Removal of polyvinylidene fluoride binder and other organics for enhancing the leaching efficiency of lithium and cobalt from black mass.

The agglomeration and encapsulation of recoverable materials of interest (e.g. metals and graphite) as a result of the presence of polyvinylidene fluoride (PVDF) in spent lithium-ion batteries (LIBs) with mixed chemistries (black mass) lower the extraction efficiency of metals. In this study, organic solvents and alkaline solutions were used as non-toxic reagents to investigate the removal of a PVDF binder from a black mass. The results demonstrated that 33.1%, 31.4%, and 31.4% of the PVDF were removed using dimethylformamide (DMF), dimethylacetamide (DMAc), and dimethyl sulfoxide (DMSO) at 150, 160, and 180 °C, respectively. Under these conditions, the peel-off efficiencies for DMF, DMAc, and DMSO were 92.9%, 85.3%, and approximately 92.9%, respectively. Using tetrabutylammonium bromide (TBAB) as a catalyst and 5 M sodium hydroxide (NaOH) at room temperature (RT- 21 °C-23 °C), 50.3% of PVDF and other organic compounds were eliminated. The removal efficiency was enhanced to approximately 60.5% when the temperature was raised to 80 °C using NaOH. Using 5 M potassium hydroxide at RT in a TBAB-containing solution, ca. 32.8% removal efficiency was obtained; raising the temperature to 80 °C further enhanced the removal efficiency to almost 52.7%. The peel-off efficiency was 100% for both alkaline solutions. Lithium extraction increased from 47.2% to 78.7% following treatment with DMSO and to 90.1% following treatment with NaOH via leaching black mass (2 M sulfuric acid, solid-to-liquid ratio (S/L): 100 g L-1 at 50 °C, for 1 h without a reducing agent) before and after removal of the PVDF binder. Cobalt's recovery went from 28.5% to 61.3% with DMSO treatment to 74.4% with NaOH treatment.

The inside-out supercapacitor: induced charge storage in reduced graphene oxide.

Iontronic circuits are built using components which are analogous to those used in electronic circuits, however they involve the movement of ions in an electrolyte rather than electrons in a metal or semiconductor. Developments in these circuits' performance have led to applications in biological sensing, interfacing and drug delivery. While transistors, diodes and elementary logic circuits have been demonstrated for ionic circuits if more complex circuits are to be realized, the precident set by electrical circuits suggests that a component which is analogous to an electrical capacitor is required. Herein, an ionic supercapacitor is reported, our experiments show that charge may be stored in a conductive porous reduced graphene oxide film that is contacted by two isolated aqueous solutions and that this concept extends to an arbitrary polarizable sample. Parametric studies indicate that the conductivity and porosity of this film play important roles in the resultant device's performance. This ionic capacitor has a specific capacitance of 8.6 F cm-3 at 1 mV s-1 and demonstrates the ability to filter and smooth signals in an electrolyte at a variety of low frequencies. The device has the same interfaces as a supercapacitor but their arrangement is changed, hence the name inside-out supercapacitor.

Magnesium Implants: Prospects and Challenges.

Owing to their suitable mechanical property and biocompatibility as well as the technological possibility of controlling their high corrosion rates, magnesium and its alloys have attracted significant attention as temporary bio-implants. Though the ability of magnesium to harmlessly biodegrade and its inherent biocompatibility make magnesium alloys a suitable choice for a temporary implant, their high corrosion rates limit their practical application, as the implants can potentially corrode away even before the healing process has completed. Different approaches, such as alloying, surface modification, and conversion coatings, have been explored to improve the corrosion resistance of various magnesium alloys. However, the corrosion behavior of magnesium implants with and without a surface modification has been generally investigated under in-vitro conditions, and studies under in-vivo conditions are limited, which has contributed to the lack of translation of magnesium implants in practical applications. This paper comprehensively reviews the prospects of magnesium alloy implants and the current challenges due to their rapid degradation in a physiological environment. This paper also provides a comprehensive review of the corrosion mitigation measures for these temporary implants.