RESUMO
Occupational exposure to airborne dust is responsible for numerous respiratory and cardiovascular diseases. Because of these hazards, air samples are regularly collected on filters and sent for laboratory analysis to ensure compliance with regulations. Unfortunately, this approach often takes weeks to provide a result, which makes it impossible to identify dust sources or protect workers in real time. To address these challenges, we developed a system that characterizes airborne dust by its spectro-chemical profile. In this device, a micro-cyclone concentrates particles from the air and introduces them into a hollow waveguide where an infrared signature is obtained. An algorithm is then used to quantitate the composition of respirable particles by incorporating the infrared features of the most relevant chemical groups and compensating for Mie scattering. With this approach, the system can successfully differentiate mixtures of inorganic materials associated with construction sites in near-real time. The use of a free-space optic assembly improves the light throughput significantly, which enables detection limits of approximately 10 µg/m3 with a 10 minute sampling time. While respirable crystalline silica was the focus of this work, it is hoped that the flexibility of the platform will enable different aerosols to be detected in other occupational settings.
RESUMO
Liquid Natural Gas (LNG) is an energy source that is becoming more important in energy transition, as the world is facing lower the CO2 emissions and backup sources for wind and solar energy are needed. LNG is becoming a major player not only as fuel for power plants, but also in transport and mobility. However, the composition of LNG varies significantly between the various production locations around the world, and the layering of hydrocarbons with different molecular weights takes place even in LNG containers. This is especially critical for LNG engines, in which the ignition properties of the gas depend heavily on the fuel quality or Methane Number (MN) of the gas. For optimized engine operation and motor management, this fuel quality should be measured regularly, preferably online and by a small and low-cost sensor. This paper presents two sensor solutions for the assessment of the full gas composition. For both sensors, the standard deviation in the composition of the relevant hydrocarbons was low enough to calculate the Methane Number with an accuracy of approximately 1 MN unit. It was demonstrated that the electronic capacitive sensor was better suited to assess the higher hydrocarbons, whereas the infrared sensor showed higher selectivity for the lower hydrocarbons.
RESUMO
The health and environmental effects of particulate matter (PM) in the air depend on several parameters. Besides particle size, shape, and concentration, the chemical nature of the PM is also of great importance. State-of-the-art PM sensors only detect the particle size and concentration. Small, low-cost sensors only identify PM according to PM2.5 and PM10 standards. Larger detectors measure the complete particle size distribution. However, the chemical composition of PM is not often assessed. The current paper presents the initial stages of the development of an infrared-based detector for the inline assessment of the chemistry of PM in the air. By combining a mini cyclone that is able to concentrate the particles at least a thousand fold and a hollow waveguide that aligns the flow of particles with infrared light, the feasibility of the concept was shown in this study. A clear differentiation between amorphous and crystalline silica was demonstrated at outdoor PM levels of lower than 1 mg per cubic meter.
RESUMO
Single and multi-layer passive optical interconnects using single mode polymer waveguides are demonstrated using UV nano-imprint lithography. The fabrication tolerances associated with imprint lithography are investigated and we show a way to experimentally quantify a small variation in index contrast between core and cladding of fabricated devices. 1x2 splitting devices based on directional couplers and multimode interference interferometers are demonstrated to have less than 0.45 dB insertion loss with 0.02 ± 0.01 dB power imbalance between the outputs. We demonstrate an 'optical via' with an insertion loss less than 0.45 dB to transfer light from one optical signal plane to another. A 1x4 two-dimensional optical port is experimentally demonstrated to spatially split the input power with an insertion loss of 1.2 dB.
RESUMO
Micro- and nanoplastics have been detected in environmental compartments from the highest mountains to the deepest seas. They have been shown to be present at almost all trophic levels, and within humans they have been detected in numerous organs and human stool. Whilst their ubiquitous nature is indisputable, little is known about the health risks they may present. Much current research is focussed on the production of test materials with which to perform the necessary health studies. An important aspect of this is the correct storage and suspension of the materials to ensure they remain stable both chemically and with regards to size and shape. In this review, we look at the chemical stability of nine common polymers in a range of liquids; first with the use of commercial compatibility charts and then with a more quantitative approach using Hansen solubility parameters. We then look at stability with regards to particle agglomeration, whether and how stable compositions can be predicted, and which dispersants can be added to increase stability. Finally, we discuss the role of bio-surfactants and the eco-corona and how these may offer a route to both better stability and environmental relevance.
Assuntos
Microplásticos , Tensoativos , Tensoativos/química , Tensoativos/toxicidade , Microplásticos/toxicidade , Humanos , Polímeros/química , Monitoramento Ambiental/métodos , Nanopartículas/toxicidade , Nanopartículas/químicaRESUMO
The presence of microplastics in environmental compartments is generally recognized as a (potential) health risk. Many papers have been published on the abundance of microplastics at various locations around the globe, but only limited knowledge is available on possible mitigation routes. One of the mitigation routes is based on the choice of plastic materials used for products that may unintentionally end up in the environment. As a first approach, this paper presents a method to calculate the tendency of polymers to form microplastics, based on their mechanical and physical properties. A MicroPlastic Index (MPI) that correlates the microplastic formation to polymer properties is defined for both impact and wear of polymers via a theoretical particle size and the energy required to form these particles. A first comparison between calculated and experimental particle size is included. The MPI for impact and wear follow the same trend. Finally, these MPIs are correlated to the respective abundance of the microplastics in the environment, corrected for global production of the corresponding polymers: the higher the MPI, the more microplastics are found in the environment. Thus, the MPI can be used as a basis for choice or redesign of polymers to reduce microplastic formation.
RESUMO
The energy market is facing a major transition, in which natural gas and renewable gasses will play an important role. However, changing gas sources and compositions will force the gas transporters, gas engine manufacturers, and gas grid operators to monitor the gas quality in a more intensive way. This leads to the need for lower cost, smaller, and easy to install gas quality sensors. A new approach is proposed in this study that is based on the chemical interactions of the various gas components and responsive layers applied to an array of capacitive interdigitated electrodes. For Liquid Natural Gas (LNG), containing a relative high concentration of higher hydrocarbons, an array of ten capacitive chips is proposed, that is sufficient to calculate the full composition, and can be used to calculate energy parameters, such as Wobbe Index, Calorific Value, and Methane Number. A first prototype was realized that was small enough to be inserted in low and medium pressure gas pipes and LNG engine fuel lines. Adding the pressure and temperature data to the chip readings enables the determination of the concentrations of the various alkanes, hydrogen, nitrogen, and carbon dioxide, including small fluctuations in water vapor pressure. The sensitivity and selectivity of the new sensor is compared to a compact analyzer employing tunable filter infrared spectrometry.
RESUMO
Wrinkling of elastomeric coatings by an electric field is reported. The associated changes in the coating's optical properties yield switchable mirrors and windows. The field Ec needed to induce wrinkling is a factor of 4.4 lower than the theoretically predicted value, which is attributed to space-charge injection.
RESUMO
INTRODUCTION: The limited availability of fossil fuel sources, worldwide rising energy demands and anticipated climate changes attributed to an increase of greenhouse gasses are important driving forces for finding alternative energy sources. One approach to meeting the increasing energy demands and reduction of greenhouse gas emissions is by large-scale substitution of petrochemically derived transport fuels by the use of carbon dioxide-neutral biofuels, such as ethanol derived from lignocellulosic material. RESULTS: This paper describes an integrated pilot-scale process where lime-treated wheat straw with a high dry-matter content (around 35% by weight) is converted to ethanol via simultaneous saccharification and fermentation by commercial hydrolytic enzymes and bakers' yeast (Saccharomyces cerevisiae). After 53 hours of incubation, an ethanol concentration of 21.4 g/liter was detected, corresponding to a 48% glucan-to-ethanol conversion of the theoretical maximum. The xylan fraction remained mostly in the soluble oligomeric form (52%) in the fermentation broth, probably due to the inability of this yeast to convert pentoses. A preliminary assessment of the distilled ethanol quality showed that it meets transportation ethanol fuel specifications. The distillation residue, which contained non-hydrolysable and non-fermentable (in)organic compounds, was divided into a liquid and solid fraction. The liquid fraction served as substrate for the production of biogas (methane), whereas the solid fraction functioned as fuel for thermal conversion (combustion), yielding thermal energy, which can be used for heat and power generation. CONCLUSION: Based on the achieved experimental values, 16.7 kg of pretreated wheat straw could be converted to 1.7 kg of ethanol, 1.1 kg of methane, 4.1 kg of carbon dioxide, around 3.4 kg of compost and 6.6 kg of lignin-rich residue. The higher heating value of the lignin-rich residue was 13.4 MJ thermal energy per kilogram (dry basis).