Stability effects on CO2 adsorption for the DOBDC series of metal-organic frameworks.

Metal-organic frameworks with unsaturated metal centers in their crystal structures, such as Ni/DOBDC and Mg/DOBDC, are promising adsorbents for carbon dioxide capture from flue gas due to their high CO(2) capacities at subatmospheric pressures. However, stability is a critical issue for their application. In this paper, the stabilities of Ni/DOBDC and Mg/DOBDC are investigated. Effects of steam conditioning, simulated flue gas conditioning, and long-term storage on CO(2) adsorption capacities are considered. Results show that Ni/DOBDC can maintain its CO(2) capacity after steam conditioning and long-term storage, whereas Mg/DOBDC does not. Nitrogen isotherms for Mg/DOBDC show a drop in surface area after steaming, corresponding to the decrease in CO(2) adsorption, which may be caused by a reduction of unsaturated metal centers in its structure. Conditioning with dry simulated flue gas at room temperature only slightly affects CO(2) adsorption in Ni/DOBDC. However, introducing water vapor into the simulated flue gas further reduces the CO(2) capacity of Ni/DOBDC.

CO2/H2O adsorption equilibrium and rates on metal-organic frameworks: HKUST-1 and Ni/DOBDC.

Metal-organic frameworks (MOFs) have recently attracted intense research interest because of their permanent porous structures, huge surface areas, and potential applications as novel adsorbents and catalysts. In order to provide a basis for consideration of MOFs for removal of carbon dioxide from gases containing water vapor, such as flue gas, we have studied adsorption equilibrium of CO(2), H(2)O vapor, and their mixtures and also rates of CO(2) adsorption in two MOFs: HKUST-1 (CuBTC) and Ni/DOBDC (CPO-27-Ni or Ni/MOF-74). The MOFs were synthesized via solvothermal methods, and the as-synthesized products were solvent exchanged and regenerated before experiments. Pure component adsorption equilibria and CO(2)/H(2)O binary adsorption equilibria were studied using a volumetric system. The effects of H(2)O adsorption on CO(2) adsorption for both MOF samples were determined, and the results for 5A and NaX zeolites were included for comparison. The hydrothermal stabilities for the two MOFs over the course of repetitive measurements of H(2)O and CO(2)/H(2)O mixture equilibria were also studied. CO(2) adsorption rates from helium for the MOF samples were investigated by using a unique concentration-swing frequency response (CSFR) system. Mass transfer into the MOFs is rapid with the controlling resistance found to be macropore diffusion, and rate parameters were established for the mechanism.

Virtual high throughput screening confirmed experimentally: porous coordination polymer hydration.

Hydrothermal stability is a pertinent issue to address for many industrial applications where percent levels of water can be present at temperatures ranging from subambient to several hundred degrees. Our objective is to understand relative stabilities of MOF materials through experimental testing combined with molecular modeling. This will enable the ultimate design of materials with improved hydrothermal stability, while maintaining the properties of interest. The tools that we have employed for these studies include quantum mechanical calculations based upon cluster models and combinatorial steaming methods whereby a steam stability map was formulated according to the relative stability of different materials. The experimental steaming method allows for high throughput screening of materials stability over a broad range of steam levels as well as in-depth investigation of structural transformations under more highly resolved conditions, while the cluster model presented here yields the correct trends in hydrothermal stability. Good agreement was observed between predicted relative stabilities of materials by molecular modeling and experimental results. Fundamental information from these studies has provided insight into how metal composition and coordination, chemical functionality of organic linker, framework dimensionality, and interpenetration affect the relative stabilities of PCP materials. This work suggests that the strength of the bond between the metal oxide cluster and the bridging linker is important in determining the hydrothermal stability of the PCP. Although the flexibility of the framework plays a role, it is not as important as the metal-linker bond strength. This demonstration of alignment between experimental and calculated observations has proven the validity of the method, and the insight derived herein insight facilitates direction in designing ideal MOF materials with improved hydrothermal stability for desired applications.

Screening of metal-organic frameworks for carbon dioxide capture from flue gas using a combined experimental and modeling approach.

A diverse collection of 14 metal-organic frameworks (MOFs) was screened for CO(2) capture from flue gas using a combined experimental and modeling approach. Adsorption measurements are reported for the screened MOFs at room temperature up to 1 bar. These data are used to validate a generalized strategy for molecular modeling of CO(2) and other small molecules in MOFs. MOFs possessing a high density of open metal sites are found to adsorb significant amounts of CO(2) even at low pressure. An excellent correlation is found between the heat of adsorption and the amount of CO(2) adsorbed below 1 bar. Molecular modeling can aid in selection of adsorbents for CO(2) capture from flue gas by screening a large number of MOFs.

Get the light out: nanoscaling MOFs for luminescence sensing and optical applications.

Optical transparency is a critical but often overlooked property of MOFs considered for optical applications and luminescence sensing. Zr-1,4-NDC samples with various crystallite dimensions (35 nm to 100 µm) were prepared and their bulk optical transmittance measured. The nanocrystalline (35 nm) sample exhibited the highest optical transmittance, which boosts the luminescence signal for sensing applications by reducing scattering loss.

IRMOF-74(n)-Mg: a novel catalyst series for hydrogen activation and hydrogenolysis of C-O bonds.

Metal-Organic Frameworks (MOFs) that catalyze hydrogenolysis reactions are rare and there is little understanding of how the MOF, hydrogen, and substrate molecules interact. In this regard, the isoreticular IRMOF-74 series, two of which are known catalysts for hydrogenolysis of aromatic C-O bonds, provides an unusual opportunity for systematic probing of these reactions. The diameter of the 1D open channels can be varied within a common topology owing to the common secondary building unit (SBU) and controllable length of the hydroxy-carboxylate struts. We show that the first four members of the IRMOF-74(Mg) series are inherently catalytic for aromatic C-O bond hydrogenolysis and that the conversion varies non-monotonically with pore size. These catalysts are recyclable and reusable, retaining their crystallinity and framework structure after the hydrogenolysis reaction. The hydrogenolysis conversion of phenylethylphenyl ether (PPE), benzylphenyl ether (BPE), and diphenyl ether (DPE) varies as PPE > BPE > DPE, consistent with the strength of the C-O bond. Counterintuitively, however, the conversion also follows the trend IRMOF-74(III) > IRMOF-74(IV) > IRMOF-74(II) > IRMOF-74(I), with little variation in the corresponding selectivity. DFT calculations suggest the unexpected behavior is due to much stronger ether and phenol binding to the Mg(ii) open metal sites (OMS) of IRMOF-74(III), resulting from a structural distortion that moves the Mg2+ ions toward the interior of the pore. Solid-state 25Mg NMR data indicate that both H2 and ether molecules interact with the Mg(ii) OMS and hydrogen-deuterium exchange reactions show that these MOFs activate dihydrogen bonds. The results suggest that both confinement and the presence of reactive metals are essential for achieving the high catalytic activity, but that subtle variations in pore structure can significantly affect the catalysis. Moreover, they challenge the notion that simply increasing MOF pore size within a constant topology will lead to higher conversions.

The effect of pyridine modification of Ni-DOBDC on CO2 capture under humid conditions.

The metal-organic framework Ni-DOBDC was modified with pyridine molecules to make the normally hydrophilic internal surface more hydrophobic. Experiments and molecular simulations show that the pyridine modification reduces H2O adsorption while retaining substantial CO2 capacity under the conditions of interest for carbon capture from flue gas.

Porous, crystalline, covalent organic frameworks.

Covalent organic frameworks (COFs) have been designed and successfully synthesized by condensation reactions of phenyl diboronic acid {C6H4[B(OH)2]2} and hexahydroxytriphenylene [C18H6(OH)6]. Powder x-ray diffraction studies of the highly crystalline products (C3H2BO)6.(C9H12)1 (COF-1) and C9H4BO2 (COF-5) revealed expanded porous graphitic layers that are either staggered (COF-1, P6(3)/mmc) or eclipsed (COF-5, P6/mmm). Their crystal structures are entirely held by strong bonds between B, C, and O atoms to form rigid porous architectures with pore sizes ranging from 7 to 27 angstroms. COF-1 and COF-5 exhibit high thermal stability (to temperatures up to 500 degrees to 600 degrees C), permanent porosity, and high surface areas (711 and 1590 square meters per gram, respectively).