Supramolecular control of the structure and receptor properties of an amphiphilic hemicyanine chromoionophore monolayer at the air/water interface.

Designing sensors for toxic compounds such as mercury salts in aqueous solutions still remains one of the most pressing tasks of modern chemical research, since many existing systems do not show enough sensitivity and/or response. In this regard, the opportunities offered by supramolecular approaches can be used to improve both these characteristics by creating a new self-organized smart system. Herein, we show that barium cations, that according to the data of X-ray standing waves do not bind directly to the ionophore molecules in the monolayers at the air/water interface, could be used to efficiently preorganize such molecules to achieve supramolecular architecture. We demonstrate that such preorganization ensures both low analyte detection threshold and high fluorescent response. We reveal the interrelation of the monolayer structure and receptor characteristics of a sensory system and show that such cation-induced preorganization in Langmuir monolayers of a hemicyanine dithia-aza-crown-substituted chromoionophore inhibits the formation of non-fluorescent aggregates with low receptor function, and allows the quantitative detection of mercury cations using a ratiometric fluorometric approach.

Viscoll collagen solution as a novel bioink for direct 3D bioprinting.

Collagen is one of the most promising materials for 3D bioprinting because of its distinguished biocompatibility. Cell-laden constructs made of pure collagen with or without incorporated growth supplements support engineered constructs persistence in culture and are perfectly suitable for grafting. The limiting factor for direct 3D collagen printing was poor printability of collagen solutions, especially admixed with cells or tissue spheroids. In our study, we showed that concentrated solutions of native collagen branded Viscoll were effective as bioinks with high fidelity performance. Viscoll containing 20, 30, or 40 mg/ml collagen were used for direct extrusion 3D bioprinting to form scaffolds appropriate to support spatial arrangement of tissue spheroids into rigid patterns with resolution of 0.5 mm in details. Incorporated cells demonstrated sufficient viability. Associated rheological study showed that good printability of the collagen solutions correlates with their increased storage modulus value, notably exceeding the loss modulus value. The proper combination of these physical parameters could become technological criteria for manufacturing various collagen bioinks for 3D bioprinting.

Close-packed polybutylcarbosilane dendrimers of higher generations.

Variation of generation number strongly affects the type of ordering found for polybutylcarbosilane dendrimers: G5 dendrimers are liquid-like, G6 are cubic liquid crystals and G7/G8 are disordered close-packed. It was revealed that G6 dendrimers are highly likely to form Im3[combining macron]m lattice structures with the parameter a = 5.15 nm, and a domain size that exceeds 100 nm.

Planar and 3D fibrous polyaniline-based materials for memristive elements.

The memristive elements constructed using polymers - polyaniline (PANI) and polyethyleneoxide (PEO) - could be assembled on planar thin films or on 3D fibrous materials. Planar conductive PANI-based materials were made using the Langmuir-Schaefer (LS) method, and the 3D materials - using the electrospinning method which is a scalable technique. We have analyzed the influence of PANI molar mass, natures of solvent and subphase on the crystalline structure, thickness and conductivity of planar LS films, and the influence of PANI molar mass and the PANI-PEO ratio on the morphological and structural characteristics of 3D fibrous materials.

Fibroblasts and polymer composition are essential for bioengineering of airway epithelium on nonwoven scaffolds.

To make tissue engineering a truly effective tool, it is necessary to understand how the patterns of specific tissue development are modulated by and depend on the artificial environment. Even the most advanced approaches still do not fully meet the requirements of practical engineering of tracheobronchial epithelium. This study aimed to test the ability of the synthetic and natural nonwoven scaffolds to support the formation of morphological sound airway epithelium including the basement membrane (BM). We also sought to identify the potential role of fibroblasts in this process. Our results showed that nonwoven scaffolds are generally suitable for producing well-differentiated tracheobronchial epithelium (with cilia and goblet cells), while the structure and functionality of the equivalents appeared to be highly dependent on the composition of the scaffolds. Unlike natural scaffolds, synthetic ones supported the formation of the epithelium only when epithelial cells were cocultured with fibroblasts. Fibroblasts also appeared to be obligatory for basal lamina formation, regardless of the type of the nonwoven material used. However, even in the presence of fibroblasts, the synthetic scaffolds were unable to support the formation of the epithelium and of the BM (in particular, basal lamina) as effectively as the natural scaffolds did.

Effect of collagen denaturation degree on mechanical properties and biological activity of nanofibrous scaffolds.

Further progress in regenerative medicine and bioengineering highly depends on the development of 3D polymeric scaffolds with active biological properties. The most attention is paid to natural extracellular matrix components, primarily collagen. Herein, nonwoven nanofiber materials with various degrees of collagen denaturation and fiber diameters 250-500 nm were produced by electrospinning, stabilized by genipin, and characterized in detail. Collagen denaturation has been confirmed using DSC and FTIR analysis. The comparative study of collagen and gelatin nonwoven materials (NWM) revealed only minor differences in their biocompatibility with skin fibroblasts and keratinocytes in vitro. In long-term subcutaneous implantation study, the inflammation was less evident on collagen than on gelatin NWM. Remarkably, the pronounced calcification was revealed in the collagen NWM only. The results obtained can be useful in terms of improving the electrospinning technology of collagen from aqueous solutions, as well as emphasize the importance of long-term study to ensure proper implementation of the material, taking into account the ability of collagen to provoke calcification.

Nonwoven spidroin materials as scaffolds for ex vivo cultivation of aortic fragments and dorsal root ganglia.

Recombinant spidroins (RS; the analogues of silk proteins of spider's web) have multiple properties beneficial for bioengineering, including their suitability for electrospinning and thus, for production of materials with oriented fibers. This makes RS-based matrices potentially effective in stimulating regeneration of peripheral nerves. The restoration of injured nerves also depends on prompt regrowth of blood vessels. Therefore, prospective scaffold materials for neuro-regenerative therapy should positively affect both the nerves and the blood vessels. Currently, the experimental models suitable for culturing and quantitative assessment of the vascular and neuronal cells on the same material are lacking. Here, we assessed the suitability of electrospun RS-based matrices for cultivation of the mouse aorta and dorsal root ganglia (DRG) explants. We also quantified the effects of matrix topography upon both types of tissues. The RS-based materials have effectively supported aortic explants survival and sprouting. The cumulative length of endothelial sprouts on rS1/9-coated inserts was significantly higher as compared to type I collagen coatings, suggesting stimulatory effects on angiogenesis in vitro. In contrast to matrices with random fibers, on matrices with parallel fibers the migration of both smooth muscle and endothelial cells was highly oriented. Furthermore, alignment of RS fibers effectively directs the growth of axons and the migration of Schwann cells from DRGs. Thus, the electrospun RS matrices are highly suitable to culture both, the DRGs and aortic explants and to study the effects of matrix topography on cell migration. This model has a high potential for further endeavor into interactions of nerve and vascular cells and tissues.

Influence of γ-Radiation on Mechanical Stability to Cyclic Loads Tubular Elastic Matrix of the Aorta.

A significant drawback of the rigid synthetic vascular prostheses used in the clinic is the mechanical mismatch between the implant and the prosthetic vessel. When placing prostheses with radial elasticity, in which this deficiency is compensated, the integration of the graft occurs more favorably, so that signs of cell differentiation appear in the prosthesis capsule, which contributes to the restoration of vascular tone and the possibility of vasomotor reactions. Aortic prostheses fabricated by electrospinning from a blend of copolymers of vinylidene fluoride with hexafluoropropylene (VDF/HFP) had a biomechanical behavior comparable to the native aorta. In the present study, to ensure mechanical stability in the conditions of a living organism, the fabricated blood vessel prostheses (BVP) were cross-linked with γ-radiation. An optimal absorbed dose of 0.3 MGy was determined. The obtained samples were implanted into the infrarenal aorta of laboratory animals-Landrace pigs. Histological studies have shown that the connective capsule that forms around the prosthesis has signs of high tissue organization. This is evidenced by the cells of the fibroblast series located in layers oriented along and across the prosthesis, similar to the orientation of cells in a biological arterial vessel.

True Molecular Composites: Unusual Structure and Properties of PDMS-MQ Resin Blends.

Poly(dimethyl siloxane)-MQ rubber molecular composites are easy to prepare, as it does not require a heterophase mixing of ingredients. They are characterized by perfect homogeneity, so they are very promising as rubber materials with controllable functional characteristics. The manuscript reveals that MQ resin particles can significantly, more than by two orders of magnitude, enhance the mechanical properties of poly(dimethyl siloxane), and, as fillers, they are not inferior to aerosils. In the produced materials, MQ particles play a role of the molecular entanglements, so rubber molecular weight and MQ filler concentration are the parameters determining the structure and properties of such composites. Moreover, a need for a saturation of the reactive groups and minimization of the surface energy of MQ particles also determine the size and distribution of the filler at different filler rates. An unusual correlation of the concentration of MQ component and the interparticle spacing was revealed. Based on the extraordinary mechanical properties and structure features, a model of the structure poly(dimethyl siloxane)-rubber molecular composites and of its evolution in the process of stretching, was proposed.

Assembling of Metal-Polymer Nanocomposites in Irradiated Solutions of 1-Vinyl-1,2,4-triazole and Au(III) Ions: Features of Polymerization and Nanoparticles Formation.

Gold nanoparticles (AuNPs) stabilized with poly(1-vinyl-1,2,4-triazole) (PVT) have been synthesized via a one-pot manner in irradiated solutions of 1-vinyl-1,2,4-triazole (VT) and Au(III) ions. The transmission electron microscopy examinations have shown that the sizes of nanoparticles formed range from 1 to 11 nm and are affected by the ratio of VT to gold ions. To study the kinetics peculiarities of the VT polymerization and assembling of AuNPs, UV-Vis spectroscopy was used. The analysis of the data obtained reveals that an inhibition period, influenced by Au(III) concentration, is followed by the polymerization of a monomer. Importantly, the absorbed doses, corresponding to the onset of rapid polymerization, correlate with the doses at which the accelerated formation of AuNPs begins. The kinetics aspects, which could lead to such an effect, are discussed.

The Performance of Nonwoven PLLA Scaffolds of Different Thickness for Stem Cells Seeding and Implantation.

The 3D reconstruction of 100 µm- and 600 µm-thick fibrous poly-L/L-lactide scaffolds was performed by confocal laser scanning microscopy and supported by scanning electron microscopy and showed that the density of the fibers on the side adjacent to the electrode is higher, which can affect cell diffusion, while the pore size is generally the same. Bone marrow mesenchymal stem cells cultured in a 600 µm-thick scaffold formed colonies and produced conditions for cell differentiation. An in vitro study of stem cells after 7 days revealed that cell proliferation and hepatocyte growth factor release in the 600 µm-thick scaffold were higher than in the 100 µm-thick scaffold. An in vivo study of scaffolds with and without stem cells implanted subcutaneously onto the backs of recipient mice was carried out to test their biodegradation and biocompatibility over a 0-3-week period. The cells seeded onto the 600 µm-thick scaffold promoted significant neovascularization in vivo. After 3 weeks, a significant number of donor cells persisted only on the inside of the 600 µm-thick scaffold. Thus, the use of bulkier matrices allows to prolong the effect of secretion of growth factors by stem cells during implantation. These 600 µm-thick scaffolds could potentially be utilized to repair and regenerate injuries with stem cell co-culture for vascularization of implant.

Hybrid Polycarbosilane-Siloxane Dendrimers: Synthesis and Properties.

A series of carbosilane dendrimers of the 4th, 6th, and 7th generations with a terminal trimethylsilylsiloxane layer was synthesized. Theoretical models of these dendrimers were developed, and equilibrium dendrimer conformations obtained via molecular dynamics simulations were in a good agreement with experimental small-angle X-ray scattering (SAXS) data demonstrating molecule monodispersity and an almost spherical shape. It was confirmed that the glass transition temperature is independent of the dendrimer generation, but is greatly affected by the chemical nature of the dendrimer terminal groups. A sharp increase in the zero-shear viscosity of dendrimer melts was found between the 5th and the 7th dendrimer generations, which was qualitatively identical to that previously reported for polycarbosilane dendrimers with butyl terminal groups. The viscoelastic properties of high-generation dendrimers seem to follow some general trends with an increase in the generation number, which are determined by the regular branching structure of dendrimers.

Nonwoven Materials Produced by Melt Electrospinning of Polypropylene Filled with Calcium Carbonate.

Nowadays, polypropylene-based nonwovens are used in many areas, from filtration to medicine. One of the methods for obtaining such materials is melt electrospinning. In some cases, it is especially interesting to produce composite fibers with a high degree of filling. In this work, the influence of the filling degree of isotactic polypropylene with calcium carbonate on the structure and properties of nonwoven materials obtained by melt electrospinning was studied. It was shown that electrospinning is possible, even at a filler content of 50%, while the average diameter of the fibers increases with the growth in the content of calcium carbonate. The addition of sodium stearate significantly reduces the diameter of the fibers (from 10-65 to 2-10 microns) due to reducing viscosity and increasing the electrical conductivity of the melt. Wide-angle X-ray diffraction analysis and IR spectroscopy reveal that the initial polymer and composites are characterized by the presence of stable α-form crystals, while nonwovens show a predominance of smectic mesophase. The addition of calcium carbonate leads to an increase in the hydrophobicity of the composite films, the addition of sodium stearate results in a decrease of hydrophobicity, while all nonwovens demonstrate superhydrophobic properties.

Non-woven bilayered biodegradable chitosan-gelatin-polylactide scaffold for bioengineering of tracheal epithelium.

OBJECTIVES: The conversion of tissue engineering into a routine clinical tool cannot be achieved without a deep understanding of the interaction between cells and scaffolds during the process of tissue formation in an artificial environment. Here, we have investigated the cultivation conditions and structural features of the biodegradable non-woven material in order to obtain a well-differentiated human airway epithelium. MATERIALS AND METHODS: The bilayered scaffold was fabricated by electrospinning technology. The efficiency of the scaffold has been evaluated using MTT cell proliferation assay, histology, immunofluorescence and electron microscopy. RESULTS: With the use of a copolymer of chitosan-gelatin-poly-l-lactide, a bilayered non-woven scaffold was generated and characterized. The optimal structural parameters of both layers for cell proliferation and differentiation were determined. The basal airway epithelial cells differentiated into ciliary and goblet cells and formed pseudostratified epithelial layer on the surface of the scaffold. In addition, keratinocytes formed a skin equivalent when seeded on the same scaffold. A comparative analysis of growth and differentiation for both types of epithelium was performed. CONCLUSIONS: The structural parameters of nanofibres should be selected experimentally depending on polymer composition. The major challenges on the way to obtain the well-differentiated equivalent of respiratory epithelium on non-woven scaffold include the following: the balance between scaffold permeability and thickness, proper combination of synthetic and natural components, and culture conditions sufficient for co-culturing of airway epithelial cells and fibroblasts. For generation of skin equivalent, the lack of diffusion is not so critical as for pseudostratified airway epithelium.

Multi-hierarchical tissue-engineering ECM-like scaffolds based on cellulose acetate with collagen and chitosan fillers.

A novel high-tech composite biomimetic matrixes for a wide range of medical purposes were prepared. The structure of scaffolds was inspired by the architecture of native decellularized tissue: material consists of a sponge and fibrous components of different spatial geometry based on cellulose acetate with collagen or chitosan filler. The fibrous component was prepared by electrospinning, the sponge - freeze-drying technique. The influence of main technological parameters, such as freeze mode, polymer type and concentration, etc. on the fiber-sponge architecture and properties was examined. It was shown that scaffolds with different types of microstructure can be obtained employing this technique. The impregnation of chitosan or collagen filler in fiber matrix also significantly improves mechanical properties up to 40 MPa for strength and 600 MPa for Young's modulus.

Fabrication and mechanical properties of composite based on ß-chitin and polyacrylic acid.

Squid ß-chitin has been exfoliated in aqueous acrylic acid (AA), after which a composite film of chitin microfibrils in polyacrylic acid (PAA) has been prepared by in situ polymerization of the AA. The segregated chitin fibrils in the composite are 4-6nm in diameter, with an aspect ratio >250. After drying cast films of the composites containing 1, 2 and 3% (w/w) chitin at 140°C for four hours, there was a dramatic resistance to swelling in water, in that the dried films showed only small changes in shape and properties after four hours immersed in water.The most profound impact of the reinforcement on the mechanical properties is observed at high relative humidity (RH), when the PAA is in the rubbery state. At 97.5% RH and room temperature, the elastic moduli of the composites with 1, 2 and 3% (w/w) chitin were 150, 230 and 2100MPa respectively, compared to 65MPa for pure PAA. The main contribution to the filler-reinforcing effect is the high aspect ratio of fibrils and non-covalent interactions, but the stability in water suggests the presence of chemical bonding between the PAA and chitin.

Cold Crystallization of Glassy Polylactide during Solvent Crazing.

Uniaxial tension accompanied by the orientation and crystallization of polymer chains is one of the powerful methods for the improvement of mechanical properties. Crystallization of amorphous isotropic polylactide (PLA) at room temperature is studied for the first time during the drawing of films in the presence of liquid adsorption-active media (ethanol, water-ethanol mixtures, and n-heptane) by the solvent crazing mechanism. The crystalline structure arises only under simultaneous actions of a liquid medium and a tensile stress and does not depend on the nature of the environment. The degree of polymer crystallinity increases nearly linearly with the growth in the fraction of the fibrillar material and reaches a maximum value of 42-45%. It has been stated that polymer crystallization happens in crazes involving nanofibrils with a diameter of about 10-20 nm without affecting the bulk polymer parts. Wide-angle X-ray scattering has been used to confirm that the crazing-induced crystallization is accompanied by the formation of the α'-crystalline phase with crystallite sizes (X-ray coherent scattering region) of 3-5 nm, depending on the nature of the liquid medium. After stretching in liquid media to a high tensile strain, the strength of a PLA film has increased to 200 MPa.

Structure of ß-chitin from Berryteuthis magister and its transformation during whisker preparation and polymerization filling.

Models for the structures of the ß-chitin-protein complex of native and deproteinized squid pen (Berryteuthis magister) based on SAXS and WAXS data are proposed. Chitin fibrils of 25 Å in diameter and persistence length of 1200 Å are immersed in protein matrix. Average distance between fibrils is 42 Å. Deproteinization of the squid pen led to disappearance of the lateral fibril order stabilized by the protein matrix of the native sample. Swelling in water and acrylic acid resulted in an increase in the chitin 010 D-spacing to 14 and 18 Å, respectively. A preparation routine for individual chitin nanofibers of few microns in length and with diameter of 40-60 Å has been developed. During exfoliation of the chitin in acrylic acid the degree of acetylation does not change. Chitin-based nanocomposites can be prepared by polymerization of acrylic acid in swelled deproteinized samples which takes place mainly in the interfibrillar space of ß-chitin mainly.