Study on the Preparation of Estrone Molecularly Imprinted Polymers and Their Application in a Quartz Crystal Microbalance Sensor via a Computer-Assisted Design.

Computer simulations are widely used for the selection of conditions for the synthesis of molecularly imprinted polymers and can rapidly reduce the experimental cycle time and save labor and materials. In this paper, estrone molecularly imprinted polymers (E1-MIPs) are designed at the M062X/6-311+G(d,p) level with itaconic acid (IA) as the functional monomer. The imprinted molar ratio between E1 and IA was optimized, cross-linkers and solvents were screened, and the nature of interactions between E1 and IA was explored. The simulated results showed that pentaerythritol triacrylate was the best cross-linker. Meanwhile, when the imprinted molar ratio between E1 and IA was 1:4, the E1-IA complex had the largest amount of hydrogen bonds, the lowest binding energy, and the strongest stability. Using the simulation results as guidance, the E1-MIPs were prepared to modify the electrons of a quartz crystal microbalance (QCM) sensor. The experimental studies showed that the E1-MIPs-QCM sensor had the highest adsorption capacity to E1 in comparison with their analogues, and the lowest detection value of the sensor was 16.00 µg/L. The computer simulations and experimental studies could provide guidance for synthesize novel E1-MIPs materials. It also could provide important references and directions for the application of E1-MIPs.

The Optimal Design of the Press Roller to Improve the Winding Molding Quality of Heat Insulation.

In the heat insulation winding molding process of solid rocket motors, the pressure applied by the press roller directly affects the quality of the winding molding. Insufficient pressure can result in poor bonding quality and may cause defects. This paper aims to provide an optimal design of the press roller to improve the winding molding quality of the heat insulation. The effect of the cylindrical press roller on the pressure distribution was analyzed using the elastic foundation model and a finite element (FE) model, which was assessed by Hertz theory. Subsequently, the press roller was optimized to an elliptical concave design. The effect of the radius of the elliptical concave press roller on the pressure distribution was analyzed. A comparison of the effect of the elliptical concave press roller and the cylindrical press roller on the pressure distribution was conducted using the FE model. The results show pressure uniformity is significantly improved when the elliptical concave press roller is employed on the mandrel with the smallest radius. Additionally, the elliptical concave press roller increases the pressure at the edge of the tape, which reduces the risk of lifted edges and, thereby, improves the winding molding quality of the heat insulation.

Characterization of SARS-CoV-2-specific humoral immunity and associated factors in the healthy population post-vaccination.

OBJECTIVES: To investigate factors that may influence humoral immunity post-vaccination with a COVID-19-inactivated vaccine (SC2IV). METHODS: A total of 1596 healthy individuals from the Seventh Affiliated Hospital, Sun Yat-sen University (1217) and Shenzhen Baotian Hospital (379) were enrolled in this study among which 694 and 218 participants were vaccinated with two-dose SC2IV, respectively. Physical examination indices were recorded. The levels of neutralizing antibody (NA), Spike IgG, receptor-binding domain (RBD) IgG, RBD IgG + IgM + IgA, and nucleocapsid IgG of SARS-CoV-2 were measured by a non-virus ELISA kit. Multiple statistical analyses were carried out to identify factors that influence humoral immunity post-vaccination. RESULTS: The two-dosage vaccination could induce NA in more than 90 % of recipients. The NA has the strongest correlation with anti-RBD IgG. Age is the most important independent index that affects the NA level, while basophil count, creatine kinase-MB, mean corpuscular hemoglobin, the ratio of albumin to urine creatinine, and thyroglobulin antibody have relatively minor contributions. Indices that affect the NA level were different between males and females. Antibodies targeting other epitopes of SARS-CoV-2 were detected in recipients without anti-RBD. CONCLUSIONS: The factors identified in association with the NA level post-vaccination may help to evaluate the protective effect, risk of re-infection, the severity of symptoms, and prognosis for vaccine recipients in clinical.

Mycotoxin Zearalenone Attenuates Innate Immune Responses and Suppresses NLRP3 Inflammasome Activation in LPS-Activated Macrophages.

Zearalenone (ZEA) is a mycotoxin that has several adverse effects on most mammalian species. However, the effects of ZEA on macrophage-mediated innate immunity during infection have not been examined. In the present study, bacterial lipopolysaccharides (LPS) were used to induce the activation of macrophages and evaluate the effects of ZEA on the inflammatory responses and inflammation-associated signaling pathways. The experimental results indicated that ZEA suppressed LPS-activated inflammatory responses by macrophages including attenuating the production of proinflammatory mediators (nitric oxide (NO) and prostaglandin E2 (PGE2)), decreased the secretion of proinflammatory cytokines (tumor necrosis factor (TNF)-α, interleukin (IL)-1ß and IL-6), inhibited the activation of c-Jun amino-terminal kinase (JNK), p38 and nuclear factor-κB (NF-κB) signaling pathways, and repressed the nucleotide-binding and oligomerization domain (NOD)-, leucine-rich repeat (LRR)- and pyrin domain-containing protein 3 (NLRP3) inflammasome activation. These results indicated that mycotoxin ZEA attenuates macrophage-mediated innate immunity upon LPS stimulation, suggesting that the intake of mycotoxin ZEA-contaminated food might result in decreasing innate immunity, which has a higher risk of adverse effects during infection.