Monitoring of CO Binding Sites on Stepped Pt Single Crystal Electrodes in Alkaline Solutions by in Situ FTIR Spectroscopy.

The site geometry preference of CO binding on stepped Pt single crystals in alkaline solution was investigated by in situ FTIR spectroscopy. The surfaces of the Pt single crystals consisted of different width (111) terraces, interrupted by (110) or (100) monatomic steps. Experiments carried out with CO adsorbed exclusively on the top of the steps revealed that only linearly bonded CO formed on the (110) steps, while two CO binding geometries (linear and bridge) were observed on the (100) steps. On one hand, for CO adsorbed only on the steps, the positions of the bands corresponding to linearly bonded CO were similar, regardless of the density of steps, suggesting the existence of an interaction between COads only along the line of the steps. On the other hand, for full CO coverage, the CO stretching frequencies and the geometry of bound CO were sensitive to the width of the (111) terraces and the step orientations. Consequently, the CO binding sites favored linearly bonded CO for surfaces consisting of shorter (111) terraces and (110) steps. Bridge-bonded CO was favored on surfaces consisting of shorter (111) terraces interrupted by (100) steps. In order to understand the origin of the preference of CO binding sites, the results were compared to the corresponding behavior in acid media, which revealed that, in addition to the effect inherent to the Pt surface, the charge on the metal side in an aqueous environment should be taken into consideration. The analysis suggested that the CO adlayers formed at full coverage in acidic and alkaline media had different structures. On the other hand, the structure of the layer of CO adsorbed only at the steps was independent of pH.

ZnO nanowire-based fluorometric enzymatic assays for lactate and cholesterol.

A rapid fluorometric method is described for the determination of lactate and cholesterol by using ZnO nanowires (ZnO NWs). The assay is based on the detection of the hydrogen peroxide generated during the enzymatic reactions of the oxidation of lactate or cholesterol. Taking advantage of the electrostatic interactions between the enzymes and the ZnO NWs, two bioconjugates were prepared by mixing the nanomaterial and the enzymes, viz. lactate oxidase (LOx) or cholesterol oxidase (ChOx). The enzymatically generated hydrogen peroxide quenches the fluorescence of the ZnO NWs, which have emission peaks at 384 nm and at 520 nm under 330 nm photoexcitation. H2O2 quenches the 520 nm band more strongly. Response is linear up to 1.9 µM lactate concentration, and up to 1.1 µM cholesterol concentration. Relative standard deviation was found to be 5%. The detection limits for lactate and cholesterol are 0.54 and 0.24 µM, respectively. Graphical abstractSchematic representation of fluorescence assay based on ZnO nanowires photoluminiscence for lactate and colesterol detection.

Glycerol electrooxidation on Pd modified Au surfaces in alkaline media: Effect of the deposition method.

The catalytic effect of Pd on gold electrodes for glycerol oxidation is evaluated for Pd-Au surfaces prepared using three different methods: irreversible adsorption of palladium by a simple immersion of a gold electrode in palladium solution, the deposition of palladium on the gold substrate by a step potential from 1 to 0.75 V, and the forced deposition of palladium on the gold electrode with the help of a reducing hydrogen atmosphere. Voltammetry has been used for the electrochemical characterization of the Pd-Au deposits and to determine its reactivity towards glycerol oxidation, whereas FTIR experiments have allowed detecting adsorbed species and products formed during the oxidation reaction. Pd-Au surfaces prepared by irreversible adsorption are the electrodes that show the highest activity for the glycerol complete oxidation to carbonate, whereas Pd-Au surfaces made by the step potential are the catalyst that exhibits the highest rate for the formation and adsorption CO before carbonate production, poisoning the surface and diminishing their electrocatalytic properties. In addition to carbonate, glycerate, glycolate, and formate are detected as oxidation products. The integrated bands of the spectra are used to give quantitative information for comparing the product distribution of the different Pd-Au deposits prepared.

Mobility and Oxidation of Adsorbed CO on Shape-Controlled Pt Nanoparticles in Acidic Medium.

The knowledge about how CO occupies and detaches from specific surface sites on well-structured Pt surfaces provides outstanding information on both dynamics/mobility of COads and oxidation of this molecule under electrochemical conditions. This work reports how the potentiostatic growth of different coverage CO adlayers evolves with time on both cubic and octahedral Pt nanoparticles in acidic medium. Data suggest that during the growth of the CO adlayer, COads molecules slightly shift toward low coordination sites only on octahedral Pt nanoparticles, so that these undercoordinated sites are the first filled on octahedral Pt nanoparticles. Conversely, on cubic Pt nanoparticles, adsorbed CO behaves as an immobile species, and low coordinated sites as well as (100) terraces are apparently filled uniformly and simultaneously. However, once the adlayer is complete, irrespectively of whether the CO is oxidized in a single step or in a sequence of different potential steps, results suggest that COads behaves as an immobile species during its oxidation on both octahedral and cubic Pt nanoparticles.

Ethanol oxidation on Pt single-crystal electrodes: surface-structure effects in alkaline medium.

Ethanol oxidation in 0.1 M NaOH on single-crystal electrodes has been studied using electrochemical and FTIR techniques. The results show that the activity order is the opposite of that found in acidic solutions. The Pt(111) electrode displays the highest currents and also the highest onset potential of all the electrodes. The onset potential for the oxidation of ethanol is linked to the adsorption of OH on the electrode surface. However, small (or even negligible) amounts of CO(ads) and carbonate are detected by FTIR, which implies that cleavage of the C-C bond is not favored in this medium. The activity of the electrodes diminishes quickly upon cycling. The diminution of the activity is proportional to the measured currents and is linked to the formation and polymerization of acetaldehyde, which adsorbs onto the electrode surface and prevents further oxidation.

Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity.

Thallium modified shape-controlled Pt nanoparticles were prepared and their electrocatalytic activity towards formic acid electrooxidation was evaluated in 0.5 M sulfuric acid. The electrochemical and in situ FTIR spectroscopic results show a remarkable improvement in the electrocatalytic activity, especially in the low potential region (around 0.1-0.2 V vs. RHE). Cubic Pt nanoparticles modified with Tl were found to be more active than the octahedral Pt ones in the entire range of Tl coverages and potential windows. In situ FTIR spectra indicate that the promotional effect produced by Tl results in the inhibition of the poisoning step leading to COads, thus improving the onset potential for the complete formic acid oxidation to CO2. Chronoamperometric experiments were also performed at 0.2 V to evaluate the stability of the electrocatalysts at constant potential. Finally, experiments with different concentrations of formic acid (0.05-1 M) were also carried out. In all cases, Tl-modified cubic Pt nanoparticles result to be the most active. All these facts reinforce the importance of controlling the surface structure of the electrocatalysts to optimize their electrocatalytic properties.