Enhanced supercapacitor performance of porous carbon through tuning maceral composition proportion of coal.

Porous carbons (PCs) have been widely investigated as electrode materials for supercapacitors. However, during the preparation process, intense pore formation reactions result in an amorphous carbon structure, which limits the rate performance of the electrode material. Herein, coal is chosen as a carbon source and making use of different reaction characteristics of vitrinite and inertinite with a KOH activator, an interconnected porous structure carbon material with an abundant graphite microcrystalline structure is obtained; the organic relationships between the ratio of vitrinite and inertinite, carbonization conditions, material structure and capacity performance were researched. At the ratio of vitrinite to inertinite of 1 : 2, the sample shows a specific surface area of 2507 m2 g-1 and its ID1/IG is 1.31, which is lower than that of raw coal (1.36). Due to the synergistic effect of the pore structure and graphite microcrystals, PC-900-40 exhibits an improved specific capacitance of 229.40 F g-1 at a current density of 1.0 A g-1, and even at a high current density of 10.0 A g-1 it delivers a specific capacitance of 170.04 F g-1. The PC-900-40//PC-900-40 symmetrical capacitor retains 96% of its initial capacitance after 20 000 cycles.

Rational selection of amorphous or crystalline V2O5 cathode for sodium-ion batteries.

Vanadium oxide (V2O5), as a potential positive electrode for sodium ion batteries (SIBs), has attracted considerable attention from researchers. Herein, amorphous and crystalline V2O5 cathodes on a graphite paper without a binder and conductive additives have been synthesized via facile anodic electrochemical deposition following different heat treatments. Both the amorphous V2O5 (a-V2O5) cathode and crystalline V2O5 (c-V2O5) cathode show good rate cycling performance and long cycling life. After five rate cycles, the reversible capacities of both the cathodes were almost unchanged at different current densities from 40 to 5120 mA g-1. Long cycling tests with 10 000 cycles were carried out and the two cathodes exhibit excellent cycling stability. The c-V2O5 cathode retains a high specific capacity of 54 mA h g-1 after 10 000 cycles at 2560 mA g-1 and can be charged within 80 s. Interestingly, the a-V2O5 cathode possesses higher reversible capacities than the c-V2O5 cathode at low current densities, whereas it is inversed at high current densities. The c-V2O5 cathode shows faster capacity recovery from 5120 to 40 mA g-1 than the a-V2O5 cathode. When discharged at 80 mA g-1 (long discharge time of 140 min) and charged at 640 mA g-1 (short charge time of 17 min), the a-V2O5 cathode shows a higher discharge capacity than its c-V2O5 counterpart. The different electrochemical performance of a-V2O5 and c-V2O5 cathodes during various electrochemical processes can provide a rational selection of amorphous or crystalline V2O5 cathode materials for SIBs in their practical applications to meet the variable requirements.

Magnetic Properties in Mn-Doped δ-MoN: A Systematic Density Functional Theory Study.

Due to the potential applications of transition metal nitrides in modern electronic and spintronic devices, we have systematically studied the magnetic properties of δ-MoN induced by the Mn dopant, with the goal of identifying the origin of magnetism and figuring out the magnetic coupling mechanism between the Mn dopants. Based on the density functional theory, one Mn atom doped at different Mo sites (2a and 6c in the International Tables) in the unit cell of δ-MoN was firstly studied. It was found that the Mn dopant located at the 2a or 6c site leads to significant spin splitting of the density of states, suggesting that the Mn doping induces magnetism in δ-MoN. The calculations were then extended to a 2 × 1 × 2 supercell, which contains two impurity Mn atoms. Detailed analysis reveals that the different couplings of the Mn-Mn pair cannot be simply attributed to the different Mn-Mn distances but are closely related to the electronic processes that take place in the segment (-N- or -N-Mo-N-) that connects two Mn dopants. The mechanisms responsible for the FM/AFM coupling of the Mn-Mn pairs are the superexchange and the p-d exchange mediated by the N atoms, and the d-d coupling between the host Mo atom and the Mn dopant.

S, O dual-doped porous carbon derived from activation of waste papers as electrodes for high performance lithium ion capacitors.

To circumvent the imbalances of electrochemical kinetics and charge-storage capacity between Li+ ion battery anodes and capacitive cathodes in lithium-ion capacitors (LICs), dual carbon based LICs are constructed and investigated extensively. Herein, S, O dual-doped 3D net-like porous carbon (S-NPC) is prepared using waste paper as the carbon source through a facile solvothermal treatment and chemical activation. Benefiting from the combination effect of the rich S,O-doping (about 2.1 at% for S, and 9.0 at% for O), high surface area (2262 m2 g-1) and interconnected porous network structure, the S-NPC-40 material exhibits excellent electrochemical performance as both cathode material and anode material for LICs. S, O doping not only increases the pseudocapacity but also improves the electronic conductivity, which is beneficial to reduce the mismatch between the two electrodes. The S-NPC-40//S-NPC-40 LIC delivers high energy densities of 176.1 and 77.8 W h kg-1 at power densities of 400 and 20 kW kg-1, respectively, as well as superior cycling stability with 82% capacitance retention after 20 000 cycles at 2 A g-1. This research provides an efficient method to convert waste paper to porous carbon electrode materials for high performance LIC devices.

Ionic liquid electrodeposition of strain-released Germanium nanowires as stable anodes for lithium ion batteries.

With the growing demand for portable and wearable electronic devices, it is imperative to develop high performance Li-ion batteries with long life times. Germanium-based materials have recently demonstrated excellent lithium-ion storage ability and are being considered as the most promising candidates for the anodes of lithium-ion batteries. Nevertheless, the practical implementation of Ge-based materials to Li-ion batteries is greatly hampered by the poor cycling ability that resulted from the huge volume variation during lithiation/delithiation processes. Herein, we develop a simple and efficient method for the preparation of Ge nanowires without catalyst nanoparticles and templates, using ionic liquid electrodeposition with subsequent annealing treatment. The Ge nanowire anode shows improved electrochemical performance compared with the Ge dense film anode. A capacity of ∼1200 mA h g-1 after 200 cycles at 0.1 C is obtained, with an initial coulombic efficiency of 81.3%. In addition, the Ge nanowire anode demonstrates superior rate capability with excellent capacity retention and stability (producing highly stable discharge capacities of about 620 mA h g-1 at 5 C). The improved electrochemical performance is the result of the enhanced electron migration and electron transport paths of the nanowires, and sufficient elasticity to buffer the volume expansion. This approach encompasses a low energy processing method where all the material is electrochemically active and binder free. The improved cycling stability and rate performance characteristics make these anodes highly attractive for the most demanding lithium-ion applications.

Preparation of Ge nanotube arrays from an ionic liquid for lithium ion battery anodes with improved cycling stability.

Ge nanotube array anodes are prepared by template-assisted electrodeposition from an ionic liquid to obtain superior cycling performance. They show remarkable cycling ability at 0.2 C, with a very high initial discharge capacity of 1641 mA h g(-1) and a charge capacity of 1260 mA h g(-1). After 250 cycles the capacity retention is 98% relative to that at the 50th cycle.