Finishing technique effect on strength of zirconia-reinforced lithium silicate ceramic.

The aim of this study was to evaluate the effect of two finishing techniques, glazing or polishing, in comparison with the as-cut condition, on the biaxial-flexural-strength (BFS) of a zirconia-reinforced lithium silicate ceramic (ZLS). Cylinders were milled from CAD/CAM blocks and sliced to obtain disc-shaped specimens (ISO6872:2015). Polished and glazed specimens were processed following the manufacturer's instructions. Thirty-three specimens were obtained for each condition and microstructural and BFS/fractographic characterizations were performed. BFS and roughness data were analyzed using Weibull statistics and ANOVA one-way with Tukey post-hoc test, respectively. While a rougher surface was observed for as-cut specimens, smoother surfaces were observed for polished and glazed ZLS at microscopical evaluation and confirmed through surface-roughness evaluation. X-ray spectra depicted a glass phase for all groups and characteristic metasilicate, lithium disilicate, and lithium phosphate peaks for the as-cut and polished specimens. Glazed specimens showed higher characteristic strength than polished and as-cut specimens, which did not differ significantly. While higher Weibull-modulus was observed for the polished than for the as-cut specimens, no statistically significant differences were noted between glazed and polished, and between glazed and as-cut specimens. ZLS presents higher strength when glazed, and polishing increases the structural reliability of the material relative to the as-cut condition. Both finishing techniques reduced surface roughness similarly.

Influence of ceramic thickness and dental substrate on the survival rate and failure load of non-retentive occlusal veneers after fatigue.

OBJECTIVE: To investigate the effect of ceramic thickness and dental substrate (enamel vs. dentin/enamel) on the survival rate and failure load of non-retentive occlusal veneers. MATERIALS AND METHODS: Human maxillary molars (n = 60) were divided into five test-groups (n = 12). The groups (named DE-1.5, DE-1.0, DE-0.5, E-1.0, E-0.5) differed in their dental substrate (E = enamel, DE = dentin/enamel) and restoration thickness (standard: 1.5 mm, thin: 1.0 mm, ultrathin: 0.5 mm). All teeth were prepared for non-retentive monolithic lithium-disilicate occlusal veneers (IPS e.max Press, Ivoclar). Restorations were adhesively cemented (Syntac Classic/Variolink II, Ivoclar) and exposed to thermomechanical fatigue (1.2 million cycles, 1.6 Hz, 49 N/ 5-55°C). Single load to failure was performed using a universal testing-machine. A linear-regression model was applied, pairwise comparisons used the Student-Newman-Keuls method (p < 0.05). RESULTS: Three dentin-based occlusal veneers (one DE-1.0, two DE-0.5) revealed cracks after fatigue exposure, which corresponds to an overall-survival rate of 95%. Load to failure resulted in the following ranking: 2142 N(DE-0.5) > 2105 N(E-1.0) > 2075 N(E-0.5) > 1440 N(DE-1.5) > 1430 N(DE-1.0). Thin (E-1.0) and ultrathin enamel-based occlusal veneers (E-0.5) revealed high failure loads and surpassed the standard thickness dentin-based veneers (DE-1.5) significantly (p = 0.044, p = 0.022). CONCLUSION: All tested monolithic lithium disilicate occlusal veneers obtained failure loads above physiological chewing forces. Thin and ultrathin enamel-based occlusal veneers outperformed the standard thick dentin-based occlusal veneers. CLINICAL SIGNIFICANCE: Minimally invasive enamel-based occlusal veneer restorations with non-retentive preparation design may serve as a conservative treatment option.

Ultrathin lithium disilicate and translucent zirconia crowns for posterior teeth: Survival and failure modes.

PURPOSE: To evaluate the reliability and failure modes of ultrathin (0.5 mm) lithium disilicate, translucent and ultra-translucent zirconia crowns for posterior teeth restorations. MATERIALS AND METHODS: Fifty-four mandibular first molar crowns of three ceramic materials: (1) Lithium disilicate (e.max CAD, Ivoclar Vivadent), (2) 3Y-TZP (Zirconn Translucent, Vipi), and (3) 5Y-PSZ (Cercon XT, Dentsply Sirona), with 0.5 mm of thickness were milled and cemented onto composite resin abutments. Eighteen samples of each group were tested under mouth-motion step-stress accelerated life testing in a humid environment using mild, moderate, and aggressive profiles. Data was subjected to Weibull statistics. Use level curves were plotted and reliability was calculated for a given mission of 100,000 cycles at 100, 200, and 300 N. Fractographic analyses of representative samples were performed in scanning electron microscope. RESULTS: Beta (ß) values suggest that failures were dictated by material's strength for lithium disilicate and by fatigue damage accumulation for both zirconias. No significant differences were detected in Weibull modulus and characteristic strength among groups. At a given mission of 100,000 cycles at 100 N, lithium disilicate presented higher reliability (98% CB: 95-99) regarding 3Y-TZP and 5Y-PSZ groups (84% CB: 65%-93% and 79% CB: 37&-94%, respectively). At 200 N, lithium disilicate reliability (82% CB: 66%-91%) was higher than 5Y-PSZ (20% CB: 4%-44%) and not significantly different from 3Y-TZP (54% CB: 32%-72%). Furthermore, at 300 N no significant differences in reliability were detected among groups, with a notable reduction in the reliability of all materials. Fractographic analyses showed that crack initiated at the interface between the composite core and the ceramic crowns due to tensile stress generated at the intaglio surface. CONCLUSIONS: Ultrathin lithium disilicate crowns demonstrated higher reliability relative to zirconia crowns at functional loads. Lithium disilicate and zirconia crown's reliability decreased significantly for missions at higher loads and similar failure modes were observed regardless of crown material. The indication of 0.5 mm thickness crowns in high-load bearing regions must be carefully evaluated. CLINICAL SIGNIFICANCE: Ultraconservative lithium disilicate and zirconia crowns of 0.5 mm thickness may be indicated in anterior restorations and pre-molars. Their clinical indication in high-load requirement regions must be carefully evaluated.

Hydrofluoric acid concentration and etching time affect differently the microstructure and surface properties of pressed lithium disilicate glass ceramics.

OBJECTIVE: To evaluate the effect of different hydrofluoric acid concentrations and etching times on the surface, chemical composition and microstructure of lithium disilicate. MATERIAL AND METHODS: Ninety specimens of pressed lithium disilicate (LDS) were obtained (IPS e.max Press, Rosetta SP and LiSi Press). The specimens of each material were divided in two groups according to the hydrofluoric acid concentration: 5% and 10% (n = 15/group), and subdivided according to the etching time: 20, 40 and 60 s (n = 5/group). Crystalline evaluations and chemical composition were performed through x-ray diffraction (XRD) and energy-dispersive x-ray spectroscopy (EDS), respectively. Microstructural analyses were performed by scanning electron microscope (SEM), surface roughness (Ra), and material thickness removal evaluation. Thickness removal and Ra data were analyzed by ANOVA and Tukey test (p < 0.05). RESULTS: XRD demonstrated characteristic peaks of lithium disilicate crystals, lithium phosphate and of a vitreous phase for all materials. EDS identified different compositions and SEM confirmed different surface responses to acid etching protocols. Material and etching time influenced Ra and material thickness removal (p < 0.05). CONCLUSION: Hydrofluoric acid concentration and etching time affect the surface characteristics of LDS differently. LiSi Press presented higher resistance to hydrofluoric acid etching compared to e.max Press and Rosetta SP. CLINICAL SIGNIFICANCE: Applying the appropriate etching protocol is pivotal to avoid excessive material removal and to prevent jeopardize the mechanical and optical properties of the material.

Reliability and lifetime of lithium disilicate, 3Y-TZP, and 5Y-TZP zirconia crowns with different occlusal thicknesses.

OBJECTIVES: To assess the probability of survival of crowns made with a 3Y-TZP, a 5Y-TZP, and a lithium disilicate. MATERIALS AND METHODS: CAD-CAM premolar crowns with occlusal thicknesses of 1.0 mm or 1.5 mm and cemented on a metal dye. Step-stress accelerated life testing (SSALT) was performed to access the use level probability Weibull curves and reliability were calculated for the completion of a mission of 100,000 cycles at 300 to 1200 N. RESULTS: All ceramics showed a high probability of survival (87-99%) at 300 N, irrespective of thickness. 3Y-TZP shows no significant decrease in the probability of survival up to 1200 N (83-96%). Lithium disilicate presented lower reliability than zirconia under the 600 N mission. 5Y-TZP showed lower reliability than 3Y-TZP at 1200 N. There was no significant difference in the Weibull modulus (3.23-7.12). 3Y-TZP had the highest characteristic strength (2483-2972 N), followed by 5Y-TZP (1512-1547 N) and lithium disilicate (971-1154 N). CONCLUSION: Zirconia ceramics have a high probability of survival (up to 900 N-load), while lithium disilicate survives up to 300 N load only, irrespective of the thickness (1.0 mm or 1.5 mm). CLINICAL RELEVANCE: The probability of survival of posterior crowns made with zirconia ceramics resists extreme loads while glass ceramics resist normal chewing loads. In addition, crowns with thinner occlusal face showed sufficient mechanical behavior.

Fiber-reinforced composite full-arch prosthetic reconstructions supported by three standard, short or extra-short implants: a two-center retrospective study.

OBJECTIVES: To evaluate the survival of implants and prostheses, and marginal bone level of fiber-reinforced composite implant supported fixed complete prostheses supported by 3 implants. MATERIALS AND METHODS: Patients with fiber-reinforced composite fixed prostheses supported by 3 standard-length, short or extra-short implants were included in this retrospective cohort study. Kaplan-Meier survival was computed for implants and prostheses. Univariate and multivariate Cox proportional hazard regressions, clustered by patient, were used to analyze bone level differences as a function of different study covariates. Linear regressions were used to investigate the relationship between distal extension lengths and bone levels. RESULTS: Forty-five patients with 138 implants were followed for up to 10 years after prosthesis insertion (mean 52.8; SD 20.5 months). Kaplan-Meier survival analysis showed overall survival rates of 96.5% for implants and of 97.8% for prostheses. The 10-year success rate for prostheses was 90.8%. Extra-short implants survived at similar rates to short and standard implants. Marginal bone levels surrounding implants remained stable over time, even showing slight bone gain on average (mean + 0.1 mm/year; SD ± 0.5 mm/year) Acrylic denture teeth, overdentures on the opposing arch, and implant placement in the posterior maxilla were correlated with bone gain. Screw retention, opposed to telescopic retention, was correlated with bone loss. Longer distal extensions were correlated with bone gain on the implants closest to the distal extensions. CONCLUSIONS: Fiber-reinforced composite fixed prostheses supported by only 3 implants, most of which were extra-short, presented high survival rates with stable bone levels. CLINICAL RELEVANCE: An encouraging prognosis can be expected for restoration of atrophic maxillary and mandibular arches, when restored with fixed fiber-reinforced composite frameworks with long distal extensions and supported on only 3 short implants.

Indirect restorative systems-A narrative review.

OBJECTIVE: The background and clinical understanding of the properties of currently available indirect restorative systems and fabrication methods is, along with manufacturer and evidence-based literature, an important starting point to guide the clinical selection of materials for tooth and/or implant supported reconstructions. Therefore, this review explores most indirect restorative systems available in the market, especially all-ceramic, along with aspects of manufacturing process, clinical survival rates, and esthetic outcomes. OVERVIEW: Progressive incorporation of new technologies in the dental field and advancements in materials science have enabled the development/improvement of indirect restorative systems and treatment concepts in oral rehabilitation, resulting in reliable and predictable workflows and successful esthetic and functional outcomes. Indirect restorative systems have evolved from metal ceramics and polymers to glass ceramics, polycrystalline ceramics, and resin-matrix ceramics, aiming to improve not only biological and mechanical properties, but especially the optical properties and esthetic quality of the reconstructions, in attempt to mimic natural teeth. CONCLUSIONS: Based on several clinical research, materials, and patient-related parameters, a decision tree for the selection of indirect restorative materials was suggested to guide clinicians in the rehabilitation process. CLINICAL SIGNIFICANCE: The pace of materials development is faster than that of clinical research aimed to support their use. Since no single material provides an ideal solution to every case, professionals must continuously seek information from well designed, long-term clinical trials in order to incorporate or not new materials and technological advancements.

In vitro assessment of the effect of luting agents, abutment height, and fatigue on the retention of zirconia crowns luted to titanium base implant abutments.

STATEMENT OF PROBLEM: The bonding of implant-supported prostheses is determined by abutment material, convergence angle, height, surface treatment, and luting agents. However, studies evaluating the bonding of luting agents to titanium base abutments with different heights under fatigue conditions are scarce. PURPOSE: The purpose of this in vitro study was to evaluate the retention of zirconia crowns bonded with different luting agents to titanium base abutments of different heights before and after fatigue testing. MATERIAL AND METHODS: Zirconia crowns were designed, milled, and distributed into 4 experimental groups according to the luting agents (G-Multi Primer/G-Cem LinkForce [MP/GC] and Scotchbond Universal/RelyX Ultimate [SU/RU]) and titanium base abutment heights (2.5 mm and 4 mm) (n=10). Pull-out testing was performed in a universal testing machine at a crosshead speed of 1 mm/min until crown displacement. Fatigue testing was performed by an electric precision fatigue simulator (1×106 cycles; 100 N; and 15 Hz), followed by pull-out testing of fatigued specimens. Collected data were statistically evaluated by using a linear mixed model after post hoc comparisons by the least significant difference test (α=.05). RESULTS: Luting agents, abutment heights, and fatigue influenced the bonding retention of zirconia crowns to titanium base abutments. SU/RU agents promoted higher pull-out compared with MP/GC for both abutment heights before and after fatigue. Higher abutment height increased pull-out regarding lower abutment height for SU/RU materials before and after fatigue testing. Although fatigue had no significant effect on the pull-out of MP/GC, lower bond retention was observed for SU/RU after fatigue, regardless of abutment height. CONCLUSIONS: Luting agent composition and the interaction with abutment height and fatigue influenced the retention of zirconia crowns to titanium base abutments.

Success Rate of Mandible Implants Placed in Vascularized Fibula Bone Graft: A Systematic Review.

This systematic review addressed the implant success rate after mandible reconstruction with vascularized fibula bone graft. Therefore, preferred reporting items for systematic review and meta-analysis guidelines were used to perform the systematic review, and the search included following databases: PubMed, Lilacs, Google Scholar, Open Gray, Science Direct and Cochrane. A search of medical subject headings (MeSH) and related terms (fibula) OR (vascularized) OR (microvascularized) AND (implant) OR (rehabilitation) OR (osseointegrated) AND (mandible) OR (jaw) OR (maxillofacial), without any language or time restrictions until October 2017 was carried out. The eligible studies primarily consisted of clinical cohorts designed to evaluate the feasibility of mandible reconstruction using vascularized fibula bone grafts and implant-supported rehabilitations, with a minimum observation period of 12 months. After screening, 13 eligible cohort studies for this review were selected (3 retrospective and 10 prospective). Of 285 vascularized fibular reconstructions, only 6 failures were reported with a success rate of approximately 98% after a mean follow-up period of 40 months. In total, 910 implants were placed in vascularized fibular grafts with a success rate of 92.6% (range, 82%-100%) after 40 months. Also, similar success rates for primary (95%; range, 93%-100%) and secondary (91%; range, 83%-100%) implant surgeries have been demonstrated. Considering risk factors, implant survival in irradiated patients was usually lower (76%; range, 38%-88%) than nonirradiated patients (90%; range, 83%-94%); however, it was significantly different in only 1 study. Alcohol and tobacco use has shown no significant association with implant failure in any study. Hence, implant placement in vascularized fibula bone graft presented similar success rates relative to native mandible bone rehabilitations.

Mechanical Properties, Wear Resistance, and Reliability of Two CAD-CAM Resin Matrix Ceramics.

Background and Objectives: There are limited data regarding the behavior of resin matrix ceramics for current CAD-CAM materials. Further studies may be beneficial and can help clinicians planning to use these materials during prosthodontic rehabilitation. The aim of this study was to evaluate and compare the flexural strength and strain distributions, filler content, wear, and reliability of two resin matrix ceramic CAD-CAM materials. Materials and Methods: Two resin matrix ceramics, Ambarino High-Class (AH) and Vita Enamic (VE), were tested for flexural strength (n = 24), wear (n = 10), and reliability (n = 18). Thermogravimetric analysis was used to determine the percentage of filler by weight, and digital image correlation (DIC) was used for strain analysis in flexural strength test. Reliability of each resin matrix ceramic was compared after accelerated lifetime testing of crowns using a two-parameter Weibull distribution. Data of flexural strength, wear, and thermogravimetry were analyzed by independent t-tests with significance level at 5%. Results: The results of DIC analysis were analyzed by a qualitative comparison between the images obtained. The materials tested showed different flexural strength (p < 0.05) and strain distributions. The filler content was the same as informed by manufacturers. No difference was observed in the wear or reliability analysis (p > 0.05). The flexural strength of material AH was superior to VE, and the strain distribution was compatible with this finding. Conclusions: The two resin matrix ceramics tested showed similar behavior in wear and reliability analysis. Both can provide safe use for dental crowns.

Severely Atrophic Mandibles Restored With Fiber-Reinforced Composite Prostheses Supported by 5.0-mm Ultra-Short Implants Present High Survival Rates Up To Eight Years.

PURPOSE: Encouraging results have been reported for ultrashort single implants; however, long-term investigations are warranted for full-arch reconstructions. This study evaluated marginal bone loss, implant, and reconstruction survival of fiber-reinforced composite full-arch prostheses supported by 4 ultrashort implants. METHODS: Patients with severely atrophic mandibles (Cawood and Howell class V and class VI) were included in this cohort study. Study predictors included time (initial and last follow-up) and vertical (epicrestally or subcrestally) and horizontal implant position (medial or lateral). Outcome variables included bone level changes over time, implant/prosthesis survival. Peri-implant bone level was measured on panoramic radiographs. Descriptive statistics, Kaplan-Meier, mixed model analysis of variance, and univariate and multivariate Cox Proportional Hazards Regression models, adjusted for multiple implants in the same patient, were used for data analyses. RESULTS: Eighteen patients (mean 61.22 years old), with 72 implants placed in atrophic mandibles with an average follow-up of 55.4 months (CI, ±4.6/ SD, ±10.6 months) were analyzed. The implant survival rate was 97.2% as 2 implants were not loaded due to non-osseointegration and sensorial disturbances. Average marginal bone level at baseline (1.93 mm) and at the time of last recall (1.91 mm) was not significantly different. While implants placed subcrestally showed no significant difference between baseline (1.91 mm) and last follow up bone level (2.12 mm), implants placed epicrestally demonstrated a significant reduction on their bone level over time (initial: 1.97 mm/ final:1.33 mm). Systemic disorders were a risk factor for implant survival and bone loss. Prostheses cumulative survival rate was 100% (mean observation period of 55 months). The estimated survival rate after the 96-month follow-up was 75% (1 framework fracture after 84 months). CONCLUSION: Fixed fiber-reinforced composite full-arch prostheses retained by 4 ultrashort implants showed a stable bone level and high implant/prostheses survival rates up to 8 years.

Antiresorptive therapy and dental implant survival: an up to 20-year retrospective cohort study in women.

OBJECTIVES: To investigate the effects of antiresorptive treatment on the survival of plateau-root form dental implants. MATERIALS AND METHODS: Patients undergoing antiresorptive therapy via oral or intravenous administration as well as patients not undergoing antiresorptive therapy and healthy control patients were included in this retrospective cohort study. In total, 1472 implants placed in 631 postmenopausal patients (M: 66.42 ± 9.10 years old), who were followed for a period of up to 20 years (8.78 ± 5.68 years). Kaplan-Meier survival analysis was performed, and univariate and multivariate Cox regression, clustered by each patient, was used to evaluate and study factors affecting the survival of their implants. RESULTS: Implants placed in patients undergoing oral antiresorptive treatment presented significantly higher survival rates, than implants placed in the osteoporosis/osteopenia control cohort (p value < 0.001), and similar survival rates, when compared to healthy controls (p value = 0.03). Additionally, clustered univariate and multivariate Cox regression analysis also revealed higher implant survival when oral antiresorptive drugs (p value = 0.01 and 0.007, respectively) were used, and lower implant survival in the presence of untreated osteoporosis/osteopenia (p value = 0.002 and 0.005, respectively). Overall, the 20-year implant survival in osteoporotic patients undergoing antiresorptive therapy was 94%. For the failed implants, newly replaced implants in patients under antiresorptive treatment presented a 10-year survival of 89%. CONCLUSIONS: Long-term plateau-root form implant survival in osteoporotic patients taking oral antiresorptives was similar to a healthy population and significantly higher than the untreated controls. CLINICAL RELEVANCE: These results suggest that plateau-root form implants provide a robust solution for treating tooth loss in patients, who are undergoing antiresorptive therapy.

Posterior minimally invasive full-veneers: Effect of ceramic thicknesses, bonding substrate, and preparation designs on failure-load and -mode after fatigue.

OBJECTIVE: To evaluate the effect of ceramic thicknesses, bonding surface (enamel vs. dentin), and preparation design (box vs. no box) on the fatigue survival and failure load of minimally invasive full-veneer restorations. MATERIALS AND METHODS: Human-premolars (n = 60) were divided into five test groups (n = 12). All teeth received full-veneer preparation with the following occlusal/labial thicknesses: standard: 1.5/0.8 mm; thin: 1.0/0.6 mm; ultrathin 0.5/0.4 mm. Preparations for each ceramic thickness were refined in enamel (E-1.0 and E-0.5) or dentin (D-1.5, D-1.0, and D-0.5). Control groups DB-1.5, EB-1.0, and EB-0.5 received box preparations. Monolithic lithium disilicate restorations (IPS-e.max-Press, Ivoclar Vivadent) were adhesively cemented (Syntac-Classic/Variolink-II, Ivoclar Vivadent) and subjected to cyclic mechanical loading (F = 49 N, 1.2 million cycles) with simultaneous thermocycling (5-55°C). All specimens were exposed to single load-to-failure. Pair-wise differences were calculated by using a linear regression model and Student-Newman-Keuls method (p < 0.05). RESULTS: All full-veneers of group D-1.5, E-1.0, E-0.5, DB-1.5, EB-1.0, and EB-0.5 survived fatigue. Two full-veneers (D-1.0 and D-0.5) revealed cracks during fatigue, resulting in an overall fatigue survival rate of 98.1%. Mean load-to-failure values (N) were as followed: 1005 (D-1.5); 866 (D-1.0); 816 (D-0.5); 1495 (E-1.0); 1279 (E-0.5); 1129 (DB-1.5); 1087 (EB-1.0); and 833 (EB-0.5). Irrespective of ceramic thicknesses, enamel-based full-veneers resulted in higher failure loads than dentin-based restorations. Box preparation reduced the failure loads of thin and ultrathin enamel-based restorations. CONCLUSION: All tested monolithic lithium disilicate full-veneer restorations exceeded physiological masticatory forces. Minimally invasive full-veneer restorations with enamel as a bonding surface and a non-retentive preparation design showed superior performance. CLINICAL SIGNIFICANCE: Enamel-based non-retentive full-veneers made of monolithic lithium disilicate may serve as a reliable and esthetical minimally invasive treatment option for premolars.

Correlation between 2D and 3D measurements of cement space in CAD-CAM crowns.

STATEMENT OF PROBLEM: Although the 2D analysis of prosthesis cementation space has been popular, its correlation with volumetric comparison (3D data) of cement space is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the cement space in computer-aided design and computer-aided manufacturing (CAD-CAM) crowns of different materials and correlate 2D measurements of cement space with their corresponding 3D values (volume of cement space) by using microcomputed tomography (µCT) analysis of regions of interest. MATERIAL AND METHODS: Ten molar crowns were milled in lithium disilicate (LD), resin nanoceramic (RN), and zirconia (Z) ceramics. Silicone replicas were produced and used as the analog cement layer and scanned with a desktop X-ray microfocus CT scanner. Twenty-eight slices were evaluated in 3 regions: marginal, axial, and occlusal (n=84 measurement points/specimen). After 3D reconstruction of the cement space, the volume was calculated. Data were statistically evaluated through 2-way ANOVA and Bonferroni test (α=.05). The Pearson correlation test was used to investigate the correlation between the 2D and 3D data. RESULTS: The volumes of the occlusal (LD 10 ±1 mm3; RN 9 ±1 mm3) and axial regions (LD 9 ±2 mm3; RN 8 ±1 mm3) were significantly higher than the volume of the marginal region for LD and RN specimens (LD 6 ±2 mm3; RN 4 ±1 mm3) (both P<.001). For the Z group, the axial region had the highest volume (19 ±2 mm3), followed by the volumes of the occlusal (15 ±1 mm3) and marginal regions (12 ±1 mm3). The Pearson correlation test determined a moderate positive correlation of the marginal area (r=0.606, P<.001) and of the axial region (r=0.588, P<.001). However, a moderate negative correlation was found between volume and thickness of the occlusal area (r=-0.437, P=.016). CONCLUSIONS: Z showed more volume of cement space, as well as thicker cement space than LD and RN. The µCT analysis is an efficient method of analyzing cement thickness and volume in ceramic crowns at the selected regions of interest. A moderate positive correlation was found between the 2D and 3D analyses for the axial and marginal regions of ceramic crowns.

Impact of rehabilitation with removable complete or partial dentures on masticatory efficiency and quality of life: A cross-sectional mapping study.

STATEMENT OF PROBLEM: Tooth loss directly affects mastication, cognitive function, and oral health-related quality of life (OHRQoL). Complete dentures (CDs) and removable partial dentures (RPDs) represent a common oral rehabilitation approach. However, studies addressing the impact of removable dentures on replacing missing teeth are lacking. PURPOSE: The purpose of this clinical study was to evaluate whether the OHRQoL, the jaw function limitation (JFL), and the masticatory efficiency of CD and RPD wearers are similar to those of patients with natural teeth and to evaluate whether wearing removable dentures can predict an effect on the OHRQoL, JFL, and masticatory efficiency of their wearers. MATERIAL AND METHODS: The Oral Health Impact Profile (OHIP-14) questionnaire and the JFL scale were used to measure OHRQoL and JFL. Masticatory efficiency was analyzed by using a subjective color-mixing index for the chewing gum bolus and shape index and an objective colorimetric analysis by using a software program ViewGum. Data were analyzed with Kruskal-Wallis and post hoc Dunn tests, followed by multiple linear regression (α=.05). RESULTS: The results from OHIP-14 evidenced that both denture groups presented a low impact on OHRQoL. JFL was higher for all denture wearers. For the subjective color-mixing analysis, the control and RPD groups presented better masticatory efficiency than CD wearers. Colorimetric analysis evidenced better masticatory efficiency for the control group, who differed from the CD and RPD groups. Wearing RPDs was a predictor of impaired JFL and OHRQoL, and the use of CDs was a predictor of impaired JFL and masticatory efficiency. CONCLUSIONS: Despite being rehabilitated, CD and RPD wearers still had impaired OHRQoL, JFL, and masticatory efficiency. Also, the use of these prostheses can predict a negative effect on these 3 variables.

Effect of Surgical Instrumentation Variables on the Osseointegration of Narrow- and Wide-Diameter Short Implants.

PURPOSE: The aim of the present study was to systematically analyze how a multifactorial surgical instrumentation approach affects osseointegration on both narrow-diameter and wide-diameter short implants. MATERIALS AND METHODS: Twelve skeletally mature female sheep were used in the study along with 144 plateau-root-form healing chamber titanium (Ti-6Al-4V) implants (Bicon LLC, Boston, MA), evenly distributed between narrow (3.5 mm) and wide (6.0 mm) diameters. The presence or the absence of irrigation, different drilling speeds, and 2 time points quantifying bone-implant contact (BIC) and bone area fraction occupancy (BAFO) to evaluate the osteogenic parameters around the implants. RESULTS: There were no signs of inflammation, infection, or failure of the implants observed at either healing period. The narrow 3.5-mm implant, at 6 weeks, yielded significant differences in terms of BIC at a drilling speed of 50 rotations per minute (RPM), with higher values of the samples using irrigation (30.6 ± 6.1%) compared with those without (19.7 ± 6.1%). No statistical differences were detected for 500 and 1,000 RPM with or without irrigation. The wide 6-mm diameter implant showed differences with respect to drilling speed, 500 and 1,000 RPM, with higher values associated with samples subjected to irrigation. BAFO results, for both diameters, only detected statistical differences between the 2 times (3 vs 6 weeks); no statistical differences were detected when evaluating as a function of time, drilling speed, and irrigation. CONCLUSIONS: Surgical instrumentation variables (ie, drilling speed [RPM] and irrigation) yielded to be more of an effect for BIC at longer healing time (6 weeks) for the wider implants. Furthermore, deploying narrow or wide plateau-root-form implants, where conditions allow, has shown to be a safe alternative, considering the high BIC and BAFO values observed, independent of irrigation.

Mechanical testing of four-unit implant-supported prostheses with extensive pink gingiva porcelain: The dentogingival prostheses proof of concept.

OBJECTIVE: To investigate the probability of survival and failure modes of four-unit implant-supported porcelain fused to metal (PFM) dentogingival prostheses subjected to step-stress accelerated life testing (SSALT). MATERIALS AND METHODS: Eighteen implant-supported PFM dentogingival prostheses with thin metallic infrastructures, which provided minimal ceramic support and improved esthetics were fabricated over external hexagonal connection UCLA abutments. SSALT was performed until specimen failure. Use level probability Weibull curve and reliability were calculated and plotted. Weibull modulus (m) and characteristic strength (η) were also calculated. Polarized light microscope and scanning electron microscope were used to characterize fractures. RESULTS: Failures were dictated by material strength rather than fatigue damage accumulation. The probability of survival for loads reaching 100 and 150 N in 100,000 cycles was 92 and 61%, respectively. No cracks or fractures were identified in the veneered porcelain, whereas abutment fixation screw fracture was the chief failure mode. CONCLUSION: Implant-supported PFM four-unit dentogingival prostheses with minimum metal framework dimensions presented favorable lifetime prediction under fatigue testing. Fractures were restricted to fixation screws. CLINICAL SIGNIFICANCE: In-vitro fatigue testing and failure mode analyses evidenced favorable lifetime prediction for 4-unit implant-supported dentogingival prostheses with minimum metal frameworks. Abutment fixation screw fracture might be the most frequent clinical complication. Since this proof of concept has been tested in-vitro, further studies including different restorative materials, as well as long-term clinical trials are warranted.

Analysis of correlation between optical and microtomography measurements of cementation space in CAD-CAM ceramic crowns.

STATEMENT OF PROBLEM: Identical computer-aided design (CAD) parameters may be used to mill a variety of ceramic materials for computer-aided design and computer-aided manufacture (CAD-CAM) crowns. Whether milled crown spacing matches the designed parameters when more than a single evaluation method is applied is unknown. PURPOSE: The purpose of this in vitro study was to correlate the stereomicroscope and the microcomputer tomography (µCT) 2-dimensional analysis of the cementation space with the replica technique in assessing 3 different ceramic materials. MATERIAL AND METHODS: The specimens were milled in lithium disilicate, resin nanoceramic, and zirconia (n=30). The cement space was measured at the marginal, axial, and occlusal regions. One hundred twenty measurements of each material were used to correlate the methodologies. Data were statistically evaluated with 2-way repeated measures ANOVA and the Tukey test (α=.05). The Pearson correlation coefficient was used for each region for both methodologies (µCT and optical microscopy) separately. RESULTS: For the µCT analysis, no differences were observed (P>.05) among the materials, but the axial region showed a positive correlation with the marginal (r=0.957) and occlusal regions (r=0.349); the same was observed between the occlusal and marginal regions (r=0.338). However, for stereomicroscope evaluation, resin nanoceramic and zirconia present similar cementation space (P=960), both being different from lithium disilicate (P<.05). The marginal region presented a positive correlation with axial (r=0.149) and occlusal regions (r=0.344), but the axial region showed negative correlation with the occlusal surface (r=-0.205). CONCLUSIONS: The measurements of the scanned replicas were accurate when thinner sections were under measurement. Although the same space parameters were set in the CAD software program, definitive internal dimensions varied among the milled crowns.

Static and Fatigue Loading of Veneered Implant-Supported Fixed Dental Prostheses.

PURPOSE: This study aimed to compare the load to failure and the probability of survival of porcelain fused to zirconia (PFZ) three-unit, implant-supported, fixed dental prostheses (FDPs) to those of indirect composites veneered to either zirconia (CVZ) or milled fiber-reinforced composite (FRC) frameworks under static and fatigue loading. MATERIALS AND METHODS: One-hundred and twenty posterior three-unit FDP (second premolar pontic) frameworks were fabricated via milling from a single Standard Tessellation Language (STL) file. The FDPs were divided into three groups. Each group (n = 40) was subjected to static (n = 20) and fatigue (n = 20) loading tests, as follows: (1) PFZ: zirconia framework layered with porcelain veneer; (2) CVZ: zirconia framework veneered with indirect composite resin; and (3) FRC: FRC framework veneered with indirect composite resin. After porcelain veneering onto sintered zirconia frameworks, or resin composite veneering onto zirconia or FRC frameworks, FDPs were cemented on their abutments using self-adhesive resin cement. After thermal cycling, half of the FDPs were subjected to an accelerated fatigue test. The other half of the FDPs were subjected to single load-to-failure (SLF) testing at a crosshead speed (1 mm/min). Lifetime analysis was conducted to determine the probability of survival, and fractographic analysis was performed. RESULTS: Significant differences were observed among the studied groups for SLF with the highest characteristic strength values observed for PFZ (2154 N), followed by 1905.47 N for CVZ and 1679.56 N for FRC. The probability of survival for 100,000 cycles at 500 N was the highest for FRC (98%) and CVZ (100%) and was significantly lower for PFZ (88%). Different fracture patterns were observed in the fractography. CONCLUSIONS: In fatigue testing, which simulates masticatory function better than static tests, a higher probability of survival was observed for FRC and CVZ than for PFZ. Framework fractures were not observed only for the FRC group, indicating that chairside repair with the addition of indirect composite could be performed for continued function.

Biomaterial and biomechanical considerations to prevent risks in implant therapy.

This paper is aimed to present a biomaterials perspective in implant therapy that fosters improved bone response and long-term biomechanical competence from surgical instrumentation to final prosthetic rehabilitation. Strategies to develop implant surface texturing will be presented and their role as an ad hoc treatment discussed in light of the interplay between surgical instrumentation and implant macrogeometric configuration. Evidence from human retrieved implants in service for several years and from in vivo studies will be used to show how the interplay between surgical instrumentation and implant macrogeometry design affect osseointegration healing pathways, and bone morphologic and long-term mechanical properties. Also, the planning of implant-supported prosthetic rehabilitations targeted at long-term performance will be appraised from a standpoint where personal preferences (eg, cementing or screwing a prosthesis) can very often fail to deliver the best patient care. Lastly, the acknowledgement that every rehabilitation will have its strength degraded over time once in function will be highlighted, since the potential occurrence of even minor failures is rarely presented to patients prior to treatment.