Deposition for Photovoltaic Applications.

Kesterite Cu2ZnSnS4 (CZTS) thin films using various 1,8-diiodooctane (DIO) polymer additive concentrations were fabricated by the electrochemical deposition method. The optical, electrical, morphological, and structural properties of the CZTS thin films synthesized using different concentrations of 5 mg/mL, 10 mg/mL, 15 mg/mL, and 20 mg/mL were investigated using different techniques. Cyclic voltammetry exhibited three cathodic peaks at -0.15 V, -0.54 V, and -0.73 V, corresponding to the reduction of Cu2+, Sn2+, Sn2+, and Zn2+ metal ions, respectively. The analysis of the X-ray diffraction (XRD) pattern indicated the formation of the pure kesterite crystal structure, and the Raman spectra showed pure CZTS with the A1 mode of vibration. Field emission scanning electron microscopy (FE-SEM) indicated that the films are well grown, with compact, crack-free, and uniform deposition and a grain size of approximately 4 µm. For sample DIO-20 mg/mL, the elemental composition of the CZTS thin film was modified to Cu:Zn:Sn: and S = 24.2:13.3:12.3:50.2, which indicates a zinc-rich and copper-poor composition. The X-ray photoelectron spectroscopy (XPS) results confirmed the existence of Cu, Sn, Zn, and S elements and revealed the element oxidation states. The electrochemical deposition synthesis increased the absorption of the CZTS film to more than 104 cm-1 with a band gap between 1.62 eV and 1.51 eV. Finally, the photovoltaic properties of glass/CZTS/CdS/n-ZnO/aluminum-doped zinc oxide (AZO)/Ag solar cells were investigated. The best-performing photovoltaic device, with a DIO concentration of 20 mg/mL, had a short-circuit current density of 16.44 mA/cm2, an open-circuit voltage of 0.465 V, and a fill factor of 64.3%, providing a conversion efficiency of 4.82%.

Doping with Niobium Nanoparticles as an Approach to Increase the Power Conversion Efficiency of P3HT:PCBM Polymer Solar Cells.

Metal additive processing in polymer: fullerene bulk heterojunction systems is recognized as a viable way for improving polymer photovoltage performance. In this study, the effect of niobium (Nb) metal nanoparticles at concentrations of 2, 4, 6, and 8 mg/mL on poly(3-hexylthiophene-2,5-diyl) (P3HT)-6,6]-phenyl C61-butyric acid methyl ester (PCBM) blends was analyzed. The effect of Nb volume concentration on polymer crystallinity, optical properties, and surface structure of P3HT and PCBM, as well as the enhancement of the performance of P3HT:PC61BM solar cells, are investigated. Absorption of the P3HT:PC61BM mix is seen to have a high intensity and a red shift at 500 nm. The reduction in PL intensity with increasing Nb doping concentrations indicates an increase in PL quenching, suggesting that the domain size of P3HT or conjugation length increases. With a high Nb concentration, crystallinity, material composition, surface roughness, and phase separation are enhanced. Nb enhances PCBM's solubility in P3HT and decreases the size of amorphous P3HT domains. Based on the J-V characteristics and the optoelectronic study of the thin films, the improvement results from a decreased recombination current, changes in morphology and crystallinity, and an increase in the effective exciton lifespan. At high doping concentrations of Nb nanoparticles, the development of the short-circuit current (JSC) is associated with alterations in the crystalline structure of P3HT. The highest-performing glass/ITO/PEDOT:PSS/P3HT:PCBM:Nb/MoO3/Au structures have short-circuit current densities (JSC) of 16.86 mA/cm2, open-circuit voltages (VOC) of 466 mV, fill factors (FF) of 65.73%, and power conversion efficiency (µ) of 5.16%.

Bioactive hybrid membrane-based cellulose acetate/bioactive glass/hydroxyapatite/carbon nanotubes nanocomposite for dental applications.

The present work aimed to fabricate a set of hybrid bioactive membrane in the form of bio-nanocomposite films for dental applications using the casting dissolution procedures. The formulation of the targeted materials was consisting of cellulose acetate/bioactive glass/hydroxyapatite/carbon nanotubes with a general abbreviation CA-HAP-BG-SWCNTs. The nanocomposites were characterized using XRD, FTIR, SEM-EDX and Raman spectroscopy. XRD, FTIR and SEM characters confirm the nanocomposites formation with good compatibility. The fabricated materials had a semi crystalline structure. The mechanical and thermal properties, as well as contact angle and bioactivity of the fabricated nanocomposites were investigated. The SEM images for showed beehive-like architectures with a thicker frame for the second material. All fabricated materials showed good thermal behaviors. Furthermore, the agar diffusion antimicrobial study showed that the prepared nanocomposites do not exhibit an antibacterial activity against five pathogenic bacterial strains. Additionally, cytotoxicity of a dental nanocomposite filling agent was evaluated. Vero normal cells were incubated with test materials for 72h at 37 °C and 5% CO2. Cell viability was detected using a SRB assay. All nanocomposites were mildly to non-cytotoxic to Vero cells at high concentration in contrast to the inhibitory effect of doxorubicin which was added at 10-fold lower concertation than the nanocomposites. Hence, the proposed nanocomposite is promising candidates for dental applications.

Aryl functionalization as a route to band gap engineering in single layer graphene devices.

Chemical functionalization is a promising route to band gap engineering of graphene. We chemically grafted nitrophenyl groups onto exfoliated single-layer graphene sheets in the form of substrate-supported or free-standing films. Our transport measurements demonstrate that nonsuspended functionalized graphene behaves as a granular metal, with variable range hopping transport and a mobility gap ∼0.1 eV at low temperature. For suspended graphene that allows functionalization on both surfaces, we demonstrate tuning of its electronic properties from a granular metal to a semiconductor in which transport occurs via thermal activation over a transport gap ∼80 meV from 4 to 300 K. This noninvasive and scalable functionalization technique paves the way for CMOS-compatible band gap engineering of graphene electronic devices.

Reversible grafting of α-naphthylmethyl radicals to epitaxial graphene.

The Kolbe electrochemical oxidation strategy has been utilized to achieve an efficient quasireversible electrochemical grafting of the α-naphthylmethyl functional group to graphene. The method facilitates reversible bandgap engineering in graphene and preparation of electrochemically erasable organic dielectric films. The picture shows Raman D-band maps of both systems.

The coordination chemistry of oxide and nanocarbon materials.

Understanding how a ligand affects the steric and electronic properties of a metal is the cornerstone of the inorganic chemistry enterprise. What happens when the ligand is an extended surface? This question is central to the design and implementation of state-of-the-art functional materials containing transition metals. This perspective will describe how these two very different sets of extended surfaces can form well-defined coordination complexes with metals. In the Green formalism, functionalities on oxide surfaces react with inorganics to form species that contain X-type or LX-type interactions between the metal and the oxide. Carbon surfaces are neutral L-type ligands; this perspective focuses on carbons that donate six electrons to a metal. The nature of this interaction depends on the curvature, and thereby orbital overlap, between the metal and the extended π-system from the nanocarbon.

Patterning submicron photomechanical features into single diarylethene crystals using electron beam lithography.

Lithography methods are commonly used to create structures in inorganic semiconductors like silicon but have not been widely applied to organic crystals. In this work, electron beam lithography (EBL) is used to pattern structures into single organic photomechanical crystals composed of 1,2-bis(2-methyl-5-phenyl-3-thienyl)perfluorocyclopentene. The electron beam creates amorphous regions of decomposed molecules, while the reactivity of the unexposed crystal regions is preserved under a removable Au coating. Exposure of the patterned crystal to 365 nm light causes ridges of amorphous material to increase in height by 30-70%. This height increase can be reversed by visible light exposure and undergo multiple cycles. The reversible surface morphology changes are strong enough to rupture a sheet of graphene placed on top of the patterned crystal. Surprisingly, the change in dimensions of the EBL features is an order of magnitude larger than the changes in overall crystal dimensions as deduced from X-ray diffraction experiments and microscopy observations. A dynamic extrusion model is presented to explain how nanoscale features imprinted into single crystals can amplify molecular-level photomechanical changes. This work demonstrates the capability of EBL methods to produce sub-micron structural features on single photomechanical crystals, providing a new route to monolithic light-powered actuator devices.