Visible-Light Initiated Dispersion Photopolymerization of Styrene.

Polystyrene (PS) particles were synthesized in ethanol/water mixture by dispersion polymerization using visible light irradiation, with either a N-heterocyclic carbene borane-based photoinitiating system (PIS) or a disulfide. With the full PIS and poly(ethylene glycol) methyl ether methacrylate (PEGMA) as stabilizer, the size distributions were broad and the amount of PEGMA had a strong impact on the experiment reproducibility. The addition of a base solved the problem, leading to faster polymerizations, narrower size distributions and larger particles. With the disulfide as sole PIS, bigger and narrowly distributed PS particles were again formed. Quantitative conversion was achieved in each system, with particle size ranging between 100 and 350 nm. The use of poly(N-vinylpyrrolidone) as stabilizer led to significantly larger particles, up to 1.2 µm, with narrow size distributions. The production of such large latex particles by photoinitiated polymerizations is unprecedented.

Development of a Borane-(Meth)acrylate Photo-Click Reaction.

In the development of 3D printing fuels, there is a need for new photoinitiating systems working under mild conditions and/or leading to polymers with new and/or enhanced properties. In this context, we introduce herein N-heterocyclic carbene-borane complexes as reagents for a new type of photo-click reaction, the borane-(meth)acrylate click reaction. Remarkably, the higher bond number of boranes relative to thiols induced an increase of the network density associated with faster polymerization kinetics. Solid-state NMR evidenced the strong participation of the boron centers on the network properties, while DMA and AFM showed that the materials exhibit improved mechanical properties, as well as reduced solvent swelling.

Interaction of Cationic, Anionic, and Nonionic Macroraft Homo- and Copolymers with Laponite Clay.

The functionalization of Laponite RD platelets with different cationic, anionic, and nonionic homo- and copolymers synthesized by reversible addition-fragmentation chain transfer (RAFT) has been investigated. The effective interaction of the macromolecular RAFT agents (macroRAFTs) with the inorganic particles is known to be of crucial importance for the successful coating of minerals with polymers via RAFT-mediated emulsion polymerization to produce polymer-encapsulated inorganic particles. The macroRAFT agents synthesized in the present work contain carefully selected reinitiating R groups, which bear either ionizable tertiary amine or quaternary ammonium moieties (from 2-(dimethylamino)ethyl methacrylate, DMAEMA), negatively charged acrylic acid (AA) repeat units, or neutral polyethylene glycol (PEG) side chains, and are capable of interacting with Laponite via different adsorption mechanisms. The equilibrium adsorption of these RAFT (co)polymers was investigated by the plotting of adsorption isotherms, and either L-type or H-type curves were obtained. The hydrophobicity of the macroRAFT was shown to promote adsorption, as did the pending configuration of the PEG block. Charge repulsion between AA and the negatively charged surface of Laponite at pH 7.5, on the other hand, was prejudicial for adsorption, while the strong electrostatic interaction between the cationic DMAEMA molecules and the Laponite surface led to high-affinity-type curves.

Vitrimer Chemistry Meets Cellulose Nanofibrils: Bioinspired Nanopapers with High Water Resistance and Strong Adhesion.

Nanopapers containing cellulose nanofibrils (CNFs) are an emerging and sustainable class of high performance materials. The diversification and improvement of the mechanical and functional property space critically depend on integration of CNFs with rationally designed, tailor-made polymers following bioinspired nanocomposite designs. Here we combine for the first time CNFs with colloidal dispersions of vitrimer nanoparticles (VP) into mechanically coherent nanopaper materials. Vitrimers are permanently cross-linked polymer networks that undergo temperature-induced bond shuffling through an associative mechanism and which allow welding and reshaping on the macroscale. The choice of low glass transition, hydrophobic vitrimers derived from fatty acids and polydimethylsiloxane (PDMS), and achieving dynamic reshuffling of cross-links through transesterification reactions enables excellent compatibility and covalent attachment onto the CNF surfaces. Moreover, the resulting films are ductile, stretchable and offer high water resistance. The success of imparting the vitrimeric polymeric behavior into the nanocomposite, as well as the curing mechanism of the vitrimer, is highlighted through thorough analysis of structural and mechanical properties. The dynamic exchange chemistry of the vitrimers enables efficient welding of two nanocomposite parts as characterized by good bonding strength during single lap shear tests. In the future, we expect that the dynamic character of vitrimers becomes a promising option for the design of mechanically adaptive bioinspired nanocomposites and for shaping and reshaping such materials.

Visible-Light Emulsion Photopolymerization of Styrene.

The photopolymerization of styrene in emulsion is achieved in a conventional double-wall reactor equipped with a LED ribbon coiled around the external glass wall. Styrene mixed to acridine orange is added to the water phase containing sodium dodecyl sulfate, a water-soluble N-heterocyclic carbene-borane and disulfide, and irradiated. Highly stable latexes are obtained, with particles up to a diameter of 300 nm. The ability to reach such large particle sizes via a photochemical process in a dispersed medium is due to the use of visible light: the photons in the visible range are less scattered by larger objects and thus penetrate and initiate better the polymerizations. They are also greener and cheaper to produce via LEDs, and much safer than UVs. The method presented does not require any specific glassware; it works at lower temperature and delivers larger particles compared to thermal processes at similar solids contents and surfactant concentrations.

Investigation of the Adsorption of Amphipathic macroRAFT Agents onto Montmorillonite Clay.

Recently, there has been significant interest in the use of the reversible addition-fragmentation chain-transfer (RAFT) technique to generate a variety of organic/inorganic colloidal composite particles in aqueous dispersed media using the so-called macroRAFT-assisted encapsulating emulsion polymerization (REEP) strategy. In this process, special attention should be paid to the adsorption of the macromolecular RAFT (macroRAFT) agent onto the inorganic particles, as it determines the final particle morphology and can also influence latex stability. In this work, different amphipathic macroRAFT agents were synthesized by RAFT, and their adsorption onto commercial Montmorillonite clay Cloisite Na+ (MMT) was studied by means of adsorption isotherms. Three types of macroRAFT agents were considered: a nonionic one based on poly(ethylene glycol) methyl ether acrylate (PEGA) and n-butyl acrylate (BA), anionic ones, including a block copolymer and random copolymers, based on acrylic acid (AA), BA and PEGA, and cationic ones based on 2-(dimethylamino)ethyl methacrylate (DMAEMA), BA and PEGA. Six adsorption isotherm models (Langmuir, Freundlich, Tempkin, Redlich-Peterson, Sips, and Brunauer-Emmett-Teller) were adjusted to the experimental isotherms. The nonionic macroRAFT agent formed a monolayer on the clay surface with a maximum adsorption capacity of 400 mg g-1 at pH 8, as determined from the Sips adsorption model. Adsorption of the AA-based macroRAFT agents onto MMT was moderate at alkaline pH due to electrostatic repulsions, but increased with decreasing pH. The DMAEMA-based macroRAFT agents displayed a much stronger interaction with the oppositely charged MMT surface at acidic pH due to electrostatic interactions, and the concentration of adsorbed macroRAFT agent reached values as high as 800 mg g-1. The BET model fitted the experimental data relatively well indicating multilayer adsorption promoted by the presence of the hydrophobic BA units. In addition, the cationic macroRAFT agents afforded stable MMT/macroRAFT agent complexes as evaluated by dynamic light scattering and zeta potential analyses.

Design of latex-layered double hydroxide composites by tuning the aggregation in suspensions.

Colloidal stability of polymeric latex particles was studied in the presence of oppositely charged layered double hydroxide (LDH) platelets of different interlayer anions. Adsorption of the LDH particles led to charge neutralization and to overcharging of the latex at appropriate concentrations. Mixing stable colloidal suspensions of individual particles results in rapid aggregation once the LDH adsorption neutralizes the negative charges of the polymer spheres, while stable suspensions were observed at high and low LDH doses. The governing interparticle interactions included repulsive electrical double layer forces as well as van der Waals and patch-charge attractions, whose strength depended on the amount of LDH particles adsorbed on the latex surface. The type of the LDH interlayer anions did not affect the colloidal stability of the samples. Structural investigation of the obtained latex-LDH composites revealed that the polymer spheres were completely coated with the inorganic platelets once their concentration was sufficiently high. These results are especially important for designing synthetic routes for hybrid systems in suspensions, where stable colloids are required for uniform film-formation and for the homogeneous distribution of the inorganic filler within the composite materials.

Erratum: Dynamic Stratification in Drying Films of Colloidal Mixtures [Phys. Rev. Lett. 116, 118301 (2016)].

This corrects the article DOI: 10.1103/PhysRevLett.116.118301.

Publisher's Note: Dynamic Stratification in Drying Films of Colloidal Mixtures [Phys. Rev. Lett. 116, 118301 (2016)].

This corrects the article DOI: 10.1103/PhysRevLett.116.118301.

Dynamic Stratification in Drying Films of Colloidal Mixtures.

In simulations and experiments, we study the drying of films containing mixtures of large and small colloidal particles in water. During drying, the mixture stratifies into a layer of the larger particles at the bottom with a layer of the smaller particles on top. We developed a model to show that a gradient in osmotic pressure, which develops dynamically during drying, is responsible for the segregation mechanism behind stratification.

Partitioning of Laponite Clay Platelets in Pickering Emulsion Polymerization.

Partitioning of laponite disklike clay platelets between polymer particles and bulk aqueous phase was investigated in Pickering surfactant-free emulsion polymerization of styrene. Adsorption of laponite clay platelets plays an important role in the stabilization of this system, influencing the particle size and the number of particles, and, hence, the reaction rate. Adsorption isotherms show that, while the laponite clay platelets are almost fully exfoliated in water, they form multilayers on the surface of the polymer particles by the end of polymerization, as confirmed by transmission electron microscopy (TEM). This observation is supported by quartz crystal microbalance, conductivity, and TEM measurements, which reveal interactions between the clay and polystyrene, as a function of the ionic strength. The strong adsorption of clay platelets leaves a low residual concentration in the aqueous phase that cannot cause further nucleation of polymer particles, as demonstrated during seeded emulsion polymerization experiments in the presence of a high excess of clay. A Brunauer-Emmett-Teller (BET)-type model for laponite adsorption on polystyrene particles matches the adsorption isotherms.

Investigation of Four Different Laponite Clays as Stabilizers in Pickering Emulsion Polymerization.

Clay-armored polymer particles were prepared by emulsion polymerization in the presence of Laponite platelets that adsorb at the surface of latex particles and act as stabilizers during the course of the polymerization. While Laponite RDS clay platelets are most often used, the choice of the type of clay still remains an open issue that is addressed in the present article. Four different grades of Laponite were investigated as stabilizers in the emulsion polymerization of styrene. First, the adsorption isotherms of the clays, on preformed polystyrene particles, were determined by ICP-AES analysis of the residual clay in the aqueous phase. Adsorption of clay depended on the type of clay at low concentrations corresponding to adsorption as a monolayer. Adsorption of clay particles as multilayers was observed for all the grades above a certain concentration under the considered ionic strength (mainly due to the initiator ionic species). The stabilization efficiency of these clays was investigated during the polymerization reaction (free of any other stabilizer). The clays did not have the same effect on stabilization, which was related to differences in their compositions and in their adsorption isotherms. The different grades led to different polymer particles sizes and therefore to different polymerization reaction rates. Laponite RDS and S482 gave similar results, ensuring the best stabilization efficiency and the fastest reaction rate; the number of particles increased as the clay concentration increased. Stabilization with Laponite XLS gave the same particles size and number as the latter two clays at low clay concentrations, but it reached an upper limit in the number of nucleated polymer particles at higher concentrations indicating a decrease of stabilization efficiency at high concentrations. Laponite JS did not ensure a sufficient stability of the polymer particles, as the polymerization results were comparable to a stabilizer-free polymerization system.

Temperature Response of Rhodamine B-Doped Latex Particles. From Solution to Single Particles.

Nanoparticle-based temperature imaging is an emerging field of advanced applications. Herein, the sensitivity of the fluorescence of rhodamine B-doped latex nanoparticles toward temperature is described. Submicrometer size latex particles were prepared by a surfactant-free emulsion polymerization method that allowed a simple and inexpensive way to incorporate rhodamine B into the nanoparticles. Also, rhodamine B-coated latex nanoparticles dispersed in water were prepared in order to address the effect of the dye location in the nanoparticles on their temperature dependence. A better linearity of the temperature dependence emission of the rhodamine B-embedded latex particles, as compared to that of free rhodamine B dyes or rhodamine B-coated latex particles, is observed. Temperature-dependent fluorescence measurements by fluorescent confocal microscopy on individual rhodamine B-embedded latex particles were found similar to those obtained for fluorescent latex nanoparticles in solution, indicating that these nanoparticles could be good candidates to probe thermal processes as nanothermometers.

Effect of MacroRAFT Copolymer Adsorption on the Colloidal Stability of Layered Double Hydroxide Nanoparticles.

The colloidal behavior of layered double hydroxide nanoparticles containing Mg(2+) and Al(3+) ions as intralayer cations and nitrates as counterions (MgAl-NO3-LDH) was studied in the presence of a short statistical copolymer of acrylic acid (AA) and butyl acrylate (BA) terminated with 4-cyano-4-thiothiopropylsulfanyl pentanoic acid (CTPPA) (P(AA7.5-stat-BA7.5)-CTPPA) synthesized by reversible addition-fragmentation chain-transfer (RAFT) polymerization. Surface charge properties and aggregation of the particles were investigated by electrophoresis and dynamic light scattering (DLS), respectively. The negatively charged P(AA7.5-stat-BA7.5)-CTPPA adsorbed strongly on the oppositely charged particles, leading to charge neutralization at the isoelectric point (IEP) and charge reversal at higher copolymer concentrations. The dispersions were unstable, i.e., fast aggregation of the MgAl-NO3-LDH occurred near the IEP while high stability was achieved at higher P(AA7.5-stat-BA7.5)-CTPPA concentrations. Atomic force (AFM) and transmission electron (TEM) microscopy imaging revealed that the platelets preferentially adopted a face-to-face orientation in the aggregates. While the stability of the bare particles was very sensitive to ionic strength, the P(AA7.5-stat-BA7.5)-CTPPA copolymer-coated particles were extremely stable even at high salt levels. Accordingly, the limited colloidal stability of bare MgAl-NO3-LDH dispersions was significantly improved by adding an appropriate amount of P(AA7.5-stat-BA7.5)-CTPPA to the suspension.

Multicolour optical coding from a series of luminescent lanthanide complexes with a unique antenna.

The bis-tetrazolate-pyridine ligand H(2)pytz sensitises efficiently the visible and/or near-IR luminescence emission of ten lanthanide cations (Pr, Nd, Sm, Eu, Tb, Dy, Ho, Er, Tm, Yb). The Ln(III) complexes present sizeable quantum yields in both domains with a single excitation source. The wide range of possible colour combinations in water, organic solvents and the solid state makes the complexes very attractive for labelling and encoding.

Synthesis and site-specific functionalization of tetravalent, hexavalent, and dodecavalent silica particles.

Different shapes: Tetravalent, hexavalent, and dodecavalent silica particles were obtained by the growth of the silica core of binary tetrapods, hexapods, and dodecapods, respectively. The surface of the multivalent particles can be regioselectively functionalized, thereby leading to particles with anisotropic geometry and chemistry.

Stabilization of miniemulsion droplets by cerium oxide nanoparticles: a step toward the elaboration of armored composite latexes.

Stable methyl methacrylate (MMA) miniemulsions were successfully prepared using for the first time cerium oxide (CeO(2)) nanoparticles as solid stabilizers in the absence of any molecular surfactant. The interaction between MMA droplets and CeO(2) nanoparticles was induced by the use of methacrylic acid (MAA) as a comonomer. Both MAA and CeO(2) contents played a key role on the diameter and the stability of the droplets formed during the emulsification step. Cryo-transmission electron microscopy (TEM) images of the suspensions formed with 35 wt % of CeO(2) showed the presence of polydisperse 50-150 nm spherical droplets. More surprisingly, some nonspherical (likely discoidal) objects that could be the result of the sonication step were also observed. The subsequent polymerization of these Pickering miniemulsion droplets led to the formation of composite PMMA latex particles armored with CeO(2). In all cases, the conversion was limited to ca. 85%, concomitant with a loss of stability of the latex for CeO(2) contents lower than 35 wt %. This stability issues were likely related to the screening of the cationic charges present on CeO(2) nanoparticles upon polymerization. TEM images showed mostly spherical particles with a diameter ranging from 100 to 400 nm and homogeneously covered with CeO(2). Besides, for particles typically larger than 200 nm, a buckled morphology was observed supporting the presence of residual monomer at the end of the polymerization and consistent with the limited conversion. The versatility of these systems was further demonstrated using 35 wt % of CeO(2) and replacing MMA by n-butyl acrylate (BA) either alone or in combination with MMA. Stable monomer emulsions were always obtained, with the droplet size increasing with the hydrophobicity of the oil phase, pointing out the key influence of the wettability of the solid stabilizer. The polymerization of Pickering miniemulsion stabilized by CeO(2) nanoparticles proved to be an efficient strategy to form armored composite latex particles which may find applications in coating technology.

Spheres growing on a sphere: a model to predict the morphology yields of colloidal molecules obtained through a heterogeneous nucleation route.

Through the heterogeneous nucleation of polymer nodules on a surface-modified silica particle, the high-yield achievement of hybrid colloidal molecules with a well-controlled multipod-like morphology was recently demonstrated. However, as the formation mechanism of these colloidal molecules has not been completely understood yet, some opportunities remain to reduce the tedious empirical process needed to optimize the chemical recipes. In this work, we propose a model to help understand the formation mechanism of almost pure suspensions of well-defined colloidal molecules. The outcomes of the model allow proposing probable nucleation growth scenario able to explain the experimental results. Such a model should make easier the determination of the optimal recipe parameters for a targeted morphology. The reasonably good agreements between the model and the experimental results show that the most important processes have been captured. It is thus a first step toward the rational design of large quantities of chemically prepared colloidal molecules.

Carbon Quantum Dot-Catalyzed, Highly Efficient Miniemulsion Atom Transfer Radical Polymerization Induced by Visible Light.

Owing to the benefits of using natural or artificial light sources as a stimulus, photoinduced reversible-deactivation radical polymerization (photoRDRP) techniques have been recognized to be a powerful "green" platform for the preparation of well-defined polymers. However, the development of highly efficient visible light-induced photoRDRP processes in aqueous dispersed media remains a challenge due to light scattering and refraction by monomer droplets or colloidal particles. In this work, an efficient green photocatalyst, carbon quantum dots (CQDs), was introduced to visible light-mediated miniemulsion atom transfer radical polymerization (ATRP), leading to highly efficient polymerizations with reaction rates (>80% monomer conversion within 1 h) much higher than in previous studies. This heterogeneous photocatalytic system is presumed to involve three catalytic cycles in (i) the aqueous phase, (ii) the oil-water interface, and (iii) the monomer droplets. The effect of different polymerization parameters on the polymerization reaction was investigated, including the amounts of surfactant and CQDs, CuBr2 dosage, and solid content. Excellent temporal control of the polymerization was illustrated by "ON/OFF" polymerizations, and natural sunlight was also used as an energy source. This novel CQDs-catalyzed miniemulsion photoATRP process may be easily extended to other aqueous dispersion RDRP systems. As an extension of our previous work (J. Am. Chem. Soc. 2022, 144 (22), 9817-9826) we also developed a "one-pot" method for the rapid preparation of heterogeneous hydrogels.