Possibilities for Optimization of Industrial Alkaline Steeping of Wood-Based Cellulose Fibers.

Steeping of cellulosic materials in aqueous solution of NaOH is a common pre-treatment in several industrial processes for production of cellulose-based products, including viscose fibers. This study investigated whether the span of commonly applied process settings has the potential for process optimization regarding purity, yield, and degree of transformation to alkali cellulose. A hardwood kraft dissolving pulp was extracted with 17-20 wt% aq. NaOH at 40-50 °C. The regenerated residue of the pulp was characterized regarding its chemical composition, molecular structure, and cellulose conformation. Yield was shown to be favored primarily by low temperature and secondly by high alkali concentration. Purity of xylan developed inversely. Both purity of xylan and yield varied over the applied span of settings to an extent which makes case-adapted process optimization meaningful. Decreasing the steeping temperature by 2 °C increased xylan content in the residue with 0.13%-units over the whole span of applied alkali concentrations, while yield increased by 0.15%-units when extracting with 17 wt% aq. NaOH, and by 0.20%-units when extracting with 20 wt%. Moreover, the yield-favoring conditions resulted in a narrower molecular weight distribution. The degree of transformation via alkali cellulose to cellulose II, as determined with Raman spectroscopy, was found to be high at all extraction settings applied.

Adsorption of arabinoxylan on cellulosic surfaces: influence of degree of substitution and substitution pattern on adsorption characteristics.

This study presents results that show that the fine structure of arabinoxylan affects its interaction with cellulosic surfaces, an important understanding when designing and evaluating properties of xylan-cellulose-based materials. Arabinoxylan samples, with well-defined structures, were prepared from a wheat flour arabinoxylan with targeted enzymatic hydrolysis. Turbidity measurements and analyses using NMR diffusometry showed that the solubility and the hydrodynamic properties of arabinoxylan are determined not only by the degree of substitution but also by the substitution pattern. On the basis of results obtained from adsorption experiments on microcrystalline cellulose particles and on cellulosic model surfaces investigated with quartz crystal microbalance with dissipation monitoring, it was also found that arabinoxylan adsorbs irreversibly on cellulosic surfaces and that the adsorption characteristics, as well as the properties of the adsorbed layer, are controlled by the fine structure of the xylan molecule.

Acid hydrolysis of cellulosic fibres: Comparison of bleached kraft pulp, dissolving pulps and cotton textile cellulose.

The behaviour of different cellulosic fibres during acid hydrolysis has been investigated and the levelling-off degree of polymerisation (LODP) has been determined. The study included a bleached kraft pulp (both never-dried and once-dried) and two dissolving pulps (once-dried). Additionally, cotton cellulose from new cotton sheets and sheets discarded after long-time use was studied. Experimental results from the investigation, together with results found in literature, imply that ultrastructural differences between different fibres affect their susceptibility towards acid hydrolysis. Drying of a bleached kraft pulp was found to enhance the rate of acid hydrolysis and also result in a decrease in LODP. This implies that the susceptibility of cellulosic fibres towards acid hydrolysis is affected by drying-induced stresses in the cellulose chains. In cotton cellulose, it was found that use and laundering gave a substantial loss in the degree of polymerisation (DP), but that the LODP was only marginally affected.

CP/MAS ¹³C NMR study of pulp hornification using nanocrystalline cellulose as a model system.

The hornification process of paper pulp was investigated using solid-state (13)C NMR spectroscopy. Nanocrystalline cellulose was used to serve as a model system of the crystalline parts of the fibrils in pulp fibers. Characterization of the nanocrystalline cellulose dimensions was carried out using scanning electron microscopy. The samples were treated by drying and wetting cycles prior to NMR analysis where the hornification phenomenon was recorded by spectral changes of the cellulose C-4 carbon signals. An increase of the crystalline signal and a decrease of the signals corresponding to the accessible amorphous domains were found for both paper pulp and nanocrystalline cellulose. These spectral changes grew stronger with repeating drying and wetting cycles. The results show that cellulose co-crystallization contribute to hornification. Another conclusion is that the surfaces of higher hydrophobicity in cellulose fibrils have an increased preference for aggregation.